Effect of liquid inhibitors on PCDD/F formation. Prediction of particle-phase PCDD/F concentrations using PLS modelling with gas-phase chlorophenol concentrations as independent variables

Emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) from municipal waste incineration are currently a subject of considerable public concern because of their extreme toxicity. PCDD/F formation in incineration processes is being studied widely, but little work has been done on their inhibition. We studied the effect of two liquid inhibitors, sodium ammonium hydrogen phosphate (NAHF) and urea (H2NCONH2), on PCDD/F formation in the combustion of liquid fuel doped with copper and chlorine using a pilot-scale plant. The inhibitors were injected into the flue gas stream at a temperature of 725 degrees C, whereupon both the chlorophenol and PCDD/F concentrations decreased. Particle-phase PCDD/F concentrations in particular decreased by up to 90% with NAHF and 70% with urea, but gas phase reduction took place only with urea. The results suggest that the formation of PCDD/Fs is hindered in the particle phase at the early stages of the PCDD/F formation chain, probably even before precursors such as chlorophenols have been formed. As a consequence, particle-phase PCDD/F concentrations can be predicted by a PLS (partial least-squares) approach with the gas-phase chlorophenol concentrations as independent variables. The structure and partial charges of Cu(+)-urea complex were calculated by the HF/3-21G basis set.     

PCDD/F reduction in incinerator flue gas by adding urea to RDF feedstock

The effect of urea on PCDD/F formation in a pilot incinerator was studied by incinerating urea with refuse-derived fuel (RDF) at three concentrations (0.1%, 0.5% and 1.0%, of the fuel feed). A distinct reduction in both PCDD/F and chlorophenol concentrations could be noticed when urea was introduced into the system. Partial-least-square (PLS) analysis of the data showed the importance of certain chlorophenol isomers as PCDD/F precursors, pointing to the possibility that the impact point of the urea inhibitor could be before the precursor molecules, i.e. chlorophenols, have been formed.     

Atmospheric fate and transport of dioxins: local impacts

We conducted model simulations of the atmospheric fate and transport of PCDD/F to assess the fraction of emitted PCDD/F that would deposit within 100 km from the source. We considered eight major categories of PCDD/F emission sources and six different locations, to cover a wide range of source characteristics, PCDD/F congener profiles and particle size distributions, meteorological conditions and terrain configurations. These results suggest that for sources that have tall stacks and/or high plume rise (e.g., copper smelters, cement kilns, sinter plants), only a small fraction of PCDD/F emissions is deposited locally (typically, less than 10% within 100 km). Other source categories such as municipal solid waste incinerators, medical waste incinerators and diesel trucks lead to a greater fraction of PCDD/F being deposited locally; nevertheless, the majority of their PCDD/F emissions tends to be transported beyond 100 km. Although local impacts may need to be addressed for these latter source categories, it appears that the long-range potential impacts of PCDD/F need to be addressed for all source categories. Sensitivity studies were conducted to investigate the effect of various key model inputs on simulation results. These studies suggest that an advanced atmospheric dispersion model should be used for cases where PCDD/F emissions may present some local concerns because the results are very sensitive to the treatment of dispersion. Also, it is essential to obtain accurate characterizations of the particle size distribution of particulate PCDD/F because the dry deposition flux is very sensitive to the particle size distribution.     

Urea as a PCDD/F inhibitor in municipal waste incineration

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from municipal waste incineration have been widely studied because of their extensive toxicity, and many efforts have been made to restrict their emissions. Although a number of chemical compounds have been shown in laboratory-scale tests to inhibit the formation of PCDD/Fs, few have been tested in pilot- or full-scale plants. This work evaluates the effect of urea as a PCDD/F inhibitor in a pilot-scale incinerator that uses refuse-derived fuel (RDF). The decomposition of urea under the test conditions was also studied using detailed kinetic modeling. An aqueous solution of urea was injected into the flue gas stream after the furnace at approximately 730 degrees C, with varied urea concentrations and flue gas residence times used between the furnace and the sampling point. The results demonstrate that urea can successfully inhibit PCDD/F formation in waste incineration if concentrations and injection points are properly adjusted. The kinetic model showed that urea can be rapidly decomposed under appropriate flue gas conditions, indicating that in addition to the urea molecule itself, decomposition products of urea can also be responsible for the reduction of PCDD/F production during incineration.     

Urea as a PCDD/F Inhibitor in Municipal Waste Incineration

ABSTRACT

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from municipal waste incineration have been widely studied because of their extensive toxicity, and many efforts have been made to restrict their emissions. Although a number of chemical compounds have been shown in laboratory-scale tests to inhibit the formation of PCDD/Fs, few have been tested in pilot- or full-scale plants. This work evaluates the effect of urea as a PCDD/F inhibitor in a pilot-scale incinerator that uses refuse-derived fuel (RDF). The decomposition of urea under the test conditions was also studied using detailed kinetic modeling. An aqueous solution of urea was injected into the flue gas stream after the furnace at ~730 °C, with varied urea concentrations and flue gas residence times used between the furnace and the sampling point. The results demonstrate that urea can successfully inhibit PCDD/F formation in waste incineration if concentrations and injection points are properly adjusted. The kinetic model showed that urea can be rapidly decomposed under appropriate flue gas conditions, indicating that in addition to the urea molecule itself, decomposition products of urea can also be responsible for the reduction of PCDD/F production during incineration.     

Characterization of polychlorinated dibenzo-p-dioxins and dibenzofurans in different particle size fractions of marine sediments

The distribution of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) was examined according to particle size in marine sediments, with a particular focus on fine particulates. Samples from different coastal sites were fractionated into five size groups (<2, 2-5, 5-10, 10-20, and 20-63 microm diameter) by gravitational split-flow thin fractionation. Despite the different size profiles and PCDD/F contents of the sediments at each site, PCDD/F levels in fractionations tended to increase as the particle size decreased; the PCDD/F levels in the finest particles were up to 16 times higher than in the coarsest particles, which was associated with their organic carbon contents. Log normalization showed high levels of PCDD/Fs in the fine silt particles (2-10 microm), which are consumable by aquatic biota. Because of the different toxicity and bioavailability of PCDD/Fs in different sediment particle sizes, it is important to study particle actions to understand their effects on the aquatic ecosystem.     

PCDD/F inhibition by prior addition of urea to the solid fuel in laboratory experiments and results statistical evaluation

The objectives of this work were to study the effect of urea addition to the fuel before the combustion on the suppression of PCDD/F emissions, to examine the influence of urea to PCDD/F isomer patterns by employing statistical analysis techniques and to determine the most effective method of urea addition. Urea in the form of powder and as an aqueous solution was mixed with RDF and the fuel mixtures were incinerated in a lab-scale reactor at 1000 degrees C. PCDD/F emitted during combustion experiments were collected in a quartz wool filter downstream the reactor unit. Analysis and quantification of PCDD/F showed that urea significantly affected PCDD/F emissions. Combustion of RDF containing 10% w/w urea resulted in PCDD/F emissions lower than 8 I-TEQ ng/g RDF, while the corresponding average value from single RDF combustion was 17 I-TEQ ng/g RDF. The PCDD/F prevention capacity of urea was independent from the method of urea addition to the fuel, as similar results were obtained after the addition of urea in the solid and in the aqueous phases. Results assessment by statistical methods showed that isomer patterns remained almost stable and were not affected by the method of urea addition.     

The size distribution of polychlorinated dibenzo-p-dioxins and dibenzofurans in the bottom ash of municipal solid waste incinerators

In this study, bottom ash was sampled from two Taiwanese municipal solid waste incinerators (MSWIs: A and B) and sieved to size classes of 4.75-9.5 mm, 2.36-4.75 mm, 1.0-2.36 mm, 0.6-1.0 mm, 0.3-0.6 mm, 0.21-0.3 mm, 0.125-0.21 mm, 0.075-0.125 mm and <0.074 mm. For both MSWIs, the major peak in the particle size distribution for the PCDD/F content was found in a particle size <0.21 mm, that is, 16.1 (A) and 4.37 pg I-TEQ/g (B). This is due to the fact that a smaller particle has higher specific surface area thus offering more adsorption sites. The mean cumulative fractions (F%) of PCDD/F I-TEQ in the bottom ash of MSWI A and B in the particle size range below 0.6, 2.36 and 4.75 mm, in sequence, are 40.4%, 77.2% and 95.6%, respectively. We suggest sieving the bottom ash before the subsequent reutilization at the suggested cut size of 0.6 mm. In the view of PCDD/Fs, bottom ash with a particle size larger than 0.6 mm, which is the more non-hazardous part, may be suitable for being the raw material of landfilling soil, road sub-base, and construction blocks. For the minus 0.6 mm fraction, vitrification with fly ash is one of the choices.     

Modeling the atmospheric transport and deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans in North America

The atmospheric fate of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) was simulated for the year 2000 in North America using a SMOKE/CMAQ-based chemical transport model that was modified for this purpose. The 1999 USEPA emission inventories of PCDD/Fs and criteria pollutants were used. The 1995 Canadian emission inventory of criteria pollutants and the 1995 Canadian area source emissions for PCDD/Fs were used with the 2000 Canadian point source emissions. Modifications to CMAQ involved coupling it with dual organic matter (OM) absorption and black carbon (BC) adsorption models to calculate PCDD/F gas–particle partitioning. The model satisfactorily reproduced the particle bound fractions at all rural sites for which there were measured data and across the whole domain, the modeled vs. measured differences in particle bound fractions were less than 20% for nearly all congeners. The model predicted ambient air PCDD/F concentrations were also consistent with measurements. Simulated deposition fluxes were within 58% of direct measurements. PCDD/F atmospheric depositions to each of the Great Lakes were estimated for the year 2000. The results indicate that approximately 76% of the total deposition of PCDD/Fs to the Great Lakes (in W-TEQ, or toxic equivalent units as defined by the World Health Organization) is attributed to PCDD/Fs absorbed into OM in aerosol. For all of the lakes, more than 92% of all deposition is particle phase wet deposition and only 5–8% is particle phase dry deposition. Wet deposition from the gas phase is negligible. Of the 17 toxic PCDD/F congeners, the Cl_4–5DD/F compounds contribute approximately 70% to the total atmospheric deposition to the Great Lakes. The seasonal changes in the PCDD/F deposition flux track variations in ambient temperature.     

Effect of dissolved humic matters on the leachability of PCDD/F from fly ash--laboratory experiment using Aldrich humic acid

The effect of dissolved humic matters (DHM) on the leachability of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) in fly ash was studied theoretically and in laboratorial condition to verify the previous results for pilot and field experiment of incineration residues landfill. In theoretical review, it was shown that DHM could influence the actual solubility and leachability of PCDD/F. The higher concentration of DHM showed the higher leachability of PCDD/F. In the leaching test, three different DHM concentrations and pHs of solutions were adopted to fly ash samples imaging the various characteristics of municipal solid waste leachate. It was proved experimentally that the leachability of PCDD/F increased with increasing DHM concentration in all pH conditions. The highest leachability was shown at the highest pH. Isomer distribution patterns of PCDD/F in all leachates were similar in all pH conditions. It backed up the distribution theory of PCDD/F between DHM and water.     

Adsorption of PCDD/F on MWI fly ash

The removal of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) from waste incinerator off-gas is a costly task, because a considerable part of the PCDD/F may exist in the gas phase (often 50-100% around 200 degrees C). The volatile fraction passes the particle filter and the subsequent gas cleaning equipment, so that an additional unit is needed to remove the gaseous PCDD/F from the flue gas. Moreover, dioxins and furans can accumulate in some parts of the equipment in a way that they can act as a latent source. In this work, we investigate the possibility to adsorb the PCDD/F at the fly ash particles and to remove them during the filtration. The gas/particle partitioning of the PCDD/F depends on the temperature, the vapor pressure, the particle size, the particle number density and on the physical and chemical properties of the particle surface. These relationships are investigated by model calculations and by pilot scale experiments (500 Nm3/h) which employ one selected hexachlorinated dioxin congener. At room temperature, approx. 90% of the HxCDD are found in the particulate phase, while at 135 degrees C that portion is only 10%. This means that at ambient temperatures, the gas/particle partitioning of the dioxin corresponds well to the sublimation equilibrium. At higher temperatures, it is much different from the sublimation equilibrium and the apparent adsorption enthalpy is smaller than the enthalpy of sublimation. This observation is in agreement with literature data. From the above experiments and from similar literature data, the efficiency of fly ash particles as a sink for PCDD/F can be evaluated. The data suggest that the adsorption rate is not the limiting factor for the transfer into the particulate phase. The important factors appear to be the chemical composition of the fly ash and the temperature.     

Precipitation scavenging of particle-bound contaminants – A case study of PCDD/Fs

Precipitation scavenging of particles is a major mechanism for atmospheric deposition of organic contaminants, but there have been few field studies. We studied precipitation scavenging of PCDD/Fs with the aim of deepening understanding of environmental variables influencing this process. Bulk deposition of PCDD/Fs and their concentrations in ambient air measured at a background site in Sweden were used to calculate precipitation scavenging ratios. Contrary to expectations, increasing scavenging ratios with decreasing degree of chlorination of the PCDD/F congeners were observed when the particle-associated PCDD/F concentrations in air were used for the calculation. This was attributed to differences in temperature and thereby in the gas – particle partitioning of the PCDD/Fs between ground level and clouds where much of the particle scavenging occurs. When the particle-associated PCDD/F concentrations were recalculated for a 10–20 °C lower temperature, the scavenging ratios of the different PCDD/F congeners were similar. Hence differences between ground level and in-cloud temperature should be considered when calculating scavenging ratios from field observations and when modeling this process. The scavenging ratios averaged ～200 000, with lower values when the particle-associated PCDD/F concentration in air was lower. The soot concentration in air was a good predictor of bulk deposition of PCDD/Fs.     

Quasi-dynamic leaching characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans from raw and solidified waste incineration residues

Quasi-dynamic leaching characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from raw and solidified air pollution control (APC) residues were examined via a nine-time multiple leaching test. The effect of injected activated carbon in the APC residues on the PCDD/F leachability was also evaluated. When humic acid solution was used as a leachant, the leaching concentrations of PCDD/Fs fluctuated between the first and the fifth leaching, followed by a gradual increase and then suddenly reached maximum values at the leaching sequences around seventh and eighth. This significant enhancement in PCDD/F leachability was mainly due to an increase in the release of highly chlorinated PCDD/Fs. Leaching of PCDD/Fs with n-hexane was, in contrast, primarily caused by the partitioning of hydrophobic PCDD/Fs between the APC residue surface and the liquid phase of n-hexane. Consequently, the largest leaching concentrations for n-hexane tests achieved at the first leaching, followed by a decrease and reached plateaus. Solidification/stabilization (S/S) decreased the PCDD/F leachability up to the fifth leaching by the use of humic acid solution. However, S/S increased the PCDD/F leaching concentrations and rates with n-hexane. The activated carbon in APC residues significantly inhibited the release of PCDD/F with n-hexane. The inhibiting effect provided by activated carbon was, however, less significant by the use of humic acid solution.     

Air-vegetation transfer of PCDD/PCDFs: an assessment of field data and implications for modeling

This study was designed to evaluate soil and air (gas and particle) transfer of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) to vegetation in residential and industrial areas. In a first part, soil-vegetation transfer was assessed. The levels of PCDD/Fs in 120 soil and 120 herbage samples collected from 1996 to 2002 in an industrial area of Montcada (Barcelona, Spain), near a municipal solid waste incinerator (MSWI), were determined. Some additional individual samples were also evaluated. It was concluded that high soil concentrations, which are not at steady state with the air layer above it, show a tendency for PCDD/Fs to escape via volatilization. In a second part of the study, air-vegetation transfer was examined. PCDD/F concentrations from 24 herbage samples were used, while PCDD/F concentrations were also measured in seven high-volume air samples and seven passive air-vapor samples. Scavenging coefficients (m3 air "sampled"/g grass d.m.) ranged from 1.9 to 11.3 m3/g. A good trend with K(OA) was observed for PCDDs (R=0.82), while it was lower for PCDFs (R=0.55). The current results corroborate that PCDD/F concentrations in vegetation are associated with atmospheric deposition. For the highest substituted PCDD/F congeners, the air-particle uptake from plants is the principal pathway. In regions impacted by combustion emission sources, PCDD/F gas-particle partitioning is influenced by a higher concentration of particles in the air. Particles and associated particle-bound PCDD/Fs would sorb to leaf surfaces, and are subject to removal via wash off. However, in areas where emissions to air are not very notable, vapor absorption would be the principal source of vegetation pollution. The results of this investigation can have a potential interest in risk assessment studies and environmental fate models.     

PCDD/Fs and PCBs in airborne particulate matter of the greater Thessaloniki area, N. Greece

Particle-bound polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polychlorinated biphenyls (PCBs) were monitored at two sites in northern Greece for an eight-month period in 1999. PCDD/F concentrations were close to the lower end of reported values worldwide. Excepting a few cases, the PCDD/Fs homologue profile was stable. The gaseous PCDD/F fractions calculated were found to account for a small percentage of the total concentrations (<2% for OCDD/Fs and HpCDD/Fs, while 30-35% for TCDFs). Particle-bound PCBs were also found at low concentrations which, however, were higher at the urban site. Calculations of the dry deposition of particulate PCDD/ Fs and PCBs gave mean values of 0.52 and 0.59 pg I-TEQ/m2/day of PCDD/Fs, while 242 and 74 pg/m2/day of sigmaPCBs for the urban and the semirural areas respectively. An anticorrelation of PCDD/F concentrations with ambient temperature was derived particularly for the lower chlorinated congeners. A weak association with winds of western and southern origin was also observed. Factor analysis and literature source profiles were employed to identify possible emission sources. It was appeared that the PCDD/F compositional pattern of TSP is influenced by mixed sources the most prominent being uncontrolled fires and car exhausts.     

The historical record of PCB and PCDD/F deposition at Greifensee, a lake of the Swiss plateau, between 1848 and 1999

Dated sediment cores provide an excellent way to investigate the historical input of persistent organic pollutants into the environment and to identify possible sources of pollution. The vertical distribution of polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans (PCDD/F) and polychlorinated biphenyls (PCB) was investigated in a sediment core from Greifensee to elucidate the historical trends of PCDD/F and PCB inputs between 1848 and 1999. Concentrations of PCB and PCDD/F increased by more than one order of magnitude between 1930 and 1960. PCB and PCDD/F concentrations were 5700 ng/kg dry weight (dw) and 160 ng/kg dw, respectively, in sediments originating from the late 1930s and reached a maximum of 130,000 ng/kg dw and 2400 ng/kg dw, respectively, in the early 1960s. From 1960 on, concentrations decreased to the 1930s level by the mid 1980s. A remarkable shift in the PCDD/F pattern was observed after the early 1940s. Before 1940, the PCDD/F pattern was PCDF dominated (ratio of PCDD to PCDF=0.41+/-0.11), while the PCDD started to be the major species after the early 1940s (ratio of PCDD to PCDF=1.46+/-0.38). The temporal trends of PCB and PCDD/F correlate surprisingly well with each other. This might be due to the coincidence of two factors. The introduction of PCB on the market in the 1930s resulted in emissions due to the widespread use of these industrial chemicals. In the same time period, waste incineration became an increasingly popular way to get rid of garbage, boosting the PCDD/F emissions significantly. The rapid decline of PCDD/F and PCB concentrations in the sediment starting in the early 1960s reflects the result of better emission control techniques in thermal processes and the improvement of waste water treatment in the catchment of Greifensee.     

Atmospheric particle size distributions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polycyclic aromatic hydrocarbons (PAHs) and their implications for wet and dry deposition

Concurrent measurements of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polycyclic aromatic hydrocarbons (PAHs) in different size fractions of atmospheric particulate matter are presented for a winter and a summer sampling period. The PCDD/Fs and PAHs were primarily associated with particles of <1.35 μm aerodynamic diameter. The particle size distributions were similar for the compounds within each substance group and, surprisingly, also between the PCDD/Fs and PAHs. Changes in the particle size distribution of particle mass were reflected in the particle size distributions of the PCDD/Fs and PAHs.The data were employed to identify those particle size fractions dominating the wet and dry particle bound deposition of PCDD/Fs and PAHs and, furthermore, to assess the relative contributions of wet and dry deposition to the total particle bound deposition fluxes. The calculations indicate that coarse particles contribute most to the dry deposition while, in contrast, the wet deposition of the PCDD/Fs and PAHs is dominated by fine particles. Furthermore, it is estimated that in Bayreuth wet deposition dominates the total particle bound deposition of PCDD/Fs and PAHs.     

Sampling and analysis of ambient dioxins in northern Taiwan

In this study, ambient air samples were taken concurrently in the vicinity area of a large-scale municipal waste incinerator (MWI) and the background area for measuring polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) concentrations from November 1999 through July 2000 in northern Taiwan. The results obtained from eighteen ambient air samples indicate that the mean PCDD/F concentration of seventeen 2,3,7,8-substituted congeners in wintertime (188–348 fg-I-TEQ/m³) is significantly higher than that measured in summertime (56–166 fg-I-TEQ/m³). In addition, the seasonal PCDD/F concentrations are compared with the ambient air quality data including CO, NO₂, PM₁₀ and TSP sampled from Taipei area to gain better insights. It indicates that the variation of ambient air PCDD/F concentrations is closely correlated with that of PM₁₀ concentrations. Besides, the results indicate that the I-TEQ concentration of ambient air in sampling site B (directly downwind of the MWI) is of the highest while the sampling site A (upwind of MWI) is of the lowest among all sampling sites. This implies that existing MWI can be a significant emitter of PCDD/Fs in this area. Furthermore, the patterns of the PCDD/F congener distribution at all sampling sites (including the background site in Taoyuan) are quite similar. OCDD concentration is of the highest among seventeen PCDD/F congeners investigated and accounts for about 35% of the total concentration. As for the I-TEQ concentrations, 2,3,4,7,8-PeCDF is the most significant contributor, generally being responsible for 30–45% of the total I-TEQ values depending on the sampling sites and seasons.     

Toxic emissions during co-combustion of biomass-waste wood-lignite blends in an industrial boiler

The objectives of this work were to study the PCDD/F emissions during the co-combustion of waste wood/coal co-combustion in an industrial boiler and to determine the relation of the toxic emissions to the fuel properties. Co-combustion experiments were performed in a 13.8 MWthermal industrial moving grate combustor. The fuels which were examined in this study included Greek lignite, natural uncontaminated wood, power poles and medium density fibers (MDFs) which were by-products of the plant production process. Fuel blends were prepared by mixing single components in various concentrations. PCDD/F emissions were collected during experimental runs and were analyzed according to standard methods. Low PCDD/F emissions were obtained during the co-combustion tests, lower than the limit value of 0.1 ng TEQ/Nm3. The lowest values were observed during the combustion of fuel blends containing MDF, possibly due to the inhibitory action of some of the N-containing MDF ingredients, such as urea. No direct correlation was found between the PCDD/F and the copper emissions, while examination of the PCDD/F homologue patterns revealed the predominance of the lower chlorinated isomers over the higher ones.     

Investigating differential binding of polychlorinated dibenzo-p-dioxins/dibenzofurans in soil and soil components using selective supercritical fluid extraction

Supercritical fluid extraction (SFE) with pure carbon dioxide was performed at increasingly strong conditions to investigate differential binding of polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) in two impacted soils, in their sieved size fractions, and in small (a few mg) samples of industry-related waste products separated from impacted soil. The binding strengths of PCDD/Fs were shown to be different in the two soils, and in their different soil particle size fractions. As might be expected based on surface area considerations, one soil showed the strongest binding in the smallest (<5 μm) sieved fraction. However, the other soil showed the strongest binding in the larger sized fractions, possibly indicating that process-related particles could be controlling PCDD/F binding. Selective SFE of various types of particles including black carbon and charcoal (separated from soil), and from a suspected process anode residue did show different PCDD/F binding behavior ranging from quite weak binding (charcoal) to very strong binding (anode particles). Shifts to the stronger SFE fractions in the soils after activated carbon treatment agreed well with the decreases previously found in the uptake of PCDD/Fs by earthworms, as well as decreases in their freely-dissolved aqueous concentrations in soil/water slurries. These results show that, as previously demonstrated for PAHs and PCBs, selective SFE can be a useful tool to investigate differences in PCDD/F binding behaviors in impacted soils and sediments and their component parts, as well as a rapid tool for estimating the effectiveness of activated carbon treatments on decreasing the bioavailability of PCDD/Fs in soils and sediments.