Using multivariate regression modeling for sampling and predicting chemical characteristics of mixed waste in old landfills

Municipal solid waste landfills pose a threat on environment and human health, especially old landfills which lack facilities for collection and treatment of landfill gas and leachate. Consequently, missing information about emission flows prevent site-specific environmental risk assessments. To overcome this gap, the combination of waste sampling and analysis with statistical modeling is one option for estimating present and future emission potentials. Optimizing the tradeoff between investigation costs and reliable results requires knowledge about both: the number of samples to be taken and variables to be analyzed.This article aims to identify the optimized number of waste samples and variables in order to predict a larger set of variables. Therefore, we introduce a multivariate linear regression model and tested the applicability by usage of two case studies. Landfill A was used to set up and calibrate the model based on 50 waste samples and twelve variables. The calibrated model was applied to Landfill B including 36 waste samples and twelve variables with four predictor variables.The case study results are twofold: first, the reliable and accurate prediction of the twelve variables can be achieved with the knowledge of four predictor variables (Loi, EC, pH and Cl). For the second Landfill B, only ten full measurements would be needed for a reliable prediction of most response variables. The four predictor variables would exhibit comparably low analytical costs in comparison to the full set of measurements. This cost reduction could be used to increase the number of samples yielding an improved understanding of the spatial waste heterogeneity in landfills.Concluding, the future application of the developed model potentially improves the reliability of predicted emission potentials. The model could become a standard screening tool for old landfills if its applicability and reliability would be tested in additional case studies.     

Long-term behavior of municipal solid waste landfills

A method is presented to predict the long-term behavior of element concentrations (non-metals and metals) in the leachate of a municipal solid waste (MSW) landfill. It is based on water flux and concentration measurements in leachates over one year, analysis of drilled cores from MSW landfills and leaching experiments with these samples. A mathematical model is developed to predict the further evolution of annual flux-weighted mean element concentrations in leachates after the “intensive reactor phase”, i.e. after the gas production has dropped to a very low level. The results show that the organic components are the most important substances to control until the leachate is compatible with the environment. This state of low emissions, the so-called “final storage quality”, will take many centuries to be achieved in a moderate climate.     

Analysis of emergency situations at municipal solid waste landfills

Journal of Material Cycles and Waste Management - This work focuses on the issue of emergency prevention in the operation of municipal solid waste landfills. In this work, an emergency is...     

Modelling the biochemical degradation of solid waste in landfills

This paper describes the concept of a generic spatially distributed numerical model that has been developed to contain and link sub-models of landfill processes in order to simulate solid waste degradation and gas generation in landfills. The model includes the simulation of the transport of leachate and gases, and the consolidation of the solid waste. The structure of the model consists of linked discrete constant volume elements. The paper outlines the theoretical background that provides the framework to contain the numerical procedures that make up the model. Details are also given of the approach to the modelling of the chemistry and microbiology of solid waste degradation.     

Mechanical behavior of inert waste landfills under seismic condition

Journal of Material Cycles and Waste Management - Mechanical properties and slope stability of inert waste landfills under seismic condition were studied with three different approaches: in-situ...     

Two-year performance by evapotranspiration covers for municipal solid waste landfills in northwest Ohio

Evapotranspiration (ET) covers have gained interest as an alternative to conventional covers for the closure of municipal solid waste (MSW) landfills because they are less costly to construct and are expected to have a longer service life. Whereas ET covers have gained acceptance in arid and semi-arid regions (defined by a precipitation (P) to potential evapotranspiration (PET) ratio less than 0.75) by meeting performance standards (e.g. rate of percolation), it remains unclear whether they are suitable for humid regions (P:PET greater than 0.75). The goal of this project is to extend their application to northwest Ohio (P:PET equals 1.29) by designing covers that produce a rate of percolation less than 32 cm yr^?1, the maximum acceptable rate by the Ohio Environmental Protection Agency (OEPA). Test ET covers were constructed in drainage lysimeters (1.52 m diameter, 1.52 m depth) using dredged sediment amended with organic material and consisted of immature (I, plants seeded onto soil) or mature (M, plants transferred from a restored tall-grass prairie) plant mixtures. The water balance for the ET covers was monitored from June 2009 to June 2011, which included measured precipitation and percolation, and estimated soil water storage and evapotranspiration. Precipitation was applied at a rate of 94 cm yr^?1 in the first year and at rate of 69 cm yr^?1 in the second year. During the first year, covers with the M plant mixture produced noticeably less percolation (4 cm) than covers with the I plant mixture (17 cm). However, during the second year, covers with the M plant mixture produced considerably more percolation (10 cm) than covers with the I plant mixture (3 cm). This is likely due to a decrease in the aboveground biomass for the M plant mixture from year 1 (1008 g m^?2) to year 2 (794 g m^?2) and an increase for the I plant mixture from year 1 (644 g m^?2) to year 2 (1314 g m^?2). Over the 2-year period, the mean annual rates of percolation for the covers with the M and I plant mixtures were 7 and 8 cm yr^?1, which are below the OEPA standard. The results suggest the application of ET covers be extended to northwest Ohio and other humid regions.     

Overview of waste disposal and landfills/dumps in Asian countries

Many cities in developing Asian countries face serious problems in managing solid wastes. The annual waste generation increases in proportion to the rises in population and urbanization. Asian countries with greater rural populations produce more organic waste, such as kitchen wastes, and fewer recyclable items, such as paper, metals, and plastics. Reliable data on solid waste compositions are difficult to obtain, and even if available, they are often not updated. We report the most recent waste composition data in some developing Asian countries. We suggest that a better classification system for landfills is needed to address inconsistencies in data for sanitary landfill sites versus waste dumps. We also discuss the information on waste disposal trends and problems associated with general solid waste management in developing Asian countries.     

Distribution and attenuation of hazardous substances in uncontrolled solid waste landfills

The distribution, concentrations in various phases, attenuation and emissions of hazardous substances in Finnish municipal and industrial mixed-waste landfills were investigated in a 5 year field study. Pronounced irregular spatial variation in substance concentrations was observed within, and especially between, the sites. Most frequency distributions of contaminant concentrations in the fills were skewed toward small values. Related norms or reference values were occasionally exceeded. The attenuation of contaminants in the various phases within and around landfills varied according to the substance and site, reflecting retention and removal mechanisms. Lead and zinc were the most easily leached heavy metals in old landfills. The concentration distributions of toxicants in waterborne emissions were dominated by small values, but the maxima exceeded drinking water norms by up to 400 times. In municipal landfill gas, some halomethane concentrations (100 mg Nm⁻³) exceeded air quality norms. The estimates of contaminant fluxes were minor compared with, for example, industrial emissions. The overall toxic impacts of Finnish landfills thus seem relatively small, but may be important locally and require further study and caution. Associated issues in disposal risk assessment and management are briefly discussed.     

Modeling of perched leachate zone formation in municipal solid waste landfills

The paper presents a 1D mathematical model for the simulation of the percolation fluxes throughout a landfill for municipal solid waste (MSW). Specifically, the model was based on mass balance equations, that enable simulation of the formation of perched leachate zones in a landfill for MSW. The model considers the landfill divided in several layers evaluating the inflow to and outflow from each layer as well as the continuous moisture distribution. The infiltration flow was evaluated by means of the Darcy’s law for an unsaturated porous medium, while the moisture distribution evaluation has been carried out on the basis of the theory of the vertically distributed unsaturated flow. The solution of the model has been obtained by means of the finite difference method. The model has been applied to a semi-idealized landfill located in Palermo landfill (Bellolampo). Specifically, field measurements were conducted to determine the relationship between waste density and applied vertical strain. This relationship was then used to relate vertical strain to waste porosity. The inflow rate to the system was simulated via a synthetic hyetograph whose characteristics have been identified in a previous hydrologic study.Three simulations, each with a different initial moisture content, were conducted. The model results showed a different response of the landfill in terms both of flow rates throughout the landfill and moisture profile. Indeed, the initial moisture content drastically influenced not only the formation of perched leachate zones but also their extension. The model can be a useful tool in predicting potential for the formation of perched leachate zones.     

A performance-based system for the long-term management of municipal waste landfills

Landfills have been the dominant alternative for disposal of solid waste and there are tens of thousands of closed landfills throughout the world that require a long-term management strategy. In contrast to approaches based on time or target values, this paper describes a performance-based methodology for evaluation of post-closure care (PCC). Using the methodology, critical components of PCC at a landfill, including leachate and gas management, groundwater monitoring and cover integrity, are considered to determine whether a landfill meets defined conditions for functional stability and can transition from regulated PCC to a post-regulatory custodial care program representing de minimus care activities only. The methodology is predicated on understanding the biological, chemical, and physical behavior of a landfill and the presence of sufficient data to verify expected trends in landfill behavior. If an evaluation suggests that a change can be made to PCC, the landfill owner must perform confirmation monitoring and then surveillance monitoring at a decreasing frequency to verify that the change is protective of human health and the environment. A hypothetical case study showed that using the methodology to evaluate site-specific PCC requirements could result in increased environmental protection at comparable cost by spending available funds where they are most needed.     

Characterization of municipal solid waste from the main landfills of Havana city

The city of Havana, the political, administrative and cultural centre of Cuba, is also the centre of many of the economic activities of the nation: industries, services, scientific research and tourism. All of these activities contribute to the generation of municipal solid waste (MSW), which also impact other Cuban cities. Inadequate handling of waste and the lack of appropriate and efficient solutions for its final disposal and treatment increase the risk and possibility of contamination. The main difficulty in the development of a system of management of MSW lies in the lack of knowledge of the chemical composition of the waste that is generated in the country as a whole, and especially in Havana, where solid waste management decisions are made. The present study characterizes MSW in Havana city during 2004. The Calle 100, Guanabacoa and Ocho Vías landfills were selected for physical-chemical characterization of MSW, as they are the three biggest landfills in the city. A total of 16 indicators were measured, and weather conditions were recorded. As a result, the necessary information regarding the physical-chemical composition of the MSW became available for the first time in Cuba. The information is essential for making decisions regarding the management of waste and constitutes a valuable contribution to the Study on Integrated Management Plan of MSW in Havana.     

Comparison of slope stability in two Brazilian municipal landfills

The implementation of landfill gas to energy (LFGTE) projects has greatly assisted in reducing the greenhouse gases and air pollutants, leading to an improved local air quality and reduced health risks. The majority of cities in developing countries still dispose of their municipal waste in uncontrolled 'open dumps.' Municipal solid waste landfill construction practices and operating procedures in these countries pose a challenge to implementation of LFGTE projects because of concern about damage to the gas collection infrastructure (horizontal headers and vertical wells) caused by minor, relatively shallow slumps and slides within the waste mass. While major slope failures can and have occurred, such failures in most cases have been shown to involve contributory factors or triggers such as high pore pressures, weak foundation soil or failure along weak geosynthetic interfaces. Many researchers who have studied waste mechanics propose that the shear strength of municipal waste is sufficient such that major deep-seated catastrophic failures under most circumstances require such contributory factors. Obviously, evaluation of such potential major failures requires expert analysis by geotechnical specialists with detailed site-specific information regarding foundation soils, interface shearing resistances and pore pressures both within the waste and in clayey barrier layers or foundation soils. The objective of this paper is to evaluate the potential use of very simple stability analyses which can be used to study the potential for slumps and slides within the waste mass and which may represent a significant constraint on construction and development of the landfill, on reclamation and closure and on the feasibility of a LFGTE project. The stability analyses rely on site-specific but simple estimates of the unit weight of waste and the pore pressure conditions and use "generic" published shear strength envelopes for municipal waste. Application of the slope stability analysis method is presented in a case study of two Brazilian landfill sites; the Cruz das Almas Landfill in Maceio and the Muribeca Landfill in Recife. The Muribeca site has never recorded a slope failure and is much larger and better-maintained when compared to the Maceio site at which numerous minor slumps and slides have been observed. Conventional limit-equilibrium analysis was used to calculate factors of safety for stability of the landfill side slopes. Results indicate that the Muribeca site is more stable with computed factors of safety values in the range 1.6-2.4 compared with computed values ranging from 0.9 to 1.4 for the Maceio site at which slope failures have been known to occur. The results suggest that this approach may be useful as a screening-level tool when considering the feasibility of implementing LFGTE projects.     

Influence of mechanical-biological waste pre-treatment methods on the gas formation in landfills

In order to minimise emissions and environmental impacts, only pre-treated waste should be disposed of. For the last six years, a series of continuous experiments has been conducted at the Institute WAR, TU Darmstadt, in order to determine the emissions from pre-treated waste. Different kinds of pre-treated waste were incubated in several reactors and various data, including production and composition of the gas and the leachate, were collected. In this paper, the interim results of gas production and the gas composition from different types of waste after a running time of six years are presented and discussed.     

Oxygen intrusion into waste in old landfills of low organic content.

Oxygen invasion into old landfills was studied by assuming the installation of gas venting pipes to promote stabilization of waste. In an experiment using a column pack with old incombustible waste, oxygen intrusion was observed and the oxygen consumption rate was estimated. Oxygen diffused into the waste layer very quickly in the initial stage of the experiment, but oxygen concentration increased only gradually due to reduced gradient and decreasing oxygen consumption. The maximum oxygen consumption rate in packed waste was one-third of that in loosely deposited waste in a beaker measured in a respiration test. A mathematical model was created which fitted the experimental data well and a three-dimensional simulation of a full-scale landfill and a sensitivity analysis were performed.     

A review of approaches for the long-term management of municipal solid waste landfills

After closure, municipal solid waste (MSW) landfills must be managed and controlled to avoid adverse effects on human health and the environment (HHE). Aftercare (or post-closure care) can be brought to an end when the authorities consider the landfill to no longer pose a threat to HHE. Different approaches have been suggested for long-term landfill management and evaluation of aftercare completion. In this paper, research on aftercare and its completion is analyzed and regulatory approaches for the completion of landfill aftercare are reviewed. Approaches to aftercare could be categorized as (i) target values, (ii) impact/risk assessment, and (iii) performance based. Comparison of these approaches illustrates that each has limitations and strengths. While target values are typically used as screening indicators to be complemented with site-specific assessments, impact/risk assessment approaches address the core issue about aftercare completion, but face large uncertainties and require a high level of expertise. A performance-based approach allows for the combination of target values and impact/risk assessments in a consistent evaluation framework with the aim of sequentially reducing aftercare intensity and, ultimately, leading to the completion of aftercare. At a regulatory level, simple qualitative criteria are typically used as the primary basis for defining completion of aftercare, most likely due to the complexity of developing rigorous evaluation methodologies. This paper argues that development of transparent and consistent regulatory procedures represents the basis for defining the desired state of a landfill at the end of aftercare and for reducing uncertainty about the intensity and duration of aftercare. In this context, recently presented technical guidelines and the ongoing debate with respect to their regulatory acceptance are a valuable step towards developing strategies for the cost-effective protection of HHE at closed MSW landfills. To assess the practicality of evaluation methodologies for aftercare, well-documented case studies including regulatory review and acceptance are needed.     

Utilization of sepiolite materials as a bottom liner material in solid waste landfills

Landfill bottom liners are generally constructed with natural clay soils due to their high strength and low hydraulic conductivity characteristics. However, in recent years it is increasingly difficult to find locally available clay soils that satisfy the required engineering properties. Fine grained soils such as sepiolite and zeolite may be used as alternative materials in the constructions of landfill bottom liners. A study was conducted to investigate the feasibility of using natural clay rich in kaolinite, sepiolite, zeolite, and their mixtures as a bottom liner material. Unconfined compression tests, swell tests, hydraulic conductivity tests, batch and column adsorption tests were performed on each type of soil and sepiolite–zeolite mixtures. The results of the current study indicate that sepiolite is the dominant material that affects both the geomechanical and geoenvironmental properties of these alternative liners. An increase in sepiolite content in the sepiolite–zeolite mixtures increased the strength, swelling potential and metal adsorption capacities of the soil mixtures. Moreover, hydraulic conductivity of the mixtures decreased significantly with the addition of sepiolite. The utilization of sepiolite–zeolite materials as a bottom liner material allowed for thinner liners with some reduction in construction costs compared to use of a kaolinite-rich clay.     

Evaluating the biochemical methane potential (BMP) of low-organic waste at Danish landfills

The biochemical methane potential (BMP) is an essential parameter when using first order decay (FOD) landfill gas (LFG) generation models to estimate methane (CH₄) generation from landfills. Different categories of waste (mixed, shredder and sludge waste) with a low-organic content and temporarily stored combustible waste were sampled from four Danish landfills. The waste was characterized in terms of physical characteristics (TS, VS, TC and TOC) and the BMP was analyzed in batch tests. The experiment was set up in triplicate, including blank and control tests. Waste samples were incubated at 55 °C for more than 60 days, with continuous monitoring of the cumulative CH₄ generation. Results showed that samples of mixed waste and shredder waste had similar BMP results, which was in the range of 5.4–9.1 kg CH₄/ton waste (wet weight) on average. As a calculated consequence, their degradable organic carbon content (DOCC) was in the range of 0.44–0.70% of total weight (wet waste). Numeric values of both parameters were much lower than values of traditional municipal solid waste (MSW), as well as default numeric values in current FOD models. The sludge waste and temporarily stored combustible waste showed BMP values of 51.8–69.6 and 106.6–117.3 kg CH₄/ton waste on average, respectively, and DOCC values of 3.84–5.12% and 7.96–8.74% of total weight. The same category of waste from different Danish landfills did not show significant variation. This research studied the BMP of Danish low-organic waste for the first time, which is important and valuable for using current FOD LFG generation models to estimate realistic CH₄ emissions from modern landfills receiving low-organic waste.     

Evaluation of the geotechnical properties of MSW in two Brazilian landfills

The characteristics of municipal solid waste (MSW) play a key role in many aspects of waste disposal facilities and landfills. Because most of a landfill is made up of MSW, the overall stability of the landfill slopes are governed by the strength parameters and physical properties of the MSW. These parameters are also important in interactions involving the waste body and the landfill structures: cover liner, leachate and gas collection systems. On the other hand, the composition of the waste, which affects the geotechnical behavior of the MSW, is dependent on a variety of factors such as climate, disposal technology, the culture and habits of the local community. It is therefore essential that the design and stability evaluations of landfills in each region be performed based on the local conditions and the geotechnical characteristic of the MSW. The Bandeirantes Landfill, BL, in São Paulo and the Metropolitan Center Landfill, MCL, in Salvador, are among the biggest landfills in Brazil. These two disposal facilities have been used for the development of research involving waste mechanics in recent years. Considerable work has been made in the laboratory and in the field to evaluate parameters such as water and organic contents, composition, permeability, and shear strength. This paper shows and analyzes the results of tests performed on these two landfills. The authors believe that these results could be a good reference for certain aspects and geotechnical properties of MSW materials in countries with similar conditions.     

Phytoremediation and rehabilitation of municipal solid waste landfills and dumpsites: A brief review

Environmental problems posed by municipal solid waste (MSW) are well documented. Scientifically designed landfills and/or open dumpsites are used to dispose MSW in many developed and developing countries. Non-availability of land and need to reuse the dumpsite space, especially in urban areas, call for rehabilitation of these facilities. A variety of options have been tried to achieve the goals of rehabilitation. In the last couple of decades, phytoremediation, collectively referring to all plant-based technologies using green plants to remediate and rehabilitate municipal solid waste landfills and dumpsites, has emerged as a potential candidate. Research and development activities relating to different aspects of phytoremediation are keeping the interest of scientists and engineers alive and enriching the literature. Being a subject of multi-disciplinary interest, findings of phytoremediation research has resulted in generation of enormous data and their publication in a variety of journals and books. Collating data from such diverse sources would help understand the dynamics and dimensions of landfill and dumpsite rehabilitation. This review is an attempt in this direction.     

Estimation and field measurement of methane emission from waste landfills in Hanoi, Vietnam

A methodology for estimating the methane emissions from waste landfills in Hanoi, Vietnam, as part of a case study on Asian cities, was derived based on a survey of documents and statistics related to waste management, interviews with persons in charge, and field investigations at landfill sites. The waste management system in Hanoi was analyzed to evaluate the methane emissions from waste landfill sites. The quantity of waste deposited into the landfill was evaluated from an investigation of the waste stream. The composition of municipal waste was surveyed in several districts in the Hanoi city area, and the quantities of degradable organic waste that had been deposited into landfill for the past 15 years were estimated. Field surveys on methane emissions from landfills of different ages (0.5, 2, and 8 years) were conducted and their methane emissions were estimated to be 120, 22.5, and 4.38 ml/min/m², respectively. The first-order reaction rate of methane generation was obtained as 0.51/year. Methane emissions from waste landfills were calculated by a first-order decay model using this emission factor and the amount of landfilled degradable waste. The estimates of methane emissions using the model accorded well with the estimates of the field survey. These results revealed that methane emissions from waste landfills estimated by regional-specific and precise information on the waste stream are essential for accurately determining the behavior of methane emissions from waste landfills in the past, present, and future.