Ultrasensitive determination of carbendazim in water and orange juice using a carbon paste electrode

A carbon paste electrode was used for the electrochemical quantification of carbendazim in water and orange juice samples. Carbendazim oxidation on the electrode surface was found to be controlled by adsorption. The novel electrochemical procedure for carbendazim quantification employed differential pulse voltammetry using a carbon paste electrode under optimal conditions. Carbendazim oxidation currents were linear at concentrations of 2.84 to 45.44 µg L^?1, with a limit of detection of 0.96 µg L^?1. The proposed method was applied to carbendazim quantification in ultrapurified water, river water, and orange juice. Recovery rates in water and orange juice samples were in the 97%–101% range, indicating that the method can be employed to determine carbendazim in these matrices, with advantages including shorter analysis time and lower cost than routine methods such as chromatography or spectroscopy. The electrode showed good reproducibility, remarkable stability, and especially good surface renewability by simple mechanical polishing. The recovery rates observed were highly concordant with those obtained for high-performance liquid chromatography, having a relative standard deviation of less than 1.3%.     

Highly sensitive and selective determination of malathion in vegetable extracts by an electrochemical sensor based on Cu-metal organic framework

Abstract

This article demonstrates the first application of a copper-based porous coordination polymer (BTCA-P-Cu-CP) as a carbon paste electrode (CPE) modifier for the detection of malathion. The electrochemical behavior of BTCA-P-Cu-CP/CPE was explored using cyclic voltammetry (CV) while chrono-amperometry methods were applied for the analytical evaluation of the sensor performance. Under optimized conditions, the developed sensor exhibited high reproducibility, stability, and wide dynamic range (0.6–24?nM) with the limits of detection and sensitivity equal to 0.17?nM and 5.7 µAnMcm^?1, respectively, based on inhibition signal measurement. Furthermore, the presence of common coexisting interfering species showed a minor change in signals (<4.4%). The developed sensor has been applied in the determination of malathion in spiked vegetable extracts. It exhibited promising results in term of fast and sensitive determination of malathion in real samples at trace level with recoveries of 91.0 to 104.4%. (RSDs < 5%, n?=?3). A comparison of the two studied techniques showed that the HPLC technique is unable to detect malathion when the concentration is lower than 1.8?µM while 0.006 µM is detected with appropriate RSDs 0.2–5.2% (n?=?3) by amperometric method. Due to the high sensitivity and selectivity, this new electrochemical sensor will be useful for monitoring trace malathion in real samples.     

化学修饰碳糊电极测定废水中痕量铜

研制了732型阳离子交换树脂碳糊修饰电极,在盐酸－乙二胺体系中,对Cu（Ⅱ）显示出良好的离子交换和选择性,电极具有很好的重现性和较长的使用寿命,可用于废水中痕量铜的测定。     

平板炭气凝胶电极电吸附除氟

采用自制的炭气凝胶平板电极进行模拟水样中氟的电吸附去除研究,通过单因子实验优化了该电吸附技术的操作参数和适用的溶液条件,并研究了反接电极法的再生效果。研究结果表明,自制的炭气凝胶平板由纳米颗粒组成三维网络结构,比表面积为670.90 m2/g,具有良好的充放电可逆性和迅速形成表面双电层的特点。静态电吸附除氟效果最佳的条件为:水样氟离子浓度6 mg/L,pH 7.0,极板间距4 cm,电压1.6 V;共存物质硝酸根、腐殖酸、碳酸根和碳酸氢根等对氟离子的电吸附具有一定的促进作用。吸附氟离子后的炭气凝胶材料的比表面、孔体积、电容值有所减小。对于吸附氟离子后的炭气凝胶平板电极,采用反接电极法取得较好再生效果的条件为:流动状态、电压1.6 V、极板间距4 cm。再生后的炭气凝胶电极与原始炭气凝胶相比,依然具有良好的充放电可逆性。     

Immobilized-cell-augmented activated sludge process for treating wastewater containing hazardous compounds.

A novel bioaugmentation scheme called immobilized-cell-augmented activated sludge (ICAAS) was developed. Offline enricher reactors were used to maintain immobilized acclimated cells applied to augment completely mixed activated sludge (CMAS) treating a pentachlorophenol (PCP) pulse loading. Cellulose triacetate (CA) and powder activated carbon (PAC) combined with CA (PAC + CA) were the two media types used for entrapping the PCP-degrading culture. With ICAAS at 5% by volume augmentation, PCP removal of 73.1 and 75.1% via biodegradation, volatilization, and adsorption onto suspended cells, entrapped cells, and media was achieved for the systems with CA and PAC + CA media, respectively, while PCP removal in a control CMAS, which had a comparable level of combined PCP adsorption onto suspended cells and volatilization as the ICAAS, was 48.7%. Results further showed that the immobilized cells retained their PCP-degrading ability when they were fed with the inducer (PCP) once every 20 days.     

A new strategy for determination of hydroxylamine and phenol in water and waste water samples using modified nanosensor

A carbon paste electrode modified with p-chloranil and carbon nanotubes was used for the sensitive and selective voltammetric determination of hydroxylamine (HX) and phenol (PL). The oxidation of HX at the modified electrode was investigated by cyclic voltammetry (CV), chronoamperommetry, and electrochemical impedance spectroscopy. The values of the catalytic rate constant (k), and diffusion coefficient (D) for HX were calculated. Square wave voltammetric peaks current of HX and PL increased linearly with their concentrations at the ranges of 0.1–172.0 and 5.0–512.0 μmol L^?1, respectively. The detection limits for HX and PL were 0.08 and 2.0 μmol L^?1, respectively. The separation of the anodic peak potentials of HX and PL reached to 0.65 V, using square wave voltammetry. The proposed sensor was successfully applied for the determination of HX and PL in water and wastewater samples.     

催化臭氧氧化处理对氯苯酚的研究

采用臭氧氧化法处理对氯苯酚溶液,研究了pH、温度、气体流量和对氯苯酚初始浓度等因素对处理效果的影响.反应体系pH越高,越有利于氧化反应.用自制的载有Fe,Co,Mn氧化物的活性炭纤维(ACF)催化剂进行催化臭氧氧化对氯苯酚的实验.结果表明,Fe/ACF显示了较好的催化性能和活性.通过在反应体系中加入一定量的羟基自由基猝灭剂,初步探讨了其催化机理,即催化剂和臭氧反应生成了氧化性极强的羟基自由基.     

An electrochemical nanocomposite modified carbon paste electrode as a sensor for simultaneous determination of hydrazine and phenol in water and wastewater samples

In this study, we report preparation of a high sensitive electrochemical sensor for determination of hydrazine in the presence of phenol in water and wastewater samples. In the first step, we describe synthesis and characterization of ZnO/CNTs nanocomposite with different methods such as transmission electron microscopy (TEM) and X-ray diffraction (XRD). In the second step, application of the synthesis nanocomposite describes the preparation of carbon paste electrode modified with n-(4-hydroxyphenyl)-3,5-dinitrobenzamide as a high sensitive and selective voltammetric sensor for determination of hydrazine and phenol in water and wastewater samples. The mediated oxidation of hydrazine at the modified electrode was investigated by cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy (EIS). Also, the values of catalytic rate constant (k) and diffusion coefficient (D) for hydrazine were calculated. Square wave voltammetry (SWV) of hydrazine at the modified electrode exhibited two linear dynamic ranges with a detection limit (3σ) of 8.0 nmol L^?1. SWV was used for simultaneous determination of hydrazine and phenol at the modified electrode and quantitation of hydrazine and phenol in some real samples by the standard addition method.     

Formation and emission of chloroanisoles as indoor pollutants

GOAL, SCOPE AND BACKGROUND: Complaints by residents of frame-houses about musty odour in the houses has become an increasing problem within the last years. An additional problem is that the odour is transferred to clothes and skin. The persons themselves do not recognize the smell after a while because of adaptation. Serious social problems are the result. For a long time, the smell was explained to be from mould due to construction-based humidity problems. However, in an increasing number of houses, no indications were found for elevated levels of mould growth. METHODS: Air and material samples were taken from 5 houses, which show typical musty odours, and analysed with respect to chlorophenols and chloroanisoles. Additionally, some samples were analysed for lindane and its metabolites, because lindane was commonly used together with pentachlorophenol (PCP) for wood protection. RESULTS AND DISCUSSION: Meticulous analysis resulted in the identification of chloroanisoles, mainly 2,3,4,6-tetrachloroanisole. These substances are known from corky wines and from contamination of food from pentachlorophenol (PCP) treated pallets and result from microbiological metabolic processes. Pentachlorophenol was commonly used to protect wood from fungi in Germany mainly in the later 60s and 70s. Details of these processes, as well as effective methods to identify chloroanisoles in the problem houses, are described. CONCLUSIONS: Chloroanisoles formed by metabolism of PCP have been well known to contaminate food or wine. Here, they were identified and are probably responsible for the musty odours in the frame houses. Since it is quite clear that these substances were not components of building materials used in the houses, an explanation for chloroanisole formation is proposed. Localized dampness probably favours microbial growth associated with metabolic conversion of chlorophenols to the corresponding chloroanisoles, primarily 2,3,4,6-tetrachloroanisol, which spread throughout the buildings, resulting in the observed odours. RECOMMENDATIONS AND OUTLOOK: The group of chloroanisoles has been recognized as important indoor pollutants as they possess musty odours at extremely low concentrations, e.g. for 2,4,6-trichloroanisole in a range of 5-10 ppt in air (Staples 2000). On the basis of currently available toxicological data, exposure of the occupants to the concentrations of chloroanisoles measured is not associated with a health risk. No correlation could be observed between concentrations of chloroanisoles and PCP in house dust and indoor air. However, chloroanisoles are good indicators for possible PCP-treatment of wood in frame houses and their detection should initiate investigations on PCP contamination. Research is continuing to identify the microorganisms involved and to devise a remediation procedure for affected houses.     

Degradation of pentachlorophenol by pure and mixed cultures in two different soils

GOAL, SCOPE AND BACKGROUND: Pentachlorophenol (PCP) is the second highest volume pesticide used in the United States. It is a mutagenic compound whose exposure poses significant health effects, One of the most desirable, environmentally friendly treatment methods is bioremediation. For soil-based contamination, the effectiveness of bioremediation will also be affected by the presence of an active indigenous population, sorption of the contaminant onto the soil, and environmental parameters. METHODS: Two pure strains and their mixed culture were used to evaluate PCP biodegradation in two different field soils, Columbia (CO) and New Mexico (NM). Biostimulation of the indigenous microbes was evaluated by adding nutrients. The efficiency of adding bacteria strains (bioaugmentation) for degrading PCP was determined with Arthrobacter sp., Flavobacterium sp. and a 50:50 mixture of the two bacteria strains. RESULTS: In CO soil, only 24%, 12% and 25% of the initial PCP concentration were degraded by Flavobacterium sp., Arthrobacter sp. and mixed culture, respectively. Arthrobacter sp. was used in NM soil with two initial concentrations and achieved degradation efficiencies of 57% and 61% for 361 and 95 mg kg- concentrations, respectively. Discussion. Analysis via statistical methods showed that the bacteria had different efficiencies on PCP degradation in each soil. 2 CONCLUSIONS: All bacteria catalyzed a higher PCP degradation when present in NM soil. Second, Flavobacterium sp. degraded more PCP than Arthrobacter sp. in CO soil. The mixed culture achieved the highest degradation efficiency regardless of the initial concentration or soil origin. RECOMMENDATIONS AND PERSPECTIVES: The effect of the soil properties, such as the soil organic matter (SOM) on PCP biodegradation should be investigated. Future work can also investigate the effect of aging time on biodegradation.     

Bioremediation of soil contaminated with pentachlorophenol (PCP) using humic acids bound on zeolite

We determined the toxicity of various chlorophenols, especially pentachlorophenol (PCP), on five bacterial strains and studied PCP biodegradation in soils amended with an organomineral complex (OMC) prepared from humic acids (organic part) bound on zeolite (inorganic part). Both components of OMC have excellent sorption properties and are of natural origin and therefore suitable to be used in the environment. Toxicity of chlorophenols depends not only on the number of chlorine atoms but also on their position on aromatic ring, and is thus regiospecific. Biodegradation of PCP was studied in three real completely characterized soil samples, Chernozem, Fluvisol, and Regosol, with and without the addition of OMC. The soils were sterilized and bioaugmented with the bacterial isolate Comamonas testosteroni CCM 7530. The immobilization effect of OMC in relation to PCP depends on the concentration of humic acids (HAs), the PCP concentration, and the content of organic carbon in soil. The microbial activity and the simulated action of acid rains led to the gradual release and biodegradation of the reversibly bound PCP without no initial toxic effect on indigenous or bioaugmented microorganisms. OMC appeared to be a good trap for PCP with potential applications in remediation technology because it reduces the potential toxicity of PCP to microbial community by lowering its bioavailability and thus facilitates its biodegradation.     

A kinetic study on oxidation of pentachlorophenol by ozone

The kinetics of pentachlorophenol (PCP) ozonation in terms of the gaseous O3 and dissolved PCP concentrations has been investigated. When the O3 concentration in the gas phase was in the range of 10 to 40 g O3/m3, the O3 dissolved for a short time period was proportional to the gaseous O3 concentration. In this range, the ozonation reaction was first order for each reactant and the overall reaction was second order. At 25 degrees C, in an aqueous solution, the reaction rate constant was estimated to be 10.048 L/mol.sec. The reaction rate was much greater than the mass-transfer rate, indicating that the reaction of O3 and PCP was an interface reaction on the surface of gaseous O3 bubbles. The final product of the PCP ozonation was oxalic acid, with the carbon yield of the reaction being 59.4%. The ozonation of PCP in the aqueous solution was not a radical reaction but a direct reaction between O3 and PCP molecules under the conditions investigated in this study, since O3 has a high selectivity toward PCP. The reaction rate increased with the reaction temperature up to 35 degrees C but decreased at temperatures greater than 35 degrees C due to the decreased solubility of O3. The addition of H2O2 did not increase the reaction rate significantly.     

Photodegradation of pentachlorophenol by sunlight in aquatic surface microlayers

Photodegradation of pentachlorophenol (PCP) in aquatic surface microlayer (SM) was examined under natural sunlight. SM samples were collected using a glass plate, along with corresponding subsurface waters. PCP was added to samples of the SM and subsurface water. When all samples were exposed to the same natural sunlight conditions, the first order photodegradation rates of PCP in the SM water samples were different from those of PCP in corresponding subsurface water samples. The difference was correlated with the enrichment of dissolved organic carbon (DOC) in SM compared to the corresponding subsurface waters. Enhanced photodegradation in SM may be due to increased abundance of photoreactants related to the UV-absorbing properties of dissolved organic materials in the SM as the result of photo-induced reactions. Effects of environmental factors, pH and salinity, on photodegradation process of PCP in SM were also evaluated.     

Adsorption behavior of 2,4-dichlorophenol and pentachlorophenol in an allophanic soil

The adsorption of 2,4-dichlorophenol (2,4-DCP) and pentachlorophenol (PCP) by a variable-charge soil from southern Chile was studied in a series of batch equilibration experiments. 2,4-DCP and PCP adsorption behavior was evaluated as a function of pH (pH values of 4.5, 6.0 and 7.5) in a 0.1M KCl (25 degrees C) background solution for soil material collected at three different depths (0-20 cm, 20-40 cm, and 40-60 cm). 2,4-DCP and PCP adsorption decreased with increasing soil pH, suggesting that the undissociated species were adsorbed more readily and that electrostatic repulsion may inhibit partitioning as pH increases. The PCP adsorption was greater than observed for 2,4-DCP and decreased with soil depth. Multiple regression analysis between K(d) and various soil properties indicated that the soil organic carbon content is a strong indicator of chlorophenol adsorption, and in addition to organic carbon, the soil pH is an important property controlling adsorption behavior.     

Simultaneous removal of nitrate and pentachlorophenol from simulated groundwater using a biodenitrification reactor packed with corncob

Both nitrate and pentachlorophenol (PCP) are familiar pollutants in aqueous environment. This research is focused on the simultaneous removal of nitrate and PCP from simulated contaminated groundwater using a laboratory-scale denitrification reactor packed with corncob as both carbon source and biofilm support. The reactor could be started up readily, and the removal efficiencies of nitrate and PCP reached up to approximately 98 % and 40–45 % when their initial concentrations were 50 mg N/L and 5 mg/L, respectively, after 15-day continuous operation at 10 h of hydraulic retention time (HRT) and 25 °C. Approximately 91 % of PCP removal efficiency was achieved, with 2.47 mg/L of chloride ion release at 24 h of HRT. Eighty-two percent of chlorine in PCP removed was ionized. The productions of 3-chlorophenol and phenol and chloride ion release indicate that the reductive dechlorination reaction is a major degradation pathway of PCP under the experimental conditions.     

Microbial activities in soils of a former sawmill area

To find out microbial metabolic functioning and toxicity in a former sawmill area, carbon dioxide evolution, methane oxidation potential, 10 hydrolytic enzyme activities, Vibrio fischeri test, fluorescein diacetate hydrolysis activity (FDA), soil pH, carbon, nitrogen and pentachlorophenol (PCP) content were measured at four sites. The area is contaminated with aged chlorophenols. Chlorophenol content of soil was analyzed with a novel HPLC-MS technique, which allowed to measure chlorophenols without derivatization. The sites had a pollution gradient from 0.5 to 15 microg PCP g dw of soil(-1). Endogenous carbon dioxide evolution, methane oxidation potential, butyrate-esterase, acetate-esterase, sulphatase and aminopeptidase activities were lower at the site 2 than 3, although the site 2 and 3 had similar content of carbon and nitrogen. The soil was toxic in V. fischeri test at the site 2, which had high content of PCP (3.93+/-1.00 microg PCP g dw of soil(-1)). The results indicated that endogenous carbon dioxide evolution, methane oxidation potential, butyrate-esterase, acetate-esterase, sulphatase and aminopeptidase activities were sensitive to PCP in the soil. The results indicated that alpha-glucosidase, beta-glucosidase, beta-xylosidase, beta-cellobiosidase, phosphomonoesterase, N-acetyl-glucosaminidase activity and FDA hydrolysis activity were not sensitive to PCP in the soil. Soil processes involved in the cycling of carbon, nitrogen, sulphur and phosphorus were only slightly vulnerable in the former sawmill area and most sensitive microbial species were probably replaced with more tolerant ones to maintain and recover functioning of the former sawmill soils.     

Nanocellulosic fiber-modified carbon paste electrode for ultra trace determination of Cd (II) and Pb (II) in aqueous solution

In recent years, increasing awareness of the environmental impact of heavy metals has prompted a demand for monitoring and decontaminating industrial wastes prior to discharging into natural water bodies. This paper describes the preparation and electrochemical application of carbon paste electrode modified with nanocellulosic fibers for the determination of cadmium and lead in water samples using anodic stripping voltammetry. First, cadmium and lead were adsorbed on the carbon paste electrode surface at open circuit potential, followed by anodic stripping voltammetric scan from -1 to 0 V. Different factors affecting sensitivity and precision of the electrode, including accumulating solvent, pH of the accumulating solvent, accumulation time, supporting electrolyte, and scan rate were investigated. The proposed method was also applied to the determination of Cd (II) and Pb (II) in the presence of other interfering metal ions and cetyl trimethyl ammonium bromide, sodium dodecyl sulfate, and Triton X-100 as a representative of cationic, anionic, and neutral surfactants. Linear calibration curves were obtained in the concentration ranges of 150–650 μg?L^?1 and 80–300 μg?L^?1, respectively, for cadmium and lead at an accumulated time of 10 min with limits of detection 88 and 33 μg?L^?1. Optimized working conditions are defined as acetate buffer of pH?5 as accumulating solvent, hydrochloric acid as supporting electrolyte, and scan rate 50 mV/s. This technique does not use mercury and therefore has a positive environmental benefit. The method is reasonably sensitive and selective and has been successfully applied to the determination of trace amounts of Cd (II) and Pb (II) in water samples.     

Photoelectrocatalytic degradation of pentachlorophenol in aqueous solution using a TiO2 nanotube film electrode

Titanium dioxide (TiO2) nanotube film electrodes are fabricated by the anodic oxidation method. Scanning electron microscopy (SEM) showed that these tubes were well aligned and organized into high-density uniform arrays. XRD analysis showed the TiO2 nanotubes to be in the anatase crystal form. The TiO2 nanotube film electrode exhibited increased photoelectrocatalytic (PEC) capability compared to a traditional TiO2 film electrode fabricated using the anodizing method for pentachlorophenol (PCP) degradation in aqueous solution. The bias potential, pH value, and electrolyte concentration were shown to be important factors influencing the degradation of PCP by the PEC method using the TiO2 nanotube film electrode as the working electrode.     

Porous organoclay composite for the sorption of polycyclic aromatic hydrocarbons and pentachlorophenol from groundwater

Complex mixtures of hazardous chemicals such as polycyclic aromatic hydrocarbons (PAHs) in contaminated soil and groundwater can have severe and long-lasting effects on health. The evidence that these contaminants can cause adverse health effects in animals and humans is rapidly expanding. The frequent and wide-spread occurrence of PAHs in groundwater makes appropriate intervention strategies for their remediation highly desirable. The core objective of this research was to assess the ability of a clay-based composite to sorb and remove toxic contaminants from groundwater at a wood-preserving chemical waste site. Treatment efficiencies were evaluated using either effluent from an oil-water separator (OWS) or a bioreactor (B2). The effluent water from these units was passed through fixed bed columns containing either an organoclay composite or granular activated carbon. The sorbent columns were placed in-line using existing sampling ports at the effluent of the OWS or B2. Individual one-liter samples of treated and untreated effluent were collected in Kimax bottles over the course of 78 h (total of 50 samples). Subsequently each sample was extracted by solid phase extraction methodology, and pentachlorophenol (PCP) and PAH concentrations were quantitated via GC/MS. Columns containing porous organoclay composite, i.e. sand-immobilized cetylpyridinium-exchanged low-pH montmorillonite clay (CP/LPHM), were shown to reduce the contaminant load from the OWS effluent stream by 97%. The concentrations of benzo[a]pyrene (BaP) and PCP were considerably reduced (i.e. >99%). An effluent stream from the bioreactor was also filtered through columns packed with composite or an equivalent amount of GAC. Although the composite reduced the majority of contaminants (including BaP and PCP), it was less effective in diminishing the levels of lower ring versus higher ring PAHs. Conversely, GAC was more effective in removing the lower ring PAHs, except for naphthalene and PCP. The effectiveness of sorption of PCP from the OWS effluent by the composite was confirmed using a PCP-sensitive adult hydra bioassay previously described in our laboratory. The findings of this initial study have delineated differences between CP/LPHM and GAC for groundwater remediation, and suggest that GAC (instead of sand) as the solid support for organoclay may be more effective for the treatment of contaminated groundwater under field conditions than GAC or CP/LPHM alone. Further work is ongoing to confirm this conclusion.     

Dechlorination and destruction of 2,4,6-trichlorophenol and pentachlorophenol using hydrogen peroxide as the oxidant catalyzed by molybdate ions under basic condition

The dechlorination and destruction of 2,4,6-trichlorophenol (TCP) and pentachlorophenol (PCP) under basic condition using hydrogen peroxide as the oxidant catalyzed by molybdate ions have been studied. Under ambient conditions of temperature and pressure, more than 95% of millimolar solutions of TCP and PCP can be converted to CO2 and CO, chlorinated and nonchlorinated carboxylic acid in 40 min. Up to 2.4 chloride ions per TCP and 3.5 chloride ions per PCP were released. TOC measurements indicated that 18% and 11% of the carbon was mineralized for TCP and PCP respectively after an hour of reaction. The results of ESR measurements suggested that the reaction possibly proceeded via the pathway with singlet oxygen.