沉淀—电解法回收COD分析废液中的银

采用沉淀－电解法从ＣＯＤ分析废液中回收银。首先将废液中银沉淀析出，制成高浓度含银电解液，然后以不锈钢作阴、阳极，在极距１０ｍｍ、电流密度０．２８Ａ／ｄｍ＾２条件下进行电解，回收废液中银。该方法操作简便，银回收率为９５％以上，纯度达９９．５％以上。     

用硝酸银消除高浓度氯离子对COD测定的干扰及测定废液中银的回收

分析了氯离子的干扰机理,提出了用硝酸银代替硫酸汞消除氯离子干扰测定高氯离子水样COD的分析方法,同时对COD废液的处理及废液中银的回收利用进行了研究。实验结果表明,该法具有较好的准确性和重复性,其相对误差均在国家规定的允许范围内;COD废液中的银经分离后,用Zn—H2SO4体系还原回收,银回收率为94．8％,回收的银粉纯度为99．6％,且可实现COD废液中银的循环使用。     

从铜氨废液中回收铜

分别采用化学沉淀法和电解法从电镀污泥水热合成铁氧体后过滤分离的铜氨废液中回收铜。实验结果表明：采用化学沉淀法处理铜氨废液,以体积比为1：1的盐酸调节铜氨废液pH为5．4～6．4,沉淀出碱式氯化铜固体,铜回收率在98％以上,1L铜氨废液可回收碱式氯化铜5．83g（合铜3．50g）;采用电解法处理铜氨废液,在电流密度250A／m^2、电解时间5h、电解温度60℃的条件下,1L铜氨废液可回收3．54g铜粉,铜回收率超过99％,铜粉的粒径和纯度均可达到GB5246-85《电解铜粉》的要求。     

光催化净水材料MoO3的制备及应用方法

该发明公开了一种光催化净水材料MoO3的制备及应用方法：在室温下制备钼酸铵水溶液，向其中添加表面活性剂十六烷基三甲基溴化铵，混合均匀；搅拌下滴加稀盐酸溶液，至出现大量沉淀，收集沉淀物，反复洗涤、干燥，制得前驱物；焙烧前驱物，获得光催化净水材料MoO3。该光催化净水材料可用于含有机染料的废液的处理，对各有机染料的脱色率均达到80％以上，     

维生素B12发酵废液治理技术

筛选了一株能较好利用维生素B12发酵废液并能得到单细胞菌体蛋白(SCP)的菌株。通过正交试验研究该菌株，得到其利用废液的最佳发酵条件。研究结果表明，使用该菌株能大大降低发酵废液的化学需氧量(COD)，COD去除率达到90％以上，有效减少或消除废液对环境的污染。     

利用味精废液生产高蛋白秸秆生物饲料的方法

该发明公开了一种利用味精废液生产高蛋白秸秆生物饲料的方法。其制备步骤如下：将味精废液、发酵剂喷洒到秸秆或秸秆粉上拌匀,加水搅拌后装袋密封、堆放发酵,其中原料的质量比为秸秆70—90份、味精废液10～30份,发酵剂为秸秆或秸秆粉质量的0．2％～1．0％。该发明综合利用味精废液和农作物秸秆两大污染环境的有机废弃物,生产高蛋白秸秆生物饲料,饲料蛋白含量高,     

盐效萃取法从电子产品清洗废液中回收异丙醇

用盐效萃取法从电子产品清洗废液中回收片丙醇,考察了碳酸钾水溶液与该清洗废液的质量比对脱水率的影响,测定了异丙醇-水-碳酸钾体系存40℃时的液液相平衡数据,用Pitzer理论和NRTL方程对液液相平衡数据进行了理论计算。结果表明：当质量分数为60．00％的碳酸钾水溶液与该废液的质晕比为2．00时,脱水率高达90．00％;将有机相进行精馏可得到质量分数为99．50％的异丙醇;计算值与实测值接近,水相和有机相的绝对平均偏差分别为0．62％和0．46％。     

氯化钡废液联产氢氧化钙和氯化钡

讨论了氯化钡废液联产氢氧化钙及高纯氯化钡的方法和主要影响因素。通过复盐共沉淀、热滤、结晶、精制纯化等工序,用氯化钡的蒸发残液制得了工业级的氢氧化钙和高纯度氯化钡,其纯度分别达95％和99．92％以上。采用有机溶剂析出法精制氯化钡,无需重结晶工序,是对传统工艺的一种改进。     

环氧丙烷生产废液中1,2 -二氯丙烷的回收

介绍了从环氧丙烷生产废液中回收1,2-二氯丙烷的新方法。采用常压精馏、减压精馏、共沸精馏工艺分离环氧丙烷生产废液中的1,2-二氯丙烷。实验结果显示,共沸精馏工艺的效果最好;在含有一定量的共沸剂、釜温100℃、顶温86℃、回流比为1的条件下,塔顶馏分中1,2-二氯丙烷的质量分数可达到98％以上,1,2-二氯丙烷的回收率可达到97％以上。     

蚀刻液水合肼还原除铜

将电路板厂废弃的蚀刻液,经氢氧化铜沉淀法回收大部分铜后,再采用水合肼还原,进一步除铜。反应温度为50℃,水合肼质量分数为3．0％,溶液pH为6．0,废液中铜的去除率可达98.5％,处理后废液中铜的质量浓度低于0．2g／L,可作为碱性蚀刻液重复利用。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.