臭氧与TiO2/UV协同降解对氯苯酚

利用O3／UV、TiO2／UV和O3／TiO2／UV降解对氯苯酚表明，臭氧与TiO2／UV具有明显的协同作用，如在本实验条件下降解5min后，上述3者对对氯苯酚的去除率分别为55％、10％和77%。O3／TiO2／UV协同作用的本质是由于臭氧能带走二氧化钛光致电子空穴对中的电子，从而产生了更多的羟基自由基，加速了有机物的降解。     

TiO2光催化复合分离膜对水中天然有机物的去除

在水源污染越来越严重、水质标准日益严格的背景下,超滤（UF）已逐渐成为替代饮用水常规处理技术的最佳选择之一。本研究中采用相转化法,将聚偏氟乙烯（PVDF）、聚乙二醇（PEG）和二氧化钛（TiO2）共混制得光催化复合分离膜并对其进行扫描电子显微镜（SEM）、原子力显微镜（AFM）和X射线能谱仪（EDS）等相应的表征。比较了有无光照条件下,PVDF-PEG和PVDF—PEG—TiO2膜对腐殖酸（HA）的截留和超滤过程中的膜污染情况。研究结果表明,TiO2光催化复合分离膜能提高对水中天然有机物的去除并同时降低膜污染。紫外光照强度越强,PVDF-PEG—TiO2膜的抗污染性能越好。另外,光催化能更有效地减少超滤初始浓度较低的腐殖酸溶液过程中的膜通量衰减。     

N-doped SiO2/TiO2 mesoporous nanoparticles with enhanced photocatalytic activity under visible-light irradiation

Mesoporous nanocrystalline N-doped SiO2/TiO2 visible-light photocatalysts were prepared by treating SiO2/TiO2 xerogels in a flow of nitrogen gas bubbled through concentrated ammonia solution. Structural characterization and performance analysis results revealed that the addition of SiO2 remarkably altered the phase composition, specific surface area, microstructure, as well as the photocatalytic activity of N-doped TiO2. The presence of SiO2 in N-doped TiO2 particles suppressed the formation of rutile phase and the crystal growth of N-doped TiO2 particles during thermal calcinations. When weight ratio of SiO2/TiO2 was in 0.05-0.20, the N-doped SiO2/TiO2 exhibited higher photocatalytic activity than the N-doped TiO2, and optimum ratio was found to be 0.05. The enhanced photocatalytic activity could be attributed to the higher specific area, larger pore volume, and more surface hydroxyl groups in the catalyst.     

Study on the indoor volatile organic compound treatment and performance assessment with TiO2/MCM-41 and TiO2/quartz photoreactor under ultraviolet irradiation

Volatile organic compounds (VOCs) are the cause of indoor air pollution and are readily emitted from furniture and cleaning agents. In Taiwan, the concentrations of indoor VOCs range roughly from 1 to 10 ppm. It is important to effectively reduce indoor VOC emissions and establish the implementation of long-term, low-cost, controlled techniques such as those found in the ultraviolet/titanium dioxide (UV/TiO2) control systems. This study evaluates the performance of a photoreactor activated by visible irradiation and packed with TiO2/quartz or TiO2/mobile catalytic material number 41 (MCM-41). The photocatalysts tested include commercial TiO2 (Degussa P-25) and synthesized TiO2 with a modified sol-gel process. The UV light had a wavelength of 365 nm and contained an 8-W, low-pressure mercury lamp. Reactants and products were analyzed quantitatively by using gas chromatography with a flame-ionization detector. It is important to understand the influence of such operational parameters, such as concentration of pollutant, temperature, and retention time of processing. The indoor concentrations of VOCs varied from 2 to 10 ppm. Additionally, the temperatures ranged from 15 to 35 degrees C and the retention time tested from 2 to 8.2 sec. The results show that quartz with TiO2 had a better photoreductive efficiency than quartz with MCM-41. The toluene degradation efficiency of 77.4% with UV/TiO2/quartz was larger than that of 54.4% with the UV/TiO2/MCM-41 system under 10-min reaction time. The degradation efficiency of the UV/TiO2 system decreased with the increasing concentrations of indoor VOCs. The toluene degradation efficiency at 2 ppm was approximately 5 times greater than that at 10 ppm. The photoreduction rate of the VOCs was also evaluated with the Langmuir-Hinshewood model and was shown to be pseudo-first-order kinetics.     

Dissolution studies on TiO2 with organics

In this work the effect of organic reducing reagents, namely, ascorbic acid, oxalic acid and L-cysteine on dissolution of commercial TiO(2) has been investigated. Kinetic studies showed that a maximum of about 45% of TiO(2) was dissolved by ascorbic acid in 4h when oxide:acid molar ratio was kept at 1:2. The dissolution of TiO(2) increased with increase in ascorbic acid and oxalic acid concentration up to 0.15M in 4h (corresponding to molar ratio of oxide to acid of 1:3) and further addition did not affect the dissolution. Nearly 45% TiO(2) dissolution was obtained with ascorbic acid alone while oxalic acid yielded 40% dissolution. When oxalic acid was added along with ascorbic acid in equi-molar concentrations, dissolution of TiO(2) was enhanced to 60% in 2.5h but when cysteine was added to ascorbic acid the dissolution was about 50% in just 1h.     

TiO_2微球光催化降解腐植酸钠

以阳离子交换树脂为模板,采用溶胶-凝胶法以四氯化钛为原料制备TiO2微球,采用XRD,FTIR,SEM对样品进行了表征。微球中主要组分是锐钛矿型TiO2,同时掺杂有少量Na＋,SO24-等离子,比TiO2粉末具有更好的光催化性能,具备重复使用的能力,使用寿命较长,可作为一种有实用价值的光催化剂。在300 W高压汞灯下采用二氧化钛微球催化降解腐植酸钠,分析了催化剂投加量和反应时间对降解率的影响。腐植酸钠的光催化降解实验结果表明：初始浓度为10 mg/L的腐植酸钠在碱性条件,催化剂投加量为2.5 g/L,反应时间为3 h时最为适宜,最大降解率可达到96.51%。     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

Ba/TiO_2/MCM-41光催化降解对硝基苯甲酸

以钛酸丁酯为钛源、MCM-41分子筛为载体,采用溶胶-凝胶法制备了掺杂与负载相结合的光催化剂Ba/TiO2/MCM-41。结果表明：Ba/TiO2/MCM-41是一种比表面积高达341.2 m2/g的介孔材料,主要晶相为锐钛矿相,比P25有更强的紫外光吸收。将Ba/TiO2/MCM-41用于光催化氧化水中的对硝基苯甲酸,当催化剂投加量为0.5 g/L,对硝基苯甲酸初始pH为4、浓度为2×10-4mol/L时,紫外光照30 min后,对硝基苯甲酸降解率达到96.0%。用紫外光谱、红外光谱和高效液相色谱分析对硝基苯甲酸降解前后的变化,发现随着光照时间延长,苯环上的硝基、羧基吸收峰逐渐减弱;对硝基苯甲酸首先被降解为一些中间小分子产物,随着反应进行,小分子物质也逐渐被降解。     

Decolorizing of lignin wastewater using the photochemical UV/TiO2 process

Studies on applying the photochemical UV/TiO2 oxidation process to treat the lignin-containing wastewater for dissolved organic carbon (DOC), color and reducing A254 (the absorption at the wavelength of 254 nm) have been carried out. The data obtained in this study demonstrate that the UV/TiO2 process is effective in oxidizing the lignin thus reducing the color and DOC of the wastewater treated. The combined UV/TiO2 treatment can achieve better removal of DOC and color than the UV treatment alone. Color removal, based on American Dye Manufacture Index (ADMI) measurement, is greater than 99% if the pH is maintained at 3.0 with the addition of 1 g l(-1) TiO2. When 10 g l(-1) TiO2 is applied, the oxidation reduction potential (ORP) value is reached to result in an 88% removal of both DOC and color. A model was developed based on the variation of ORP during the photochemical reaction to simulate the decoloring process. The proposed model can be used to predict the color removal efficiency of the UV/TiO2 process.     

Photocatalytic reactions of pyrene at TiO2/water interfaces

The photocatalytic oxidation of pyrene preadsorbed on TiO2 is examined in aqueous suspension under UV irradiation. Chemical oxygen demand measurements, UV-VIS spectrophotometer, infrared spectrometer and GC-MS analytical techniques were used to monitor the formed intermediates. During the oxidation processes, the ring-open reaction, hydroxylation and ketolysis occurred to produce some intermediate products (4-oxapyrene-5-one, 1,6- or 1,8-pyrenediones, 4,5-phenanthrenedialdehyde, cyclopenta[def]phenanthrene). Some factors affecting the photodegradation rate were also studied. The results were different from other studies: The pH of the dispersion, ratio of Py/TiO2:water had little effect on the photooxidation rate of pyrene catalyzed by TiO2, while the surface coverage, addition of Fe3+ affected it greatly.     

The effects of manganese precursors on Mn-based/TiO2 catalysts for catalytic reduction of NO with NH3

Manganese acetate (MnAc) and manganese nitrate (MnN) were employed as precursors for the preparation of MnAc)/TiO2, Mn (N)/TiO2, Mn(Ac)-Ce/TiO2, and Mn(N)-Ce/TiO2 by impregnation. These complexes were used as catalysts in the low-temperature selective catalytic reduction of NO with NH3. The influence of manganese precursors on catalyst characteristics, the reduction activity, and the stability of the catalysts to poisoning by H2O and SO2 were studied. Experiments showed that Mn(N) produced MnO2 with large grain sizes in Mn(N)/TiO2 catalyst. On the contrary, Mn(Ac) led to highly dispersed and amorphous Mn2O3 in Mn (Ac)/TiO2 catalyst, which had better catalytic activity and stability to SO2 at low temperatures. The doping of cerium reduced the differences in catalytic performance between the catalysts derived from different Mn precursors.     

Degradation of short-chain alkyl- and alkanolamines by TiO2- and Pt/TiO2-assisted photocatalysis

The photooxidation of C2H5NH2, (C2H5)2NH, HOC2H4NH2, (HOC2H4)2NH and (HOC2H4)3N using TiO2 and Pt/TiO2 as photocatalysts has been investigated. A laboratory set up was designed and a study on the influence of the concentration of the photocatalyst, the pH-value and the structure of the amine performed. The photocatalytic process was optimized with respect to the concentrations of the model substances during degradation. The decrease of the amine concentrations was found to be maximum at a pH of 10. The time-dependence of the formation of cationic breakdown products, such as NH3/NH4 and short-chain alkyl- and alkanolamines was studied by analyses with single column ion chromatography. The experimental data show that the photodegradation follows a Langmuir-Hinshelwood kinetic. The mineralization of the model substances also was monitored by measurements of the decrease of the TOC and of the formation of NO2 and NO3. The different mineralization efficiencies for the model substances studied are discussed with regard to their structure and adsorption behaviour on the photocatalyst. A possible breakdown mechanism involving the electrophilic attack of the hydroxyl radical is given. The applicability of the TiO2-assisted photocatalytic degradation of C2H5NH2 and (C2H5)2NH was tested at the pilot plant-scale with real solar radiation. The degradation rates and products obtained were similar to those found in the laboratory experiments.     

V/Ce共掺杂TiO2光催化降解甲醛的实验研究

采用溶胶-凝胶法制备了不掺杂、V掺杂、Ce掺杂、V/Ce共掺杂纳米TiO2光催化剂,并将其分别负载于瓷砖上,利用X射线衍射分析（XRD）和扫描电镜分析（SEM）技术对薄膜样品的结构和形貌进行了表征。通过对甲醛的降解实验评价光催化剂的光催化活性。实验结果表明,光催化剂的负载量、共掺杂离子的掺杂量、掺杂配比、煅烧温度影响纳米TiO2的光催化活性。V/Ce共掺杂TiO2光催化剂产生了协同效应,其光催化活性优于纯TiO2和单掺杂TiO2样品。     

改性TiO_2光催化降解三苯甲烷类污染物

以硫酸钛为原料采用水热法制备了掺Fe3＋TiO2晶体粉末,采用X射线衍射仪（XRD）对样品的结构进行了表征。在可见光条件下,用溴酚蓝、甲基绿、甲基蓝、孔雀石绿、甲基紫和碱性品红等6种典型三苯甲烷类化合物为目标降解物,研究了以自制的掺Fe3＋TiO2晶体粉末对它们的催化降解作用。实验结果表明,制备的掺Fe3＋TiO2晶体属于锐钛矿型。6种化合物的光催化降解反应遵循拟一级动力学规律,且可用Langmuir-Hinshelwood（L-H）动力学模型描述,其表观反应速度常数（k）的大小顺序为：溴酚蓝〈甲基绿〈甲基蓝〈孔雀石绿〈甲基紫〈碱性品红,大小变化次序与其半衰期t1/2成反比,并从分子结构上对它们的降解规律进行定性解释。     

Dye decomposition and air de-pollution performance of TiO2/SiO2 and N-TiO2/SiO2 photocatalysts coated on Portland cement mortar substates

Environmental Science and Pollution Research - In this study, the newly synthesized TiO2 and N doped TiO2 clusters were added to silica sol to synthesize N-TiO2/SiO2 composites via the...     

Simultaneous decontamination of hexavalent chromium and methyl tert-butyl ether by UV/TiO2 process

Hexavalent chromium and methyl tert-butyl ether (MTBE) are two important environmental pollutants. Simultaneous decontamination of Cr(VI) and MTBE was studied by UV/TiO2 process. The influences of pH and the concentrations of pollutants on the kinetics of the photocatalytic reactions were evaluated. Dark adsorption tests showed that the acidic pH favored the adsorption of Cr(VI) while neutral pH favored the adsorption of MTBE. Under UV irradiation, Cr(VI) reduction was observed in Cr(VI)/TiO2 system, and MTBE oxidation was observed in MTBE/TiO2 system. The system containing Cr(VI) and MTBE by UV/TiO2 process demonstrated the synergistic effect between oxidation of MTBE and reduction of Cr(VI). The results demonstrated that two pollutants Cr(VI) and MTBE could be eliminated simultaneously by UV/TiO2 process. tert-Butyl formate, tert-butyl alcohol and acetone were identified as primary degradation products of MTBE by gas chromatography-mass spectrometry in the degradation of MTBE by UV/TiO2 process.     

Photocatalytic degradation of imazethapyr herbicide at TiO2/H2O interface

The photocatalytic degradation of imazethapyr, a herbicide of the imidazolinone family, was investigated in an aqueous suspension of titanium dioxide used as a catalyst. A pseudo-first order kinetic model was employed to discuss the results. The effect of catalyst loading, initial concentration of imazethapyr, hydrogen peroxide, pH value, and temperature were investigated. Imazethapyr disappearance as a function of irradiation time was analyzed by HPLC. The ammonium ion formation was determined spectrophotometrically at 694 nm. The degradation was observed to proceed more favorably at natural pH (ca. 4.4) when the pH was varied in the range from 2 to 11. The addition of hydrogen peroxide to the TiO2 suspension enhanced the degradation rate constant up to 5.0x10(-3) mol l-1, but decreased it at higher concentrations. The degradation rate constants decreased by 19% with a temperature increase from 20 to 40 degrees C in the TiO2 suspension, whereas a 16% increase in imazethapyr direct photolysis was observed for the same temperature range. This behavior indicates the occurrence of physisorption between TiO2 and imazethapyr molecules.     

Photocatalytic oxidation of toxic organohalides with TiO2/UV: the effects of humic substances and organic mixtures

TiO2/UV photocatalytic oxidation of DDT (1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane), 1,2,3-trichlorobenzene and 4-chlorophenol were examined in aqueous solution in the presence of humic substances and organic mixtures to study if the degradation rates were affected. Both commercial and natural humic substances were observed to retard the photodegradation rates, with a greater effect from the natural humic substances. Acetonitrile and isopropanol also caused significant retardation of 4-chlorophenol photodegradation. The overall retardation can be attributed to the combination of light attenuation, inhibition and competition effects. Moreover, the TiO2/UV system favors the decomposition of compounds that have stronger adsorption onto the TiO2 surface. To engineer effective treatment facilities that use the TiO2/UV system for the treatment of toxic substances in wastewater, the methodology must allow for concerns about adventitious species which are present.     

CNTs/TiO2/CS光降解苯的动力学

综合光催化氧化苯的动力学过程、光辐射场模型和质量守恒定律,采用平板型反应器建立了碳纳米管/二氧化钛/壳聚糖（CNTs/TiO2/CS）催化薄膜光催化氧化气相苯的数学模型;该模型考虑了光强、相对湿度、初始浓度与气体流速对气相苯光降解的影响。结果表明,建立的数学模型与实验结果吻合较好。