Trace and major element pollution originating from coal ash suspension and transport processes

Coal ash obtained by coal combustion in the "Nikola Tesla A" power plant in Obrenovac, near Belgrade, Yugoslavia, is mixed with water of the Sava river and transported to the dump. In order to assess pollution caused by leaching of some minor and major elements during ash transport through the pipeline, two sets of samples (six samples each) were subjected to a modified sequential extraction. The first set consisted of coal ash samples taken immediately after combustion, while the second set was obtained by extraction with river water, imitating the processes that occur in the pipeline. Samples were extracted consecutively with distilled water and a 1 M solution of KCl, pH 7, and the differences in extractability were compared in order to predict potential pollution. Considering concentrations of seven trace elements as well as five major elements in extracts from a total of 12 samples, it can be concluded that lead and cadmium do not present an environmental threat during and immediately after ash transport to the dump. Portions of zinc, nickel and chromium are released during the ash transport, and arsenic and manganese are released continuously. Copper and iron do not present an environmental threat due to element leaching during and immediately after the coal ash suspension and transport. On the contrary, these elements, as well as chromium, become concentrated during coal ash transport. Adsorbed portions of calcium, magnesium and potassium are also leached during coal ash transport.     

Indoor air exposure to coal and wood combustion emissions associated with a high lung cancer rate in Xuan Wei, China

Residents of Xuan Wei County in China have unusually high lung cancer mortality that cannot be attributed to tobacco use or occupational exposure. They are exposed to smoke from unvented, open pit coal or wood fires (often used for cooking and heating). The variation in lung cancer rates among communes within the county suggests that indoor combustion of smoky coal may be the prime determinant of lung cancer. To characterize the air in Xuan Wei homes, samples of air particles and semivolatile organic compounds were collected from homes located in two communes; one commune has a high rate of lung cancer, and the other has a low rate. Samples collected in the commune where the lung cancer rate is high and where smoky coal is the predominant fuel contained high concentrations of small particles with high organic content; organic extracts of these samples were mutagenic. Samples from homes in the wood-burning commune, which has a low rate of lung cancer, consisted mostly of larger particles of lower organic content and mutagenicity. The smoky coal sample was a mouse skin carcinogen and was a more potent initiator of skin tumors in comparison to the wood or smokeless coal sample.     

武汉市无公害蔬菜生产的问题与对策

介绍了我国部分城镇在粮食作物和蔬菜产品受化学农药等有害化学物污染简况和无公害蔬菜的研究进展。调查分析了武汉市目前蔬菜生产中农药污染的现状与问题，提出了在武汉市实施无公害蔬菜生产示范工程项目的建议和对策，并进行了讨论。     

The effects of ventilation on residential air pollution due to emissions from a gas-fired range

The use of indoor combustion appliances can cause an increase in the levels of many different pollutants. The work presented here shows the usefulness of a model for extrapolating environmental chamber results on pollutant emissions from combustion appliances to determine indoor pollutant concentrations in actual residences. In addition, the effects of infiltration, whole-house ventilation, and spot ventilation on pollutant levels are investigated. The results show that a range hood is the most effective means of removing pollutants emitted from a gas-fired range; removal rates varied from 60% to 87%.     

Combustion and emission characteristics of a direct injection CI engine when operated on Marotti oil methyl ester and blends of Marotti oil methyl ester and diesel

This paper presents a feasibility study of Marotti oil biodiesel as an alternative to diesel fuel for a compression ignition engine. Marotti oil is inedible and available mainly in the state of Kerala. The oil is extracted from Marotti seeds. However, the high viscosity, poor volatility and cold flow characteristics of many vegetable oils in general, and Marotti oil in particular, can cause problems such as injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication from long-term use in diesel engines. These problems can be eliminated or minimised by transesterification of the vegetable oils to form monoesters. Although transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than for petroleum diesel fuel. Subsequently, Marotti oil was converted into its methyl ester by the process of transesterification. The methyl ester was blended with diesel in various proportions to obtain different blends of Marotti oil with diesel. The performance, emission and combustion characteristics of Marotti methyl ester and its blends with diesel were studied and the results were compared with the base line data generated for diesel operation. Experiments were conducted using an injection timing of 23° before top dead centre (BTDC) and an injection pressure of 205 bar at various power outputs and at a constant rated speed of 1500 rpm. The engine manufacturer specifies an injection timing of 23° BTDC and injection pressure of 205 bar for the standard diesel fuel operation. The heat release rates, maximum rate of pressure rise, ignition delay and combustion duration for these fuel combinations were obtained.

From the results obtained, it was observed that the biodiesel produced from Marotti oil and its blends with diesel have slightly reduced brake thermal efficiency and increased smoke, hydrocarbon, carbon monoxide and reduced NO _x emissions compared with diesel-only operation. The investigation showed that the B20 biodiesel blend of Marotti oil with diesel produced better performance in terms of higher brake thermal efficiency, lower specific fuel consumption and comparatively lower emissions compared to the other blend ratios considered.     

循环经济理论及其在中国实践研究

循环经济理论在国际上尚处于探索与发展过程的过程中，本文运用系统科学和实证研究的方法，对我国循环经济理论与实践问题进行了初步分析。     

Relevance of BFRs and thermal conditions on the formation pathways of brominated and brominated-chlorinated dibenzodioxins and dibenzofurans

The widespread use of brominated flame-retarded products in the last two decades has resulted in an increasing presence of bromine in thermal processes such as waste combustion and accidental fires. Brominated and brominated-chlorinated dibenzodioxins and dibenzofurans (PBDDs/PBDFs, PXDDs/PXDFs) are micropollutants of concern arising from such processes. The present review aims to evaluate the relevance of these compound classes in actual thermal processes. Four categories of thermal processes are discussed in this respect according to their potential for PBDD/PBDF and PXDD/PXDF generation: thermal stress, pyrolysis/gasification, insufficient combustion conditions and controlled combustion conditions. Under thermal stress situations, as they may occur in production or recycling processes, PBDDs/PBDFs precursors like polybrominated diphenylethers (PBDE) can have a relevant potential for PBDD/PBDF formation via a simple elimination. Under insufficient combustion conditions as they are present in, e.g. accidental fires and uncontrolled burning as well as gasification/pyrolysis processes, considerable amounts of PBDDs/PBDFs can be formed from BFRs, preferably via the precursor pathway. In contrast, under controlled combustion conditions, BFRs and PBDDs/PBDFs can be destroyed with high efficiency. The relevance of de novo synthesis of PXDDs/PXDFs is discussed for this condition.Providing a basis for the understanding of PXDD/PXDF formation in actual thermal processes, the present paper also summarises the formation pathways of brominated and brominated-chlorinated PXDDs/PXDFs from brominated flame retardants (BFRs) investigated during laboratory thermolysis experiments. Relevant mechanistic steps for PBDD/PBDF formation from brominated precursors are discussed including elimination reactions, condensation steps and debromination/hydrogenation reactions.In addition, chlorination/bromination and halogen exchange reactions are briefly discussed with respect for their relevance on the final distribution of PBDDs/PBDFs, mixed chlorinated PXDDs/PXDFs and PCDDs/PCDFs resulting from thermal processes.     

E-waste recycling induced polybrominated diphenyl ethers, polychlorinated biphenyls, polychlorinated dibenzo-p-dioxins and dibenzo-furans pollution in the ambient environment

Polybrominated diphenyl ethers (PBDEs) have been determined in 30 samples, including soil, biota and plant collected from an electronic waste recycling site and its vicinage towns. Polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins and dibenzo-furans (PCDD/Fs) were also simultaneously analyzed in 20 samples. PBDEs were detected in all soil samples and the highest was up to 789 ng/g dry weight (dw). The toxic equivalency (TEQ) of PCBs and PCDD/Fs detected in E-waste recycling site is significant higher than those in the vicinage samples. Biota and plant were also contaminated with high level of PBDEs, PCBs and PCDD/Fs in this area. High levels of the three kinds of organic compounds in the environmental samples showed that the E-waste recycling have induced serious environmental problems.     

喀斯特生态治理区可持续发展能力评价——以贵州毕节鸭池、遵义龙坪、沿河淇滩示范区为例

为检验喀斯特生态治理区的治理效果,以贵州省毕节鸭池、遵义龙坪、沿河淇滩3个示范区为例,从资源承载力、环境支持力、人口发展与支持能力、经济发展能力、社会发展能力5个方面,选择45个单项指标,建立评价指标体系,采用“纵横向”拉开档次动态综合评价法,评价3个示范区2005、2007年的可持续发展能力。结果显示：空间上看,龙坪示范区的可持续发展能力最好,鸭池示范区次之,淇滩示范区最差;时间上对比,龙坪示范区和淇滩示范区的发展能力2007年比2005年有所提高,〖JP2〗鸭池示范区稍有退步。根据各示范区的主要人 地矛盾,提出控制人口、优化配置水土资源、加大林牧产业比重等对策,以提高其可持续发展能力,并为同类地区的可持续发展提供借鉴。     

长江流域湿地保护、修复与生态管理策略

从长江流域生态系统长期演化的视角,分析了长江流域自然与湿地环境演变特征,归纳了长江流域湿地资源概况,分别总结了长江源区、三峡库区湿地区、中游湖泊群以及长江三角洲湿地的区域性特征及其面临的威胁因素,论述了典型重要湿地区域湿地保护与生态工程建设的示范案例,在此基础上探讨了长江流域湿地保护、修复与生态管理的对策和建议,旨在助力于长江大保护,为长江流域湿地的保护和科学管理提供依据。     

Regulatory options for the development of health and environmental testing of diesel fuels and fuel additives

This paper discusses various options for regulations of fuels and fuel additives. Four options of evaluation of combustion products are described. These are disregarding combustion products, complete analysis, testing of exhaust mixtures, and partial analysis. Tests are adapted from regulations of EPA for evaluation of combustion products.     

Study of total organic halogen as a means to detect groundwater contamination

Total organic halogen (TOX) was evaluated as a means to detect contamination of groundwater by halogenated organics. Groundwater samples from monitoring wells at 10 Canadian landfill sites were analyzed for carbon adsorbable TOX, total organic carbon and volatile organics. Low concentrations of TOX (range, ND-44; median 8 μg Cl L^?1) were found at nine sites, and elevated TOX levels (?2072 μg Cl L^?1) at the tenth site. This latter site was studied in greater detail, and TOX and GC-MS analyses were carried out for volatile, base neutral, and acid extractable fractions of the water in six monitoring wells at this site. The TOX and GC-MS techniques were found to provide complementary information. GC-MS analysis detected high concentrations of 1,2-dichloroethylene, trichloroethylene, toluene, and ethylbenzene in some of the wells. TOX measurements, however, indicated the presence of halogenated contaminants in the base-neutral and acid extractable fractions, which had not been detected by GC-MS.     

An estimation of radiation doses to benthic invertebrates from sediments collected near a Canadian uranium mine.

A new method is described for calculating radiation doses to benthic invertebrates from radionuclide concentrations in freshwater sediment. Both internal and external radiation doses were estimated for all 14 principal radionuclides of the uranium-238 decay series. Sediments were collected from three sites downstream of a uranium mining operation in northern Saskatchewan, Canada. Sediments from two sites, located approximately 1.6 and 4.4 km downstream from mining operations, yielded absorbed doses to both larval midges, Chironomus tentans, and adult amphipods, Hyalella azteca, of 59-60 and 19 mGy/year, respectively, compared to 3.2 mGy/year for a nearby control site. External beta radiation from protactinium-234 (234Pa) and alpha radiation from uranium (U) contributed most of the dose at the impacted sites, whereas polonium-210 (210Po) was most important at the control site. If a weighting factor of 20 was employed for the greater biological effect of alpha vs. beta and gamma radiation, then total equivalent doses rose to 540-560 mGy/year at the site closest to uranium operations. Such equivalent doses are above the 360-mGy/year no-observed-effect level for reproductive effects in vertebrates from gamma radiation exposure. Data are not available to determine the effect of such doses on benthic organisms, but they are high enough to warrant concern. Detrimental effects have been observed in H. azteca at similar uranium concentration in laboratory toxicity tests, but it remains unclear whether the radiotoxicity or the chemotoxicity of uranium is responsible for these effects.     

Enhanced oil recovery: Environmental issues and state regulatory programs

During 1977–1978, Oak Ridge National Laboratory (ORNL) prepared environmental impact assessments for nine U.S. Department of Energy-sponsored enhanced oil recovery (EOR) field demonstration projects located in six states and reviewed the oil regulations for all oil-producing states. These evaluations revealed some potentially important environmental impacts associated with EOR including (1) pollution of land and surface waters from spills or leaks of oil and brine or other chemicals, (2) loss of biota, (3) excessive erosion and sedimentation (mostly in hilly terrain) and subsequent deterioration of surface-water quality, (4) contamination of groundwater, and (5) excessive air emissions from thermal operations. Potential groundwater impacts include (1) production of toxic and carcinogenic substances from synergistic interactions among chemicals used primarily in the micellar-polymer flooding technique, (2) formation of acid waters with small amounts of oil and metal residues and oxides from in situ combustion, and (3) corrosion of well casings and potential leaks of hydrogen sulfide primarily from injection of miscible carbon dioxide. For use of EOR techniques to expand in an environmentally acceptable manner, environmental planning (including monitoring, protection measures, and reclamation strategies) must be an integral part of the initial project development. Acceptable monitoring, prevention, mitigation, and reclamation procedures are available for most of the identified environmental problems, but the best techniques may not be known by operators or required by law. Most states have stringent controls for plugging abandoned wells and disposal of waste material, but these may not be enforced because of limited staff and funds. However, other environmental considerations, e.g., reclamation plans, water quality and other monitoring programs, and abandonment plans, are often lacking. The need for additional environmental planning and monitoring requirements specific to the oil-production industry is emphasized. States are encouraged to continue strengthening and upgrading their oil-regulatory programs to safeguard the environment. More studies are needed on (1) toxicity and carcinogenicity of chemicals used in injection processes, (2) evaluation of groundwater monitoring methods, and (3) reclamation procedures for soils contaminated by oil and brine.     

Pollutant emission rates from indoor combustion appliances and sidestream cigarette smoke

Particulate and gaseous emissions from indoor combustion appliances and smoking can elevate the indoor concentrations of various pollutants. Indoor pollutant concentrations resulting from operating one of several combustion appliances, or from sidestream tobacco smoke, were measured in a 27-m³ environmental chamber under varying ventilation rates. The combustion appliances investigated were gas-fired cooking stoves, unvented kerosene-fired space heaters, and unvented natural-gas-fired space heaters. Results showed elevated levels of carbon dioxide, carbon monoxide, nitric oxide, nitrogen dioxide, formaldehyde, and suspended particles from one or more of the pollutant sources investigated. Our findings suggest that, of the sources examined in this study, nitrogen dioxide from combustion appliances and particles from sidestream cigarette smoke are the most serious contaminants of indoor air, if we use existing standards and guidelines as the criteria. An emission rate model was used to quantify the strengths of the pollutant sources, which are reported in terms of the mass of pollutant emitted per energy unit of fuel consumed (in the case of gas and kerosene appliances) and per mass of tobacco combusted (in the case of smoking).     

Human induced salinisation and the use of quantitative methods

Sustainable development of the earth's limited water and land resources is of paramount importance because of rising world population and existing conflicting demands for these resources. Enormous capital investment has been made in developing these resources, but now there is irrefutable evidence that such developments have led to major resource degradation. This includes problems of salinisation and damages to ecosystems. The countries predominantly affected by human induced salinisation are located in arid and semi-arid regions of the world and include Australia, China, Egypt, India, Pakistan, USSR, and USA. This paper describes the processes of salinisation, its impacts and the use of quantitative methods in salinity investigation and management. Australia is used as a case study of typical salinity problems and as a demonstration of the fruitful application of quantitative methods. The paper concludes that quantitative methods such as surface water and groundwater models are powerful design, management and predictive tools in salinity investigation. However, application of some models, such as those for unsaturated flow and transport and groundwater solute transport, are not widespread due to uncertainties in describing the complexity of the processes and the lack of hydrodispersive data.     

Assessment of the radiological impacts of historical coal mining operations on the environment of Ny-Alesund, Svalbard

Mineral extraction activities, such as those conducted by oil, gas and coal industries, are widespread throughout the Arctic region. Waste products of these activities can result in significant contributions to the radioactive burden of the surrounding environment due to increased concentrations of naturally occurring radioactive materials (NORM) to levels that would not normally be found in the environment. Coal mining operations commenced in the early 1900s on Svalbard and have been conducted at a variety of locations on the archipelago since then. Coal contains radionuclides of the uranium and thorium series as well as 40K. Extraction and processing of coal can result in releases of these radionuclides to the broader environment with subsequent impact on the human and non-human inhabitants of the area. This paper presents the results of a study on environmental radioactivity resulting from historical coal mining operations conducted at Ny-Alesund, Spitsbergen, in the Svalbard archipelago. Activity concentrations of radionuclides found in materials associated with these operations are presented as well as the results of a spatial dosimetric survey conducted over an area affected by coal mining.     

生态修复产业化模式研究——以北京门头沟国家生态修复示范基地为例

生态修复是对区域受损害自然生态系统过程和功能的重建,往往偏重于技术的研究和应用示范。但随着传统生态修复在区域实践过程中产生的经济瓶颈,尤其是面临区域产业转型问题的突显,生态修复的产业化及其运行模式已成为国内外学者关注的重点。本文以北京门头沟国家生态修复示范基地为例,从产业复合生态系统角度,突破传统产业限制,建立了自然生态修复示范产业、人文生态修复主导产业和经济生态修复引导产业三位一体的产业网络模式,并针对示范基地内的各种具体生态修复领域进行了产业生态链(网)的设计。最后对建立这种新型生态修复产业模式的意义和所面临的问题进行了探讨。     

Determination of organically bound tritium background level in biological samples from a wide area in the south-west of France

In this paper, the authors describe a sensitive method for low-level non-exchangeable OBT determination. This methodology combines suitable sample treatment, a combustion apparatus for large-sized samples and low-background liquid scintillation spectrometry, along with precautions that substantially reduce the risks of sample contamination. Great care must be taken in the measurement of non-exchangeable OBT at environmental levels. Many authors have discussed the opportunities for cross-contamination between samples and contamination by exchange with the laboratory atmosphere. The authors also describe an application of the methodology to a large-scale sampling and measurement campaign, aimed at the determination of the environmental non-exchangeable OBT background level in tree leaves and ferns collected on the site and in the vicinity of a research centre located in the south-west of France, not far from Bordeaux. This study constitutes a "zero level" for the non-exchangeable OBT activity, as, to our knowledge, there is no tritium source within or in the surroundings of the sampled area capable of producing non-exchangeable OBT activities above the natural levels. Our analyses showed that non-exchangeable OBT activities in the collected samples were very low, ranging from below the detection limit (ca 0.7 Bq kg(-1) of dry material) to ca 2 Bq kg(-1) of dry material. These values are similar to the natural tritium background measured in water samples. No discrepancies can be shown between fern samples and oak tree leaf samples or between samples collected inside and outside the research site.