An innovative example of herb residues recycling by gasification in a fluidized bed

A utilization way of herb residues is designed to convert herb residues to gas fuel in industrial-scale by a circulating fluidized bed gasifier in this paper. The product gas is used in the production of Chinese medicine, and the heat of the flue gas from the boiler can be used in herb residues drying to realize the energy recycling and no herb residues discharge. The gasification characteristics of herb residues in the circulating fluidized bed of 300 kg/h were investigated for about 200 h. The results indicated that the gas composition and tar yield were affected by biomass flow rate, equivalence ratio (ER), moisture content and char circulating. The lower heating value of product gas was 4–5 MJ/m³ using herb residues as feedstock. When mean biomass flow rate was at 5.5 kg m^?2 s^?1 and ER at 0.35, the product gas reached a good condition with lower heating value of 4.89 MJ/m³ and cold gas efficiency of 62.36%. When the moisture content changed from 12.5% to 18.7%, the concentrations of H₂, CO and CO₂ changed from 4.66% to 6.92%, 11.23% to 10.15%, and 16.55% to 17.82% respectively, and the tar content in gas decreased from 15.1 g/m³ to 14.4 g/m³ when the moisture content increased from 12.5% to 15.4%. There are metal oxides in the ash of herb residues, especially CaO, MgO, K₂O, Al₂O₃, and Fe₂O₃ which have obvious function on tar catalytic decomposition. The ash that attaches to the char particles can decrease the tar yield and improve the quality of gas after returning to the gasifier.     

Study on the influence of various factors in the hydrometallurgical processing of waste printed circuit boards for copper and gold recovery

The present lab-scale experimental study presents the process of leaching waste printed circuit boards (WPCBs) in order to recover gold by thioureation. Preliminary tests have shown that copper adversely affects gold extraction; therefore an oxidative leaching pre-treatment was performed in order to remove base metals. The effects of sulfuric acid concentration, hydrogen peroxide volume and temperature on the metal extraction yield were studied by analysis of variance (ANOVA). The highest copper extraction yields were 76.12% for sample A and 18.29% for sample D, after leaching with 2 M H₂SO₄, 20 ml of 30% H₂O₂ at 30 °C for 3 h. In order to improve Cu removal, a second leaching was performed only on sample A, resulting in a Cu extraction yield of 90%. Other experiments have shown the negative effect of the stirring rate on copper dissolution. The conditions used for the process of gold extraction by thiourea were: 20 g/L thiourea, 6 g/L ferric ion, 10 g/L sulfuric acid, 600 rpm stirring rate. To study the influence of temperature and particle size, this process was tested on pins manually removed from computer central processing units (CPUs) and on waste CPU for 3½ h. A gold extraction yield of 69% was obtained after 75% of Cu was removed by a double oxidative leaching treatment of WPCBs with particle sizes smaller than 2 mm.     

Pilot study on the advanced treatment of landfill leachate using a combined coagulation,fenton oxidation and biological aerated filter process

Mature landfill leachate is typically non-biodegradable. A combination process was developed that includes coagulation, Fenton oxidation, and biological aerated filtering to treat biologically-produced effluent. In this process, coagulation and Fenton oxidation were applied in order to reduce chemical oxygen demand (COD) organic load, and enhance biodegradability. Poly-ferric sulfate (PFS) at 600 mg l^?1 was found to be a suitable dosage for coagulation. For Fenton oxidation, an initial pH of 5, a total reaction time of 3 h, and an H₂O₂ dosage of 5.4 mmol l^?1, with a (H₂O₂)/n(Fe²⁺) ratio of 1.2 and two-step dosing were selected to achieve optimal oxidation. Under these optimal coagulation and Fenton oxidation conditions, the COD removal ratios were found to be 66.67% and 56%, respectively. Following pretreatment with coagulation and Fenton oxidation, the landfill leachate was further treated using a biological aerated filter (BAF). Our results show that COD was reduced to 75 mg l^?1, and the color was less than 10 degrees.     

Reclaiming the spent alkaline zinc manganese dioxide batteries collected from the manufacturers to prepare valuable electrolytic zinc and LiNi0.5Mn1.5O4 materials

A process for reclaiming the materials in spent alkaline zinc manganese dioxide (Zn–Mn) batteries collected from the manufacturers to prepare valuable electrolytic zinc and LiNi_0.5Mn_1.5O₄ materials is presented. After dismantling battery cans, the iron cans, covers, electric rods, organic separator, label, sealing materials, and electrolyte are separated through the washing, magnetic separation, filtrating, and sieving operations. Then, the powder residues react with H₂SO₄ (2 mol L^?1) solution to dissolve zinc under a liquid/solid ratio of 3:1 at room temperature, and subsequently, the electrolytic Zn with purity of ?99.8% is recovered in an electrolytic cell with a cathode efficiency of ?85% under the conditions of 37–40 °C and 300 A m^?2. The most of MnO₂ and a small quantity of electrolytic MnO₂ are recovered from the filtration residue and the electrodeposit on the anode of electrolytic cell, respectively. The recovered manganese oxides are used to synthesize LiNi_0.5Mn_1.5O₄ material of lithium-ion battery. The as-synthesized LiNi_0.5Mn_1.5O₄ discharges 118.3 mAh g^?1 capacity and 4.7 V voltage plateau, which is comparable to the sample synthesized using commercial electrolytic MnO₂. This process can recover the substances in the spent Zn–Mn batteries and innocuously treat the wastewaters, indicating that it is environmentally acceptable and applicable.     

Coal fly ash based carbons for SO2 removal from flue gases

Two different coal fly ashes coming from the burning of two coals of different rank have been used as a precursor for the preparation of steam activated carbons. The performance of these activated carbons in the SO₂ removal was evaluated at flue gas conditions (100 °C, 1000 ppmv SO₂, 5% O₂, 6% H₂O). Different techniques were used to determine the physical and chemical characteristics of the samples in order to explain the differences found in their behaviour. A superior SO₂ removal capacity was shown by the activated carbon obtained using the fly ash coming from a subbituminous–lignite blend. Experimental results indicated that the presence of higher amount of certain metallic oxides (Ca, Fe) in the carbon-rich fraction of this fly ash probably has promoted a deeper gasification in the activation with steam. A more suitable surface chemistry and textural properties have been obtained in this case which explains the higher efficiency shown by this sample in the SO₂ removal.     

Process development for recovery of copper and precious metals from waste printed circuit boards with emphasize on palladium and gold leaching and precipitation

A novel hydrometallurgical process was proposed for selective recovery of Cu, Ag, Au and Pd from waste printed circuit boards (PCBs). More than 99% of copper content was dissolved by using two consecutive sulfuric acid leaching steps in the presence of H₂O₂ as oxidizing agents. The solid residue of 2nd leaching step was treated by acidic thiourea in the presence of ferric iron as oxidizing agent and 85.76% Au and 71.36% Ag dissolution was achieved. The precipitation of Au and Ag from acidic thiourea leachate was investigated by using different amounts of sodium borohydride (SBH) as a reducing agent. The leaching of Pd and remained gold from the solid reside of 3rd leaching step was performed in NaClO-HCl-H₂O₂ leaching system and the effect of different parameters was investigated. The leaching of Pd and specially Au increased by increasing the NaClO concentration up to 10 V% and any further increasing the NaClO concentration has a negligible effect. The leaching of Pd and Au increased by increasing the HCl concentration from 2.5 to 5 M. The leaching of Pd and Au were endothermic and raising the temperature had a positive effect on leaching efficiency. The kinetics of Pd leaching was quite fast and after 30 min complete leaching of Pd was achieved, while the leaching of Au need a longer contact time. The best conditions for leaching of Pd and Au in NaClO-HCl-H₂O₂ leaching system were determined to be 5 M HCl, 1 V% H₂O₂, 10 V% NaClO at 336 K for 3 h with a solid/liquid ratio of 1/10. 100% of Pd and Au of what was in the chloride leachate were precipitated by using 2 g/L SBH. Finally, a process flow sheet for the recovery of Cu, Ag, Au and Pd from PCB was proposed.     

Application of response surface methodology to the advanced treatment of biologically stabilized landfill leachate using Fenton’s reagent

A Fenton process that uses FeCl₂ as the alternative catalyst was employed to deal with the biologically treated landfill leachate. Data obtained revealed that this Fenton process can provide an equivalent pollutant removal as the Fenton process that uses FeSO₄ as catalyst. Central composite design (CCD) and response surface methodology (RSM) were applied to evaluate and optimize the four key factors, namely initial pH, Fe(II) dosage ([Fe²⁺]), H₂O₂/Fe(II) mole ratio ([H₂O₂]/[Fe²⁺] ratio) and reaction time, which affect the performance of the Fenton treatment. Chemical oxygen demand (COD) and color were selected as response variables. This approach provided statistically significant quadratic models, which were adequate to predict responses and to carry out optimization under the conditions studied. It was demonstrated that the interaction between initial pH and [H₂O₂]/[Fe²⁺] ratio has a significant effect on the COD removal, while the interaction between [H₂O₂]/[Fe²⁺] ratio and reaction time shows a large impact on color removal. The optimal conditions were found to be initial pH 5.9, [Fe²⁺] = 9.60 mmol/L, [H₂O₂]/[Fe²⁺] ratio = 2.38, reaction time = 5.52 h. Under this optimal scheme, the COD and color in the effluent were reduced to 159 mg/L and 25°, respectively, with an increase of BOD₅/COD ratio from 0.05 to 0.21.     

Microbial oxygen uptake in sludge as influenced by compost physical parameters

The wide range of optimal values reported for the physical parameters of compost mixtures suggest that their interactive relationships should be investigated. The objective of this study was to examine the microbial O₂ uptake rate (OUR) in 16 sludge waste recipes, offering a range of moisture content (MC), waste/bulking agent (W/BA) ratio and BA particle size levels determined using a central composite experimental design. The 3 kg samples were maintained at a constant temperature and aeration rate for 28 days, during which a respirometer recorded O₂ uptake to provide a measure of microbial activity and biodegradability. The cumulative O₂ consumption after 14 and 28 days was found to be significantly influenced by MC, W/BA ratio, BA particle size and the interaction between MC and W/BA ratio (p < 0.05). Using multivariate regression analysis, the experimental data was used to generate a model with good predictive ability for cumulative O₂ consumption after 28 days as a function of the significant physical variables (R² = 0.84). The prediction of O₂ uptake by the model depended highly on the interaction between MC and W/BA ratio. A MC outside of the traditional 50–60% (wet basis) range still resulted in a high level of microbial O₂ uptake as long as the W/BA ratio was adjusted to maintain a suitable O₂ exchange in the sample. The evolution of OUR in the samples was also investigated, uncovering strong associations between short and long-term respirometric indices, such as peak OUR and cumulative O₂ consumption (p < 0.005). Combining peak OUR data with cumulative O₂ consumption after 14 days allowed for accurate predictions of cumulative O₂ after 28 days of aeration (R² = 0.96), implying that future studies need only run trials up to 14 days to evaluate the overall O₂ consumption or biodegradability of similar sludge mixtures.     

Quantifying methane oxidation in a landfill-cover soil by gas push–pull tests

Methane (CH₄) oxidation by aerobic methanotrophs in landfill-cover soils decreases emissions of landfill-produced CH₄ to the atmosphere. To quantify in situ rates of CH₄ oxidation we performed five gas push–pull tests (GPPTs) at each of two locations in the cover soil of the Lindenstock landfill (Liestal, Switzerland) over a 4 week period. GPPTs consist of the injection of a gas mixture containing CH₄, O₂ and noble gas tracers followed by extraction from the same location. Quantification of first-order rate constants was based upon comparison of breakthrough curves of CH₄ with either Ar or CH₄ itself from a subsequent inactive GPPT containing acetylene as an inhibitor of CH₄ oxidation. The maximum calculated first-order rate constant was 24.8 ± 0.8 h^?1 at location 1 and 18.9 ± 0.6 h^?1 at location 2. In general, location 2 had higher background CH₄ concentrations in vertical profile samples than location 1. High background CH₄ concentrations in the cover soil during some experiments adversely affected GPPT breakthrough curves and data interpretation. Real-time PCR verified the presence of a large population of methanotrophs at the two GPPT locations and comparison of stable carbon isotope fractionation of CH₄ in an active GPPT and a subsequent inactive GPPT confirmed that microbial activity was responsible for the CH₄ oxidation. The GPPT was shown to be a useful tool to reproducibly estimate in situ rates of CH₄ oxidation in a landfill-cover soil when background CH₄ concentrations were low.     

A novel process for recycling and resynthesizing LiNi1/3Co1/3Mn1/3O2 from the cathode scraps intended for lithium-ion batteries

To solve the recycling challenge for aqueous binder based lithium-ion batteries (LIBs), a novel process for recycling and resynthesizing LiNi_1/3Co_1/3Mn_1/3O₂ from the cathode scraps generated during manufacturing process is proposed in this study. Trifluoroacetic acid (TFA) is employed to separate the cathode material from the aluminum foil. The effects of TFA concentration, liquid/solid (L/S) ratio, reaction temperature and time on the separation efficiencies of the cathode material and aluminum foil are investigated systematically. The cathode material can be separated completely under the optimal experimental condition of 15 vol.% TFA solution, L/S ratio of 8.0 mL g^?1, reacting at 40 °C for 180 min along with appropriate agitation. LiNi_1/3Co_1/3Mn_1/3O₂ is successfully resynthesized from the separated cathode material by solid state reaction method. Several kinds of characterizations are performed to verify the typical properties of the resynthesized LiNi_1/3Co_1/3Mn_1/3O₂ powder. Electrochemical tests show that the initial charge and discharge capacities of the resynthesized LiNi_1/3Co_1/3Mn_1/3O₂ are 201 mAh g^?1 and 155.4 mAh g^?1 (2.8–4.5 V, 0.1 C), respectively. The discharge capacity remains at 129 mAh g^?1 even after 30 cycles with a capacity retention ratio of 83.01%.     

Treatment of mature landfill leachate by biofilters and Fenton oxidation

A series of processes by biofilter and Fenton oxidation to treat mature landfill leachate has been devised. At a hydraulic loading rate of 20 l m^?3 d^?1, a biofilter packed with aged refuse is found to remove 80% of chemical oxygen demand (COD), 89% of ammonia nitrogen and 96% of total phosphorus (TP). Particularly, TP levels dropped below 1 mg l^?1. The optimal condition for Fenton oxidation was selected to be an initial pH of 5, a dosage of 0.01 and 0.02 mol l^?1 of FeSO₄ and H₂O₂, respectively, and a duration of 3 h, where COD removal efficiency reaches 58.6%, and BOD₅/COD ratio is raised from 0.05 to 0.20. Subsequent treatment by a biofilter packed with slag reduces COD, ammonia nitrogen levels to less than 100, 25 mg l^?1, respectively. A pilot scale experiment conducted in situ demonstrates that this series of processes exhibits a high efficiency in removing pollutants from mature landfill leachate and it is viable for application.     

Evaluation of gold and silver leaching from printed circuit board of cellphones

Electronic waste has been increasing proportionally with the technology. So, nowadays, it is necessary to consider the useful life, recycling, and final disposal of these equipment. Metals, such as Au, Ag, Cu, Sn and Ni can be found in the printed circuit boards (PCB). According to this, the aims of this work is to characterize the PCBs of mobile phones with aqua regia; obtaining “reference” values of leaching, to gold and silver, with cyanide and nitric acid, respectively; and study the process of leaching of these metals in alternative leaching with sodium thiosulfate and ammonium thiosulfate. The metals were characterized by digesting the sample with aqua regia for 1 and 2 h at 60 °C and 80 °C. The leaching of Au with a commercial reagent (cyanide) and the Ag with HNO₃were made. The leaching of Au and Ag with alternative reagents: Na₂S₂O_3, and (NH₄)₂S₂O₃ in 0.1 M concentration with the addition of CuSO₄, NH₄OH, and H₂O₂, was also studied. The results show that the digestion with aqua regia was efficient to characterize the metals present in the PCBs of mobile phones. However, the best method to solubilize silver was by digesting the sample with nitric acid. The leaching process using sodium thiosulfate was more efficient when an additional concentration of 0.015 and 0.030 M of the CuSO₄ was added.     

Recovery of manganese oxides from spent alkaline and zinc–carbon batteries. An application as catalysts for VOCs elimination

Manganese, in the form of oxide, was recovered from spent alkaline and zinc–carbon batteries employing a biohydrometallurgy process, using a pilot plant consisting in: an air-lift bioreactor (containing an acid-reducing medium produced by an Acidithiobacillus thiooxidans bacteria immobilized on elemental sulfur); a leaching reactor (were battery powder is mixed with the acid-reducing medium) and a recovery reactor. Two different manganese oxides were recovered from the leachate liquor: one of them by electrolysis (EMO) and the other by a chemical precipitation with KMnO₄ solution (CMO). The non-leached solid residue was also studied (RMO). The solids were compared with a MnO_x synthesized in our laboratory.The characterization by XRD, FTIR and XPS reveal the presence of Mn₂O₃ in the EMO and the CMO samples, together with some Mn⁴⁺ cations. In the solid not extracted by acidic leaching (RMO) the main phase detected was Mn₃O₄.The catalytic performance of the oxides was studied in the complete oxidation of ethanol and heptane. Complete conversion of ethanol occurs at 200 °C, while heptane requires more than 400 °C. The CMO has the highest oxide selectivity to CO₂.The results show that manganese oxides obtained using spent alkaline and zinc–carbon batteries as raw materials, have an interesting performance as catalysts for elimination of VOCs.     

An advanced study on the hydrometallurgical processing of waste computer printed circuit boards to extract their valuable content of metals

This study refers to two chemical leaching systems for the base and precious metals extraction from waste printed circuit boards (WPCBs); sulfuric acid with hydrogen peroxide have been used for the first group of metals, meantime thiourea with the ferric ion in sulfuric acid medium were employed for the second one. The cementation process with zinc, copper and iron metal powders was attempted for solutions purification. The effects of hydrogen peroxide volume in rapport with sulfuric acid concentration and temperature were evaluated for oxidative leaching process. 2 M H₂SO₄ (98% w/v), 5% H₂O_2, 25 °C, 1/10 S/L ratio and 200 rpm were founded as optimal conditions for Cu extraction. Thiourea acid leaching process, performed on the solid filtrate obtained after three oxidative leaching steps, was carried out with 20 g/L of CS(NH₂)₂, 6 g/L of Fe³⁺, 0.5 M H₂SO₄, The cross-leaching method was applied by reusing of thiourea liquid suspension and immersing 5 g/L of this reagent for each other experiment material of leaching. This procedure has lead to the doubling and, respectively, tripling, of gold and silver concentrations into solution. These results reveal a very efficient, promising and environmental friendly method for WPCBs processing.     

Copper stabilization in beneficial use of waterworks sludge and copper-laden electroplating sludge for ceramic materials

A promising strategy for effectively incorporating metal-containing waste materials into a variety of ceramic products was devised in this study. Elemental analysis confirmed that copper was the predominant metal component in the collected electroplating sludge, and aluminum was the predominant constituent of waterworks sludge collected in Hong Kong. The use of waterworks sludge as an aluminum-rich precursor material to facilitate copper stabilization under thermal conditions provides a promising waste-to-resource strategy. When sintering the mixture of copper sludge and the 900 °C calcined waterworks sludge, the CuAl₂O₄ spinel phase was first detected at 650 °C and became the predominant product phase at temperatures higher than 850 °C. Quantification of the XRD pattern using the Rietveld refinement method revealed that the weight of the CuAl₂O₄ spinel phase reached over 50% at 850 °C. The strong signals of the CuAl₂O₄ phase continued until the temperature reached 1150 °C, and further sintering initiated the generation of the other copper-hosting phases (CuAlO₂, Cu₂O, and CuO). The copper stabilization effect was evaluated by the copper leachability of the CuAl₂O₄ and CuO via the prolonged leaching experiments at a pH value of 4.9. The leaching results showed that the CuAl₂O₄ phase was superior to the CuAlO₂ and CuO phases for immobilizing hazardous copper over longer leaching periods. The findings clearly indicate that spinel formation is the most crucial metal stabilization mechanism when sintering multiphase copper sludge with aluminum-rich waterworks sludge, and suggest a promising and reliable technique for reusing both types of sludge waste for ceramic materials.     

Evaluation of landfill leachate treatment by advanced oxidative process by Fenton’s reagent combined with membrane separation system

A high content of refractory organic matter, ammonia and toxic compounds is characteristic of landfill leachate. Advanced oxidative processes (AOPs) are an attractive alternative for landfill leachate treatment. However, when applied as a unique process treatment, they do not provide a complete solution for the effluent treatment. Combining AOP with a membrane separation process (MSP) presents a number of benefits and provides an adequate solution for this problem. With this in mind, the present work aims to evaluate, using a bench scale, leachate treatability through AOP by Fenton’s reagent (AOP/Fenton) combined with microfiltration (MF) and nanofiltration (NF). A high efficient removal of COD (63%), true color (76%) and humic substances (50%) was observed during AOP/Fenton under optimized conditions (1.7 g H₂O₂/g COD_{raw leachate}; FeSO₄·7H₂O:H₂O₂ = 1:5.3; pH = 3.8; reaction conditions = 115 rpm/28 min). According to the evaluated parameters, MSP presented an efficient complementary treatment, in which the integrity of the stages was sufficient for reaching regulatory levels in the effluent (Deliberação Normativa Conjunta COPAM/CERH-MG N^o. 1, May 5, 2008).     

Recovery of lithium and cobalt from waste lithium ion batteries of mobile phone

In view of the stringent environmental regulations, availability of limited natural resources and ever increasing need of alternative energy critical elements, an environmental eco-friendly leaching process is reported for the recovery of lithium and cobalt from the cathode active materials of spent lithium-ion batteries of mobile phones. The experiments were carried out to optimize the process parameters for the recovery of lithium and cobalt by varying the concentration of leachant, pulp density, reductant volume and temperature. Leaching with 2 M sulfuric acid with the addition of 5% H₂O₂ (v/v) at a pulp density of 100 g/L and 75 °C resulted in the recovery of 99.1% lithium and 70.0% cobalt in 60 min. H₂O₂ in sulfuric acid solution acts as an effective reducing agent, which enhance the percentage leaching of metals. Leaching kinetics of lithium in sulfuric acid fitted well to the chemical controlled reaction model i.e. 1 ? (1 ? X)^1/3 = k_ct. Leaching kinetics of cobalt fitted well to the model ‘ash diffusion control dense constant sizes spherical particles’ i.e. 1 ? 3(1 ? X)^2/3 + 2(1 ? X) = k_ct. Metals could subsequently be separated selectively from the leach liquor by solvent extraction process to produce their salts by crystallization process from the purified solution.     

High efficiency chlorine removal from polyvinyl chloride (PVC) pyrolysis with a gas–liquid fluidized bed reactor

In this research a gas–liquid fluidized bed reactor was developed for removing chlorine (Cl) from polyvinyl chloride (PVC) to favor its pyrolysis treatment. In order to efficiently remove Cl within a limited time before extensive generation of hydrocarbon products, the gas–liquid fluidized bed reactor was running at 280–320 °C, where hot N₂ was used as fluidizing gas to fluidize the molten polymer, letting the molten polymer contact well with N₂ to release Cl in form of HCl. Experimental results showed that dechlorination efficiency is mainly temperature dependent and 300 °C is a proper reaction temperature for efficient dechlorination within a limited time duration and for prevention of extensive pyrolysis; under this temperature 99.5% of Cl removal efficiency can be obtained within reaction time around 1 min after melting is completed as the flow rate of N₂ gas was set around 0.47–0.85 Nm³ kg^?1 for the molten PVC. Larger N₂ flow rate and additives in PVC would enhance HCl release but did not change the final dechlorination efficiency; and excessive N₂ flow rate should be avoided for prevention of polymer entrainment. HCl is emitted from PVC granules or scraps at the mean time they started to melt and the melting stage should be taken into consideration when design the gas–liquid fluidized bed reactor for dechlorination.     

Aluminium recovery vs. hydrogen production as resource recovery options for fine MSWI bottom ash fraction

Waste incineration bottom ash fine fraction contains a significant amount of aluminium, but previous works have shown that current recovery options based on standard on-step Eddy Current Separation (ECS) have limited efficiency. In this paper, we evaluated the improvement in the efficiency of ECS by using an additional step of crushing and sieving. The efficiency of metallic Al recovery was quantified by measuring hydrogen gas production. The ash samples were also tested for total aluminium content with X-ray fluorescence spectroscopy (XRF). As an alternative to material recovery, we also investigated the possibility to convert residual metallic Al into useful energy, promoting H₂ gas production by reacting metallic Al with water at high pH. The results show that the total aluminium concentration in the <4 mm bottom ash fraction is on average 8% of the weight of the dry ash, with less than 15% of it being present in the metallic form. Of this latter, only 21% can be potentially recovered with ECS combined with crushing and sieving stages and subsequently recycled. For hydrogen production, using 10 M NaOH at 1 L/S ratio results in the release of 6–11 l of H₂ gas for each kilogram of fine dry ash, equivalent to an energy potential of 118 kJ.