GROUND-WATER TEMPERATURE FLUCTUATIONS AT LYONS FERRY FISH HATCHERY,WASHINGTON1

ABSTRACT: The well field serving the Lyons Ferry Fish Hatchery has experienced reduced water temperatures following continued, periodic withdrawal of large volumes of water. In January 1985, the well field temperature was 49°F, which is less than the optimal 52°F for raising salmon and steelhead trout. The aquifer supplying the hatchery is in hydraulic and thermal connection with the Snake River and a flooded embayment of the Palouse River. Ground-water temperatures in the well field cycle on an annual basis in response to changes in surface water temperature and pumping rate. Numerical simulation of the well field, using a simplified mixing cell model, demonstrates the coupling of well field hydraulics and aquifer thermal response. Alternative pumping schedules indicate that it is feasible to adjust ground-water pumping to effectively store heat in the aquifer during the summer months when surface water temperatures are elevated. Sensitivity analysis of this model indicated that the primary controls of the system's thermal response are the volume of the aquifer assumed to contribute to the well field and temperature of the overlying surface water body.     

PREDICTING THE SUMMER TEMPERATURE OF SMALL STREAMS IN SOUTHWESTERN WISCONSIN1

ABSTRACT: One of the biggest challenges in managing cold water streams in the Midwest is understanding how stream temperature is controlled by the complex interactions among meteorologic processes, channel geometry, and ground water inflow. Inflow of cold ground water, shade provided by riparian vegetation, and channel width are the most important factors controlling summer stream temperatures. A simple screening model was used to quantitatively evaluate the importance of these factors and guide management decisions. The model uses an analytical solution to the heat transport equation to predict steady‐state temperature throughout a stream reach. The model matches field data from four streams in southwestern Wisconsin quite well (typically within 1°C) and helps explain the observed warming and cooling trends along each stream reach. The distribution of ground water inflow throughout a stream reach has an important influence on stream temperature, and springs are especially effective at providing thermal refuge for fish. Although simple, this model provides insight into the importance of ground water and the impact different management strategies, such as planting trees to increase shade, may have on summer stream temperature.     

LAKE HURON SURFACE WATER TEMPERATURE MAY – NOVEMBER, 19661

ABSTRACT. Data from seven vessel cruises from late May to early November permitted definition of the surface water temperature regime of Lake Huron on a monthly basis. Quantitative values are furnished for a portion of the warming, stable, and cooling periods. The lowest temperatures occurred near the center of the lake, southwest of Manitoulin Island, and at De Tour Passage. The highest temperatures occurred at the mouth of Saginaw Bay and in the southernmost portions of the lake. Comparison of the surface water temperatures with temperatures in the 21 - 30 m layer shows the heat storage lag characteristic of large lakes.     

Quantitative Assessment of Agricultural Runoff and Soil Erosion Using Mathematical Modeling: Applications in the Mediterranean Region

Three mathematical models, the runoff curve number equation, the universal soil loss equation, and the mass response functions, were evaluated for predicting nonpoint source nutrient loading from agricultural watersheds of the Mediterranean region. These methodologies were applied to a catchment, the gulf of Gera Basin, that is a typical terrestrial ecosystem of the islands of the Aegean archipelago. The calibration of the model parameters was based on data from experimental plots from which edge-of-field losses of sediment, water runoff, and nutrients were measured. Special emphasis was given to the transport of dissolved and solid-phase nutrients from their sources in the farmers' fields to the outlet of the watershed in order to estimate respective attenuation rates. It was found that nonpoint nutrient loading due to surface losses was high during winter, the contribution being between 50% and 80% of the total annual nutrient losses from the terrestrial ecosystem. The good fit between simulated and experimental data supports the view that these modeling procedures should be considered as reliable and effective methodological tools in Mediterranean areas for evaluating potential control measures, such as management practices for soil and water conservation and changes in land uses, aimed at diminishing soil loss and nutrient delivery to surface waters. Furthermore, the modifications of the general mathematical formulations and the experimental values of the model parameters provided by the study can be used in further application of these methodologies in watersheds with similar characteristics.     

Air‐Water Temperature Relationships in the Trout Streams of Southeastern Minnesota's Carbonate‐Sandstone Landscape

Carbonate‐sandstone geology in southeastern Minnesota creates a heterogeneous landscape of springs, seeps, and sinkholes that supply groundwater into streams. Air temperatures are effective predictors of water temperature in surface‐water dominated streams. However, no published work investigates the relationship between air and water temperatures in groundwater‐fed streams (GWFS) across watersheds. We used simple linear regressions to examine weekly air‐water temperature relationships for 40 GWFS in southeastern Minnesota. A 40‐stream, composite linear regression model has a slope of 0.38, an intercept of 6.63, and R² of 0.83. The regression models for GWFS have lower slopes and higher intercepts in comparison to surface‐water dominated streams. Regression models for streams with high R² values offer promise for use as predictive tools for future climate conditions. Climate change is expected to alter the thermal regime of groundwater‐fed systems, but will do so at a slower rate than surface‐water dominated systems. A regression model of intercept vs. slope can be used to identify streams for which water temperatures are more meteorologically than groundwater controlled, and thus more vulnerable to climate change. Such relationships can be used to guide restoration vs. management strategies to protect trout streams.     

Modeling the Effect of Summertime Heating on Urban Runoff Temperature1

Abstract: The summertime heating of runoff in urban areas is recognized as a common and consistent urban climatological phenomenon. In this study, a simple thermal urban runoff model (TURM) is presented for the net energy flux at the impervious surfaces of urban areas to account for the heat transferred to runoff. The first step in developing TURM consists of calculating the various factors that control how urban impervious areas absorb heat and transfer it to moving water on the surface. The runoff temperature is determined based on the interactions of the physical characteristics of the impervious areas, the weather, and the heat transfer between the moving film of runoff and the impervious surface common in urban areas. Key surface and weather factors that affect runoff temperature predictions are type of impervious surface, air temperature, humidity, solar radiation before and during rain, rainfall intensity, and rainfall temperature. Runoff from pervious areas is considered separately and estimated using the Green‐Ampt Mein‐Larson rainfall excess method. Pervious runoff temperature is estimated as the rainfall temperature. Field measurements indicate that wet bulb temperature can be used as a surrogate for rainfall temperature and that runoff temperatures from sod average just 2°C higher than rainfall temperatures. Differences between measured and predicted impervious runoff temperature average approximately 2°C, indicating that TURM is a useful tool for determining runoff temperatures for typical urban areas.     

COLD WATER PATCHES IN WARM STREAMS: PHYSICOCHEMICAL CHARACTERISTICS AND THE INFLUENCE OF SHADING1

ABSTRACT: Discrete cold water patches within the surface waters of summer warm streams afford potential thermal refuge for cold water fishes during periods of heat stress. This analysis focused on reach scale heterogeneity in water temperatures as influenced by local influx of cooler subsurface waters. Using field thermal probes and recording thermistors, we identified and characterized cold water patches (at least 3°C colder than ambient streamflow temperatures) potentially serving as thermal refugia for cold water fishes. Among 37 study sites within alluvial valleys of the Grande Ronde basin in northeastern Oregon, we identified cold water patches associated with side channels, alcoves, lateral seeps, and floodplain spring brooks. These types differed with regard to within floodplain position, area, spatial thermal range, substrate, and availability of cover for fish. Experimental shading cooled daily maximum temperatures of surface waters within cold water patches 2 to 4°C, indicating a strong influence of riparian vegetation on the expression of cold water patch thermal characteristics. Strong vertical temperature gradients associated with heating of surface layers of cold water patches exposed to solar radiation, superimposed upon vertical gradients in dissolved oxygen, can partially restrict suitable refuge volumes for stream salmonids within cold water patches.     

ESTIMATION OF WATER TEMPERATURE EXCEEDANCE PROBABILITIES USING THERMO-HYDRODYNAMIC MODELING1

ABSTRACT: A continuous simulation approach is proposed for estimating water temperature exceedance probabilities using thermo-hydrodynamic modeling. The approach uses (1) a deterministic unsteady flow and heat transport model, (2) continuous hydrological and meteorological data for a long historical period, and (3) synthetic records of tributary water temperatures and other model inputs. Representative historical records of streamflow, air temperatures, and other hydrometeorological variables are obtained from nearby gages. Stochastic modeling methods are used to construct synthetic records for other model inputs, including inflow water temperatures. An application of this deterministic-stochastic approach is presented for a complex waterway in northeastern Illinois with heat discharges from several power plants and wastewater treatment plants. Statistical results from the continuous simulations are compared to results obtained from traditional event simulations. The application illustrates the information that engineers and biologists can obtain for (1) evaluating compliance with water temperature standards, and (2) assessing the effect of water temperatures on aquatic habitat.     

Identifying stream temperature variation by coupling meteorological,hydrological, and water temperature models

In this study, we demonstrate a physically based semi-Lagrangian water temperature model known as the River Basin Model (RBM) coupled with the Variable Infiltration Capacity (VIC) hydrological model and Weather Research & Forecasting Model in the Mississippi River Basin (MRB). The results of this coupling compare favorably with observed water temperature data available from six river gages located in the MRB. Further sensitivity analysis indicates that the mean water temperatures may increase by 1.3, 1.5, and 1.8°C in northern, central, and southern MRB zones under a hypothetical uniform air temperature increase of 3.0°C. If air temperatures increase uniformly by 6.0°C in this scenario, then water temperatures are projected to increase by 3.3, 3.5, and 4.0°C. Lastly, downscaled air temperatures from a global climate model are used to drive the coupled VIC and RBM model from 2020 to 2099. Average stream temperatures from 2020 to 2099 increase by 1.0 to 8.0°C above 1950 to 2010 average water temperatures, with non-uniform increases along the river. In some portions of the MRB, stream temperatures could increase above survival thresholds for several native fish species, which are critical components of the stream ecosystem. In addition, increased water temperatures interact with nutrient loadings from sources throughout the MRB, which is expected to exacerbate harmful algal blooms and dead zones in the Gulf of Mexico.     

ESTIMATED CONSUMPTIVE LOSS FROM MAN-MADE SNOW1

ABSTRACT: Consumptive loss of water attributable to man-made snowmaking was estimated using an energy balance model and a mass balance procedure. Data from nine field experiments at Colorado ski areas were collected and used in these models. The mean consumptive loss using the energy balance model for the nine experiments was 6.0 percent and 5.8 percent for the mass balance model A thermodynamic relationship and a regression equation were developed to provide a procedure to estimate consumptive loss as a linear function of atmospheric temperature.     

A DECISION SUPPORT SYSTEM TO MANAGE SUMMER STREAM TEMPERATURES1

ABSTRACT: Warm summer stream temperatures due to low flows and high air temperatures are a critical water quality problem in many western United States river basins because they impact threatened fish species’habitat. One way to alleviate this problem is for local and federal organizations to purchase water rights to be used to increase flows, hence decrease temperatures. Presented is a Decision Support System (DSS) that can be used in an operations mode to effectively use water acquired to mitigate warm stream temperatures. The DSS uses a statistical model for predicting daily stream temperatures and a rule‐based module to compute reservoir releases. Water releases are calculated to meet fish habitat temperature targets based on the predicted stream temperature and a user specified confidence of the temperature predictions. Strategies that enable effective use of a limited amount of water throughout the season have also been incorporated in the DSS. The utility of the DSS is demonstrated by an example application to the Truckee River near Reno, Nevada, using hypothetical operating policy and 1988 through 1994 inflows. Results indicate that the DSS could substantially reduce the number of target temperature violations (i.e., stream temperatures exceeding the target temperature levels detrimental to fish habitat).     

ERRORS RELATED TO RANDOM STREAM TEMPERATURE DATA COLLECTION IN UPPER MISSISSIPPI RIVER WATERSHED1

ABSTRACT: Records of hourly water temperatures for two streams in the Upper Mississippi River basin were used to find the error between instantaneous measurements of stream water temperatures and true daily averages. The instantaneous summer water temperature measurements were assumed to be collected during daylight hours, and measurement times were selected randomly. The absolute error at the 95 percent confidence level of randomly collected stream water temperatures was less than 0.9°C for a 1 to 5m deep large river, but as large as 3.6°C for a 0.3 to lm deep small stream. Temperature readings of morning samples were usually below daily average values, and afternoon readings were usually above. Daily mean water temperatures were obtained with less than 0.23°C standard deviation from true daily averages if the daily maximum and minimum water temperatures were averaged. Sample results were obtained for the open water (summer) season only, since diurnal water temperature fluctuations in ice covered streams are usually negligible.     

TEMPERATURE EFFECTS ON GREAT LAKES WATER BALANCE STUDIES1

ABSTRACT. Beginning of month water temperature profiles are estimated for each lake. These water temperature profiles along with surface water temperatures are used to determine the effects of thermal expansion and contraction of water on the net basin supply values obtained from water balance studies using end of month lake levels. It is demonstrated that net basin supply values (equivalent to precipitation on the lake minus the evaporation from the lake plus the runoff into the lake) obtained from water balance studies without accounting for the thermal expansion and contraction of water may be in error by as much as 100 percent during some months for each lake.     

Thermodynamic coupling characteristics in hybrid (dry/wet) cooling system

A hybrid cooling system consisting of both a dry section and wet section is proposed in this paper as a means to conserving energy and water by combining the benefits of both dry and wet cooling modes. A new thermodynamic coupling characteristics computing model was established to identify the best combination of dry and wet cooling subsystems in the hybrid tower throughout year-round operation based on its air thermodynamic state under the “no plume” principle. A hybrid cooling tower in Inner Mongolia, China, consisting of an elliptical tube heat exchanger with rectangular fins and counter-flow wet packing, was designed as an example under the no plume principle. The minimum number of heat exchanger units in service and the corresponding thermodynamic operating parameters were obtained under a year-round operation. The tower exhibited notable advantages in regards to water conservation compared to the traditional evaporative cooling tower at an estimated yearly savings of 3.74 × 10⁷ kg water.     

Chitosan-supported palladium catalyst. IV. Influence of temperature on nitrophenol degradation and thermodynamic parameters

Glutaraldehyde cross-linked chitosan was loaded with palladium and then reduced using an in situ hydrogen generation procedure (Zn in sulfuric acid solution) to prepare a chitosan-supported palladium catalyst. This catalyst was successfully used to degrade nitrophenol in dilute solutions in the presence of sodium formate as the hydrogen donor. The influence of the initial concentration of nitrophenol and sodium formate was studied in order to determine the minimum molar ratio between these compounds required to achieve complete conversion of the nitrogenous product at two temperatures. Increasing the temperature decreased the excess of hydrogen donor required for complete conversion of nitrophenol. The temperature was also varied between 10 and 60 degrees C in order to determine the activation energy. The pseudo first-order equation was shown to fit degradation kinetics in most cases; however, for some cases it was necessary to use a variable-order equation to model the kinetics.     

ECOLOGICAL MANAGEMENT PROBLEMS CAUSED BY HEATED WASTE WATER DISCHARGE INTO THE AQUATIC ENVIRONMENT1

Discharge of heated waste water may affect the entire aquatic ecosystem–the interrelated biological, chemical, physical system–and, if the temperature change is large, may destroy the capacity of the ecosystem to serve a variety of beneficial purposes. However, it is possible to discharge heated waste water in carefully controlled amounts without seriously degrading the aquatic ecosystem. There are four basic alternatives which are open to us with regard to the heated waste water problem which we may choose singly or in various combinations: (1) Placing all heated, waste water in streams, lakes, and oceans without regard to the effects. Thus considering the environmental damage as a necessary consequence of our increased power demand. (2) Using, but not abusing, existing ecosystems. This means regulating the heated waste water discharge to fit the receiving capacity of the ecosystem. (3) Finding alternative ways to dissipate or beneficially use waste heat. (4) Modifying ecosystems to fit the new temperature conditions. We are all dependent upon a life-support system which is partly industrial and partly ecological. Unfortunately, we have reached a stage of development where the non-expandable, ecological portion of our life-support system is endangered by the expanding industrial portion. Optimal function and full beneficial use of both portions of our life-support system will only be possible if a variety of disciplines and diverse points of view can cooperate and work together effectively. Since wastes in amounts that are acceptable taken one at a time may be lethal collectively, environmental management should be on a regional basis.     

FRICTION SLOPE MODELS FOR M2 PROFILES1

ABSTRACT: Results of studies which have considered the relative merit of various friction slope averaging equations previously used in water surface profile computations are described. Limitations of the most accurate equation known for the M2 profile have indicated that a new equation which gives more emphasis to the upstream energy gradient is desirable. Based upon friction slope curves developed for M2 water surface profiles two new equations, one a parabolic and the other an elliptical approximation, are presented. The behavior of the new equations and of the previously most recommended equation is described by test calculations. The elliptical equation performed more satisfactorily than the harmonic method commonly recommended for M2 profile computations. Insertion of an additional cross-section about 50 feet upstream from a critical depth section was found to reduce computational errors for any energy gradient averaging method.     

A PRELIMINARY QUANTIFICATION OF THE IMPACTS OF ASPEN TO CONIFER SUCCESSION ON WATER YIELD - I. HEAT PULSE METHODOLOGY FOR MODEL CALIBRATION1

ABSTRACT: Twenty-six aspen (Populus tremuloides Michx.), 20 subalpine fir (Abies lasiocarps (Hook.) Nutt.), and 20 Engelmann spruce (Pices engelmanil (Parry) Engelm.) of various sizes were cut under water and suspended in permanent reserviors at a northern Utah site. The reservoirs were asealed so that all water loss was due to consumption by the trees. Sap velocities, as computed from heat pulse velocities, were related to conducting areas of the tree trunks. Computed transpiration volumes were then correlated with actual water losses from the reservoirs. Coefficients of determination (R²) of 0.87, 0.86, and 0.82 were obtained for the fir, aspen, and sprucs, respectively. Reservoir water loss for each species for each season was then used to adjust a plant activity index for computing transpiration within ASPCON, a model describing the hydrology of aspen to conifer succession. The plant activity index reflects the variation in the capability of a plant community to transpire water over the year. Assumptions and limitations of the heat pulse velocity technique are also outlined.     

Simulation of Temperature Mitigation by a Stormwater Detention Pond1

Abstract: A numerical model has been developed to simulate the hydraulic and heat transfer properties of a stormwater detention pond, as part of a simulation tool to evaluate thermal pollution of coldwater streams from stormwater runoff. The model is dynamic (unsteady) and based on principles of fluid mechanics and heat transfer. It is driven by hourly weather data, and specified inflow rates and temperatures. To calibrate and validate the pond model field data were collected on a commercial site in Woodbury, Minnesota. The relationship between pond inflow and outflow rates to precipitation was effectively calibrated using continuously recorded pond levels. Algorithms developed for surface heat transfer in lakes were found to be applicable to the pond with some modification, resulting in agreement of simulated and observed pond surface temperature within 1.0°C root mean square error. The use of an unshaded pond for thermal mitigation of runoff from paved surfaces was evaluated using the pond model combined with simulated runoff from an asphalt parking lot for six years of observed rainfall events. On average, pond outflow temperature was 1.2°C higher than inflow temperature, but with significant event‐to‐event variation. On average, the pond added heat energy to runoff from an asphalt parking lot. Although the pond added total heat energy to runoff, it did reduce the rate of heat outflow from the pond by an order of magnitude due to reductions in volumetric outflow rate compared with the inflow rate. By reducing the rate of heat flow, the magnitude of temperature impacts in a receiving stream were also reduced, but the duration of impacts was increased.     

重庆市应用湖库水水源热泵系统条件分析

通过对重庆市气候条件、湖库水水资源状况以及湖库水水温和水质分析,结果显示:重庆地区采用传统空气源热泵系统已不适宜,而采用水源热泵系统具有较高的节能优势。丰富的湖库水水资源量以及重庆市建筑沿湖库水而建特点,为在重庆市开展湖库水水源热泵系统创造便利条件;湖库水水温和水质基本能满足地表水水源热泵系统的水源要求;湖库水藻类易爆发,因此发展湖库水水源热泵主要解决的水质问题是藻类的堵塞问题。