共查询到20条相似文献,搜索用时 0 毫秒
1.
市政污泥(简称污泥)厌氧发酵产氢既可解决污泥的出路问题,又能产生清洁能源--氢气,是一种较为理想的处理处置方式。调节污泥适合的初始pH值能够提高污泥的产氢效率。为了考察不同初始pH值对污泥厌氧发酵产氢的影响,将未经任何预处理污泥(原污泥)的初始pH分别调到2.0~12.0,用于批式实验。研究表明:调节原污泥初始pH,适当条件下能促进氢气的生成。初始pH为强酸性条件时,污泥基本不产氢;初始pH在4.0~11.0,污泥总体产氢量也很低;初始pH=12.0条件下,污泥总体产氢量最高,比产氢率达到3.39 mL·(g VS)-1。不同初始pH下污泥的降解均以蛋白质降解为主。酸性条件下,蛋白质及糖类物质有一定降解;中性条件下,蛋白质及糖类物质都得到较好的降解,浓度均较低;碱性条件下,糖类物质的酸化较微弱,但蛋白质却得到较好的降解,降解蛋白质生成的TVFA由于甲烷菌受到抑制而产生积累。 相似文献
2.
曝气生物活性炭滤池深度处理高浓度氨氮原水 总被引:3,自引:0,他引:3
实验研究曝气生物活性炭滤池对于高浓度氨氮原水的处理效果以及工艺运行稳定情况。以某自来水厂常规工艺沉淀池出水预加硫酸铵作为研究对象,原水氨氮平均浓度3.67 mg/L,实验条件:温度31.2℃,pH 7.13,滤速8~12 m/h,气水比0.5和1。采用3种不同工况条件进行实验,确定滤速10 m/h和气水比0.5的为最佳运行工况。在此工况下曝气生物活性炭滤池对于氨氮和COD Mn的平均去除率分别达到87.5%和19.2%,亚硝酸盐积累率为0.9%;出水氨氮浓度达到生活饮用水卫生标准GB5749-2006。同时炭滤池的出水浊度相比进水略微上升。 相似文献
3.
4.
以污泥为载体的金属氧化物脱硝催化剂的研究 总被引:2,自引:3,他引:2
以城市污水处理厂剩余污泥为原料,用氯化锌、硝酸锰和硝酸铁化学浸渍、高温热解制备脱除NO的催化剂.用微型气固相催化反应装置考察了该催化剂在CO选择性催化还原NO中的应用效果及寿命.实验结果表明:在350~550℃时的催化活性较高,在450℃时NO的最大转化率可达97.1%;催化剂的活性良好,经660 min的活性测试,催化剂的活性只降低了约3%.对该催化剂进行了BET、X射线衍射和扫描电镜分析,结果表明,该催化剂具有丰富的晶体结构,而且表面及空隙间负载的活性粒子较多,这些特征也表明该催化剂具有良好的催化性能. 相似文献
5.
Akira Sano Makoto KanomataHiroki Inoue Norio SugiuraKai-Qin Xu Yuhei Inamori 《Chemosphere》2012,89(10):1243-1247
The objective of the present study was to establish an alkali extraction technology for FePO4-containing sewage sludge obtained from a wastewater treatment system that includes phosphorous removal by iron electrolysis. By clarifying the extraction properties of phosphorous, organic matter, and inorganic matter, conditions for alkali extraction were optimized. As a result, it was suggested that unheated phosphorous extraction would be superior for FePO4-containing sewage sludge. And, extraction methods and sewage sludge properties were also compared, and the noteworthy result that extraction of metals can be suppressed to extremely low amounts with alkali extraction as compared with acid extraction was obtained. A new insight was also gained that, as compared with the use of incinerated ash reported in previous studies, alkali extraction was more efficient when raw sewage sludge was used. 相似文献
6.
膜污染是制约MBR发展的瓶颈。考察投加ABS颗粒对MBR膜组件上膜泥饼层的影响,并设对照实验。结果表明,对照MBR膜通量下降速度快,膜污染严重,膜表面上累积厚厚的泥饼层,而在ABS MBR中膜通量下降速度则缓慢的多,且膜上泥饼层积累量则明显少于对照MBR;曝气量越大,颗粒运行的速度也越快,泥饼层被撞落量也越多;颗粒以碰撞角度为45°冲刷膜的情况下,泥饼层掉落效果明显增加;泥饼层包裹的膜丝根数越多,泥饼层的静摩擦力和保持泥饼层不被破坏的力也越大,泥饼层就越难被冲刷掉。SEM照片显示,ABS MBR的膜孔堵塞要严重于对照MBR,表面的褶皱要较对照MBR多。 相似文献
7.
8.
Pretreatment of sludge with microwaves for pathogen destruction and improved anaerobic digestion performance. 总被引:6,自引:0,他引:6
Seung M Hong Jae K Park N Teeradej Y O Lee Y K Cho C H Park 《Water environment research》2006,78(1):76-83
A new way of generating Class A sludge using microwaves was evaluated through a series of laboratory-scale experiments. Microwaves provide rapid and uniform heating throughout the material. Other benefits of microwave treatment include instant and accurate control and selective and concentrated heating on materials, such as sludge, that have a high dielectric loss factor. Sludge was irradiated with 2450-MHz microwaves, and fecal coliforms were counted. Fecal coliforms were not detected at 65 degrees C for primary sludge and anaerobic digester sludge and at 85 degrees C for waste activated sludge when sludge was irradiated with 2450-MHz microwaves. During the bench-scale anaerobic digester operation, the highest average log reduction of fecal coliforms was achieved by the anaerobic digester fed with microwave-pretreated sludge (> or = 2.66 log removal). The anaerobic digester fed with microwave-irradiated sludge was more efficient in inactivation of fecal coliforms than the other two digesters fed with raw sludge and externally heated sludge, respectively. It took more than three hydraulic retention times for a bench-scale mesophilic anaerobic digester to meet Class A sludge requirements after feeding microwave-irradiated sludge. Class A sludge can be produced consistently with a continuously fed mesophilic anaerobic digester if sludge is pretreated with microwaves to reach 65 degrees C. 相似文献
9.
活性污泥法处理高钙废水中污泥特性的变化 总被引:3,自引:0,他引:3
通过单级SBR法处理模拟高钙废水,研究了活性污泥法处理高钙废水的过程中钙离子对COD,MLVSS,MLSS,SVI,污泥增长速率,污泥形态结构及生物相的影响,揭示活性污泥法处理高钙废水的过程中污泥量巨大的原因。采用逐步增加钙离子浓度的方法,检测到在污泥培养期([Ca2+]=0 mg/L),COD去除率为98.1%,MLVSS和MLSS稳定在4 900~5 500mg/L,污泥增长速率为67 mg/(L·d),SVI为55~60 mL/g;在驯化处理期([Ca2+]=120~2 400 mg/L),COD去除率降至87.37%,MLVSS降至2 500 mg/L,MLSS增加至19 300 mg/L,污泥增长速率为212.31 mg/(L·d),SVI降至25 mL/g;在冲击期([Ca2+]=4 000 mg/L),COD去除率降至69.23%,MLVSS降至1 600 mg/L,MLSS迅速增加至24 200 mg/L,污泥增长速率为816.67 mg/(L·d),SVI降至14 mL/g。经显微镜观察发现,污泥絮体由松散变得密实,生物相由钟虫等指示性微生物变为不适应环境的胞囊结构。结果表明,随Ca2+浓度的增加,COD去除率下降,MLSS迅速增加,MLVSS和SVI急剧缩小,说明活性污泥中的活性微生物逐渐减少,而无机物组分逐渐增多;钙离子的加入促使系统碳酸平衡向右移动,使离子状态的钙大部分转化为难降解的碳酸盐,并附着于污泥絮体上,污泥绒粒被压缩,使污泥颗粒密实度及MLSS迅速增加,导致污泥排放量巨大。 相似文献
10.
Paper sludges were traditionally landfilled or burned. Over the years, the use of paper sludges on soils has increased, as well as the concerns about their environmental effects. Therefore, the chemical characterization of paper sludges and their young (immature) compost needed to be investigated, and over 150 inorganic and organic chemicals were analyzed in de-inking paper sludge (DPS). In general, nitrogen, phosphorus and potassium contents were low but variable in raw DPS and its young compost. The contents of arsenic, boron, cadmium, cobalt, chromium, manganese, mercury, molybdenum, nickel, lead, selenium, and zinc were also low and showed low variability. However, the copper contents were above the Canadian compost regulation for unrestricted use and required a follow-up. The fatty- and resin acids, and polycyclic aromatic hydrocarbons were the organic chemicals measured at the highest concentrations. For resinic acids, care should be taken to avoid that leachates reach aquatic life. For polycyclic aromatic hydrocarbons, naphthalene should be followed until soil content reaches 0.1 microg g(-1), the maximum allowed for soil use for agricultural purposes according to Canadian Environmental Quality Guidelines. In young compost, the concentration of these chemical families decreased over time and most compounds were below the detection limits after 24 weeks of composting. In raw DPS, among the phenol, halogenated and monoaromatic hydrocarbons, dioxin and furan, and polychlorinated biphenyl families, most compounds were below the detection limits. The raw DPS and its young compost do not represent a major threat for the environment but can require an environmental follow-up. 相似文献
11.
Interaction between pollutants produced in sewage sludge combustion and cement raw material 总被引:3,自引:2,他引:3
Nowadays the use of waste as secondary fuel in clinker kilns is an extensive practice, but the interaction between cement raw material (CRM) and the combustion gases of the fuels has not been extensively studied. Because of that, in this work the effect of the interaction of exhaust from the combustion of sewage sludge and CRM has been studied in a laboratory furnace. The experiments were performed at 300 degrees C, close to the temperature at the cyclones in a cement industry. The behavior of volatile compounds, polycyclic aromatic compounds (PAH) and polychloro dibenzo-p-dioxin and polychloro dibenzofurans (PCCD/F) were analysed in the presence or absence of CRM. The results obtained show that the presence of CRM at the outlet of the combustion gases is beneficial for the decrease of pollutant emissions. 相似文献
12.
13.
14.
pH对剩余污泥和初沉污泥水解酸化的影响已有报道,但pH对混合污泥水解酸化的影响尚鲜见报道。为此对厌氧环境,(20±1)℃,pH=4~11以及不控制pH条件下混合污泥的水解酸化特征进行了研究。研究发现:对pH调控有利于污泥SCOD的溶出,在较强的碱性条件下污泥溶出的SCOD要大于其他条件下的,特别是pH=10和11条件下污泥溶出的SCOD要远高于其他条件下。碱性环境和酸性环境以及中性环境相比更有利于混合污泥产酸,最佳产酸pH条件为pH=10。在酸性和极端碱性条件下均有利于混合污泥中氨氮和磷的释放。碱性环境利于挥发性悬浮固体(VSS)的去除,但不利于总悬浮固体(TSS)的去除。在不同pH条件下将混合污泥的发酵特征和剩余污泥和初沉污泥发酵特征比较,发现3种污泥水解和产酸均在碱性条件下最好,且在20~22℃的条件下,产酸量均在pH=10的条件下达到最大。 相似文献
15.
pH对污水污泥中污染物浸出的影响 总被引:2,自引:1,他引:2
研究pH对污泥中污染物浸出的影响可以为投海过程中海洋水体酸碱性变化对污泥中污染物浸出的影响及其变化规律提供理论依据。为了得出不同pH值对污泥中污染物浸出的影响,采用CEN/TS 14429:2005浸出实验对上海5个污水处理厂脱水污泥中重金属、溶解性有机碳、溶解性硫化物和主要离子的浸出情况进行了研究,同时分别以超纯水和海水为浸提剂研究在相应pH范围内盐度对上述指标浸出的影响。结果表明,Zn、Cd、Pb和As在酸性和碱性条件下浸出量较高,在中性或接近中性条件下浸出量则最低,且海水中Zn和Cd的浸出量比超纯水中高;Cu在碱性条件下的浸出量明显比酸性条件高;在所研究的pH范围内,5个污泥样品中溶解性有机碳的浸出量均随pH的升高而增高;仅酸挥发性硫含量最高的S5在海水中有较明显的溶解性硫化物浸出;部分污泥样品中的氮在酸性纯水中有较高的浸出量,海水中浸出量较少;而无论海水或纯水中,磷在强酸和强碱条件下均有明显浸出。 相似文献
16.
以硅酸盐和铝盐为原料,通过共聚反应制备了2种Si/Al摩尔比的聚硅酸硫酸铝 (PASS) 絮凝剂。以某市政污水厂污泥为研究对象,比较了PAC和PASS调理后污泥比阻 (SRF) 、毛细吸水时间 (CST) 和泥饼含水率,并分析了胞外聚合物 (EPS) 的蛋白和多糖变化规律分析。结果表明,PASS能够有效的降低SRF、CST和泥饼含水率,且PASS的Si/Al摩尔比为1∶1时,脱水效果最好。经过PASS以及PAC调理后,溶解性EPS (SEPS) 和松散附着EPS (LBEPS) 的蛋白多糖的含量均有下降,而PAC调理后紧密附着层EPS (TBEPS) 下降,PASS调理后却存在上升阶段。通过污泥扫描电子显微镜 (SEM) 发现,污泥絮体表面由光滑、均匀分布变成了粗糙多孔,且Si/Al摩尔比为1∶1时孔隙率及孔径最大。SEPS和LBEPS蛋白多糖与CST和SRF具有正相关性。所制PASS的不计动力和设备损耗的工程成本比PAC要低。本研究结果可为PASS用于污泥脱水提供参考。 相似文献
17.
滤布是淤泥脱水过程中重要的过滤材料,实验选用5种滤布(3927、621、758、750A、750B)作为淤泥脱水过程中的过滤材料,探究了滤布种类对淤泥脱水过程中渗透性能的影响,并通过扫面电镜观察淤泥在不同滤布表面的附着情况,基于最佳滤布,引入织物平滑剂、毛毯柔软剂及氟表面活性剂等3种表面活性剂并采用自然干燥和烘箱烘干等2种不同干燥方式改性滤布,通过测定表面接触角表征改性后滤布表面亲疏水性能,并探究了不同表面活性剂种类及干燥方式所得改性滤布对淤泥脱水过程中渗透性能的影响,最后通过扫描电镜对比改性前后750B滤布负载过滤后淤泥颗粒附着情况。结果表明,滤布750B作为过滤材料时淤泥渗透性能最佳。对比6种改性方式所得改性750B滤布,采用氟表面活性剂改性并在烘箱中105℃烘2 h所得改性滤布在负载过滤实验中所得渗透系数及渗水量最大,渗透性能大幅提升。 相似文献
18.
The supercritical water oxidation (SCWO) of industrial tannery sludge was investigated to understand the simultaneous destruction of organic pollutants and recovery of high content chromium. Experiments were performed in a batch reactor at temperatures of 350–500 °C, reaction time of 150–300 s and different oxygen ratios, to exhibit the effect of operation conditions. Results showed that removal efficiency of chemical oxygen demand (COD) increased with higher temperature, larger oxidant amount and reaction time; a maximum value of 96% was obtained. Meanwhile, destruction yield was much higher under supercritical conditions than that in subcritical water. In addition, removal efficiency of Cr from sludge reached more than 98% under all conditions; higher temperature played a positive role. Further, leaching toxicity tests of heavy metals in solid products were conducted based on toxicity characteristic leaching procedure. All heavy metals except nickel showed a greatly reduced leaching toxicity through their stabilization. The chromium oxide recovered in ash was amorphous below 550 °C, so that the structure of Cr could not be identified by X-ray diffraction pattern. Special attention should be paid on nickel as its leaching toxicity increased due to the corrosion of reactor surface under severe reaction conditions. 相似文献
19.
利用Fluent软件选用混合模型,采用多孔介质模型对厢式隔膜压滤机单个滤室内污泥两相流体进行模拟仿真,得到不同过滤压力下滤室内流体的体积分数轮廓图、压强云图,得出滤饼含水率与过滤压力大小的关系。实验结果表明,模拟和实验结果具有较好的一致性。过滤压力在0.4 MPa到1.0 MPa之间,滤饼含水率随过滤压力的增大而大幅度下降;过滤压力1.0 MPa到1.6 MPa之间,滤饼含水率随过滤压力的增大,下降幅度较小;综合考虑能耗且获得低含水率的滤饼,过滤压力的合理取值为1.0 MPa。 相似文献