Removal of perchlorate from contaminated waters using surfactant-modified zeolite

We investigated the potential of using surfactant (hexadecyltrimethylammonium)-modified zeolite (SMZ) as an inexpensive sorbent for removing perchlorate (ClO(4)(-)) from contaminated waters in the presence of competing anions. In batch systems, the presence of 10 mM OH(-) (i.e., pH 12), CO(3)(2-), Cl(-), or SO(4)(2-) had little effect on the sorption of ClO(4)(-) by SMZ, indicating that the sorption of ClO(4)(-) by SMZ was very selective. The presence of 10 mM NO(3)(-), however, reduced the sorption of ClO(4)(-) at low initial concentrations. The maximum sorption capacity for ClO(4)(-) by the SMZ remained relatively constant (40-47 mmol kg(-1)), in the absence or presence of the competing ions. In flow-through systems, ClO(4)(-) broke through the SMZ columns much later than other anions present in an artificial ground water. The affinity of the anions for SMZ followed the sequence of ClO(4)(-) > > NO(3)(-) > SO(4)(2-) > Cl(-). Perchlorate loading under dynamic flow-through conditions was 34 mmol kg(-1), somewhat less than the maximum loading of 40 to 47 mmol kg(-1) determined by the batch method. Less than 1% of previously sorbed ClO(4)(-) was leached out by ultra-pure water, by extraction fluid #1 of the standard toxicity characteristic leaching procedure (TCLP), or by a solution of 0.28 M Na(2)CO(3)/0.5 M NaOH. About 40% of the previously sorbed ClO(4)(-) was leached out from SMZ by a 0.5 M NO(3)(-) solution. The exchange of ClO(4)(-) with NO(3)(-) corroborated results of the batch tests where NO(3)(-) was shown to compete with ClO(4)(-) sorption.     

Sorption and fractionation of dissolved organic matter and associated phosphorus in agricultural soil

Mobility of dissolved organic matter (DOM) strongly affects the export of nitrogen (N) and phosphorus (P) from soils to surface waters. To study the sorption and mobility of dissolved organic C and P (DOC, DOP) in soil, the pH-dependent sorption of DOM to samples from Ap, EB, and Bt horizons from a Danish agricultural Humic Hapludult was investigated and a kinetic model applicable in field-scale models tested. Sorption experiments of 1 to 72 h duration were conducted at two pH levels (pH 5.0 and 7.0) and six initial DOC concentrations (0-4.7 mmol L(-1)). Most sorption/desorption occurred during the first few hours. Dissolved organic carbon and DOP sorption decreased strongly with increased pH and desorption dominated at pH 7, especially for DOC. Due to fractionation during DOM sorption/desorption at DOC concentrations up to 2 mmol L(-1), the solution fraction of DOM was enriched in P indicating preferred leaching of DOP. The kinetics of sorption was expressed as a function of how far the solution DOC or DOP concentrations deviate from "equilibrium." The model was able to simulate the kinetics of DOC and DOP sorption/desorption at all concentrations investigated and at both pH levels making it useful for incorporation in field-scale models for quantifying DOC and DOP dynamics.     

Influence of quaternary ammonium on sorption of selected metal cations onto clinoptilolite zeolite

Clay minerals and zeolites have large cation exchange capacities, which enable them to be modified by cationic surfactant to enhance their sorption of organic and anionic contaminants. In this study, the influence of quaternary ammonium surfactants on sorption of five metal cations (Cs+, Sr+, La3+, Pb2+, and Zn2+) onto a clinoptilolite zeolite was investigated. Generally, the metal cation sorption capacity and affinity for the zeolite decreased, indicating that presorbed cationic surfactants blocked sorption sites for metal cations, as the surfactant loading on the zeolite increased. Cesium and Pb2+ sorption was affected to a small extent, indicating that selective sorption for Cs+ and specific sorption for Pb2+ play an important role in addition to cation exchange. Sorption of cationic surfactants on zeolite preloaded with different metal cations showed a strong correlation with the chain length of the surfactant tail group, while the roles of the charges and types of the metal cations were minimal. As the chain length increases, the critical micelle concentration decreases and the surfactant molecules become more hydrophobic, resulting in progressive bilayer coverage. Desorption of presorbed metal cations by cationic surfactants was strongly affected by the surfactant chain length and metal type. More metal cations, particularly Sr2+ and Zn2+, desorbed with an increase in surfactant chain length. The results, in combination with those from organic and oxyanion sorption on surfactant-modified zeolite, may be used for future surfactant modification to target sorption and desorption of a specific type of contaminant or a mixture of different types of contaminants.     

Sorption and desorption of naphthalene by soil organic matter: importance of aromatic and aliphatic components

Nonlinear isotherm behavior has been reported for the sorption of hydrophobic organic compounds (HOCs) in soil organic matter (SOM), but the exact mechanisms are unknown. Our objective was to provide insight into the sorption mechanism of HOCs in SOM by studying the sorption-desorption processes of naphthalene in a mineral soil, its humic fractions, and lignin. Additionally, humin and lignin were used for studying the effects of temperature and cosolvent on HOC sorption. All isotherms were nonlinear. The humin and lignin isotherms became more linear at elevated temperatures and with the addition of methanol indicating a condensed to expanded structural phase transition. Isotherm nonlinearity and hysteresis increased in the following order: soil humic acid (HA) < soil < soil humin. Of the samples, aliphatic-rich humin exhibited the largest degree of nonlinearity and had the highest sorption capacity for naphthalene. High nonlinearity and hysteresis in humin were most likely caused by its condensed structure. A novel aliphatic, amorphous condensed conformation is proposed. This conformation can account for both high sorption capacities and increased nonlinearity observed for aliphatic-rich samples and can explain many sorption disparities discussed in the literature. This study clearly illustrates the importance of both aliphatic and aromatic moieties for HOC sorption in SOM.     

Temperature and microbial activity effects on trace element leaching from metalliferous peats

Due to geochemical processes, peat soils often have elevated concentrations of trace elements, which are gradually released following drainage for agriculture. Our objectives were to use incubation temperatures to vary microbial activity in two metalliferous peats (M7 acidic peat and M3 neutral peat) from the Elba, New York region, and to use periodic leaching to assess the extent of trace element release from these soils. Dried soils were mixed with glass beads to maintain aeration, moistened, and incubated at 4, 16, 28, and 37 degrees C in 10-cm-diameter x 8-cm-tall columns. Five incubation-leaching cycles were performed, each consisting of 7.3 d of incubation (28 d for the final cycle) followed by 16 h of leaching with synthetic acid rain at 2.5 mm h(-1). Microbial activity was determined initially and after the final leaching by measuring C mineralization following glucose stimulation. Cumulative respiration results were ranked 28 > 16 > 4 > 37 degrees C, with M7 acidic peat respiration values greater than M3 neutral peat at each temperature. Initial leachate pH levels were between 2 and 4, with acidification less pronounced and shorter-lived for the M3 peat. Leachate S, dissolved organic carbon (DOC), NO3-N, and trace elements declined with successive leachings (rebounding slightly in the final M3 leachate), with concentrations typically greater in the M7 leachate. Elemental losses followed the same general ranking (28 > 16 > 4 > 37 degrees C); losses at 28 degrees C were 15 to 22% for As, Cd, Ni, and Zn from the M7 peat; losses from M3 were comparable only for Cu (1%) and Ni (19%). The correlation of respiration with S, DOC, and trace elements losses indicates that microbial processes mediated the release of trace elements in both peat soils. Neutral M3 peat pH levels limited losses of most analytes.     

Metal immobilization in soils using synthetic zeolites

In situ immobilization of heavy metals in contaminated soils is a technique to improve soil quality. Synthetic zeolites are potentially useful additives to bind heavy metals. This study selected the most effective zeolite in cadmium and zinc binding out of six synthetic zeolites (mordenite-type, faujasite-type, zeolite X, zeolite P, and two zeolites A) and one natural zeolite (clinoptilolite). Zeolite A appeared to have the highest binding capacity between pH 5 and 6.5 and was stable above pH 5.5. The second objective of this study was to investigate the effects of zeolite addition on the dissolved organic matter (DOM) concentration. Since zeolites increase soil pH and bind Ca, their application might lead to dispersion of organic matter. In a batch experiment, the DOM concentration increased by a factor of 5 when the pH increased from 6 to 8 as a result of zeolite A addition. A strong increase in DOM was also found in the leachate of soil columns, particularly in the beginning of the experiment. This resulted in higher metal leaching caused by metal-DOM complexes. In contrast, the free ionic concentration of Cd and Zn strongly decreased after the addition of zeolites, which might explain the reduction in metal uptake observed in plant growth experiments. Pretreatment of zeolites with acid (to prevent a pH increase) or Ca (to coagulate organic matter) suppressed the dispersion of organic matter, but also decreased the metal binding capacity of the zeolites due to competition of protons or Ca.     

Effects of dissolved organic carbon on sorption and mobility of imidacloprid in soil

To evaluate the effects of dissolved organic carbon on sorption and mobility of the insecticide imidacloprid [1-(6-chloro-3-pyridinyl) methyl-N-nitro-2-imidazolidinimine] in soils, adsorption and column experiments were performed by using a typical calcareous soil from southeastern Spain and two different types of dissolved organic carbon, that is, dissolved organic carbon extracts from a commercial peat (DOC-PE) and high-purity tannic acid (DOC-TA). The experiments were carried out from a 0.01 M CaCl2 aqueous medium at 25 degrees C. The results obtained from the sorption experiments show that the presence of both DOC-PE and DOC-TA, over a concentration range of 15 to 100 mg L(-1), produces in all cases a decreasing amount of imidacloprid adsorbed in the soil studied. From the column experiments the retardation coefficients (RC) were calculated for imidacloprid by using either 0.01 M CaCl2 aqueous solution (RC = 2.10), 0.01 M CaCl2 DOC-PE solution (RC = 1.65), or 0.01 M CaCl2 DOC-TA solution (RC = 1.87). The results indicate that mobility of imidacloprid is increased 21.4 and 11.0% in the presence of DOC-PE and DOC-TA solutions, respectively. Dissolved organic carbon reduces imidacloprid sorption by competing with the pesticide molecules for sorption sites on the soil surface, allowing enhanced leaching of imidacloprid and potentially increasing ground water contamination.     

Leachate chemistry of field-weathered spent mushroom substrate

Passive leaching by rainfall and snowmelt is a popular method to treat piles of spent mushroom substrate (SMS) before its reuse. During this field weathering process, leachate percolates into the underlying soils. A field study was conducted to examine the chemistry of SMS leachate and effects of infiltration. Two SMS piles were deposited (90 and 150 cm in height) over a Typic Hapludult and weathered for 24 mo. Leachate was collected biweekly using passive capillary samplers. The SMS leachate contained high concentrations of dissolved organic carbon (DOC; 0.8-11.0 g L(-1)), dissolved organic nitrogen (DON; 0.1-2 g L(-1)), and inorganic salts. The pH, electrical conductivity, and acid neutralizing capacity were 6.6 to 9.0, 21 to 66 ds m(-1), and 10 to 75 mmolc L(-1), respectively. Inorganic chemistry of the leachate was dominated by K+, Cl-, and SO24-. Leachate DOC was predominantly low molecular weight (<1000 Da) organic acids. During 2 yr of weathering, the 90-cm SMS pile released (per cubic meter of SMS) 3.0 kg of DOC, 1.6 kg of dissolved N, and 26.6 kg of inorganic salts. The 150-cm pile released (per cubic meter of SMS) 2.8 kg of DOC, 0.7 kg of dissolved N, and 13.6 kg of inorganic salts. The 150 cm pile retained more water and exhibited lower net nitrification compared with the 90-cm pile. The top 90 cm of soil retained 20 to 89% of the leachate solutes. Weathering of SMS in piles of 90 cm depth or greater may adversely affect ground water quality.     

Phosphorus leaching at cold temperatures as affected by wastewater application and soil phosphorus levels

Land application of wastewater in the northern-tier United States during winter months has been suggested as a means to reduce cost of building storage lagoons. A study was initiated in 1996 to assess land application of potato-processing wastewater on a 120-ha field at Park Rapids, MN. One objective of this study was to evaluate the effects of soil P levels and temperature on P leaching in soil columns. In this paper, we report the P sorption, desorption, and leaching characteristics of a high-P (>200 mg kg(-1)) and a low-P (<25 mg kg(-1)) surface soil from the wastewater irrigation site. The leaching experiment was done with wastewater at 4 +/- 2 or 10 +/- 2 degrees C. The high-P soil resulted in an equilibrium P concentration of 8.0 mg L(-1) compared with 0.14 mg L(-1) for the low-P soil. When low-P wastewater was applied to the high-P soil, the soil acted as a P source, and the total phosphorus (TP) concentration in the leachate was 3.5 times higher than the input TP concentration (C0). When high-P wastewater was applied to the high-P soil, the soil acted as a P sink retarding the TP concentration in the leachate by 80%. Phosphorus desorption was higher at 10 degrees C compared with 4 degrees C. The results showed that depending on P levels of the soil and the wastewater, reduction or increase in leachate P will occur below the surface soil. However, further mobility of this P under field conditions will depend on the volume and rate of percolating water as well as the sorption-desorption characteristics of the subsoil.     

The effects of leachate recirculation with supplemental water addition on methane production and waste decomposition in a simulated tropical landfill

In order to increase methane production efficiency, leachate recirculation is applied in landfills to increase moisture content and circulate organic matter back into the landfill cell. In the case of tropical landfills, where high temperature and evaporation occurs, leachate recirculation may not be enough to maintain the moisture content, therefore supplemental water addition into the cell is an option that could help stabilize moisture levels as well as stimulate biological activity. The objectives of this study were to determine the effects of leachate recirculation and supplemental water addition on municipal solid waste decomposition and methane production in three anaerobic digestion reactors. Anaerobic digestion with leachate recirculation and supplemental water addition showed the highest performance in terms of cumulative methane production and the stabilization period time required. It produced an accumulated methane production of 54.87 l/kg dry weight of MSW at an average rate of 0.58 l/kg dry weight/d and reached the stabilization phase on day 180. The leachate recirculation reactor provided 17.04 l/kg dry weight at a rate of 0.14l/kg dry weight/d and reached the stabilization phase on day 290. The control reactor provided 9.02 l/kg dry weight at a rate of 0.10 l/kg dry weight/d, and reached the stabilization phase on day 270. Increasing the organic loading rate (OLR) after the waste had reached the stabilization phase made it possible to increase the methane content of the gas, the methane production rate, and the COD removal. Comparison of the reactors' efficiencies at maximum OLR (5 kgCOD/m(3)/d) in terms of the methane production rate showed that the reactor using leachate recirculation with supplemental water addition still gave the highest performance (1.56 l/kg dry weight/d), whereas the leachate recirculation reactor and the control reactor provided 0.69 l/kg dry weight/d and 0.43 l/kg dry weight/d, respectively. However, when considering methane composition (average 63.09%) and COD removal (average 90.60%), slight differences were found among these three reactors.     

Chemistry of inorganic arsenic in soils: II. Effect of phosphorus, sodium, and calcium on arsenic sorption

There are more than 10000 arsenic (As) contaminated sites in Australia. The ability of soils at these contaminated sites to sorb As is highly variable and appreciable amounts of As have been recorded in the subsurface soils. The potential risk of surface and ground water contamination by As at these sites is a major environmental concern. Factors that influence adsorption capacity of soils influence the bioavailability and subsequent mobility of As in soils. In the present study we investigated the effect of PO4(3-) and Na+ and Ca2+ on the sorption of AsV and AsIII by an Oxisol, a Vertisol, and two Alfisols. The presence of P (0.16 mmol L(-1)) greatly decreased AsV sorption by soils containing low amounts of Fe oxides (<100 mmol kg(-1)), indicating competitive adsorption between P and AsV for sorption sites. In contrast, the presence of a similar amount of P had little effect on the amount of AsV adsorbed by soils with high Fe content (>800 mmol kg(-1)). However, AsV sorption substantially decreased from 0.63 to 0.37 mmol kg(-1) as P concentration was increased from 0.16 to 3.2 mmol L(-1) in selected soils. This suggests increased competition between P and AsV for soil sorption sites, through either the higher affinity or the effect of mass action of the increasing concentration of P in solution. A similar effect of P on AsIII sorption was observed in the low sorbing Alfisol and high affinity Oxisol. However, the amount of AsIII sorbed by the Oxisol was much greater than the Alfisol for all treatments. The presence of Ca2+ increased the amount of AsV sorbed compared with that of Na+ and was manifested through changes in the surface charge characteristics of the soils. A similar trend in AsIII sorption was recorded with changes in index cation, although the effect was not as marked as recorded for AsV.     

Chicken manure biochar as liming and nutrient source for acid Appalachian soil

Acid weathered soils often require lime and fertilizer application to overcome nutrient deficiencies and metal toxicity to increase soil productivity. Slow-pyrolysis chicken manure biochars, produced at 350 and 700°C with and without subsequent steam activation, were evaluated in an incubation study as soil amendments for a representative acid and highly weathered soil from Appalachia. Biochars were mixed at 5, 10, 20, and 40 g kg into a Gilpin soil (fine-loamy, mixed, active, mesic Typic Hapludult) and incubated in a climate-controlled chamber for 8 wk, along with a nonamended control and soil amended with agronomic dolomitic lime (AgLime). At the end of the incubation, soil pH, nutrient availability (by Mehlich-3 and ammonium bicarbonate diethylene triamine pentaacetic acid [AB-DTPA] extractions), and soil leachate composition were evaluated. Biochar effect on soil pH was process- and rate-dependent. Biochar increased soil pH from 4.8 to 6.6 at the high application rate (40 g kg), but was less effective than AgLime. Biochar produced at 350°C without activation had the least effect on soil pH. Biochar increased soil Mehlich-3 extractable micro- and macronutrients. On the basis of unit element applied, increase in pyrolysis temperature and biochar activation decreased availability of K, P, and S compared to nonactivated biochar produced at 350°C. Activated biochars reduced AB-DTPA extractable Al and Cd more than AgLime. Biochar did not increase NO in leachate, but increased dissolved organic carbon, total N and P, PO, SO, and K at high application rate (40 g kg). Risks of elevated levels of dissolved P may limit chicken manure biochar application rate. Applied at low rates, these biochars provide added nutritional value with low adverse impact on leachate composition.     

A comparative study for the sorption of Cd(II) by K-feldspar and sepiolite as soil components, and the recovery of Cd(II) using rhamnolipid biosurfactant

This study investigated the sorption characteristics and recovery of selected heavy metal Cd(II) from K-feldspar and sepiolite, representative soil components, using rhamnolipid biosurfactant. Although the proposed technique was classified as a soil bioremediation process, it can also be applied to treatment of waste waters containing Cd(II) ions with minor modifications. The effect of initial Cd(II) concentration on sorption capacity was characterized by determining the sorption isotherms. Of the four models examined, the Freundlich model showed the best fit for the sorption of Cd(II) on K-feldspar, whereas the Langmuir-model was used successfully to characterize the sorption of Cd(II) on sepiolite. Although a high Cd(II) uptake of 7.49 mmol/kg by K-feldspar was obtained, sepiolite was a superior Cd(II) accumulater, with a maximum Cd(II) uptake of 24.66 mmol Cd(II)/kg. The presence of Cd(II) in the sepiolite or K-feldspar prior to addition of the rhamnolipid generally resulted in less rhamnolipid sorption to sepiolite or K-feldspar. The maximum Cd(II) desorption efficiency by rhamnolipid from K-feldspar was substantially higher than that of sepiolite and determined to be 96% of the sorbed Cd(II), whereas only 10.1% of the sorbed Cd(II) from sepiolite was recovered by rhamnolipid solution.     

Phosphorus and nitrogen sorption to soils in the presence of poultry litter-derived dissolved organic matter

Two environmental aspects associated with land application of poultry litter that have not been comprehensively evaluated are (i) the competition of dissolved organic matter (DOM) and P for soil sorption sites, and (ii) the sorption of dissolved organic nitrogen (DON) relative to inorganic nitrogen species (e.g., NO(3)(-) and NH(4)(+)) and dissolved organic carbon (DOC). The competition between DOM and P for sorption sites has often been assumed to increase the amount of P available for plant growth; however, elevating DOM concentrations may also increase P available for transport to water resources. Batch sorption experiments were conducted to (i) evaluate soil properties governing P sorption to benchmark soils of Southwestern Missouri, (ii) elucidate the impact of poultry litter-derived DOM on P sorption, and (iii) investigate DON retention relative to inorganic N species and DOC. Soils were reacted for 24 h with inorganic P (0-60 mg L(-1)) in the presence and absence of DOM (145 mg C L(-1)) using a background electrolyte solution comparable to DOM extracts (I = 10.8 mmol L(-1); pH 7.7). Soil P sorption was positively correlated with metal oxide (r(2) = 0.70) and clay content (r(2) = 0.79) and negatively correlated with Bray-1 extractable P (r(2) = 0.79). Poultry litter-derived DOM had no significant negative impact on P sorption. Dissolved organic nitrogen was preferentially removed from solution relative to (NO(3)(-)-N + NO(2)(-)-N), NH(4)(+)-N, and DOC. This research indicates that poultry litter-derived DOM is not likely to enhance inorganic P transport which contradicts the assumption that DOM released from organic wastes increases plant-available P when organic amendments and fertilizer P are co-applied. Additionally, this work demonstrates the need to further evaluate the fate and transport of DON in agroecosystem soils receiving poultry litter applications.     

Kerogen in aquifer material and its strong sorption for nonionic organic pollutants

Sorption of organic pollutants by subsurface materials has been found to not only correlate with the total organic carbon (TOC) content, but also depend on the types of soil and sediment organic matter (SOM). Characterization of geochemically heterogeneous SOM is key to elucidating sorption mechanisms and predicting pollutant transport in ground water systems. In this study, kerogen, a nonextractable organic material, was isolated with an acid demineralization procedure from a sandy aquifer material (Borden, Ontario, Canada) having a TOC content of approximately 0.021% (w/w). Petrographical examinations reveal that the kerogen has three major types of macerals including bituminite (Kerogen Type I and II), vitrinite (Type III), and fusinite (Type IV or charred kerogen). The solid-state 13C nuclear magnetic resonance (NMR) spectrum shows two dominant peaks, aliphatic and aromatic carbons, for the isolated material. Sorption isotherms measured using phenanthrene, naphthalene, 1,3,5-trichlorobenzene (TCB), and 1,2-dichlorobenzene (DCB) as sorbates showed that both the isolated kerogen and the original sand exhibited nonlinear sorption and that the phenanthrene and TCB isotherms measured for the kerogen material are more nonlinear than the respective isotherms for the original sand. The single-point organic carbon--normalized sorption capacity measured for the isolated kerogen can be several times greater than that measured for the original sand for a given sorbate. The study suggests that kerogen plays a major role in overall sorption isotherm nonlinearity and could yield higher-than-predicted sorption capacities for the subsurface material even though the content of this organic material is very low.     

Assessment of spent mushroom substrate as sorbent of fungicides: influence of sorbent and sorbate properties

The capacity of spent mushroom substrate (SMS) as a sorbent of fungicides was evaluated for its possible use in regulating pesticide mobility in the environment. The sorption studies involved four different SMS types in terms of nature and treatment and eight fungicides selected as representative compounds from different chemical groups. Nonlinear sorption isotherms were observed for all SMS-fungicide combinations. The highest sorption was obtained by composted SMS from Agaricus bisporus cultivation. A significant negative and positive correlation was obtained between the K(OC) sorption constants and the polarity index values of sorbents and the K(OW) of fungicides, respectively. The statistic revealed that more than 77% of the variability in the K(OW) could be explained considering these properties jointly. The other properties of both the sorbent (total carbon, dissolved organic carbon, or pH) and the sorbate (water solubility) were nonsignificant. The hysteresis values for cyprodinil (log K(OW)= 4) were for all the sorbents much higher (>3) than for other fungicides. This was consistent with the remaining sorption after desorption considered as an indicator of the sorption efficiency of SMS for fungicides. Changes in the absorption bands of fungicides sorbed by SMS observed by FTIR permitted establishing the interaction mechanism of fungicides with SMS. The findings of this work provide evidence for the potential capacity of SMS as a sorbent of fungicides and the low desorption observed especially for some fungicides, although they suggest that more stabilized or humified organic substrates should be produced to enhance their efficiency in environmental applications.     

Temperature and wetland plant species effects on wastewater treatment and root zone oxidation

Constructed wetlands are widely used for wastewater treatment, but there is little information on processes affecting their performance in cold climates, effects of plants on seasonal performance, or plant selection for cold regions. We evaluated the effects of three plant species on seasonal removal of dissolved organic matter (OM) (measured by chemical oxygen demand and dissolved organic carbon) and root zone oxidation status (measured by redox potential [Eh] and sulfate [SO4(2-)]) in subsurface-flow wetland (SSW) microcosms. A series of 20-d incubations of simulated wastewater was conducted during a 28-mo greenhouse study at temperatures from 4 to 24 degrees C. Presence and species of plants strongly affected seasonal differences in OM removal and root zone oxidation. All plants enhanced OM removal compared with unplanted controls, but plant effects and differences among species were much greater at 4 degrees C, during dormancy, than at 24 degrees C, during the growing season. Low temperatures were associated with decreased OM removal in unplanted controls and broadleaf cattail (Typha latifolia L.) microcosms and with increased removal in beaked sedge (Carex rostrata Stokes) and hardstem bulrush [Schoenoplectus acutus (Muhl. ex Bigelow) A. & D. L?ve var. acutus] microcosms. Differences in OM removal corresponded to species' apparent abilities to increase root zone oxygen supply. Sedge and bulrush significantly raised Eh values and SO4(2-) concentrations, particularly at 4 degrees C. These results add to evidence that SSWs can be effective in cold climates and suggest that plant species selection may be especially important to optimizing SSW performance in cold climates.     

Coupled effects of treated effluent irrigation and wetting-drying cycles on transport of triazines through unsaturated soil columns

The physical and chemical parameters controlling the movement of atrazine (6-chloro-N2-ethyl-N4-isopropyl-l,3,5-triazine-2,4-diamine; 98.8%) and prometryn [N,N'-bis(1-methylethyl)-6-(methylthio)-l,3,5triazine-2,4-diamine; 99.5%] were investigated in columns infiltrated with treated effluent under unsaturated transient conditions and subjected to drying events at 22 or 60 degrees C followed by rewetting. Three soils varying in soil pH and texture and three solutions were used. The infiltrating solutions consisted of either a CaCl2 matrix (CC), a swine waste-derived lagoon effluent (SW), or a simulated buffer solution (SB) representative of the element composition and pH of the SW but with no dissolved organic matter. Several parameters were monitored including leachate triazine concentrations, pH, dissolved organic carbon (DOC), inorganic carbon, and flow rates. Compared with CC, application of SW and SB increased column leachate pH, enhanced dissolution of organic carbon and particle dispersion, and decreased average flow rates, which allowed for increased desorption time. The coupled effect of these processes enhanced movement of triazines in some cases, with SW generally having the greatest effect. The individual effect of increased pH was more pronounced for prometryn (pKa=4.05) versus atrazine (pKa=1.66), and most dramatic for the soil with the lowest initial pH. High-temperature drying, which simulated intensive evaporation, further enhanced the dissolution of soil organic matter and the reduction in leachate flow rates with SW and SB applications; however, the net effect under the experimental conditions employed varied with soil type. Relative to low-temperature drying, high-temperature drying in the silty clay loam-packed columns reduced pesticide migration.     

Effect of dissolved organic matter from sludge and sludge compost on soil copper sorption

Interaction of Cu with dissolved organic matter (DOM) is an important physicochemical process affecting Cu mobility in soils. The aim of this study was to investigate the effects of DOM from anaerobically digested dewatered sludge and sludge compost on the sorption of Cu on an acidic sandy loam and a calcareous clay loam. In the presence of DOM, Cu sorption capacity decreased markedly for both soils, especially for the calcareous soil. The Cu sorption isotherms could be well described by the Freundlich equation (r2 = 0.99), and the binding intensity parameter of soils in the presence of sludge DOM was lower than compost DOM. An increase in DOM concentration significantly reduced the sorption of Cu by both soils. Within the Cu and DOM concentration range studied, the decrease in Cu sorption caused by sludge DOM was consistently greater than that of compost DOM. This might be attributed to the greater amount of hydrophobic fraction of DOM in the compost. Moreover, the reduction of Cu sorption caused by DOM was more obvious in the soil with higher pH. In addition, the sorption of Cu increased with an increase in pH for both soils without the addition of DOM, while Cu sorption in the presence of DOM was unexpectedly decreased with an increase in pH at a pH >6.8. This implied that DOM produced by sludge or other C-enriched organic wastes heavily applied on calcareous soils might facilitate the leaching loss of Cu because of the formation of soluble DOM-metal complexes.     

Sorption of the antibiotic tetracycline to humic-mineral complexes

Humic substances, by altering the surface properties and/or competing for available reaction sites, can either suppress or promote sorption of organic compounds to mineral surfaces. Limited literature evidence points to the reduction in sorption of the antibiotic tetracycline to clay minerals in the presence of humic substances. We investigated the surface interaction of Elliott soil humic acid (ESHA) with hydrous Al oxide (HAO) and the effect of this association on tetracycline sorption. Strong interaction between ESHA and HAO led to ESHA-promoted dissolution of HAO and surface charge reversal. The ESHA-HAO sorption-desorption isotherms were successfully described using a modified Langmuir model that accounted for the heterogeneity of HAO surface and ESHA. Ligand exchange was proposed as the major interaction mechanism, and the edge Al atoms on HAO surface were considered as the sorption sites for ESHA macromolecules. ESHA was coated onto HAO to achieve two different organic content (foc) levels of 0.81 and 1.52%. Sorption results were compared for the binary ESHA-tetracycline and HAO-tetracycline systems, and the ternary ESHA-HAO-tetracycline system. The coating of ESHA on HAO significantly suppressed tetracycline sorption levels, attributable to altered HAO surface charge characteristics and/or direct competition between ESHA and tetracycline for potential sorption sites. Higher foc level, besides increasing the extent of sorption suppression, also resulted in greater ionic strength dependence and increased nonlinearity of sorption behavior. It, therefore, appears that the presence of humic substances, in both dissolved and mineral-bound forms, is likely to increase the environmental mobility of tetracycline compounds.