Toxicity of leachate from bottom ash in a road construction

A test road constructed with municipal solid waste incineration (MSWI) bottom ash was monitored over a period of 36 months. Using chemical and toxicological characterisation, the environmental impact of leachates from bottom ash was evaluated and compared with leachates from gravel used as reference. Initial leaching of Cl, Cu, K, Na, NH4-N and TOC from bottom ash was of major concern. However, the quality of the bottom ash leachate approached that of the gravel leachate with time. Leachates from the two materials were compared regarding the concentration of pollutants using multivariate data analyses (MVDA). A standardized luminescent bacteria assay using Vibrio fischeri did not show any toxicity, most likely because saline contamination can mask the toxic response and stimulate luminescence in these marine bacteria. A mung bean assay using Phaseolus aureus revealed that the toxicity of bottom ash leachate collected at the very beginning of the experimental period (October 2001 and May 2002) might be attributed to the following components and their respective concentrations in mg l(-1): Al (34.2-39.2), Cl (2914-16,446), Cu (0.48-1.92), K (197-847), Na (766-4180), NH4-N (1.80-8.47), total-N (12.0-18.5), and TOC (34.0-99.0). The P. aureus assay was judged as a promising environmental tool in assessing the toxicity of bottom ash leachate.     

Assessment of mobility and bioavailability of contaminants in MSW incineration ash with aquatic and terrestrial bioassays

Incineration of municipal solid waste (MSW) is a waste treatment method which can be sustainable in terms of waste volume reduction as well as a source of renewable energy. In the process fly and bottom ash is generated as a waste material. The ash residue may vary greatly in composition depending on the type of waste incinerated and it can contain elevated levels of harmful contaminants such as heavy metals. In this study, the ecotoxicity of a weathered, untreated incineration bottom ash was characterized as defined by the H14 criterion of the EU Waste Framework Directive by means of an elemental analysis, leaching tests followed by a chemical analysis and a combination of aquatic and solid-phase bioassays. The experiments were conducted to assess the mobility and bioavailability of ash contaminants. A combination of aquatic and terrestrial bioassays was used to determine potentially adverse acute effects of exposure to the solid ash and aqueous ash leachates. The results from the study showed that the bottom ash from a municipal waste incineration plant in mid-Sweden contained levels of metals such as Cu, Pb and Zn, which exceeded the Swedish EPA limit values for inert wastes. The chemical analysis of the ash leachates showed high concentrations of particularly Cr. The leachate concentration of Cr exceeded the limit value for L/S 10 leaching for inert wastes. Filtration of leachates prior to analysis may have underestimated the leachability of complex-forming metals such as Cu and Pb. The germination test of solid ash and ash leachates using T. repens showed a higher inhibition of seedling emergence of seeds exposed to the solid ash than the seeds exposed to ash leachates. This indicated a relatively low mobility of toxicants from the solid ash into the leachates, although some metals exceeded the L/S 10 leaching limit values for inert wastes. The Microtox® toxicity test showed only a very low toxic response to the ash leachate exposure, while the D. magna immobility test showed a moderately high toxic effect of the ash leachates. Overall, the results from this study showed an ecotoxic effect of the solid MSW bottom ash and the corresponding ash leachates. The material may therefore pose an environmental risk if used in construction applications. However, as the testing of the solid ash was rather limited and the ash leachate showed an unusually high leaching of Cr, further assessments are required in order to conclusively characterize the bottom ash studied herein as hazardous according to the H14 criterion.     

Leachate formation and characteristics from gasification and grate incineration bottom ash under landfill conditions

Characteristics and formation of leachates from waste gasification and grate firing bottom ash were studied using continuous field measurements from 112 m³ lysimeters embedded into landfill body for three years. In addition, the total element concentrations of the fresh ash were analysed and laboratory batch tests were performed to study leachate composition. The three-year continuous flow measurement showed that about one fifth of the leachates were formed, when the flow rate was >200 l/d, covering <3.5% of the study time. After three years, the liquid/solid-ratio for the quenched grate ash was 1 (l/kg (d.m.)) and for the initially dry gasification ash 0.4 (l/kg (d.m.)). The low initial water and residual carbon content of the gasification ash kept the leachate pH at a high level (>13) major part of the study. In the grate ash leachate pH was lower (<8) due to the presence of organic carbon and biodegradation indicated by biological oxygen demand and redox potential measurements. In the gasification ash the high pH probably delayed leaching of major elements such as Ca, therefore, raising the need for a longer after-care period. The high pH also explains the higher leaching of As from the gasification ash compared to the grate ash both in the batch test and under landfill conditions.     

Leachability of Cr(VI) and other metals from asphalt composites with addition of filter dust

The potential use of filter dust in asphalt composites for road construction was investigated. Filter dust contains high concentrations of metals, of which Cr(VI) and Pb are leached with water. Compact and ground asphalt composites with addition of 2% of filter dust by mass were studied. In order to evaluate their environmental impact, leachability tests were performed using water and salt water as leaching agents. The concentrations of Cr(VI) and Pb were determined in leachates over a time period of 182 days. The results indicated that Pb was not leached with leaching agents from asphalt composites. Cr(VI) was also not leached with leaching agents from compact asphalt composites. However, in ground asphalt composites, Cr(VI) was leached with water in concentrations up to 220 microg L(-1) and in salt water up to 150 microg L(-1). From the physico-mechanical and environmental aspects, filter dust can be used as a component in asphalt mixtures.     

Life cycle based risk assessment of recycled materials in roadway construction

This paper uses a life-cycle assessment (LCA) framework to characterize comparative environmental impacts from the use of virgin aggregate and recycled materials in roadway construction. To evaluate site-specific human toxicity potential (HTP) in a more robust manner, metals release data from a demonstration site were combined with an unsaturated contaminant transport model to predict long-term impacts to groundwater. The LCA determined that there were reduced energy and water consumption, air emissions, Pb, Hg and hazardous waste generation and non-cancer HTP when bottom ash was used in lieu of virgin crushed rock. Conversely, using bottom ash instead of virgin crushed rock increased the cancer HTP risk due to potential leachate generation by the bottom ash. At this scale of analysis, the trade-offs are clearly between the cancer HTP (higher for bottom ash) and all of the other impacts listed above (lower for bottom ash). The site-specific analysis predicted that the contaminants (Cd, Cr, Se and Ag for this study) transported from the bottom ash to the groundwater resulted in very low unsaturated zone contaminant concentrations over a 200 year period due to retardation in the vadose zone. The level of contaminants predicted to reach the groundwater after 200 years was significantly less than groundwater maximum contaminant levels (MCL) set by the US Environmental Protection Agency for drinking water. Results of the site-specific contaminant release estimates vary depending on numerous site and material specific factors. However, the combination of the LCA and the site specific analysis can provide an appropriate context for decision making. Trade-offs are inherent in making decisions about recycled versus virgin material use, and regulatory frameworks should recognize and explicitly acknowledge these trade-offs in decision processes.     

Metal releases from a municipal solid waste incineration air pollution control residue mixed with compost

The influence of 10 wt.% mature compost was tested on the heavy metal leachate emissions from a calcium-rich municipal solid waste incineration air pollution control residue (MSWI APC). Apart from elongated columns (500 and 1250 mm), an otherwise norm compliant European percolation test setup was used. More than 99% of the metals Al, As, Cd, Cr, Cu, Fe and Ni were left in the APC residue after leaching to a liquid-to-solid ratio (L/S) of 10. Apparent short-term effects of elevated leachate DOC concentrations on heavy metal releases were not detected. Zn and Pb leachate concentrations were one order of magnitude lower for L/S 5 and 10 from the pure APC residue column, which suggests a possible long-term effect of compost on the release of these elements. Prolonging the contact time between the pore water and the material resulted in elevated leachate concentrations at L/S 0.1 to L/S 1 by a factor of 2. Only Cr and Pb concentrations were at their maxima in the first leachates at L/S 0.1. Equilibrium speciation modelling with the PHREEQC code suggested portlandite (Ca(OH)2) to control Ca solubility and pH.     

High temperature co-treatment of bottom ash and stabilized fly ashes from waste incineration

Bottom ashes from two Danish municipal solid waste incineration plants were heated at 900 degrees C with iron oxide stabilized air pollution control residues at actual mass flow ratios (9:1), simulating a treating method for the residues. The two residues were co-treated, producing one combined stream that may be utilized as a secondary road construction material. Scanning electron microscope analysis and grain size distribution analysis indicated that sintering of the particles did not occur. Batch leaching tests at liquid/solid 10 l/kg at a range of pH-values (6-10) quantified with respect to Cd, Cr and Pb revealed significant positive effects of co-heating the ashes, although Pb showed slightly increased leaching. At a liquid/solid ratio of 10 l/kg the leachate concentrations were still low at pH 7-10 and the release of Pb was, thus, not expected to limit the utilization of the mixed ashes. The process, thus, fixates the metals in the solid residues without altering the leaching properties of the bottom ash too significantly.     

Mechanically-biologically treated municipal solid waste as a support medium for microbial methane oxidation to mitigate landfill greenhouse emissions

The residual fraction of mechanically-biologically treated municipal solid waste (MBT residual) was studied in the laboratory to evaluate its suitability and environmental compatibility as a support medium in methane (CH(4)) oxidative biocovers for the mitigation of greenhouse gas emissions from landfills. Two MBT residuals with 5 and 12 months total (aerobic) biological stabilisation times were used in the study. MBT residual appeared to be a favourable medium for CH(4) oxidation as indicated by its area-based CH(4) oxidation rates (12.2-82.3 g CH(4) m(-2) d(-1) at 2-25 degrees C; determined in CH(4)-sparged columns). The CH(4) oxidation potential (determined in batch assays) of the MBT residuals increased during the 124 d column experiment, from <1.6 to a maximum of 104 microg CH(4) g(dw)(-1) h(-1) (dw=dry weight) at 5 degrees C and 578 microg CH(4) g(dw)(-1) h(-1) at 23 degrees C. Nitrous oxide (N(2)O) production in MBT residual (<15 microg N(2)O kg(dw)(-1) d(-1) in the CH(4) oxidative columns) was at the lower end of the range of N(2)O emissions reported for landfills and non-landfill soils, and insignificant as a greenhouse gas source. Also, anaerobic gas production (25.6 l kg(dw)(-1) during 217 d) in batch assays was low, indicating biological stability of the MBT residual. The electrical conductivities (140-250 mS m(-1)), as well as the concentrations of zinc (3.0 mg l(-1)), copper (0.5 mg l(-1)), arsenic (0.3 mg l(-1)), nickel (0.1 mg l(-1)) and lead (0.1 mg l(-1)) in MBT residual eluates from a leaching test (EN-12457-4) with a liquid/solid (L/S) ratio of 10:1, suggest a potential for leachate pollutant emissions which should be considered in plans to utilise MBT residual. In conclusion, the laboratory experiments suggest that MBT residual can be utilised as a support medium for CH(4) oxidation, even at low temperatures, to mitigate greenhouse gas emissions from landfills.     

Demobilisation of critical contaminants in four typical waste-to-energy ashes by carbonation

Two bottom ashes, one air pollution control (APC) residue and one fly ash from three different Swedish municipal solid waste incineration (MSWI) plants were characterised regarding the leaching of environmentally relevant components. Characterisation was performed using a diffusion tank leaching test. The impact of carbonation on the release of eight critical components, i.e., Cl(-), Cr, Cu, Mo, Pb, Sb, Se, SO(4)(2-) and Zn, was assessed at a lab-scale and showed carbonation to have a more pronounced demobilising effect on critical components in bottom ashes than in APC residue and fly ash. From grate type incinerator bottom ash, the release of Cr decreased by 97%, by 63% for Cu and by 45% for Sb. In the investigated APC residue, the releases of Cr, Se and Pb were defined as critical, although they either remained unaffected or increased after carbonation. Cl(-) and SO(4)(2-) remained mobile after carbonation in all investigated residues.     

Metal leaching from MSWI bottom ash as affected by salt or dissolved organic matter

In order to manage municipal solid waste incineration (MSWI) bottom ash safely, risk assessments, including the prediction of leaching under different field conditions, are necessary. In this study, the influence of salt or dissolved organic matter (DOM) in the influent on metal leaching from MSWI bottom ash was investigated in a column experiment. The presence of salt (0.1M NaCl) resulted in a small increase of As leaching, whereas no impact on leachate concentration was found when lakewater DOM (35.1mg/l dissolved organic carbon) was added. Most of the added DOM was retained within the material. Further, X-ray spectroscopy revealed that Cu(II) was the dominating form of Cu and that it probably occurred as a CuO-type mineral. The Cu(2+) activity in the MSWI bottom ash leachate was most likely determined by the dissolution of CuO together with the formation of Cu-DOM complexes and possibly also by adsorption to (hydr)oxide minerals. The addition of lake DOM in the influent resulted in lower saturation indices for CuO in the leachates, which may be due to slow CuO dissolution kinetics in combination with strong Cu-DOM complexation.     

Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

A study of Cr(VI) in ashes from fluidized bed combustion of municipal solid waste: leaching, secondary reactions and the applicability of some speciation methods

The use of the fluidized bed technique for the combustion of municipal solid waste is a rather new concept. This type of combustor produces ash residues with somewhat different properties than the residues generated from the traditional mass burn techniques. Therefore, chemical characterization and the investigation of toxic metals behavior during ash water reactions are necessary for the safe disposal of these residues. In the present work, the total elemental composition, mineralogy and leaching behavior of ashes from the combustion of municipal solid waste in a fluidized bed combustion boiler have been investigated. The cyclone ash and, in particular, the filter ash contained considerable amounts of soluble substances, thus giving leachates with high levels of Cl-, Na+, K+, Ca2 + and Al(IIl). On the other hand, the two ash fractions taken in the boiler, the bottom and hopper ashes, were much more stable with respect to the release of salts and heavy metals. Since Cr(VI) is mobile and toxic its release from combustion residues can pose environmental problem. Even though the total Cr contents were similar in all ashes studied, the bottom ash gave about a thousand times higher levels of Cr(VI) in test leachates than the hopper, cyclone and filter ashes. However, it was found that the leached amount of Cr(VI) from the bottom ash decreased significantly when bottom ash was mixed with the hopper ash. The most probable cause for this decrease is the coupled oxidation of Al(0) to Al(III) and reduction of dissolved Cr(VI) to Cr(III). This finding that the mixing of two ash streams from the same boiler could result in the immobilization of Cr may point at a simple stabilization method. Selective extraction of water soluble, exchangeable and sparingly soluble forms of Cr(VI) was also investigated. Extraction methods were evaluated for their suitability for ash matrixes. It was found that interferences due to the presence of reducing substances in some ash materials may occur.     

Leaching behavior of heavy metals from municipal solid waste incineration bottom ash and its geochemical modeling

With the increase in the number of municipal solid waste incineration (MSWI) plants constructed in China recently, great attention has been paid to the heavy metal leaching toxicity of MSWI residues. In this study, the effects of various parameters, including extractant, leaching time, liquid-to-solid ratio, leachate pH, and heavy metal content, on the release properties of Cd, Cr, Cu, Ni, Pb, and Zn from MSWI bottom ash were investigated. Partial least-squares analysis was employed to highlight the interrelationships between the factors and response variables. Both experimental research and geochemical modeling using Visual MINTEQ software were conducted to study the pH-dependent leaching behavior of these metals in fresh and weathered bottom ash, considering precipitation/dissolution and surface complexation reactions (adsorption by hydrous ferric oxide and amorphous aluminum oxide/hydroxide). The results showed that leachate pH was the predominant factor influencing heavy metal leachability. The leaching of Cu, Pb, and Zn was mainly controlled by precipitation/dissolution reactions, whereas surface complexation had some effect on the leaching of Cr, Cd, and Ni for certain pH ranges. The modeling results aggreed well with the experimental results. Part of this work was presented at the Fourth International Conference on Combustion, Incineration/Pyrolysis and Emission Control (i-CIPEC)     

Leaching behaviour of elements and evaluation of pre-treatment methods for municipal solid waste incinerator residues in column leaching tests.

Two new pre-treatment methods (water-washing/carbonation and carbonation/phosphate stabilization) of municipal solid waste (MSW) incinerator residues were evaluated by column leaching tests under aerobic conditions and anaerobic conditions (which were changed to aerobic conditions after 10 months). A mixture of bottom ash and fly ash (5:1 ratio) was pre-treated using each method. Shredded incombustible residues (SIR) were added to each ash preparation in proportions similar to the ratios present in landfills. For comparison, landfill wastes typical of Japan, namely, a mixture of bottom ash, chelating-pre-treated fly ash, and SIR, were also examined. Leachate samples were collected periodically and analysed over a 15-month period. When compared with chelating pretreatment, both water-washing/carbonation and carbonation/ phosphate stabilization reduced the leaching of Pb, Al, and Cu by about one to two orders of magnitude. Moreover, the initial concentrations of Ca and Pb in leachates from column of water-washing/carbonation were 56-57% and 84-96% less than those from the column of carbonation/phosphate stabilization. Therefore, water-washing/carbonation was considered to be a promising approach to obtain early waste stabilization and to reduce the release of heavy metals to near-negligible levels. The leaching behaviour of elements was also discussed.     

Charge-based fractionation of oxyanion-forming metals and metalloids leached from recycled concrete aggregates of different degrees of carbonation: A comparison of laboratory and field leaching tests

The release and charge-based fractionation of As, Cr, Mo, Sb, Se and V were evaluated in leachates generated from recycled concrete aggregates (RCA) in a laboratory and at a field site. The leachates, covering the pH range 8.4-12.6, were generated from non-carbonated, and artificially and naturally carbonated crushed concrete samples. Comparison between the release of the elements from the non-carbonated and carbonated samples indicated higher solubility of the elements from the latter. The laboratory leaching tests also revealed that the solubility of the elements is low at the “natural pH” of the non-carbonated materials and show enhancement when the pH is decreased. The charge-based fractionation of the elements was determined by ion-exchange solid phase extraction (SPE); it was found that all the target elements predominantly existed as anions in both the laboratory and field leachates. The high fraction of the anionic species of the elements in the leachates from the carbonated RCA materials verified the enhanced solubility of the oxyanionic species of the elements as a result of carbonation. The concentrations of the elements in the leachates and SPE effluents were determined by inductively coupled plasma mass spectrometry (ICP-MS).     

A comparison of small-scale,pilot-scale and large-scale tests for predicting leaching behaviour of landfilled wastes

Landfills generate emissions over long periods, often longer than a lifetime. The longest lasting emission is leachate. In order to estimate the future requirements for leachate treatment, different kinds of leaching tests may be applied. In this paper, shaking leaching tests (SLT), landfill-simulator leaching tests and a field-cell leaching test performed with ash, municipal solid waste (MSW) and MSW+ash are evaluated. The tests are compared and the factors influencing leaching are identified and discussed. The factors are: liquid to solid (L/S) ratio, water withdrawal, recirculation rate, presence or absence of biological processes, size of particles, duration of experiment, temperature and pre-treatment of the waste. The presence of biological processes has the greatest impact on leaching and is the main reason why SLT is less useful for long-term predictions. The landfill simulator tests were found to be useful for several different kinds of predictions. However, they are not reliable for predicting the L/S required for reaching a certain concentration. The possibilities for reliable long-term predictions would be facilitated by a better knowledge of the influence of various factors on leaching. Such an increased knowledge would make it possible to enhance waste stabilisation in leaching tests as well as in full-scale landfills.     

Life cycle assessment of disposal of residues from municipal solid waste incineration: recycling of bottom ash in road construction or landfilling in Denmark evaluated in the ROAD-RES model

Two disposal methods for MSWI bottom ash were assessed in a new life cycle assessment (LCA) model for road construction and disposal of residues. The two scenarios evaluated in the model were: (i) landfilling of bottom ash in a coastal landfill in Denmark and (ii) recycling of bottom ash as subbase layer in an asphalted secondary road. The LCA included resource and energy consumption, and emissions associated with upgrading of bottom ash, transport, landfilling processes, incorporation of bottom ash in road, substitution of natural gravel as road construction material and leaching of heavy metals and salts from bottom ash in road as well as in landfill. Environmental impacts associated with emissions to air, fresh surface water, marine surface water, groundwater and soil were aggregated into 12 environmental impact categories: Global Warming, Photochemical Ozone Formation, Nutrient Enrichment, Acidification, Stratospheric Ozone Depletion, Human Toxicity via air/water/soil, Ecotoxicity in water/soil, and a new impact category, Stored Ecotoxicity to water/soil that accounts for the presence of heavy metals and very persistent organic compounds that in the long-term might leach. Leaching of heavy metals and salts from bottom ash was estimated from a series of laboratory leaching tests. For both scenarios, Ecotoxicity(water) was, when evaluated for the first 100 yr, the most important among the twelve impact categories involved in the assessment. Human Toxicity(soil) was also important, especially for the Road scenario. When the long-term leaching of heavy metals from bottom ash was evaluated, based on the total content of heavy metals in bottom ash, all impact categories became negligible compared to the potential Stored Ecotoxicity, which was two orders of magnitudes greater than Ecotoxicity(water). Copper was the constituent that gave the strongest contributions to the ecotoxicities. The most important resources consumed were clay as liner in landfill and the groundwater resource which was potentially spoiled due to leaching of salts from bottom ash in road. The difference in environmental impacts between landfilling and utilization of bottom ash in road was marginal when these alternatives were assessed in a life cycle perspective.     

Leaching assessment of road materials containing primary lead and zinc slags

Characterisation of the leaching behaviour of waste-containing materials is a crucial step in the environmental assessment for reuse scenarios. In our research we applied the multi-step European methodology ENV 12-920 to the leaching assessment of road materials containing metallurgical slag. A Zn slag from an imperial smelting furnace (ISF) and a Pb slag from a lead blast furnace (LBF) are investigated. The two slags contain up to 11.2 wt% of lead and 3.5 wt% of zinc and were introduced as a partial substitute for sand in two road materials, namely sand-cement and sand-bitumen. At the laboratory scale, a leaching assessment was performed first through batch equilibrium leaching tests. Second, the release rate of the contaminants was evaluated using saturated leaching tests on monolithic material. Third, laboratory tests were conducted on monolithic samples under intermittent wetting conditions. Pilot-scale tests were conducted for field testing of intermittent wetting conditions. The results show that the release of Pb and Zn from the materials in a saturated scenario was controlled by the pH of the leachates. For the intermittent wetting conditions, an additional factor, blocking of the pores by precipitation during the drying phase is proposed. Pilot-scale leaching behaviour only partially matched with the laboratory-scale test results: new mass transfer mechanisms and adapted laboratory leaching tests are discussed.     

Effect of sintering temperature on the properties and leaching of incinerator bottom ash.

The fine particle size fraction of municipal solid waste incinerator bottom ash is often problematic because reuse applications for this material are limited. In these experiments incinerator bottom ash with a particle size of less than 8 mm was processed using conventional ceramic production techniques involving wet milling, drying, compacting and sintering. The effect of sintering temperature on the sintered density, microstructure, acid neutralization capacity (ANC) and the release of metal ions as a function of leachate pH are reported. Sintering at 1080 degrees C produced samples with maximum density. This material contained diopside (CaMgSi2O6), clinoenstatite (Mg2Si2O6) and wollastonite (CaSiO3) as the major crystalline phases. The acid neutralization capacity of sintered samples is significantly lower than milled bottom ash, and further reduces as the sintering temperature increases. This is associated with reduced leaching of Ca from sintered ash samples under all leachate pH conditions. Heavy metals present in the incinerator bottom ash included Cr, Cu, Ni, Zn, Cd and Pb. Sintering under optimum conditions reduced the leachable fraction of these metals under aggressive acid conditions (leachate pH 3) by factors ranging from 90% for Ni to greater than 99% for Cr, Cd, Zn and Pb.     

Optimum Dose Of Lime And Fly Ash For Treatment Of Hexavalent Chromium–Contaminated Soil

The presence of hexavalent chromium, Cr(VI), in soil is an environmental concern due to its effect on human health. The concern arises from the leaching and the seepage of Cr(VI) from soil to groundwater. In this paper, a stabilization technology to prevent this problem was simulated on an artificial soil contaminated with hexavalent chromium. The process is a physico-chemical treatment in which the toxic pollutant is physically entrapped within a solid matrix formed by the pozzolanic reactions of lime and fly ash to reduce its leachability and, therefore, its toxicity. This paper presents the optimum ratio of fly ash and lime in order to stabilize artificial soils contaminated with 0.4 wt.% of Cr (VI) in a brief term process. The degree of chromium released from the soil was evaluated using a modified Toxicity Characteristic Leaching Procedure (TCLP) by US Environmental Protection Agency (EPA). Overall, experimental results showed reduced leachability of total and hexavalent chromium from soils treated with both fly ash and quicklime, and that leachability reduction was more effective with increasing amount of fly ash and quicklime. Stabilization percentages between 97.3% and 99.7% of the initial chromium content were achieved, with Cr(VI) concentration in the TCLP leachates below the US EPA limit for chromium of 5 mg/l. Adequate treatment was obtained after 1 day of curing with just 25% fly ash and 10% quicklime.