臭氧氧化结合碱液吸收法烟气脱硝的工艺研究

利用臭氧将烟气中溶解度较小的NO氧化成NO2,再结合尿素、氢氧化钠、氢氧化钙溶液吸收脱除臭氧氧化产物,重点考察了O3与NO反应的摩尔比、进口NO浓度、烟气中SO2浓度和相对湿度等工艺参数对NO氧化的影响,并探明不同的吸收液脱除臭氧氧化产物的特性。结果显示O3与NO反应的最佳摩尔比为1.02,随着进口NO浓度的增加氧化效率下降,而烟气中的SO2和相对湿度对NO氧化影响较小。通过对氢氧化钙吸收臭氧氧化产物的特性分析得出,碱液对NO的吸收率相对较小,而对NO2的吸收率达到80%以上。     

Fe3+强化NaClO2溶液脱硝过程研究

以NaClO_2-Fe~(3+)为复合吸收剂,在填料吸收塔中进行了脱硝实验。实验结果表明:Fe~(3+)能够显著提高NaClO_2的氧化活性,1.0 mmol/L NaClO_2溶液加入0.10 mmol/L Fe~(3+)后即可达到5.0 mmol/L NaClO_2溶液不加Fe~(3+)时的脱硝水平;在NaClO_2浓度1.0 mmol/L、Fe~(3+)浓度0.10 mmol/L、吸收液初始pH 3.75、反应温度60 ℃、液气比8 L/m~3的优化工艺条件下处理NO 140 mg/m~3的进气,NO氧化率和NO_x脱除率分别达到92.63%和83.62%。脱硝前后吸收液组成的测定结果表明:起主要脱硝作用的是ClO_2;反应消耗的NaClO_2与NO的摩尔比为1.06。通过补加消耗的NaClO_2可达同样的脱硝效果,循环3次后吸收液中的有效成分基本稳定。     

次氯酸钙溶液的脱硫脱硝特性

采用Ca(ClO)2溶液在高效反应瓶中与模拟烟气进行脱硫脱硝实验,考察了模拟烟气中SO2和NOx的去除效果,以动力学为理论基础研究了Ca(ClO)2的脱硫脱硝性能。实验结果表明:在模拟烟气中SO2,NO,NO2的质量浓度分别为3700,1300,820 mg/m^3及Ca(ClO)2溶液浓度为0.35 mol/L的条件下,SO2去除率达到100%,NOx去除率达到67%。脱硫过程中吸收液中的ClO-是100%脱硫率的保障。Ca^2+吸收SO2的反应速率呈现一级反应的特征。得到的脱硫产物CaSO4·2H2O达到了工业石膏的品质要求。同时脱硫脱硝时NOx和SO2具有协同作用。     

半干法脱除球团烟气中的SO2及Hg0

采用钙基吸收剂及复合氧化剂半干法脱除模拟球团烟气中的SO_2及Hg~0,考察了多因素条件对吸收效果的影响。实验结果表明,在以NaClO和NaClO_2为复合氧化剂、 NaClO与NaClO_2体积比1∶0.5、复合氧化剂质量分数3%、反应温度110℃、钙基吸收剂质量3.0 g、模拟烟气进气流量1.2 L/min的条件下,SO_2和Hg~0的脱除率分别为98%和93%,证明钙基吸收剂与复合氧化剂对污染物球团烟气中的SO_2和Hg~0有良好的脱除作用。     

CeO2/TiO2纳米管催化剂脱硝性能研究

利用废气中本身含有的CO催化还原烟气中的NO_x,可以实现以废治废。采用TiO₂纳米管负载CeO₂,制备CeO₂/TiO₂纳米管催化剂,并对其进行了SEM表征及影响因素实验。实验结果表明：在n（Ce）∶n（Ti）=3∶7、焙烧温度500 ℃、焙烧时间3 h时制备的CeO₂/TiO₂纳米管催化剂形貌较好,表面颗粒分布相对均匀;反应温度400~600 ℃时NO脱除率达98%;该催化剂具有一定的抗氧性能;当n（SO₂）∶n（NO）=（1∶2）~（2∶1）时,NO脱除率仍然在95%以上。     

天然气再燃添加有机酸盐同时降低SO2及NOx的机理研究

对天然气再燃过程中添加的有机酸盐同时脱硫、脱氮反应途径及机理进行了详细的分析.探讨了有机酸盐(钙镁醋酸盐CMA)分解的CHi还原NO的主要机理,研究了CMA固硫的反应机理,分析了脱硫过程影响HCN、NH3还原NO的因素.提出了天然气再燃添加CMA同时脱硫、脱氮时,也要综合考虑CaO对SO2的脱除和对NO生成的促进作用.     

袋式除尘器在国电九江电厂的应用及其对PM2.5的脱除分析

国电九江发电厂“上大压小”扩建工程2 x 660 MW超超临界燃煤机组配套采用旋转式低压脉冲袋式除尘器,对袋式除尘器进出口烟气中PM2.5、SO2、NO、SO3、氯化物、汞等浓度进行了现场测试,结果表明,该袋式除尘器能有效脱除烟气中的PM2.5,其PM2.5数浓度和质量浓度脱除效率可分别高达98.9%和99.7%,同时还可脱除富集在PM2.5表面的颗粒态汞。     

类过氧化物酶Fe-TAML催化H_2O_2脱除烟气中的单质汞

采用有机合成法制备了类过氧化物酶(Fe-TAML)催化剂。利用制备的Fe-TAML催化H_2O_2脱除烟气中的Hg~0,考察了影响Hg~0去除率的多种因素。实验结果表明:在Fe-TAML催化剂用量为0.08 g/L、H_2O_2浓度为0.035mol/L、溶液pH为9、反应温度为40℃、烟气中Hg~0质量浓度为101.00μg/m3的条件下,反应30 min的平均Hg~0去除率可达71.50%。以甲醇作为HO·的淬灭剂开展了淬灭实验,结合产物分析,推测了Hg~0的去除机理。     

CePO4-TiO2固溶体的NH3-SCR活性

采用共沉淀法合成了不同Ce与Ti摩尔比的CePO₄-TiO₂复合材料,利用XRD、TEM、NH₃-TPD和H₂-TPR技术对其物理化学性质进行了表征,并对其NH₃-SCR活性进行了评价。实验结果表明：随着CePO₄含量的增加,催化剂的活性提高;当Ce与Ti的摩尔比为8:2时催化剂的活性最高,230 ℃的NO转化率达到100%,且具有更广的温度窗口,优于纯CePO₄。表征结果显示,CePO₄与TiO₂形成固溶体后,颗粒尺寸较为均匀,强酸位的数量增多,氧化还原性能提升,从而提高了催化剂的SCR反应活性,同时改善了其抗水抗硫性能。     

微纳米气液分散体系氧化脱除天然气汽车尾气中的复合污染物

采用微纳米气液分散体系对天然气汽车尾气中的复合污染物进行氧化脱除.实验结果表明:CH4、NO和SO2的脱除率均随着吸收液中NaCl、十二烷基硫酸钠(SDS)、Fe2+和Mn2+投加量的增加而先升后降,在酸性和碱性条件下均随着pH的增大呈先升后降的趋势;进气CH4、NO、SO2质量浓度为429,267,571 mg/m3...     

Adsorption of SO2 and NO from incineration flue gas onto activated carbon fibers

Activated carbon fibers (ACFs) were used to remove SO(2) and NO from incineration flue gas. Three types of ACFs in their origin state and after pretreatment with HNO(3), NaOH, and KOH were investigated. The removal efficiencies of SO(2) and NO were determined experimentally at defined SO(2) and NO concentrations and at temperatures of 150, 200 and 260 degrees C. Experimental results indicated that the removal efficiencies of SO(2) and NO using the original ACFs were <56% and <27%, respectively. All ACFs modified with HNO(3), NaOH, and KOH solution could increase the removal efficiencies of SO(2) and NO. The mesopore volumes and functional groups of ACFs are important in determining the removal of SO(2) and NO. When the mesopore volumes of the ACFs are insufficient for removing SO(2) and NO, the functional groups on the ACFs are not important in determining the removal of SO(2) and NO. On the contrary, the effects of the functional groups on the removal of SO(2) and NO are more important than the mesopore volumes as the amount of mesopores on the ACFs is sufficient to remove SO(2) and NO. Moreover, the removal efficiencies of SO(2) and NO were greatest at 200 degrees C. When the inlet concentration of SO(2) increased to 600ppm, the removal efficiency of SO(2) increased slightly and the removal efficiency of NO decreased.     

ClO_2溶液去除烟气中NO的效果及工程应用

采用实验室规模喷淋脱硝装置对ClO_2溶液去除NO的效果及影响因素进行探讨,通过脱硝产物的测定对ClO_2溶液去除NO的能力及机理进行分析;在此基础上考察ClO_2溶液对供热厂燃煤锅炉烟气的实际脱硝效果。实验结果表明:在液气比为20L/m~3、反应温度为20℃,反应pH为4.0、进气NO质量浓度为250 mg/m~3,ClO_2质量浓度为200 mg/L的条件下,NO去除率达97%以上;ClO_2溶液可将NO氧化吸收为NO_3~-,氧化后产生的NO_x也可被NaOH溶液吸收转化为NO_2~-和NO_3~-;在ClO_2质量浓度为200~500 mg/L,反应pH为5.5~7.0的条件下处理初始NO质量浓度为212~230 mg/m~3的燃煤锅炉烟气,NO去除率为85.7%~94.6%,NO_x去除率为80.4%~88.8%,出口NO_x质量浓度低于46 mg/m~3,远低于GB 13271—2014规定的排放限值。     

湿法同时脱硫脱硝工艺中脱硝吸收剂的研究现状

综述了目前国内外开发的湿法烟气脱硫、脱硝一体化技术中对脱硝吸收剂的研究现状,主要介绍了亚氯酸钠、过氧化氢、高锰酸钾、亚铁络合物、钴络合物以及尿素、亚硫酸铵。分析了各种吸收剂的优缺点,并对湿法脱硝吸收剂的应用前景进行了展望。     

高效复合型亚铁络合剂同时脱硫脱硝

采用自制喷淋塔进行湿法同时脱硫脱硝实验,在乙二胺四乙酸(EDTA)络合亚铁吸收液及半胱氨酸络合亚铁吸收液的基础上,研制出复合吸收液。实验结果表明:对于单一络合物吸收液,EDTA络合亚铁吸收液的脱硝效果较好,可在70 min内保持60%以上的NO脱除率,而半胱氨酸络合亚铁吸收液则可长时间保持较好的脱硫效果,可在180 min内保持90%以上的SO_2脱除率;复合吸收液的脱硫脱硝性能较单一络合物吸收液有明显提高,在络合物浓度为0.05 mol/L、吸收液pH为8、EDTA与半胱氨酸的摩尔比为1∶2、Fe~(2+)浓度为0.075 mol/L的优化条件下,90 min内的NO脱除率基本保持在70%以上,SO_2脱除率基本达到100%。     

超声吹脱-次氯酸钠氧化工艺处理酮连氮法制肼废水

采用超声吹脱-次氯酸钠氧化工艺处理酮连氮法制肼废水,优化了工艺条件,并进行了尾水处理与盐分回收。实验结果表明:在超声声能密度0.08 W/mL、吹脱气量2 000 L/h、次氯酸钠溶液(有效氯10%)投加量15mL/L、反应时间20 min的最优条件下,COD、氨氮和肼类物质去除率分别达到96.97%、99.02%和96.60%,处理成本约为30元/t(以废水计);尾水经蒸馏处理后可满足GB 8978—1996《污水综合排放标准》的一级B标准,回收NaCl纯度为98.92%,达到GB/T 5462—2015《工业盐》的精制工业盐一级标准。     

用次氯酸钠法处理选矿废水

采用次氯酸钠法处理铅锌硫化矿选矿废水,考察了废水初始pH、NaClO加入量及反应时间对选矿废水COD去除率的影响。在废水pH为4、NaClO加入量为100g/L、反应时间为30min的条件下,选矿废水的COD去除率可达到98．3％;当pH为11、反应时间为10min、NaClO加入量为1g/L时,选矿废水的COD去除率为39．4％。     

A novel additive for the reduction of acid gases and NO(x) in municipal waste incinerator flue gas.

The reduction of SO2, HCl, and NO(x) concentrations using calcium magnesium acetate (CMA) as a novel sorbent in a simulated municipal waste incinerator flue gas was investigated. The reduction of individual SO2, HCl, and NO(x) concentrations was tested at 850 degrees C and it was found that CMA could reduce the SO2 concentration by 74%, HCl concentration by 64%, or NO(x) concentration by 94%. It was observed that individual SO2 or HCl capture increased with increasing initial oxygen concentration in the reacting gas or increasing sorbent input. NO(x) reduction decreased with increasing initial oxygen concentration in the reacting gas. The simultaneous reduction of SO2, HCl, and NO(x) concentrations by CMA was also investigated. It was found that CMA could simultaneously capture 60% SO2 and 61% HCl and reduce NO(x) concentrations by 26%, when the initial oxygen concentration in the reacting gas was 4%. During the simultaneous reduction of SO2, HCl, and NO(x), it was noted that as the initial oxygen concentration in the reacting gas increased, the efficiency of SO2 capture increased too, but the efficiency of HCl capture and the efficiency of NO(x) destruction decreased.     

臭氧氧化—钙法吸收工艺对烟气的同步脱硫脱硝

针对中国石化镇海炼化乙烯动力锅炉烟气的特点,进行烟气模拟,采用臭氧氧化—钙法吸收同时脱硫脱硝工艺处理模拟烟气。实验对比了单独脱硫和脱硝过程与同时脱硫脱硝工艺的脱硫、脱硝效果,探究了烟气在反应器中的停留时间、臭氧投加量和烟气含氧量对SO₂去除率和NO_x去除率的影响。实验结果表明：SO₂和NO的共存可促进污染物的去除;烟气停留时间延长,SO₂去除率提高,NO_x去除率先升高后降低;臭氧与NO摩尔比增加,NO_x去除率提高,SO₂去除率略有降低。综合考虑选择烟气停留时间3.4 s,烟气含氧量12%（φ）,臭氧与NO摩尔比0.7,在此工艺条件下反应70 min,NO_x去除率为73.8%,SO₂去除率为74.1%。     

Supercritical water oxidation of landfill leachate

In this paper, ammonia as an important ingredient in landfill leachate was mainly studied. Based on Peng-Robinson formulations and Gibbs free energy minimization method, the estimation of equilibrium composition and thermodynamic analysis for supercritical water oxidation of ammonia (SCWO) was made. As equilibrium is reached, ammonia could be totally oxidized in SCW. N(2) is the main product, and the formation of NO(2) and NO could be neglected. The investigation on SCWO of landfill leachate was conducted in a batch reactor at temperature of 380-500 °C, reaction time of 50-300s and pressure of 25 MPa. The effect of reaction parameters such as oxidant equivalent ratio, reaction time and temperature were investigated. The results showed that COD and NH(3) conversion improved as temperature, reaction time and oxygen excess increased. Compared to organics, NH(3) is a refractory compound in supercritical water. The conversion of COD and NH(3) were higher in the presence of MnO(2) than that without catalyst. The interaction between reaction temperature and time was analyzed by using response surface method (RSM) and the results showed that its influence on the NH(3) conversion was relatively insignificant in the case without catalyst. A global power-law rate expression was regressed from experimental data to estimate the reaction rate of NH(3). The activation energy with and without catalyst for NH(3) oxidation were 107.07 ± 8.57 kJ/mol and 83.22 ± 15.62 kJ/mol, respectively.