CuO对贵金属/CeO2/Al2O3催化剂的作用

制备含少量贵金属Ｐｔ、Ｐｄ的不同Ｃｕ和Ｃｅ摩尔含量比（０：１０,１：９,２：８）的催化剂,实验条件十加入ＣｕＯ可以提高Ｐｔ催化剂的二效活性;加入Ｃｕ：Ｃｅ＝２：８的ＣｕＯ降低了Ｐｄ催化剂的顾效性能,然而Ｃｕ：Ｃｅ＝１：９时可以改善Ｐｄ催化剂的三效催化性能。通过结构分析,认为ＣｕＯ的存在可以提高ｄ催化剂的比表面积,ＰｄＯ的分散度。     

地下水脱硝催化剂的制备及其性能研究

以Al2O3为载体制备了负载型催化剂,通过甲酸催化还原脱除地下水中硝酸盐对该催化剂进行了活性评价,并研究了催化剂制备条件对催化性能的影响,发现催化剂种类、配比及其含量不同,催化剂的催化性能也相应发生变化,其中4%Pd-1%Cu/Al2O3催化剂可以在45min内将100mg/L的NO3-被完全去除。     

Effect of phosphate on heterogeneous Fenton oxidation of catechol by nano-Fe3O4: Inhibitor or stabilizer?

The effect of phosphate on adsorption and oxidation of catechol, 1,2-dihydroxybenzene, in a heterogeneous Fenton system was investigated. In situ attenuated total reflectance infrared spectroscopy (ATR-FTIR) was used to monitor the surface speciation at the nano-Fe₃O₄ catalyst surface. The presence of phosphate decreased the removal rate of catechol and the abatement of dissolved organic compounds, as well as the decomposition of H₂O₂. This effect of phosphate was mainly due to its strong reaction with surface sites on the iron oxide catalyst. At neutral and acid pH, phosphate could displace the adsorbed catechol from the surface of catalyst and also could compete for surface sites with H₂O₂. In situ IR spectra indicated the formation of iron phosphate precipitation at the catalyst surface. The iron phosphate surface species may affect the amount of iron atoms taking part in the catalytic decomposition of H₂O₂ and formation of hydroxyl radicals, and inhibit the catalytic ability of Fe₃O₄ catalyst. Therefore, phosphate ions worked as stabilizer and inhibitor in a heterogeneous Fenton reaction at the same time, in effect leading to an increase in oxidation efficiency in this study. However, before use of phosphate as pH buffer or H₂O₂ stabilizer in a heterogeneous Fenton system, the possible inhibitory effect of phosphate on the actual removal of organic pollutants should be fully considered.     

Removal of metals by sorghum plants from contaminated land

The growth of high biomass crops facilitated by optimal of agronomic practices has been considered as an alternative to phytoremediation of soils contaminated by heavy metals. A field trial was carried out to evaluate the phytoextraction efficiency of heavy metals by three varieties of sweet sorghum (Sorghum biocolor L.), a high biomass energy plant. Ethylene diamine tetraacetate (EDTA), ammonium nitrate (NH₄NO₃) and ammonium sulphate ((NH₄)₂SO₄) were tested for their abilities to enhance the removal of heavy metals Pb, Cd, Zn, and Cu by sweet sorghum from a contaminated agricultural soil. Sorghum plants always achieved the greatest removal of Pb by leaves and the greatest removal of Cd, Zn and Cu by stems. There was no significant difference among the Keller, Rio and Mray varieties of sweet sorghums in accumulating heavy metals. EDTA treatment was more efficient than ammonium nitrate and ammonium sulphate in promoting Pb accumulation in sweet sorghum from the contaminated agricultural soil. The application of ammonium nitrate and ammonium sulphate increased the accumulation of both Zn and Cd in roots of sorghum plants. Results from this study suggest that cropping of sorghum plants facilitated by agronomic practices may be a sustainable technique for partial decontamination of heavy metal contaminated soils.     

低分子量有机酸提取土壤中部分重金属的拟合模型研究

为研究不同浓度低分子量有机酸与提取的土壤重金属含量之间的关系,本文以采自安徽省安庆市某铜矿区及其周围的土壤为例,通过浸提法,研究了不同浓度苹果酸、甲酸对采样点土壤中重金属Cu、Mn、Zn、Pb提取能力的影响并进行模型拟合.结果表明:不同浓度苹果酸和甲酸对采样点土壤中重金属的提取量不同,两种有机酸对低pH、高重金属含量采样点及其周围土壤中的重金属提取量较大,两种低分子量有机酸对S6采样点的重金属Mn的提取量最大,分别为322.5 mg·kg~(-1)和193.58 mg·kg~(-1),提取率达70.02%和42.03%,Zn、Pb次之,Cu最低;随着苹果酸、甲酸浓度的升高,土壤中重金属Cu、Mn、Zn、Pb的提取量增加,苹果酸对土壤中重金属的提取能力大于甲酸;拟合模型对于两种低分子量有机酸与其提取的土壤中部分重金属含量之间的关系,具有较好的拟合性,其决定系数R~2在0.8293～0.9990之间,都具有显著性(p0.05),该模型可以定量表征低分子量有机酸对土壤重金属的提取能力,此研究结果为土壤中重金属的固定化和增强植物修复受重金属污染的土壤提供了理论支持.     

Pd-Cu/石墨烯协同零价铁(Fe0)的催化反硝化实验

为解决城市污水处理厂二级出水中硝态氮含量较高的问题,对Pd-Cu/石墨烯协同零价铁（Fe0）的新型催化反硝化法处理水体中NO₃--N进行了深入研究,重点对催化反硝化操作条件进行了优化。研究发现,新型催化反硝化法获得较好催化效果的最佳运行条件为:Fe0投加量为4 g/L,m（Pd）:m（Cu）为3:1,溶液pH为4.2,Pd-Cu/石墨烯投加量为4 g/L,反应时间为2 h,此时系统的NO₃--N去除率及N₂转化率分别为78%和74%。在催化反硝化反应中,Fe0主要以电子供体存在,其在一定的酸性条件下,可触发催化反应的发生。催化反应发生在催化剂的金属活性位（Pd和Cu）上。NO₃--N在催化剂作用下,通过脱氧反应被逐步去除并转化为N₂。此外,催化剂载体及催化反应中的传质效果也是影响催化效果的重要因素。     

金属掺杂二氧化钛光催化还原硝酸氮

采用光沉积法制备了负载金属Fe或Cu的P25二氧化钛光催化剂,用TEM、ICP、XRD及UV-Vis等对其进行了表征,并测定其在20 W紫外灯照射下光催化还原硝酸氮、去除总氮的效果;考察了pH值、搅拌气体、金属的负载量、空穴清除剂甲酸的用量以及金属Ag-Cu复合沉积等条件的影响.反应2 h的结果表明,二氧化钛上载铜量增加,硝酸氮转化率随之增加,但最大总氮去除率和氮气选择性均出现在0.5%Cu负载量下;氮气搅拌和酸性条件下反应,形成氮气的选择性略低(62%),但最高的硝酸氮转化率和总氮去除率分别达到36.9%和23.2%;CO2作为搅拌气体.Cu的负载量为0.5%、甲酸用量为0.06 mol/L时.形成氮气选择性最好(88.4%).硝酸氮转化率和总氮去除率分别为29.5%和25.1%.同样条件下,采用二氧化钛上共沉积金属总质量分数为1%、Ag:Cu=1:1的催化剂,硝酸氮的转化率可达48.1%,总氮去除率为34.2%,氮气选择性为72.2%.     

用于降解4-氯酚的载钯碳纳米管催化电极研究

采用不同体积分数的硝酸溶液（8%、15%、20%、68%）对多壁碳纳米管（MWNTs）进行预处理,使用甲醛还原方法制备出Pd/MWNTs催化剂,利用Boehm滴定法、红外光谱分析、X射线衍射（XRD）、扫描电子显微镜（SEM）及循环伏安曲线（CV）对催化剂进行表征分析,并制备成Pd/MWNTs催化阴极,在隔膜电解体系中...     

富氧条件下等离子体协同改性NaY分子筛催化分解NO_x研究

用不同浓度的Cu、Ce和La离子交换Na Y分子筛,对比了不同改性条件下等离子体协同分解NO_x的性能.实验结果表明:Cu是NO_x催化分解的主要活性组分,对于8%Cu-Na Y催化剂,当放电电压为10 k V,放电功率为7.6 W时,NO_x转化率可达46.3%,反应产物中没有NO_2,只有11 ppm的N_2O.Ce的加入可以有效提高催化剂催化活性,对于5%Ce-8%Cu-NaY催化剂,当放电电压为7.8 kV,功率为3.6 W时,NO_x转化率可达67.3%.La的加入同样可以使催化剂活性上升,但不同La含量催化剂的NO_x转化率相差较小.     

Pd/CMK-3的合成、表征及对甲酸的电催化氧化性能研究

以中孔硅SBA-15为硬模板、蔗糖为炭源,合成了有序中孔炭CMK-3,并以此CMK-3为载体,采用络合还原法制备了负载量为20%的催化剂Pd/CMK-3.X射线衍射(XRD)和透射电镜(TEM)的结果表明,CMK-3孔结构高度有序,呈现二维六方结构,Pd/CMK-3和Pd/AC(活性炭)催化剂中Pd纳米颗粒分散均匀,平均粒径分别为4.2 nm和4.5 nm;拉曼光谱测试表明,CMK-3比活性炭的石墨化程度更高,导电性更强;N2吸附/脱附实验表明,CMK-3具有典型的中孔结构,CMK-3的最可几孔径为4.5 nm,显著大于活性炭的0.54 nm,CMK-3的BET比表面积为1 114 m2.g-1,大于活性炭的871 m2.g-1.在对甲酸电催化氧化的循环伏安(CV)和计时电流(CA)测试中,Pd/CMK-3的初始催化活性显著高于Pd/AC,而两者在100 s后的计时电流稳定性则基本相当.     

Heterogeneous Fenton-like degradation of 4-chlorophenol using iron/ordered mesoporous carbon catalyst

Ordered mesoporous carbon supported iron catalysts(Fe/OMC) were prepared by the incipient wetness impregnation method and investigated in Fenton-like degradation of 4-chlorophenol(4CP) in this work. XRD and TEM characterization showed that the iron oxides were well dispersed on the OMC support and grew bigger with the increasing calcination temperature. The catalyst prepared with a lower calcination temperature showed higher decomposition efficiency towards 4CP and H2O2, but more metals were leached. The effect of different operational parameters such as initial pH, H2O2 dosage, and reaction temperature on the catalytic activity was evaluated. The results showed that 96.1% of 4CP and 47.4% of TOC was removed after 270 min at 30°C, initial pH of 3 and 6.6 mmol/L H2O2. 88% of 4CP removal efficiency was retained after three successive runs, indicating Fe/OMC a stable catalyst for Fenton reaction. 4CP was degraded predominately by the attack of hydroxyl radical formed on the catalyst surface and in the bulk solution due to iron leaching. Based on the degradation intermediates detected by high performance liquid chromatography, possible oxidation pathways were proposed during the 4CP degradation.     

阴极电解液对Cd污染红壤电动修复的影响

针对土壤重金属电动修复过程中阴极电解室pH升高会对重金属的去除产生不利影响的问题,利用Fe3+/Fe2+、Cu2+/Cu标准电极电位较高的优势,以人工模拟Cd污染红壤为研究对象,对不同阴极电解液[Fe（NO₃）₃、CuSO₄、柠檬酸]的电动修复效果进行系统分析.结果表明:分别将Fe（NO₃）₃、CuSO₄、柠檬酸加入阴极电解室中,pH均控制在2~3,电动修复10 d后发现,将Fe（NO₃）₃溶液、CuSO₄溶液和柠檬酸作为阴极电解液均可以有效控制阴极室的pH,CuSO₄溶液、柠檬酸的加入对土壤中Cd的去除效果较差,而且Cu2+的加入增加了土壤重金属二次污染的风险.相对于CuSO₄、柠檬酸试验组,Fe（NO₃）₃试验组土壤中Cd的去除率较高（大于87.27%）,Fe（NO₃）₃试验组对土壤中Cd的修复效果也最为明显,土壤中w（Cd）由阴极附近的75.95 mg/kg降至阳极附近的9.13 mg/kg.分析电动修复后各试验组中不同形态Cd在Cd总量中所占比例的分析,结果显示,w（弱酸提取态Cd）所占比例由初始的74.57%最高可达到92.69%[Fe（NO₃）₃试验组],表明Fe（NO₃）₃的加入有助于促进土壤中Cd的迁移.研究显示,相比于CuSO₄溶液、柠檬酸,Fe（NO₃）₃溶液作为阴极电解液在控制阴极电解室pH升高的前提下,显著促进了土壤中Cd的解吸和迁移,并达到最佳修复效果.      

铁铜催化剂非均相Fenton降解苯酚及机制研究

通过浸渍法制备了负载于活性炭(AC)上的金属催化剂Fe/AC、Cu/AC和Fe-Cu/AC,并通过X射线衍射(XRD)、物理吸附仪及X射线光电子能谱(XPS)对其进行了表征.研究了非均相Fenton反应催化H2O2降解苯酚废水的工艺参数,并通过中间产物分析和电子自旋共振谱(ESR)探讨了过程反应机制.实验表明,Cu/AC催化剂中铜主要以CuO形式存在,Fe/AC中铁以多价态形式存在,以无定形形态分散于活性炭中.Fe/AC、Cu/AC和Fe-Cu/AC催化过氧化氢降解苯酚60 min内降解率分别达到96.7%、77.5%和99%;Cu/AC和Fe-Cu/AC催化剂中活性组分铜和铁有一定溶出,而Fe/AC中活性组分铁溶出很少,苯酚降解主要是以非均相催化为主,同时在三轮循环实验后的苯酚降解率仍然高达93%以上,显示了良好的催化稳定性.在优化条件pH=3、T=303 K及初始H2O2为4.38 mmol.L-1下,Fe/AC催化过氧化氢对苯酚和TOC去除率分别达到97%和53%,没有催化剂时苯酚几乎不降解.ESR结果表明Fe/AC催化过氧化氢产生了羟基自由基,证明苯酚降解是以羟基自由基氧化为主;通过高效液相色谱(HPLC)检测苯酚降解中间产物主要有邻苯二酚、对苯二酚和对苯醌,推测苯酚降解途径主要为邻位和对位的羟基取代反应.     

Thermal decomposition pathways for peroxyacetyl nitrate (PAN): Implications for atmospheric methyl nitrate levels

The unimolecular decomposition pathways of peroxyacetyl nitrate (PAN) have been investigated in the presence of added NO₂ over the temperature range 298–345 K. The major products of the PAN decomposition were CO₂ and, depending on the ratio of O₂ to NO₂ in the experiment, either CH₂O or methyl nitrate. From the observed PAN decay rates and product yields, upper limits for the direct formation of either NO₃ or methyl nitrate from the unimolecular decay of PAN were obtained. The results indicate that these channels occur with rate constants that are thousands of times slower than dissociation of PAN into peroxyacetyl and NO₂, and that PAN decomposition is not a significant source of atmospheric methyl nitrate.     

Ti-Ce系列催化剂上乙酸的催化湿式氧化反应

采用Ti-Ce系列湿式氧化催化剂,研究模型反应物乙酸在催化湿式氧化反应中的动力学影响因素以及反应过程产物.结果表明,乙酸的催化湿式氧化受到催化剂用量、反应温度、反应体系酸度以及氧分压的影响较大.当反应温度230℃,氧分压2～2.5MPa,催化剂量5g/L,反应液初始pH3.0时,反应1h后即可使乙酸浓度(以COD计)去除率在90%以上.通过离子色谱,检测了反应过程中的甲酸中间体,结果表明,催化剂的存在不仅加速了湿式氧化反应速率,而且也改变了反应历程.     

三峡库区消落带不同水位高程土壤重金属含量及污染评价

为揭示三峡水库连续2 a(2008年和2009年)175 m试验性蓄水对库区消落带土壤重金属的影响,选择了库区腹地忠县境内的3个地质地貌特征、土地利用历史等相似消落带.采集了不同高程(160 m和170 m)和土壤层(0～10 cm和10～20 cm)36个土壤样品,用X射线荧光光谱法测定了As、Cd、Cr、Cu、Ni、Pb和Zn共7种重金属含量,并对其污染现状和潜在生态风险程度进行了评价.结果表明,尽管160 m和170 m高程淹水时间差异较大(244 d),但土壤重金属含量并没有显著差异;重金属相关分析显示Cd相对独立,而其它重金属大都存在着显著或极显著的正相关关系;地累积指数(geoaccumulation index,Igeo)表明重金属污染程度顺序依次为:As>Cd>Cu>Ni>Zn=Pb>Cr,其中As、Cd和Cu地累积指数(Igeo)分别为0.45、0.39和0.06,属轻度污染,其它重金属为无污染;Hkanson潜在生态风险指数(Ei)表明重金属潜在生态风险顺序为:Cd>As>Cu>Pb>Ni>Cr>Zn,其中Cd的潜在生态风险指数(Ei)为59.10,危害风险达中度,其余重金属风险均为较轻.因此污染评价方法指出了该区域消落带土壤的主要污染或存在潜在生态危害的重金属元素为As、Cd和Cu.     

皂角苷和柠檬酸联合对污泥中Cu、Pb和Zn的去除及其稳定性特征

以武汉某污水处理厂的污泥为研究对象(S1和S2),通过皂角苷和柠檬酸联合振荡淋洗试验,研究不同体积比(20∶1~1∶20)、固液比(1∶20~1∶80)、淋洗时间(0~2 880 min)、淋洗次数(1~4)对污泥中重金属Cu、Pb和Zn去除的影响.分析淋洗前后各形态重金属的去除特点,并通过计算稳定性指数(I_R值)和移动性指数(MF值)探究重金属稳定性和移动性的变化.结果表明,在体积比(皂角苷∶柠檬酸)为5∶1,固液比为1∶60,淋洗时间1 440 min时,污泥中Cu、Pb和Zn的最高去除率分别可达43.16%(S1)、32.45%(S2)和38.69%(S1).增加淋洗次数对Cu和Pb的去除率有较大幅度提高,而对Zn的影响较小,尤其在2~3次淋洗后差异显著.4次淋洗后Cu、Pb和Zn的最高去除率分别为78.89%(S1)、77.08%(S2)和49.39%(S1).单次淋洗后,除酸溶态和可还原态外,污泥中其余形态的去除率均较低.增加淋洗次数,重金属的各形态去除率逐渐升高,尤其是Pb中的残渣态去除率增长明显.淋洗改变了重金属的稳定性和移动性,4次淋洗后Cu、Pb和Zn的IR值最大增长率分别为43.63%(S1)、39.44%(S2)和32.00%(S1),MF值减少30.19%~79.45%.     

Field scale interaction and nutrient exchange between surface water and shallow groundwater in the Baiyang Lake region, North China Plain

Fertilizer input for agricultural food production, as well as domestic and industrial surface water pollutants in the North China Plain, increases pressures on locally scarce and vulnerable water resources. In order to: (a) understand pollutant exchange between surface water and groundwater, (b) quantify nutrient loadings, and (c) identify major nutrient removal pathways by using qualitative and quantitative methods, including the geochemical model PHREEQC, a one-year study at a wheat (Triticum aestivum L.) and maize (Zea mays L.) double cropping system in the Baiyang Lake area in Hebei Province, China, was undertaken. The study showed a high influence of low-quality surface water on the shallow aquifer. Major inflowing pollutants into the aquifer were ammonium and nitrate via inflow from the adjacent Fu River (up to 29.8 mg/L NH₄-N and 6.8 mg/L NO₃-N), as well as nitrate via vertical transport from the field surface (up to 134.8 mg/L NO₃-N in soil water). Results from a conceptual model show an excess nitrogen input of about 320 kg/ha/a. Nevertheless, both nitrogen species were only detected at low concentrations in shallow groundwater, averaging at 3.6 mg/L NH₄-N and 1.8 mg/L NO₃-N. Measurement results supported by PHREEQC-modeling indicated cation exchange, denitrification, and anaerobic ammonium oxidation coupled with partial denitrification as major nitrogen removal pathways. Despite this current removal capacity, the excessive nitrogen fertilization may pose a future threat to groundwater quality. Surface water quality improvements are therefore recommended in conjunction with simultaneous monitoring of nitrate in the aquifer, and reduced agricultural N-inputs should be considered.     

等离子体催化降解甲苯途径的原位红外研究

考察了在常温常压条件下,等离子体分别协同SiO₂、Al₂O₃、NiO/Al₂O₃降解甲苯的性能,并从材料的介电常数、对甲苯的吸附性及臭氧分解能力等角度分析了不同活性表现的原因,同时,采用原位红外技术研究了甲苯降解过程中催化剂表面吸附物种的变化.结果表明,当甲苯浓度为100 ppm,气体流量为100 mL·min^-1时,一定范围内,甲苯降解率随着能量密度、介电常数、吸附性及臭氧分解能力的提高而提高.甲苯在催化剂表面的吸附对其降解途径有十分重要的影响:在放电区域中加入SiO₂,甲苯仍然在气相中完成降解;而存在Al₂O₃ 及NiO/Al₂O₃时,甲苯氧化成苯甲酸的过程主要发生在催化剂表面,是甲苯催化降解的关键步骤,苯甲酸在活性位点的积累将降低催化剂的反应活性.     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NOx) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition, NOx was suppressed with the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NOx suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.