Organics removal from landfill leachate and activated sludge production in SBR reactors

This study is aimed at estimating organic compounds removal and sludge production in SBR during treatment of landfill leachate. Four series were performed. At each series, experiments were carried out at the hydraulic retention time (HRT) of 12, 6, 3 and 2d. The series varied in SBR filling strategies, duration of the mixing and aeration phases, and the sludge age. In series 1 and 2 (a short filling period, mixing and aeration phases in the operating cycle), the relationship between organics concentration (COD) in the leachate treated and HRT was pseudo-first-order kinetics. In series 3 (with mixing and aeration phases) and series 4 (only aeration phase) with leachate supplied by means of a peristaltic pump for 4h of the cycle (filling during reaction period) - this relationship was zero-order kinetics. Activated sludge production expressed as the observed coefficient of biomass production (Y(obs)) decreased correspondingly with increasing HRT. The smallest differences between reactors were observed in series 3 in which Y(obs) was almost stable (0.55-0.6 mg VSS/mg COD). The elimination of the mixing phase in the cycle (series 4) caused the Y(obs) to decrease significantly from 0.32 mg VSS/mg COD at HRT 2d to 0.04 mg VSS/mg COD at HRT 12d. The theoretical yield coefficient Y accounted for 0.534 mg VSS/mg COD (series 1) and 0.583 mg VSS/mg COD (series 2). In series 3 and 4, it was almost stable (0.628 mg VSS/mg COD and 0.616 mg VSS/mg COD, respectively). After the elimination of the mixing phase in the operating cycle, the specific biomass decay rate increased from 0.006 d(-1) (series 3) to 0.032 d(-1) (series 4). The operating conditions employing mixing/aeration or only aeration phases enable regulation of the sludge production. The SBRs operated under aerobic conditions are more favourable at a short hydraulic retention time. At long hydraulic retention time, it can lead to a decrease in biomass concentration in the SBR as a result of cell decay. On the contrary, in the activated sludge at long HRT, a short filling period and operating cycle of the reactor with the mixing and aeration phases seem the most favourable.     

Performance and Microbial Characteristics of Bioaugmentation Systems for Polyacrylamide Degradation

Efficient and reliable removal of polyacrylamide (PAM), which are present in oil extraction waste water, is critically important to prevent toxic discharges to receiving waters. In the present study, two PAM degrading bacterial strains, namely HWBI and HWBIII, were isolated from the activated sludge and soil in an oil field. Two sequencing batch reactors (SBRs) were bioaugmented with either HWBI or HWBIII and the performance of each bacteria for enhancing PAM removal was compared. The effects of bioaugmentation on the performance of the SBRs with different exogenous strains after a single inoculation were investigated under long term operation. Results showed that for the SBR augmented with HWBI, 70% of PAM was removed at the end of the first operation cycle, and the removal remained at approximately 70% in the following eight cycles after a single inoculation. For the SBR augmented with HWBIII, only 45% of the PAM was removed in the first cycle after the inoculation, and PAM removal decreased to 30% after eight cycles. Terminal restriction fragment length polymorphism (T-RFLP), a molecular screening technique, was applied to track the supplemented bacterial strains and to evaluate the effects of bioaugmentation on the microbial communities and to investigate the optimal bioaugmentation strategy.     

好氧颗粒污泥脱氮性能研究

研究了序批式反应器的污泥沉降时间、曝气速率、水力停留时间、进水方式等参数对好氧颗粒污泥的性能以及COD,NH4^*—N,TN去除率的影响。研究结果表明,在一个运行周期内,反应器运行工艺参数,如DO质量浓度和pH,具有一定的变化规律,并且其变化与反应器内各物质的转化存在严格的对应关系。因此,参照反应器运行工艺参数的特征点,对反应过程进行必要的控制,可达到较理想的处理效果。     

Organic and nitrogen removal from landfill leachate in aerobic granular sludge sequencing batch reactors

Granule sequencing batch reactors (GSBR) were established for landfill leachate treatment, and the COD removal was analyzed kinetically using a modified model. Results showed that COD removal rate decreased as influent ammonium concentration increasing. Characteristics of nitrogen removal at different influent ammonium levels were also studied. When the ammonium concentration in the landfill leachate was 366 mg L⁻¹, the dominant nitrogen removal process in the GSBR was simultaneous nitrification and denitrification (SND). Under the ammonium concentration of 788 mg L⁻¹, nitrite accumulation occurred and the accumulated nitrite was reduced to nitrogen gas by the shortcut denitrification process. When the influent ammonium increased to a higher level of 1105 mg L⁻¹, accumulation of nitrite and nitrate lasted in the whole cycle, and the removal efficiencies of total nitrogen and ammonium decreased to only 35.0% and 39.3%, respectively. Results also showed that DO was a useful process controlling parameter for the organics and nitrogen removal at low ammonium input.     

曝气-过滤一体化装置脱氮除磷的研究

曝气-过滤一体化装置将生物反应器与过滤机理有机结合,较好地维持了反应器中的高污泥浓度,实现了水力停留时间（HRT）与污泥停留时间的分离。采用连续流间歇曝气工艺对该装置的脱氮除磷效果进行了研究。实验结果表明：在HRT为8h,运行方式为曝气2h、停曝2h的条件下,COD去除率为95．55％,NH3-N未检出,TN为84．90％,TP为93．69％,出水各项指标都达到了GB8978-1996（污水综合排放标准》一级排放标准要求。     

Landfill leachate treatment using a rotating biological contactor and an upward-flow anaerobic sludge bed reactor

This paper describes the feasibility of an aerobic system (rotating biological contactor, RBC) and a biological anaerobic system (upward-flow anaerobic sludge bed reactor) at small scale for the treatment of a landfill leachate. In the first phase of the aerobic system study, a cyclic-batch RBC system was used to select perforated acetate discs among three different acetate disc configurations. These discs were chosen on the basis of high COD removal (65%) and biological stability. In the second phase, the RBC system (using four stages) was operated continuously at different hydraulic retention times (HRT), at different rotational speeds, and with varying organic concentrations of the influent leachate (2500-9000mgL(-1)). Forty percent of the total surface area of each perforated disc was submerged in the leachate. A COD removal of about 52% was obtained at an HRT of 24h and a rotational speed of 6rpm. For the anaerobic system, the reactor was evaluated with a volumetric organic load of 3273g-COD m(-3) day(-1) at an HRT of 54, 44, 39, 24 and 17h. At these conditions, the system reached COD removal efficiencies of 62%, 61%, 59%, 44% and 24%, respectively.     

Simultaneous removal of COD and ammonium from landfill leachate using an anaerobic-aerobic moving-bed biofilm reactor system

The performance of a moving-bed biofilm reactor (MBBR) system with an anaerobic-aerobic arrangement was investigated to treat landfill leachate for simultaneous removal of COD and ammonium. It was found that the anaerobic MBBR played a major role in COD removal due to methanogenesis, and the aerobic MBBR acted as COD-polishing and ammonium removal step. The contribution of the anaerobic MBBR to total COD removal efficiency reached 91% at an organic loading rate (OLR) of 4.08 kgCOD/(m3d), and gradually decreased to 86% when feed OLR was increased to 15.70 kgCOD/(m3d). Because of the complementary function of the aerobic reactor, the total COD removal efficiency of the system had a slight decrease from 94% to 92% even though the feed OLR was increased from 4.08 to 15.70 kgCOD/(m3d). Hydraulic retention time (HRT) had a significant effect on NH+4-N removal; more than 97% of the total NH+4-N removal efficiency could be achieved when the HRT of the aerobic MBBR was more than 1.25 days. The anaerobic-aerobic system had a strong tolerance to shock loading. A decrease in COD removal efficiency of only 7% was observed when the OLR was increased by four times and shock duration was 24 h, and the system could recover the original removal efficiency in 3 days. The average sludge yield of the anaerobic reactor was estimated to be 0.0538 gVSS/gCOD rem.     

Experimental study of behavior of endocrine-disrupting chemicals in leachate treatment process and evaluation of removal efficiency

An experimental study of the behavior of endocrine-disrupting chemicals (EDCs) in leachate treatment processes (aeration, coagulation and sedimentation, activated carbon adsorption, and advanced oxidation) was conducted and removal efficiencies were evaluated. Among target EDCs, concentrations of BPA (1800 times), DBP (10 times), BBP (40 times), and DEHP (30 times) in leachate are more than ten times higher than those in surface water. BPA, DBP, and BBP can be treated by aeration and DEHP, by advanced oxidation processes. BPA could not be effectively removed by coagulation and sedimentation because most of BPA partitioned in the supernatant. DEHP could hardly be treated by aeration. The removal ratios of DEHP were approximately 50–70% if the generated sediment was removed completely. The removal ratios of DEHP in leachate of 100 m³/d with 100 kg of activated carbon were 50–70%, assuming a complete mixing model. The concentration of DEHP was decreased to below one-tenth in 120 min by advanced oxidation processes.     

Anaerobic biotransformation and methane generation potential of cheese whey in batch and UASB reactors.

Anaerobic treatability and methane generation potential of cheese whey were determined in batch reactors. Furthermore, the effect of nutrient and trace metal supplementation on the batch anaerobic treatment, and the high-rate anaerobic treatability of cheese whey in upflow anaerobic sludge blanket (UASB) reactors were investigated. To this purpose biochemical methane potential experiments were conducted and single- and two-stage UASB reactors with granular cultures were operated. In UASB experiments significance of process staging, operational parameters such as hydraulic retention time (HRT), influent chemical oxygen demand (COD) concentration and loading rate were also investigated. The results revealed that nutrient and trace metal supplementation is vital for the anaerobic treatment of cheese whey; the anaerobic methane generation for the cheese whey studied was found to be 424 ml CH4/g COD (23.4 1 CH4/l cheese whey); undiluted cheese whey could be treated anaerobically at relatively short HRT values (2.06-4.95 days) without any significant stability problems; HRT values as low as 2-3 days can be used for the anaerobic treatment of cheese whey, with a COD removal efficiency of 95-97% at influent COD concentration of 42 700 +/- 141-55 100 +/- 283 mg/l.     

In situ nitrogen removal from leachate by bioreactor landfill with limited aeration

The feasibility of simultaneous nitrification and denitrification in a bioreactor landfill with limited aeration was assessed. Three column reactors, simulating bioreactor landfill operations under anaerobic condition (as reference), intermittent forced aeration and enhanced natural aeration were hence established, where aerated columns passed through two phases, i.e., fresh landfill and well-decomposed landfill. The experimental results show that limited aeration decreased nitrogen loadings of leachate distinctly in the fresh landfill. In the well-decomposed landfill, the NH(4)(+)-N of the input leachate could be nitrified completely in the aerated landfill columns. The nitrifying loadings of the column cross section reached 7.9 g N/m(2)d and 16.9 g N/m(2)d in the simulated landfill columns of intermittent forced aeration and enhanced natural aeration, respectively. The denitrification was influenced by oxygen distribution in the landfill column. Intermittent existence of oxygen in the landfill with the intermittent forced aeration was favorable to denitrify the NO(2)(-)-N and NO(3)(-)-N, indicated by the high denitrification efficiency (>99%) under the condition of BOD(5)/TN of more than 5.4 in leachate; locally persistent existence of oxygen in the landfill with enhanced natural aeration could limit the denitrification, indicated by relatively low denitrification efficiency of about 75% even when the BOD(5)/TN in leachate had an average of 7.1.     

Optimization of anaerobic digestion of municipal solid waste in combined process and sequential staging.

The optimization of anaerobic digestion aims to maximize organic waste stabilization after a short digestion period. This paper presents the optimization performance of the combined anaerobic digestion and sequential staging concept in a thermophilic, solid-state batch system as a treatment technology prior to landfill. The former involves enhanced pre-stage flushing with the addition of microaeration and inoculum in the methane phase. The latter involves leachate cross-recirculation between the mature and fresh waste reactors without conducting a pre-stage operation. The optimized process for combined anaerobic digestion showed that reducing the pre-stage operation with the maximum removal of organics from the waste bed is beneficial. Moreover, the sequential staging concept offers an improved process over the combined anaerobic digestion wherein the specific methane yield of 11.9 and 7.2 L CH4 kg(-1) volatile solids (VS) per day was achieved, respectively. After 28 days of operation, the sequential staging process showed an improved waste stabilization with 86 and 79% mass and volume reduction, respectively. A higher methane yield of 334 L CH4 kg(-1) VS with 86% VS reduction, which is equivalent to 84% process efficiency was obtained.     

Advanced physico-chemical treatment experiences on young municipal landfill leachates

In this study, Membrane Filtration (UF+RO), Struvite (MAP) precipitation and ammonia stripping alternatives were studied on biologically pre-treated Landfill Leachate. The results indicated that the system including the Upflow Anaerobic Sludge Blanket Reactor (UASBR) and Membrane Reactors (UF+RO) has been offered as an appropriate treatment alternative for young landfill leachates. This system provided high removals of COD, colour and conductivity (>98-99%). For ammonia removal, struvite precipitation was applied at the stoichiometric ratio (Mg:NH4:PO4=1:1:1) to anaerobically pre-treated raw landfill leachate effluent having an influent ammonium concentration of 2240 mg/l. Maximum ammonium nitrogen removal was observed as 85% at pH of 9.2. In ammonia stripping following 2 h of aeration, the removal was 72% at pH=12 while the removals were around 20% at pH=10 and pH=11. When membrane reactor, and struvite precipitation or ammonia stripping was applied to anaerobically pre-treated effluents, the results indicated that each system could be used as an appropriate post-treatment option for young landfill leachates. In economic aspect, ammonia stripping was found as the cheapest alternative with high ammonium removal. However, when both high COD and ammonium removals were to be achieved membrane technology such as UF+RO (SW) could be considered as the most appropriate system due to the fact that COD removal could be obtained very low by ammonia stripping.     

Anaerobic digestion of food waste: comparing leachate exchange rates in sequential batch systems digesting food waste and biosolids

Over 35,000 tonnes of food waste are generated from high concentration point sources (i.e., restaurants, hospitals and markets) in metropolitan Adelaide (Australia) each year. Anaerobic digestion is a preferred method of treatment to degrade highly putrescible waste streams such as food waste due its high methane potential. To maximise methane yield, a sequential batch anaerobic system was chosen as the most appropriate system. Two sets of sequential batch systems consisting of mature and start-up reactors in triplicate exchanged leachate. One set exchanged twice as much leachate by volume as the other set to determine the effects of different leachate exchange volumes. Results show that by increasing the leachate volume between mature and start-up reactors, the time to degrade feedstock decreases, but total methane generation yields did not markedly differ, being 229LCH4 kg(-1) VSadded and 214LCH4 kg(-1) VSadded. Process parameters used to determine when to cease leachate exchange in start-up reactors were a pH of 6.5 and methane generation rate of >0.5LCH4 kg(-1) VSadded day(-1). Changes in carbon dioxide and methane biogas composition in the mature reactors reflected process stress caused by the addition of leachate with high VFA concentrations from the start-up reactors and indicate there may be limits to leachate exchange rates and subsequent loading of mature reactors.     

Changes in carbon and nitrogen pool during in-situ aeration of old landfills under varying conditions

Emissions from old landfills via leachate and the gas phase are influenced by state and stability of the organic matter in the solid waste and by environmental conditions within the landfill. Remediation of landfills by means of in-situ aeration is one possibility to reduce these emissions. By establishing aerobic conditions, biological processes in the landfill are accelerated. To investigate the effects of this remediation technology, lab-scale experiments with column tests have been carried out. The main goal of the present work is to characterize the changes of the carbon and nitrogen compounds in the aerated solid waste, the leachate and the gas phase under varying conditions. The results demonstrate a clear reduction of emissions and a stabilization of the organic matter. Furthermore, it is shown that both the intensity of aeration and the amount of water affect biological processes to a certain extent. Even when columns were operated under anaerobic conditions after a long running period of aeration, the emissions remained low.     

Waste stabilization mechanism by a recirculatory semi-aerobic landfill with the aeration system

The main purpose of this research is to clarify and compare the mechanism of waste stabilization by a recirculatory semi-aerobic landfill with the aeration system. Our research is proposing the semi-aerobic landfill system for developing countries because of the simple and low-cost technology for the final disposal. Moreover, this system with leachate recirculation can be a more effective system for waste stabilization because of the improvement of leachate quality as an organic pollutant and, also, nitrogen removal. In this research, five different systems of landfill (Ae: aerobic, An: anaerobic, Se: semi-aerobic, SeR: recirculatory semi-aerobic landfill, and SeRA: recirculatory semi-aerobic landfill with aeration system) are compared with lysimeters which are 1 m high with a diameter of 0.3 m. The results of the leachate quality shows that the leachate treatment effect of the SeRA system can be observed to be as high as the Ae system. To determine the mechanism of this process, all lysimeters are dismantled after 1,100 days in the experimental period and the waste composition, the dissolution test, the mass balance of carbon and nitrogen, the determination of bacterial counts, etc., were analyzed. In this research, it was proven that the SeRA system has an optimal leachate treatment effect that is the same as the Ae system. And, from the results of the mass balance of carbon and nitrogen, the SeR and SeRA systems show higher waste stabilization effectiveness and nitrogen removal than the other systems. Moreover, the number of the aerobic bacteria can be observed to be higher in the SeR and SeRA systems. To determine these results, the waste stabilization mechanism is considered by the results of leachate quality, the mass balance of carbon and nitrogen, and, also, the bacterial numbers.     

The use of alum, ferric chloride and ferrous sulphate as coagulants in removing suspended solids, colour and COD from semi-aerobic landfill leachate at controlled pH.

Suspended solids, colour and chemical oxygen demand (COD) are among the main pollutants in landfill leachate. Application of physical or biological processes alone is normally not sufficient to remove these constituents, especially for leachate with a lower biochemical oxygen demand (BOD)/ COD ratio. The main objective of this research was to investigate the efficiency of coagulation and flocculation processes for removing suspended solids, colour and COD from leachate produced in a semi-aerobic landfill in Penang, Malaysia. A 12-month characterization study of the leachate indicated that it had a mean annual BOD/COD ratio of 0.15 and was partially stabilized, with little further biological degradation likely to occur. Particle size analysis of the raw leachate indicated that its 50th percentile (d50) was 11.68 microm. Three types of coagulants were examined in bench scale jar test studies: aluminium sulphate (alum), ferric chloride (FeCl3) and ferrous sulphate (FeSO4). The effects of agitation speed, settling time, pH, coagulant dosages and temperature were examined. At 300 rpm of rapid mixing, 50 rpm of slow mixing, and 60 min settling time, higher removals of suspended solids (over 95%), colour (90%) and COD (43%) were achieved at pH 4 and 12. FeCl3 was found to be superior to other coagulants tested. At pH 4 and 12, fair removal of suspended solids was observed at a reasonably low coagulant dose, i.e., 600 mg L(-1); hHowever, about 2500 mg L(-1) of coagulant was required to achieve good removals at pH 6. Better removals were achieved at higher temperature. The d50 of sludge after coagulation at pH 4 with a 2500 mg L(-1) FeCl3 dose was 60.16 microm, which indicated that the particles had been removed effectively from the leachate. The results indicate that coagulation and flocculation processes can be used effectively in integrated semi-aerobic leachate treatment systems, especially for removing suspended solids, colour and COD.     

Fundamental processes and implications during in situ aeration of old landfills

Results of investigations from many old landfills in Germany and Europe indicate that significant emissions occur under conventional landfill operating conditions (i.e., anaerobic conditions). Significant emissions via the gas phase are predicted to last at least three decades after landfill closure, while leachate emissions are predicted to continue for many decades, potentially even lasting for centuries. When considering the specific type and quality, and quite often lack of, protection barriers associated with old landfills, these leachate and gas emissions may result in a significant negative impact on the environment. However, complete sealing of the landfill only temporarily reduces emissions because dry-conservation of the biodegradable waste fraction results, thus not allowing any severe reduction in the emission and hazardous potential of the landfill to occur. If noticeable damage of the surface capping system occurred in these landfills, infiltrating water would restart the interrupted emission formation. In contrast, aerobic in situ stabilization by means of low pressure aeration attempts to stabilize and modify the inventory of organic matter inside the landfill, acting to reduce the emission potential in a more sustainable manner. By enabling faster and more extensive aerobic degradation processes in the landfill (compared with anaerobic processes), the organics (e.g., hydrocarbons) are degraded significantly faster, resulting in an increased carbon discharge via the gas phase, as well as reduced leachate concentrations. Because carbon dioxide (CO(2)) is the main compound in the extracted off-gas (instead of methane (CH(4)), which dominated under anaerobic landfill conditions), the negative impact of diffuse LFG emissions towards an increased global warming effect may be significantly lowered. With respect to leachate quality, a reduction of organic compounds as well as ammonia-nitrogen can be expected. In addition to these positive ecological effects, aerobic in situ stabilization is associated with significant cost savings potential due to both quantitative and qualitative reductions in the aftercare period. This paper describes the fundamental processes and implications of in situ landfill aeration. Additionally, possible criteria for defining an endpoint of the active aeration process are presented and discussed.     

Different treatment strategies for highly polluted landfill leachate in developing countries

The aim of this research was to determine appropriate treatment technique for effective treatment of heavily polluted landfill leachate. We accomplished several treatment experiments: (i) aerobic biological treatment, (ii) chemical coagulation, (iii) advanced oxidation process (AOP) and (iv) several combined treatment strategies. Efficiency of these treatment procedures were monitored by analysing COD and colour removal. Leachate used for this study was taken from Matuail landfill site at Dhaka city. With extended aeration process which is currently used in Matuail landfill site for leachate treatment, maximum COD and colour removal of 36% and 20%, respectively could be achieved with optimum retention period of 7days. With optimum aluminium sulphate dose of 15,000mg/L and pH value of 7.0, maximum COD and colour removals of 34% and 66%, respectively were observed by using chemical coagulation. With optimum pH of 5.0 and optimum dosages of reagents having H(2)O(2)/Fe(2+) molar ratio of 1.3 the highest removal of COD and colour were found 68% and 87%, respectively with sludge production of 55%. Fenton treatment which is an advanced oxidation process was the most successful between these three separate treatment procedures. Among the combined treatment options performed, extended aeration followed by Fenton method was the most suitable one.     

Emission of volatile sulfur compounds during composting of municipal solid waste (MSW)

Volatile sulfur compounds (VSCs) are the main source for malodor from composting plants. In this study, the VSCs generated from composting of 15–80 mm municipal solid waste (T0), kitchen waste (T1) and kitchen waste mixed dry cornstalks (T2) were measured in 60 L reactors with forced aeration for a period of 30 days. The VSCs detected in all treatments were hydrogen sulfide (H₂S), methyl mercaptan (MM), dimethyl sulfide (DMS), carbon bisulfide (CS₂) and dimethyl disulfide (DMDS). Over 90% of the VSCs emissions occurred during the first 15 days, and reached their peak values at days 4–7. The emission profiles of five VSCs species were significantly correlated with internal materials temperature and outlet O₂ concentration (p < 0.05). Total emissions of the VSCs were 216.1, 379.3 and 126.0 mg kg^?1 (dry matter) for T0, T1 and T2, respectively. Among the five VSCs, H₂S was the most abundant compound with 39.0–43.0% of total VSCs released. Composting of kitchen waste from separate collection posed a negative influence on the VSC and leachate production because of its high moisture content. An addition of dry cornstalks at a mixing ratio of 4:1 (wet weight) could significantly reduce the VSCs emissions and avoid leachate. Compared to pure kitchen waste, VSCs were reduced 66.8%.     

无机条件下硫酸盐型厌氧氨氧化反应的特性

在循环流厌氧反应器中研究了无机条件下采用厌氧颗粒污泥启动硫酸盐型厌氧氨氧化(S-ANAMMOX)的反应特性。结果表明:在1~124 d的运行时间内,从第37天开始出现了NH4+-N和SO_4~(2-)的同步去除,生成NO_2~-,NO_3~-,反应最终产物为N2和单质硫,NH4+-N和SO_4~(2-)的最高去除率分别达到92.47%和59.3%;当进水nN∶nS较高时,能显著提高NH4+-N去除率和总氮去除率;SO_4~(2-)与NH4+发生氧化还原反应产生NO2-和NO3-是pH降低的过程;进水nN∶nS、进水平均NH_4~+-N、SO_4~(2-)质量浓度和HRT均对S-ANAMMOX反应的氮硫转化比有一定影响,表明S-ANAMMOX反应是一个多步反应。