Effects of operating variables on PAH emissions and mutagenicity of emissions from woodstoves.

As part of the Integrated Air Cancer Project, the U.S. Environmental Protection Agency (EPA) has conducted field emission measurement programs in Raleigh, North Carolina, and Boise, Idaho, to identify the potential mutagenic impact of residential wood burning and motor vehicles on ambient and indoor air. These studies included the collection of emission samples from chimneys serving wood burning appliances. Parallel projects were undertaken in instrumented woodstove test laboratories to quantify woodstove emissions during operations typical of in-house usage but under more controlled conditions. Three woodstoves were operated in test laboratories over a range of burnrates, burning eastern oak, southern yellow pine, or western white pine. Two conventional stoves were tested at an altitude of 90 m. One of the conventional stoves and a catalytic stove were tested at an altitude of 825 m. Decreasing burnrate increased total particulate emissions from the conventional stoves while the catalytic stove's total particulate emissions were unaffected. There was no correlation of total particulate emissions with altitude whereas total polynuclear aromatic hydrocarbon (PAH) emissions were higher at the lower altitude. Mutagenicity of the catalytic stove emissions was higher than emissions from the conventional stove. Emissions from burning pine were more mutagenic than emissions from oak.     

Effects of Operating Variables on PAH Emissions and Mutagenicity of Emissions from Woodstoves

As part of the Integrated Air Cancer Project, the U.S. Environmental Protection Agency (EPA) has conducted field emission measurement programs in Raleigh, North Carolina, and Boise, Idaho, to identify the potential mutagenic Impact of residential wood burning and motor vehicles on ambient and indoor air. These studies included the collection of emission samples from chimneys serving wood burning appliances. Parallel projects were undertaken in Instrumented woodstove test laboratories to quantify woodstove emissions during operations typical of in-house usage but under more controlled conditions.

Three woodstoves were operated In test laboratories over a range of burnrates, burning eastern oak, southern yellow pine, or western white pine. Two conventional stoves were tested at an altitude of 90 m. One of the conventional stoves and a catalytic stove were tested at an altitude of 825 m.

Decreasing burnrate increased total paniculate emissions from the conventional stoves while the catalytic stove's total particulate emissions were unaffected. There was no correlation of total particulate emissions with altitude whereas total polynuclear aromatic hydrocarbon (PAH) emissions were higher at the lower altitude. Mutagenicity of the catalytic stove emissions was higher than emissions from the conventional stove. Emissions from burning pine were more mutagenic than emissions from oak.     

Emission factors of particulate matter,polycyclic aromatic hydrocarbons,and levoglucosan from wood combustion in south-central Chile

In south-central Chile, wood stoves have been identified as an important source of air pollution in populated areas. Eucalyptus (Eucalyptus globulus), Chilean oak (Nothofagus oblique), and mimosa (Acacia dealbata) were burned in a single-chamber slow-combustion wood stove at a controlled testing facility located at the University of Concepción, Chile. In each experiment, 2.7–3.1 kg of firewood were combusted while continuously monitoring temperature, exhaust gases, burn rate, and collecting particulate matter samples in Teflon filters under isokinetic conditions for polycyclic aromatic hydrocarbon and levoglucosan analyses. Mean particulate matter emission factors were 2.03, 4.06, and 3.84 g/kg dry wood for eucalyptus, oak, and mimosa, respectively. The emission factors were inversely correlated with combustion efficiency. The mean emission factors of the sums of 12 polycyclic aromatic hydrocarbons in particle phases were 1472.5, 2134.0, and 747.5 μg/kg for eucalyptus, oak, and mimosa, respectively. Fluoranthene, pyrene, benzo[a]anthracene, and chrysene were present in the particle phase in higher proportions compared with other polycyclic aromatic hydrocarbons that were analyzed. Mean levoglucosan emission factors were 854.9, 202.3, and 328.0 mg/kg for eucalyptus, oak, and mimosa, respectively. Since the emissions of particulate matter and other pollutants were inversely correlated with combustion efficiency, implementing more efficient technologies would help to reduce air pollutant emissions from wood combustion.

Implications: Residential wood burning has been identified as a significant source of air pollution in populated areas. Local wood species are combusted for home cooking and heating, which releases several toxic air pollutants, including particulate matter, carbon monoxide, and polycyclic aromatic hydrocarbons. Air pollutant emissions depend on the type of wood and the technology and operational conditions of the wood stove. A better understanding of emissions from local wood species and wood stove performance would help to identify better biomass fuels and wood stove technologies in order to reduce air pollution from residential wood burning.     

Polycyclic aromatic hydrocarbons in atmospheric particles in the metropolitan area of Porto Alegre,Brazil

The aim of the present study is to identify and quantify the main sources of polycyclic aromatic hydrocarbons (PAHs) associated with aerosols (PM₁₀) collected at three different sampling stations: 8° Distrito, CEASA and Charqueadas. The samples were collected between November 2001 and November 2002, and the concentrations of 16 major PAHs were determined according to EPA. The filters containing particulate matter were extracted with dichloromethane in Soxhlet and the extracts were later analysed in a gaseous chromatograph coupled to a mass spectrometer (GS/MS). The average concentrations of PAHs ranged between 0.04 and 2.30 ng m⁻³. The analysis of principal components was applied to the chemical and meteorological variables in order to facilitate the identification of sources of PAHs emission into the atmospheric particulate. The study identified the following sources of PAHs: vehicular emissions, such as diesel oil, petrol, alcohol, and kerosene; industrial emissions, like lubricating oils; emissions from hospital waste burning, and coal burning at power plants.     

Emissions from Burning Grass Stubble and Straw

The emissions from burning the residue following grass-seed harvest were determined by means of a combined laboratory-field study. Samples of the straw and stubble residue were burned in the laboratory burning tower at the University of California at Riverside. Complete analyses were determined for gaseous and particulate emissions for the important grass species from the Willamette Valley of Oregon. Particulate emissions averaged 15.6 lb/ton of fuel burned. Carbon monoxide averaged 101 lb/ton of fuel burned. Hydrocarbon emission averages, in pounds per ton of fuel burned, were 1.74 for saturates plus acetylene, 2.80 for defines, and 1.68 for ethylene. The NO_x emission, at the temperature peak during the burn, averaged 29.3 ppm. Field studies, conducted by personnel from Oregon State University, measured only particulate emissions, carbon dioxide, and temperature over the burn. The carbon dioxide values were found to be similar to those obtained on the burning table at UCR and it was therefore concluded that the other gaseous emissions were similar and could be used as reasonably accurate for emission inventories. The temperature values obtained in the laboratory and field were also similar and further justifies extrapolating the burning table data to field situations. The particulate matter collected in the field studies averaged 15.55 lb of particulate per ton of fuel burned. This is the same average obtained for the burning table data which again serves to validate the emissions reported from Riverside. Much more variability was found in the particulate emissions obtained in the field which reflects the wider range of environmental conditions encountered in the field.     

Atmospheric concentrations,gaseous–particulate distribution,and carcinogenic potential of polycyclic aromatic hydrocarbons in Assiut,Egypt

The concentrations of 15 priority PAHs were determined in the atmospheric gaseous and particulate phases from nine sites across Assiut City, Egypt. While naphthalene, acenaphthene, and fluorene were the most abundant in the gaseous phase with average concentrations of 377, 184, and 181 ng/m³, benzo[b]fluoranthene, chrysene, and benzo[g,h,i]perylene showed the highest levels in the particulate phase with average concentrations of 76, 6, and 52 ng/m³. The average total atmospheric concentration of target PAHs (1,590 ng/m³) indicates that Assiut is one of the highest PAH-contaminated areas in the world. Statistical analysis revealed a significant difference between the levels of PAHs in the atmosphere of urban and suburban sites (P?=?0.029 and 0.043 for gaseous and particulate phases, respectively). Investigation of diagnostic PAH concentration ratios revealed vehicular combustion and traffic exhaust emissions as the major sources of PAHs with a higher contribution of gasoline rather than diesel vehicles in the sampled areas. Benzo[a]pyrene has the highest contribution (average?=?32, 4 % for gaseous and particulate phases) to the total carcinogenic activity (TCA) of atmospheric PAHs. While particulate phase PAHs have higher contribution to the TCA, gaseous phase PAHs present at higher concentrations in the atmosphere are more capable of undergoing atmospheric reactions to form more toxic derivatives.     

Effects of open burning of rice straw on concentrations of atmospheric polycyclic aromatic hydrocarbons in central Taiwan

The sizes and concentrations of 21 atmospheric polycyclic aromatic hydrocarbons (PAHs) were measured at Jhu-Shan (a rural site) and Sin-Gang (a town site) in central Taiwan in October and December 2005. Air samples were collected using semi-volatile sampling trains (PS-1 sampler) over 16 days for rice-straw burning and nonburning periods. These samples were then analyzed using a gas chromatograph with a flame-ionization detector (GC/FID). Particle-size distributions in the particulate phase show a bimode, peaking at 0.32-0.56 microm and 3.2-5.6 microm at the two sites during the nonburning period. During the burning period, peaks also appeared at 0.32-0.56 microm and 3.2-5.6 microm at Jhu-Shan, with the accumulation mode (particle size between 0.1 and 3.2 microm) accounting for approximately 74.1% of total particle mass. The peaks at 0.18-0.32 microm and 1.8-3.2 microm at Shin-Gang had an accumulation mode accounting for approximately 70.1% of total particle mass. The mass median diameter (MMD) of 3.99-4.35 microm in the particulate phase suggested that rice-straw burning generated increased numbers of coarse particles. The concentrations of total PAHs (sum of 21 gases + particles) at the Jhu-Shan site (Sin-Gang site) were 522.9 +/- 111.4 ng/ml (572.0 +/- 91.0 ng/ml) and 330.1 +/- 17.0 ng/ml (or 427.5 +/- 108.0 ng/ml) during burning and nonburning periods, respectively, accounting for a roughly 58% (or 34%) increase in the concentrations of total PAHs due to rice-straw burning. On average, low-weight PAHs (about 87.0%) represent the largest proportion of total PAHs, followed by medium-weight PAHs (7.1%), and high-weight PAHs (5.9%). Combustion-related PAHs during burning periods were 1.54-2.57 times higher than those during nonburning periods. The results of principal component analysis (PCA)/absolute principal component scores (APCS) suggest that the primary pollution sources at the two sites are similar and include vehicle exhaust, coal/wood combustion, incense burning, and incineration emissions. Open burning of rice straw was estimated to contribute approximately 5.0-33.5% to the total atmospheric PAHs at the two sites.     

Mercury (Hg) emissions from domestic biomass combustion for space heating

Three mercury (Hg) species (gaseous elemental mercury (GEM), gaseous oxidized mercury (GOM), and fine particulate-bound mercury (PBM_2.5)) were measured in the stack of a small scale wood combustion chamber at 400 °C, in the stack of an advanced wood boiler, and in two areas influenced by wood combustion. The low temperature process (lab-scale) emitted mostly GEM (∼99% when burning wood pellets and ∼95% when burning unprocessed wood). The high temperature wood boiler emitted a greater proportion of oxidized Hg (approximately 65%) than the low temperature system. In field measurements, mean PBM_2.5 concentrations at the rural and urban sites in winter were statistically significantly higher than in warmer seasons and were well correlated with Delta-C concentrations, a wood combustion indictor measured by an aethalometer (UV-absorbable carbon minus black carbon). Overall the results suggest that wood combustion may be an important source of oxidized mercury (mostly in the particulate phase) in northern climates in winter.     

Effects of Open Burning of Rice Straw on Concentrations of Atmospheric Polycyclic Aromatic Hydrocarbons in Central Taiwan

Abstract

The sizes and concentrations of 21 atmospheric polycyclic aromatic hydrocarbons (PAHs) were measured at Jhu-Shan (a rural site) and Sin-Gang (a town site) in central Taiwan in October and December 2005. Air samples were collected using semi-volatile sampling trains (PS-1 sampler) over 16 days for rice-straw burning and nonburning periods. These samples were then analyzed using a gas chromatograph with a flame-ionization detector (GC/FID). Particle-size distributions in the particulate phase show a bimode, peaking at 0.32–0.56 μm and 3.2–5.6 μm at the two sites during the nonburning period. During the burning period, peaks also appeared at 0.32–0.56 μm and 3.2–5.6 μm at Jhu-Shan, with the accumulation mode (particle size between 0.1 and 3.2 μm) accounting for approximately 74.1% of total particle mass. The peaks at 0.18–0.32 μm and 1.8–3.2 μm at Shin-Gang had an accumulation mode accounting for approximately 70.1% of total particle mass. The mass median diameter (MMD) of 3.99–4.35 μm in the particulate phase suggested that rice-straw burning generated increased numbers of coarse particles. The concentrations of total PAHs (sum of 21 gases + particles) at the Jhu-Shan site (Sin-Gang site) were 522.9 ± 111.4 ng/m? (572.0 ± 91.0 ng/m?) and 330.1 ± 17.0 ng/m? (or 427.5 ± 108.0 ng/m?) during burning and nonburning periods, respectively, accounting for a roughly 58% (or 34%) increase in the concentrations of total PAHs due to rice-straw burning. On average, low-weight PAHs (about 87.0%) represent the largest proportion of total PAHs, followed by medium-weight PAHs (7.1%), and high-weight PAHs (5.9%). Combustion-related PAHs during burning periods were 1.54–2.57 times higher than those during nonburning periods. The results of principal component analysis (PCA)/absolute principal component scores (APCS) suggest that the primary pollution sources at the two sites are similar and include vehicle exhaust, coal/wood combustion, incense burning, and incineration emissions. Open burning of rice straw was estimated to contribute approximately 5.0–33.5% to the total atmospheric PAHs at the two sites.     

Simultaneous determination of gaseous and particulate chlorinated polycyclic aromatic hydrocarbons in emissions from the scorching of polyvinylidene chloride film

An analytical method for the determination of gaseous and particulate chlorinated polycyclic aromatic hydrocarbons (ClPAHs) was investigated. By means of this method, concentrations and isomer profiles of the 27 target ClPAHs could be analyzed. To evaluate the usefulness of the method for analyzing ClPAH emissions, laboratory-scale scorching tests were performed on polyvinylidene chloride (PVDC) plastic wrap over a flame of the gas burner. Only seven of the target ClPAHs were detected, and all compounds detected had 2, 3, or 4 rings. The detected ClPAHs were present in both the particulate phase and the gaseous phase, but they were present at higher concentrations in the gaseous phase than in the particulate phase. Relationships between the number of chlorine substituents on the naphthalene/phenanthrene rings and the overall concentration and the percentage in the particulate phase were also investigated.     

Simultaneous determination of gaseous and particulate chlorinated polycyclic aromatic hydrocarbons in emissions from the scorching of polyvinylidene chloride film

An analytical method for the determination of gaseous and particulate chlorinated polycyclic aromatic hydrocarbons (ClPAHs) was investigated. By means of this method, concentrations and isomer profiles of the 27 target ClPAHs could be analyzed. To evaluate the usefulness of the method for analyzing ClPAH emissions, laboratory-scale scorching tests were performed on polyvinylidene chloride (PVDC) plastic wrap over a flame of the gas burner. Only seven of the target ClPAHs were detected, and all compounds detected had 2, 3, or 4 rings. The detected ClPAHs were present in both the particulate phase and the gaseous phase, but they were present at higher concentrations in the gaseous phase than in the particulate phase. Relationships between the number of chlorine substituents on the naphthalene/phenanthrene rings and the overall concentration and the percentage in the particulate phase were also investigated.     

Atmospheric polycyclic aromatic hydrocarbons (PAHs) in Asia: a review from 1999 to 2004

Polycyclic aromatic hydrocarbons (PAHs) are present in both gaseous and particulate phases. These compounds are considered to be atmospheric contaminants and are human carcinogens. Many studies have monitored atmospheric particulate and gaseous phases of PAH in Asia over the past 5 years. This work compares and discusses different sample collection, pretreatment and analytical methods. The main PAH sources are traffic exhausts (AcPy, FL, Flu, PA, Pyr, CHR, BeP) and industrial emissions (BaP, BaA, PER, BeP, COR, CYC). PAH concentrations are highest in areas of traffic, followed by the urban sites, and lowest in rural sites. Meteorological conditions, such as temperature, wind speed and humidity, strongly affect PAH concentrations at all sampling sites. This work elucidates the characteristics, sources and distribution, and the healthy impacts of atmospheric PAH species in Asia.     

Characterisation of PM10 emissions from woodstove combustion of common woods grown in Portugal

A series of source tests was performed to evaluate the chemical composition of particle emissions from the woodstove combustion of four prevalent Portuguese species of woods: Pinus pinaster (maritime pine), Eucalyptus globulus (eucalyptus), Quercus suber (cork oak) and Acacia longifolia (golden wattle). Analyses included water-soluble ions, metals, radionuclides, organic and elemental carbon (OC and EC), humic-like substances (HULIS), cellulose and approximately l80 organic compounds. Particle (PM₁₀) emission factors from eucalyptus and oak were higher than those from pine and acacia. The carbonaceous matter represented 44–63% of the particulate mass emitted during the combustion process, regardless of species burned. The major organic components of smoke particles, for all the wood species studied, with the exception of the golden wattle (0.07–1.9% w/w), were anhydrosugars (0.2–17% w/w). Conflicting with what was expected, only small amounts of cellulose were found in wood smoke. As for HULIS, average particle mass concentrations ranged from 1.5% to 3.0%. The golden wattle wood smoke presented much higher concentrations of ions and metal species than the emissions from the other wood types. The results of the analysis of radionuclides revealed that the ²²⁶Ra was the naturally occurring radionuclide more enriched in PM₁₀. The chromatographically resolved organics included n-alkanes, n-alkenes, PAH, oxygenated PAH, n-alkanals, ketones, n-alkanols, terpenoids, triterpenoids, phenolic compounds, phytosterols, alcohols, n-alkanoic acids, n-di-acids, unsaturated acids and alkyl ester acids.     

Chemical characterization and source identification of polycyclic aromatic hydrocarbons in aerosols originating from different sources

To obtain the characteristic factors or signatures of particulate polycyclic aromatic hydrocarbons (PAHs) to help identify the sources of particulate PAHs in the atmosphere, different carbonaceous aerosols were generated by burning different fossil fuels and biomass under different conditions in the laboratory, and the chemical characteristics of 14 PAHs were studied in detail. The results showed that (1) carbonaceous aerosols derived from domestic burning of coal, diesel fuel, and gasoline have much higher concentrations of PAHs than those derived from domestic burning of biomass; (2) carbonaceous aerosols derived from domestic burning of diesel fuel/gasoline have similar PAH components as those derived from high-temperature combustion of diesel fuel/gasoline, although the former have much higher concentrations of PAHs than the latter, suggesting that the burning temperature obviously affects the emitting amount of particulate PAHs, but only slightly influences the PAHs components; and (3) the ratios of benzo[b]fluoranthene/acenaphthylene, benzo[b]fluoranthene/fluorene, dibenzo[a,h]anthracene/acenaphthylene, dibenzo[a,h]anthracene/fluorine, and benzo[b]fluoranthene/benzo[k]fluoranthene in carbonaceous aerosols are sensitively dependent on their sources, indicating that these ratios are suitable for use as characteristic factors or signatures of particulate PAHs in the atmosphere.     

A Comprehensive Strategy to Reduce Residential Wood Burning Impacts in Small Urban Communities

Paniculate control strategies in the U.S. have historically focused on the reduction of industrial emissions. In recent years, however, area sources such as residential wood combustion have been recognized as significant and rapidly increasing sources of particulate emissions. In some areas of the country it will be necessary to substantially reduce residential wood burning emissions in order to attain or maintain acceptable levels of total and respirable particulate matter. A comprehensive strategy to reduce residential wood burning impacts has been developed for the Medford-Ashland area, 1 a community of about 100,000 population situated in a poorly ventilated valley in Oregon. Portions of this strategy will be applied in other areas of Oregon. The strategy may be applicable to urban communities in other states as well.     

Emissions of polycyclic aromatic hydrocarbons (PAHs) and nitro-PAHs from heavy-duty diesel vehicles with DPF and SCR

In total, 24 polycyclic aromatic hydrocarbons (PAHs) in both gas and particle phases and 35 nitro-PAHs in particle phase were analyzed in the exhaust from heavy-duty diesel vehicles equipped with after-treatment for particulate matter (PM) and NO_X control. The test vehicles were carried out using a chassis dynamometer under highway cruise, transient Urban Dynamometer Driving Schedule (UDDS), and idle operation. The after-treatment efficiently abated more than 90% of the total PAHs. Indeed, the particle-bound PAHs were reduced by >99%, and the gaseous PAHs were removed at various extents depending on the type of after-treatment and the test cycles. The PAHs in gas phase dominated the total PAH (gas + particle phases) emissions for all the test vehicles and for all cycles; that is, 99% of the two-ring and 98% of the three-ring and 97% of the four-ring and 95% of the carcinogenic PAHs were in the gas-phase after a diesel particle filter (DPF) and not bound to the very small amount of particulate matter left after a DPF. Consequently, an evaluation of the toxicity of DPF exhaust must include this volatile fraction and cannot be based on the particle fraction only. The selective catalytic reduction (SCR) did not appear to promote nitration of the PAHs in general, although there might be some selective nitration of phenanthrene. Importantly the after-treatmtent reduced the equivalent B[a]P (B[a]Peq) emissions by >95%, suggesting a substantial health benefit.

Implications: This study demonstrated that after-treatments, including diesel particulate filters (DPF), diesel oxidation catalysts (DOC), and selective catalytic reduction (SCR), significantly reduce the emissions of PAHs from heavy-duty diesel engines. The gas-phase PAHs dominate the total PAH (gas + particle phases) emissions from heavy-duty diesel vehicles retrofitted with various DPFs and not bound to the very small amount of particulate matter left after a DPF. Consequently, an evaluation of the toxicity of DPF exhaust must also include this volatile fraction and cannot be based on the particle fraction only.

Supplemental Materials: Supplemental materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association.     

Wood smoke as a source of particle-phase organic compounds in residential areas

The objective of this study was to investigate the organic composition of wood smoke emissions and ambient air samples in order to determine the wood smoke contribution to the ambient air pollution in the residential areas. From November 2005 to March 2006 particle-phase PM₁₀ samples were collected in the residential town Dettenhausen surrounded by forests near Stuttgart in southern Germany. Samples collected on pre-baked glass fibre filters were extracted using toluene with ultrasonic bath and analysed by gas chromatography mass spectrometry (GC-MS). 21 polycyclic aromatic hydrocarbons (PAH) including 16 USEPA priority pollutants, different organic wood smoke tracers, primarily 21 species of syringol and guaiacol derivatives, levoglucosan and its isomers mannosan, galactosan and dehydroabietic acid were detected and quantified in this study. The concentrations of these compounds were compared with the fingerprints of emissions from hardwood and softwood combustion carried out in test facilities at Universitaet Stuttgart and field investigations at a wood stove during real operation in Dettenhausen. It was observed that the combustion derived PAH was detected in higher concentrations than other PAH in the ambient air PM₁₀ samples. Syringol and its derivatives were found in large amounts in hardwood burning but were not detected in softwood burning emissions. On the other hand, guaiacol and its derivatives were found in both softwood and hardwood burning emissions, but the concentrations were higher in the softwood smoke compared to hardwood smoke. So, these compounds can be used as typical tracer compounds for the different types of wood burning emissions. In ambient air samples both syringol and guaiacol derivatives were found which indicates the wood combustion contribution to the PM load in such residential areas. Levoglucosan was detected in high concentrations in all ambient PM₁₀ samples. A source apportionment modelling, Positive Matrix Factorization (PMF) was implemented to quantify the wood smoke contribution to the ambient PM₁₀ bound organic compounds in the residential area.     

Chemical and biological characterization of emissions from small residential stoves burning wood and charcoal

Emissions from a small residential wood stove and a newly developed residential stove burning charcoal have been characterized by chemical analysis and mutagenicity testing (Ames Salmonella test). For wood burning the samples were taken under normal and starved air conditions burning birch and spruce separately. The burning conditions in the stove seemed to influence the emissions to a larger extent than the type of wood.The emissions of aldehydes, benzene and polycyclic aromatic hydrocarbons from the charcoal-burning stove are lower by a factor of 25–1000 as compared to the wood stove. The mutagenicity of the emissions showed a similar trend.     

Exposure of traffic police to Polycyclic aromatic hydrocarbons in Beijing, China

Exposure of on-duty traffic police in Beijing to polycyclic aromatic hydrocarbons (PAHs) was investigated during the summer, 2004 using a personal sampling technique in measuring both particulate and gaseous phase PAHs. The results were then compared with those from two control sites away from the street. Exposure levels to gaseous and particulate PAHs for the traffic police were found to be 1525 +/- 759 ngm(-3) and 148 +/- 118 ngm(-3), respectively, representing 2-2.5 times higher levels than those at the control sites. The daily inhalation exposure of the police was estimated to be 277 ngkg(-1)d(-1). Most of the PAHs exposure came from the vapor phase, particularly NAP, FLO and PHE. Based on calculated PAH diagnostic ratios, the major source of PAHs exposure was from vehicle exhaust. The effects of temperature, humidity and atmospheric stability on exposure levels are also discussed.     

蜂窝煤燃烧烟气中多环芳烃的定量研究及粒径分布特征

通过对蜂窝煤燃烧排放的烟气中多环芳烃的定量分析,研究了17种多环芳烃在烟气颗粒相和气相中的分配以及在不同粒径颗粒物上的分布特征。结果表明：在室温下燃煤排放的多环芳烃总量以在气相中存在为主,但总体毒性则主要存在于颗粒相中;多环芳烃主要分布在亚微米级颗粒上,分子量越大的多环芳烃越趋于富集在细颗粒上,因而对健康的危害就越大。