金属掺杂对纳米管TiO_2光催化去除水中罗丹明B的影响

采用水热合成法,将Fe(NO3)3·9H2O、ZnCl2和AgNO3对纳米管TiO2进行掺杂,使用TEM、XRD、XPS、比表面积分析仪及UV-visDRS对掺杂后的纳米管TiO2进行表征并考察其光催化氧化去除罗丹明B的效果,从而优选最佳掺杂金属。结果表明,煅烧温度可影响纳米管TiO2锐钛矿相相对含量、比表面积及禁带宽度,进而影响其光催化活性。此外,掺杂金属离子的种类不同,纳米管TiO2的光催化活性也受到影响。500℃煅烧非掺杂纳米管TiO2的存在下,光催化氧化罗丹明B的去除率为98.72%。向纳米管TiO2中掺杂Fe3+、Zn2+及Ag+时,光催化氧化罗丹明B的效果得到提高。对以上三种掺杂金属离子而言,掺杂量为1.0%(原子百分含量)的催化剂的最佳煅烧温度为550℃。其中,Fe3+掺杂纳米管TiO2光催化活性最高,50min内光催化氧化罗丹明B的去除率可达99.0%。     

Fe~(3+)及Ce~(3+)掺杂对TiO_2纳米粒子性能的影响

以溶胶-凝胶法制备纯的和分别掺杂Fe3+、Ce3+的TiO2纳米粒子,以橙黄IV的光催化氧化评价纳米粒子的紫外光与可见光活性,利用TG-DSC、XRD、BET及UV-Vis吸收光谱考察掺杂对TiO2的相变、粒径、比表面积及光吸收性能的影响,在归一化条件下探讨Fe3+及Ce3+掺杂对TiO2活性和表面性质产生影响的机制。结果表明:Fe3+及Ce3+的最佳掺杂量分别为0.2%和0.04%;Ce3+抑制TiO2由锐钛矿向金红石转变以及改善TiO2高温组织稳定性的能力均明显大于Fe3+;Fe3+和Ce3+掺杂均能提高TiO2的紫外光活性并扩展TiO2的光响应范围,但光生电子与空穴复合以及光腐蚀使它们对TiO2可见光活性的提高并不显著。Fe3+和Ce3+的半径及其相应氧化物的性质决定了两者对TiO2性能的不同影响。     

Fe3+掺杂TiO2薄膜的制备及光催化降解甲醛的研究

采用溶胶-凝胶法制备Fe3+掺杂的TiO2薄膜光催化剂,进行甲醛的光催化实验,考察Fe3+掺杂量、薄膜焙烧温度及溶胶体系pH值对光催化性能的影响。结果表明,Fe3+掺杂量为1.0%,焙烧温度500℃1h,加硝酸溶胶体系pH=4时,Fe3+掺杂TiO2薄膜光催化活性最高。     

低量Gd~3+掺杂TiO_2粉体的制备及催化活性

利用溶胶-凝胶法在700℃制备了纯的和不同Gd3+掺杂量的TiO2纳米粉体,并用XRD技术对样品进行了表征。研究了Gd3+掺杂量对样品相结构、晶粒尺寸和光催化降解亚甲基蓝的活性的影响,利用相结构与纳米TiO2光催化活性关系探讨了Gd3+掺杂对纳米TiO2的光催化活性。结果表明,与纯TiO2相比,适量掺杂Gd3+可以显著提高其光催化活性。当Gd3+掺杂量为0.2%(质量),TiO2复合纳米粉体的光催化活性最佳,降解率为86%,其金红石相含量为15.4%,平均晶粒粒径为15nm;Gd3+掺杂强烈地抑制TiO2由锐钛矿相向金红石相的转变、减小晶粒尺寸和晶格膨胀程度这三方面均有利于提高光催化活性。     

Fe~(3+)/TiO_2薄膜光催化降解UDMH废水的研究

研究Fe3+掺杂的TiO2薄膜对偏二甲肼废水光催化降解作用,考察了影响Fe3+掺杂的TiO2薄膜光催化降解偏二甲肼废水的效果的相关因素,结果表明最佳操作条件为:Fe3+掺杂TiO2薄膜的摩尔分数为0.5%,煅烧温度为500℃,煅烧时间为3h,催化降解反应时偏二甲肼废水为中性或弱碱性,催化降解温度为25℃。     

B/Y~(3+)共掺杂纳米TiO_2催化剂的制备及其降解甲醛的光催化性能评价

为了提高室内环境空气质量,本论文开展了光催化剂制备的研究。本论文采用溶胶-凝胶法制备B/Y3+共掺杂TiO2复合光催化材料,以甲醛为降解物质,在紫外和可见光下分别研究了复合催化剂的光催化活性,对不同掺杂对光催化活性的影响、光催化剂的稳定性进行了分析。B/Y3+共掺杂TiO2复合光催化材料大大提高了催化剂的活性,对甲醛降解有较高的效率。     

Fe3+、Ce3+掺杂TiO2光催化降解气相二苯并呋喃

以气相二苯并呋喃为研究对象,考察了在TiO2、Ce3+/TiO2和Fe3+/TiO2 3种不同光催化剂作用下,反应物初始浓度、湿度、气体循环速率和光强等因素对间歇式光催化反应速率的影响,并建立了估算和测定二苯并呋喃光催化反应常数和Langmuir吸附常数的数学模型和方法.结果表明,Fe3+和Ce3+掺杂修饰TiO2光催化剂后,提高了对二苯并呋喃的光催化降解活性,其中Fe3+/TiO2光催化活性最高;随着二苯并呋喃初始浓度的增大,其光催化降解速率也随之增大;适量的水蒸气存在可以促进二苯并呋喃的降解,但当水蒸气过量后,反而阻碍二苯并呋喃光催化降解;随着气体循环速率加快和光强的增大,二苯并呋喃光催化降解初始速率也随之增大;TiO2、Ce3+/TiO2和Fe3+/TiO2光催化降解二苯并呋喃反应速率常数k分别为34.54×10-5、36.23×10-5和37.95×10-4mg.(min.m2)-1.     

Al3+离子掺杂对负载TiO2薄膜光催化活性的影响

以钛酸丁酯和Al2(SO4)3·18H2O为原料,采用溶胶凝胶法在钛片、玻璃、釉面瓷砖、陶瓷、不锈钢和铝片六种载体上制备了Al3+掺杂TiO2薄膜,讨论了不同Al3+掺杂浓度下,不同载体表面上制备的TiO2薄膜对甲基橙脱色率的影响。试验结果表明Al3+对TiO2薄膜的掺杂效果与载体的类型密切相关,并且不同载体其Al3+掺杂的最佳浓度也不同。Al3+掺杂后,TiO2薄膜光催化活性提高最大的是玻璃,其次是釉面瓷砖、铝片、钛片、陶瓷,最差的是负载不锈钢。     

Fe~(3+)-TiO_2/AC光催化剂的制备及其光催化性能

以活性炭(AC)为载体,通过溶胶-凝胶法制备了Fe3+离子掺杂的TiO2/活性炭(Fe3+-TiO2/AC)负载型光催化剂,通过SEM、XRD、UV-Vis等手段对光催化剂进行了表征。以125W高压汞灯作为光源,通过对罗丹明B的光降解反应,主要考察了温度对Fe3+-TiO2/AC复合体的光催化活性的影响。结果表明,温度在600℃条件下焙烧的Fe3(+0.15%)-TiO2/AC具有最好的光催化活性。     

Cr3+掺杂对TiO2薄膜光催化活性的影响

采用溶胶-凝胶法制备了TiO2粉末和以釉面瓷砖为载体的TiO2薄膜,讨论了不同Cr3+掺杂浓度对TiO2光催化活性的影响,并采用UVVIS对其光学性能进行了检测.结果表明,Cr3+掺杂和釉面瓷砖的交互作用能够显著提高TiO2薄膜的光催化活性,最佳掺杂浓度为6.04×1017个·cm-3,且随着TiO2光催化活性的提高,薄膜的吸收带边发生了明显的红移,提高了可见光的利用率.     

ZnFe_2O_4/TiO_2光催化剂制备及乙酰甲胺磷降解性能研究

分别采用共沉淀法和溶胶-凝胶法制备了ZnFe2O4和掺杂ZnFe2O4的纳米级TiO2光催化剂,进行了XRD、TEM和UV visDRS表征,以卤素灯为光源对纳米TiO2降解水溶液中乙酰甲胺磷农药进行了研究。考察了反应液初始pH值、催化剂用量、H2O2用量对降解率的影响。实验结果表明,焙烧温度为400℃、掺杂量为0.5%的ZnFe2O4/TiO2纳米粉体降解效果最佳,在相同条件下,反应2h后农药降解率可比纯TiO2提高20%左右。正交实验优化了降解反应条件,在常温常压下,起始pH值为12、H2O2浓度为12mmol/L、催化剂浓度为0.5g/L、反应3h后,初始浓度为1.0×10-4mol/L的乙酰甲胺磷农药降解率可达61.2%。     

Effect of crystalline structure on terbuthylazine degradation by H2O2-assisted TiO2 photocatalysis under visible irradiation

Various methods for shifting the optical response of TiO₂ into the visible (Vis) range have been reported. Herein, we reported the application of a TiO₂/H₂O₂/Vis process and the effects of TiO2 crystalline structure on the degradation of terbuthylazine. The results indicated that TiO₂ crystalline structure and H₂O₂ addition had significant effects on terbuthylazine degradation: its degradation rate could be increased from 7% to 70% with H₂O₂ addition after 180?min of reaction, the synergistic degradation of terbuthylazine by TiO₂-Fe^{3 +} was substantially accelerated, with the degradation rate reaching up to 100% after 20?min of reaction, and rutile TiO₂ showed better photocatalytic activity and a more obvious synergistic effect than anatase TiO₂. The addition of free-radical scavengers (tert-butyl alcohol or methanol) inhibited the degradation efficiency of rutile TiO₂, but had a relatively minor effect on anatase TiO₂. Fluorescence spectrophotometry analysis indicated that hydroxyl free radicals could be continuously produced when using rutile TiO₂ as the photocatalyst. Degradation of terbuthylazine catalyzed by rutile TiO₂ occurred mainly in solution, but occurred on the particle surface of the photocatalyst when catalyzed by anatase TiO₂. This study provides new insight into the role of TiO₂ crystalline structure on the degradation of terbuthylazine and its photocatalytic degradation mechanism.     

稀土元素掺杂二氧化钛催化剂光降解久效磷的研究

采用浸渍法制备稀土掺杂二氧化钛光催化剂，通过光催化降解农药久效磷的研究，发现掺杂稀土元素对ＴｉＯ２的光催化性能有明显的影响，特别是Ｃｅ＾４＋、Ｌａ＾３＋等能明显提高ＴｉＯ２的光催活性，并讨论了催化剂的制备，光降解条件诸因素对光降解久效磷的影响。     

掺入金属离子的TiO2纳米粒子光催化降解吖啶橙

利用酸催化溶胶－凝胶法（ｓｏｌ－ｇｅｌ）制备了 Ｆｅ３＋和 Ｃｒ３＋不同掺入量的 ＴｉＯ２半导体纳米粒子研究了这些纳米粒子对吖啶橙光催化氧化降解的影响．结果表明，微量 Ｆｅ３＋和 Ｃｒ３＋的掺入可明显提高 ＴｉＯ２的光催化活性．进一步研究表明，在 Ｆｅ３＋－ＴｉＯ２体系中，最佳掺入量为 ０．１％，而且中性介质和自然光有利于光催化氧化反应的进行，反应３ｈ后降解率可达９７．７５％．在Ｃｒ３＋－ＴｉＯ２体系中，弱碱性介质和自然光有利于光催化氧化反应，最佳掺入量为０．０５％，降解率可达８７．５４％．     

Charge transfer between biogenic jarosite derived Fe~(3+) and TiO_2 enhances visible light photocatalytic activity of TiO_2

In this work, we have shown that mining waste derived Fe~(3+)can be used to enhance the photocatalytic activity of TiO_2. This will allow us to harness a waste product from the mines, and utilize it to enhance TiO_2 photocatalytic waste water treatment efficiency. An organic linker mediated route was utilized to create a composite of TiO_2 and biogenic jarosite. Evidence of Fe\O\Ti bonding in the TiO_2/jarosite composite was apparent from the FTIR, EFTEM, EELS and ELNEFS analysis. The as prepared material showed enhanced photocatalytic activity compared to pristine TiO_2, biogenic jarosite and mechanically mixed sample of jarosite and TiO_2 under both simulated and natural solar irradiation. The prepared material can reduce the electrical energy consumption by 4 times compared to pristine P25 for degradation of organic pollutant in water. The material also showed good recyclability. Results obtained from sedimentation experiments showed that the larger sized jarosite material provided the surface to TiO_2 nanoparticles, which increases the settling rate of the materials. This allowed simple and efficient recovery of the catalyst from the reaction system after completion of photocatalysis. Enhanced photocatalytic activity of the composite material was due to effective charge transfer between TiO_2 and jarosite derived Fe~(3+)as was shown from the EELS and ELNEFS. Generation of OHU was supported by photoluminesence(PL) experiments.     

UV/TiO_2/H_2O_2法对高浓度有机废水降解的应用研究

用UV TiO2 H2 O2 法对高浓度有机废水降解的实验表明 ,当TiO2 、H2 O2 的投加量分别为 2 0g与 1% ,反应时间为3h时 ,CODCr、Oil、Ar OH、NH3 N、S2 - 的平均去除率分别达到 73 %、83 %、86%、5 0 %、10 0 %。此处理工艺具有除臭、除色、快速高效、不产生污泥等优势。实验过程探索了TiO2 、H2 O2 的用量对各污染物降解率的影响 ,并设计了有实用意义的反应器     

凹凸棒石负载TiO_2光催化降解染料的试验研究

以20W紫外灯为光源,研究了将TiO2负载在凹凸棒石上,对染料水样进行光催化降解。由试验得出光催化反应过程中的工艺条件,在此基础上添加H2O2、Fe3+,反应1h后;染料脱色率达95%以上。     

Ag/TiO2光催化降解H酸的研究

采用光化学沉积法制备了Ag TiO2 光催化剂 ,并对典型难生物降解的有机污染物H酸进行了光催化降解研究。结果表明 ,质量分数 1 0 %担载量的Ag能显著提高TiO2 光催化活性 ,可在较短时间内实现对H酸较高的降解效率     

Fulvic acid removal by nanoparticle TiO2 using a submerged membrane photocatalysis reactor

The degradation of fulvic acid（FA） by nanoparticle TiO2 in a submerged membrane photocatalysis（SMPC） reactor was studied. In this reactor, photocatalytic oxidation and membrane separation co-occured. The continuous air supplier provided O2 for the photocatalytical reaction and mixed the solution through an airflow controller. The particle TiO2 could automatically settle due to gravity without particle agglomeration so it could be easily separated by microfiltration（MF） membrane. It was efficient to maintain high flux of membranes. The effects of operational parameters on the photocatalytic oxidation rate of FA were investigated. Results indicated that photocatalyst at 0.5 g/L and airflow at 0.06 m^3/h were the optimum condition for the removal of fulvic acid, the removal efficiency was higher in acid media than that in alkaline media. The effects of different filtration duration on permeate flux rate of MF with P25 powder and with nanoparticle TiO2 were compared. Experimental results indicated that the permeate flux rate of MF was improved and the membrane fouling phenomenon was reduced with the addition of nanoparticle TiO2 catalyst compared with conventional P25 powder. Therefore, this submerged membrane photocatalysis reactor can faciliate potential application of photocatalytic oxidation process in drinking water treatment.