2015年南京市PM2.5与PM10的污染特征

分析了2015年南京市PM2.5和PM10的浓度特征和大致来源类型。PM2.5和PM10的年均浓度分别为56.6 μg·m-3和96.5 μg·m-3,污染水平较高。颗粒物浓度的季节变化特征一致：冬 > 春 > 秋 > 夏;PM2.5的日变化呈"单峰单谷"型,而PM10的呈"单峰双谷"型。颗粒物浓度在城区高于郊区;植被茂盛区域的浓度较低。对PM2.5/PM10而言,比值在冬季和梅雨期较大,分别受取暖和降水的影响;比值在春季和夏末秋初较小,分别受沙尘和秸秆焚烧的影响。PM2.5多为二次颗粒物,PM10多为一次颗粒物;固定污染源对PM2.5的间接贡献和对PM10的直接贡献较移动污染源而言更大。     

Identification of dicarboxylic acids and aldehydes of PM10 and PM2.5 aerosols in Nanjing,China

In this study aerosol samples of PM10 and PM2.5 collected from 18 February 2001 to 1 May 2001 in Nanjing, China were analyzed for their water-soluble organic compounds. A series of homologous dicarboxylic acids (C_2–10) and two kinds of aldehydes (methylglyoxal and 2-oxo-malonaldehyde) were detected by GC and GC/MS. Among the identified compounds, the concentration of oxalic acid was the highest at all the five sites, which ranged from 178 to 1423 ng/m³. The second highest concentration of dicarboxylic acids were malonic and succinic acids, which ranged from 26.9 to 243 ng/m³. Higher level of azelaic acid was also observed, of which the maximum was 301 ng/m³. As the highest fraction of dicarboxylic acids, oxalic acid comprised from 28% to 86% of total dicarboxylic acids in PM10 and from 41% to 65% of total dicarboxylic acids in PM2.5. The dicarboxylic acids (C₂, C₃, C₄) together accounted for 38–95% of total dicarboxylic acids in PM10 and 59–87% of dicarboxylic acids in PM2.5. In this study, the total dicarboxylic acids accounted for 2.8–7.9% of total organic carbon (TOC) of water-soluble matters for PM10 and 3.4–11.8% of TOC for PM2.5. All dicarboxylic acids detected in this study together accounted for about 1% of particle mass. The concentration of azelaic acid was higher at one site than others, which may be resulted from higher level of volatile fat used for cooking. The amounts of dicarboxyic acids (C_2,3,4,9) and 2-oxo-malonaldehyde of PM2.5 were higher in winter and lower in spring. Compared with other major metropolitans in the world, the level of oxalic acid concentration of Nanjing is much higher, which may be contributed to higher level of particle loadings, especially for fine particles.     

PM10 and PM2.5 source apportionment in the Barcelona Metropolitan area, Catalonia, Spain

Levels of total suspended particles, PM10, PM2.5 and PM1 were continuously monitored at an urban kerbside in the Metropolitan area of Barcelona from June 1999 to June 2000. The results show that hourly levels of PM2.5 and PM1 are consistent with the daily cycle of gaseous pollutants emitted by traffic, whereas TSP and PM10 do not follow the same trend, at least in the diurnal period. The PM2.5/PM10 ratio is dependent on the traffic emissions, whereas additional contribution sources for the >10 μm fraction must be taken into account in the diurnal period. Different PM10 and PM2.5 source apportionment techniques were compared. A methodology based on the chemical determination of 83% of both PM10 and PM2.5 masses allowed us to quantify the marine (4% in PM10 and <1% in PM2.5), crustal (26% in PM10 and 8% in PM2.5) and anthropogenic (54% in PM10 and 73% in PM2.5) loads. Peaks of crustal contribution to PM10 (up to 44% of the PM10 mass) were recorded under Saharan air mass intrusions. A different seasonal trend was observed for levels of sulphate and nitrate, probably as a consequence of the different thermodynamic behaviour of these PM species and the higher summer oxidation rate of SO₂.     

Airborne particle PM2.5/PM10 mass distribution and particle-bound PAH concentrations near a medical waste incinerator

This study attempts to determine the influence of air quality in a residential area near a medical waste incineration plant. Ambient air concentrations of polycyclic aromatic hydrocarbons (PAHs), PM₁₀ and PM_2.5 (PM—particulate matter) were determined by collecting air samples in areas both upwind and downwind of the plant. The differences in air pollutant levels between the study area and a reference area 11 km away from the plant were evaluated.Dichotomous samplers were used for sampling PM_2.5 and PM₁₀ from ambient air. Two hundred and twenty samples were obtained from the study area, and 100 samples were taken from a reference area. Samples were weighed by an electronic microbalance and concentrations of PM_2.5 and PM₁₀ were determined. A HPLC equipped with a fluorescence detector was employed to analyze the concentrations of 15 PAHs compounds adsorbed into PM_2.5 and PM₁₀.The experimental results indicated that the average concentrations of PM_2.5 and PM₁₀ were 30.34±17.95 and 36.81±20.45 μg m⁻³, respectively, in the study area, while the average ratio of PM_2.5/PM₁₀ was 0.82±0.01. The concentrations of PM_2.5 and PM₁₀ of the study area located downwind of the incinerator were significantly higher than the study area upwind of the incinerator (P<0.05).The concentration of PAHs in PM_2.5 in the study area was 2.2 times higher than in the reference area (P<0.05). Furthermore, the benzo(a)pyrene concentrations in PM_2.5 and PM₁₀ were 0.11±0.05 ng m⁻³ and 0.12±0.06 ng m⁻³ in the study area, respectively. The benzo(a)pyrene concentrations of PM_2.5 and PM₁₀ in the study area were 7 and 5.3 times higher than in the reference area (P<0.05), respectively.The study indicated that the air quality of PM_2.5, PM₁₀ and PAHs had significant contamination by air pollutants emitted from a medical waste incineration factory, representing a public health problem for nearby residences, despite the factory being equipped with a modern air pollution control system.     

Elemental composition of PM10 and PM2.5 in urban environment in South Brazil

The purpose of the present study is to analyze the elemental composition and the concentrations of PM₁₀ and PM_2.5 in the Guaíba Hydrographic Basin with HV PM₁₀ and dichotomous samplers. Three sampling sites were selected: 8° Distrito, CEASA and Charqueadas. The sampling was conducted from October 2001 to December 2002. The mass concentrations of the samplers were evaluated, while the elemental concentrations of Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu and Zn were determined using the Particle-Induced X-ray Emission (PIXE) technique. Factor Analysis and Canonical Correlation Analysis were applied to the chemical and meteorological variables in order to identify the sources of particulate matter. Industrial activities such as steel plants, coal-fired power plants, hospital waste burning, vehicular emissions and soil were identified as the sources of the particulate matter. Concentration levels higher than the daily and the annual average air quality standards (150 and 50 μg m⁻³, respectively) set by the Brazilian legislation were not observed.     

天津大气PM_(2.5)中碳组分特征和来源分析

于2014年1—4月在天津城区采集PM2.5样品,采用热光反射法测定样品中有机碳(OC)、元素碳(EC)及8个碳组分(OC1、OC2、OC3、OC4、EC1、EC2、EC3、裂解碳(OP))的含量。结果表明,天津城区空气PM2.5中OC、EC质量浓度分别为(18.7±9.9)、(3.9±2.6)μg/m3,两者之和占PM2.5质量浓度的18.0%。采样期间OC与EC变化趋势一致,均呈现春节期间、普通采暖季浓度较高,非采暖季浓度较低的特点。对8个碳组分进行相关性分析,发现OC1~OC4及EC1~EC3分别来自相似的来源或受大气中类似的二次过程影响,主成分分析结果表明,燃煤、生物质燃烧和机动车排放对天津城区PM2.5中碳组分贡献显著。     

Particulate matter in California: part 1--Intercomparison of several PM2.5, PM10-2.5, and PM10 monitoring networks

It will be many years before the recently deployed network of fine particulate matter with an aerodynamic diameter less than 2.5 microm (PM2.5) Federal Reference Method (FRM) samplers produces information on nonattainment areas, trends, and source impacts. However, data on PM2.5 and its major constituents have been routinely collected in California for the past 20 years. The California Air Resources Board operated as many as 20 dichotomous (dichot) samplers for PM2.5 and coarse PM (PM10-2.5). The California Acid Deposition Monitoring Program (CADMP) collected 12-h-average PM2.5 and PM10 from 1988 to 1995 at ten urban and rural sites and 24-h-average PM2.5 at five urban sites since 1995. Beginning in 1994, the Children's Health Study collected 2-week averages of PM2.5 in 12 communities in southern California using the Two-Week Sampler (TWS). Comparisons of collocated samples establish relationships between the dichot, CADMP, and TWS samplers and the 82-site network of PM2.5 FRM samplers deployed since 1999 in California. PM mass data from the different monitoring programs have modest to high correlation to FRM mass data, fairly small systematic biases and negative proportional biases ranging from 7 to 22%. If the biases are taken into account, all of the programs should be considered comparable with the FRM program. Thus, historical data can be used to develop long-term PM trends in California.     

Particulate matter in California: part 2--Spatial, temporal, and compositional patterns of PM2.5, PM10-2.5, and PM10

Geographic and temporal variations in the concentration and composition of particulate matter (PM) provide important insights into particle sources, atmospheric processes that influence particle formation, and PM management strategies. In the nonurban areas of California, annual-average PM2.5 and PM10 concentrations range from 3 to 10 microg/m3 and from 5 to 18 microg/m3, respectively. In the urban areas of California, annual-averages for PM2.5 range from 7 to 30 microg/m3, with observed 24-hr peaks reaching levels as high as 160 microg/m3. Within each air basin, exceedances are a mixture of isolated events as well as periods of elevated PM2.5 concentrations that are more prolonged and regional in nature. PM2.5 concentrations are generally highest during the winter months. The exception is the South Coast Air Basin, where fairly high values occur throughout the year. Annual-average PM2.5 mass, as well as the concentrations of major components, declined from 1988 to 2000. The declines are especially pronounced for the sulfate (SO4(2-)) and nitrate (NO3-) components of PM2.5 and PM10) and correlate with reductions in ambient levels of oxides of sulfur (SOx) and oxides of nitrogen (NOx). Annual averages for PM10-2.5 and PM10 exhibited similar downwind trends from 1994 to 1999, with a slightly less pronounced decrease in the coarse fraction.     

PM2.5–10, PM2.5 and associated water-soluble inorganic species at a coastal urban site in the metropolitan region of Rio de Janeiro

The concentrations of PM_2.5−10, PM_2.5 and associated water-soluble inorganic species (WSIS) were determined in a coastal site of the metropolitan region of Rio de Janeiro, Southeastern Brazil, from October 1998 to September 1999 (n=50). Samples were dissolved in water and analyzed for major inorganic ions. The mean (± standard deviation; median) concentrations of PM_2.5−10 and PM_2.5 were, respectively, 26 (± 16; 21) μg m⁻³ and 17 (± 13; 14) μg m⁻³. Their mean concentrations were 1.7–1.8 times higher in dry season (May–October) than in rainy season (November–April). The WSIS comprised, respectively, 34% and 28% of the PM_2.5−10 and PM_2.5 masses. Chloride, Na⁺ and Mg²⁺ were the predominant ions in PM_2.5−10, indicating a significant influence of sea-salt aerosols. In PM_2.5, SO₄²⁻ (∼97% nss-SO₄²⁻) and NH₄⁺ were the most abundant ions and their equivalent concentration ratio (SO₄²⁻/NH₄⁺ ∼1.0) suggests that they were present as (NH₄)₂SO₄ particles. The mean concentration of (NH₄)₂SO₄ was 3.4 μg m⁻³. The mean equivalent PM_2.5 NO₃⁻ concentration was eight times smaller than those of SO₄²⁻ and NH₄⁺. The PM_2.5 NO₃⁻ concentration in dry season was three times higher than in rainy season, probably due to reaction of NaCl (sea salt) with HNO₃ as a result of higher levels of NO_y during the dry season and/or reduced volatilization of NH₄NO₃ due to lower wintertime temperature. Chloride depletion was observed in both size ranges, although more pronouncely in PM_2.5.     

Trends in arsenic levels in PM10 and PM2.5 aerosol fractions in an industrialized area

Arsenic is a toxic element that affects human health and is widely distributed in the environment. In the area of study, the main Spanish and second largest European industrial ceramic cluster, the main source of arsenic aerosol is related to the impurities in some boracic minerals used in the ceramic process. Epidemiological studies on cancer occurrence in Spain points out the study region as one with the greater risk of cancer. Concentrations of particulate matter and arsenic content in PM₁₀ and PM_2.5 were measured and characterized by ICP-MS in the area of study during the years 2005–2010. Concentrations of PM₁₀ and its arsenic content range from 27 to 46 μg/m³ and from 0.7 to 6 ng/m³ in the industrial area, respectively, and from 25 to 40 μg/m³ and from 0.7 to 2.8 ng/m³ in the urban area, respectively. Concentrations of PM_2.5 and its arsenic content range from 12 to 14 μg/m³ and from 0.5 to 1.4 ng/m³ in the urban background area, respectively. Most of the arsenic content is present in the fine fraction, with ratios of PM_2.5/PM₁₀ in the range of 0.65–0.87. PM₁₀, PM_2.5, and its arsenic content show a sharp decrease in recent years associated with the economic downturn, which severely hit the production of ceramic materials in the area under study. The sharp production decrease due to the economic crisis combined with several technological improvements in recent years such as substitution of boron, which contains As impurities as raw material, have reduced the concentrations of PM₁₀, PM_2.5, and As in air to an extent that currently meets the existing European regulations.     

Use of the aerodynamic particle sizer to measure ambient PM10-2.5: the coarse fraction of PM10

The Aerodynamic Particle Sizer (APS 3321, TSI, Inc., Shoreview, MN) rapidly measures particle number concentration by size from 0.5 to 20 microm. This work used simple assumptions for particle shape factor and density to estimate ambient coarse mode particulate matter, PM10-2.5, from APS number concentration data. This estimate was compared with that measured with time-integrated, filter-based federal reference method (FRM) samplers in four U.S. field studies: two in Phoenix, AZ; one in Gary, IN; and one in Riverside, CA. Near one-to-one agreement and a strong linear relationship were observed between APS-estimated and FRM-measured PM10-2.5 in the first Phoenix, AZ study (slope = 0.90, R2 = 1.00); the second Phoenix, AZ study (slope = 0.99, R2 = 0.99); and the Riverside, CA study (slope = 1.00, R2 = 0.84). In the Gary, IN study, PM10-2.5 estimates made with data from the APS tended to be less than that measured with the FRM samplers (slope = 0.57), but the linear relationship between the two methods was still strong (R2 = 0.90). Particle-bound water associated with wet atmospheric conditions may account for these differences. Additional testing is required to resolve this issue.     

南京仙林地区大气PM2.5中金属化学形态分析及其风险评估

采用四步连续提取法提取不同季节南京仙林地区PM_(2.5)中不同化学形态的金属组分。结果显示:(1)PM_(2.5)日均值平均为84.93μg/m3,75%的样品超过了《环境空气质量标准》(GB 3095—2012)中PM_(2.5)日均值二级标准值(75μg/m~3)。(2)PM_(2.5)中Fe、Zn和Pb浓度最高,As和Cd浓度最低。(3)Zn、Cd和Mn主要以弱酸提取态(F1)存在,Pb以可还原态(F2)为主,As主要以F1和F2存在,Ni和Cr以F1和可氧化态(F3)为主,Cu主要为F1、F2、F3,Fe和Ti大部分以残渣态(F4)存在。(4)Zn具有非常高的环境风险,Cd、As、Cu和Mn均表现出高风险,Pb、Ni和Cr具有中等风险,Fe、Ti具有低风险。(5)对于儿童,Cr具有潜在致癌风险;对于成人,As和Cr具有潜在致癌风险。     

Organic and elemental carbon associated to PM10 and PM2.5 at urban sites of northern Greece

Organic carbon (OC) and elemental carbon (EC) concentrations, associated to PM₁₀ and PM_2.5 particle fractions, were concurrently determined during the warm and the cold months of the year (July–September 2011 and February–April 2012, respectively) at two urban sites in the city of Thessaloniki, northern Greece, an urban-traffic site (UT) and an urban-background site (UB). Concentrations at the UT site (11.3?±?5.0 and 8.44?±?4.08 14 μg m^?3 for OC₁₀ and OC_2.5 vs. 6.56?±?2.14 and 5.29?±?1.54 μg m^?3 for EC₁₀ and EC_2.5) were among the highest values reported for urban sites in European cities. Significantly lower concentrations were found at the UB site for both carbonaceous species, particularly for EC (6.62?±?4.59 and 5.72?±?4.36 μg m^?3 for OC₁₀ and OC_2.5 vs. 0.93?±?0.61 and 0.69?±?0.39 μg m^?3 for EC₁₀ and EC_2.5). Despite that, a negative UT-UB increment was frequently evidenced for OC_2.5 and PM_2.5 in the cold months possibly indicative of emissions from residential wood burning at the urban-background site. At both sites, cconcentrations of OC fractions were significantly higher in the cold months; on the contrary, EC fractions at the UT site were prominent in the warm season suggesting some influence from maritime emissions in the nearby harbor area. Secondary organic carbon, being estimated using the EC tracer method and seasonally minimum OC/EC ratios, was found to be an appreciable component of particle mass particularly in the cold season. The calculated secondary contributions to OC ranged between 35 and 59 % in the PM₁₀ fraction, with relatively higher values in the PM_2.5 fraction (39–61 %). The source origin of carbonaceous species was investigated by means of air parcel back trajectories, satellite fire maps, and concentration roses. A local origin was mainly concluded for OC and EC with limited possibility for long range transport of biomass (agricultural waste) burning aerosol.     

Atmospheric concentrations of PM2.5 trace elements in the Seoul urban area of South Korea

Fine particles (PM2.5) were collected during all four seasons, from April 2001 to February 2002, in Seoul, South Korea, using an annular denuder system. Elemental compositions of ambient PM2.5 were analyzed using the proton-induced X-ray emission method. The greatest contributors (> or = 2%) to the PM2.5 mass were sulfur (S), silicon (Si), chlorine (Cl), aluminum (Al), and iron (Fe) in the spring; S in the summer; and S and Cl in the fall. S, Cl, and Si were the major elements in the winter. S was the most abundant species among the elements, ranging from 5.3 to 7.9%, followed by Si and Cl. From analysis of variance, PM2.5 mass, Al, Si, potassium, calcium, and Fe showed significant seasonal differences during the four seasons (p < 0.001). Enrichment factor (EF) analysis was carried out to identify the sources affecting the aerosol in the Seoul area. On the basis of the mean EF values, elemental S, copper, zinc, and lead may be emitted from anthropogenic sources (EF > 50). Elemental Al, Si, titanium, and Fe may be emitted from crustal sources (EF < 3). Additionally, a correlation analysis was carried out for source identification. The results of the correlation analysis were confirmed by the results of the EF analysis.     

A four-year size-segregated characterization study of particles PM10, PM2.5 and PM1 depending on air mass origin at Melpitz

PM₁₀ measurements were started in November 1992 at Melpitz site. The mean PM₁₀ concentration in 1993 was 38 μg m^?3 in the summer season (May until October) and about 44 μg m^?3 in the winter season (November until April). The mean PM₁₀ level decreased until 1999 and varies now in ranges from 20–34 μg m^?3 to 17–24 μg m^?3 (minimum and maximum mean values for 1999–2008) in winter and summer seasons, respectively. High volume filter samples of particles PM₁₀, PM_2.5 and PM₁ were characterized for mass, water-soluble ions, organic and elemental carbon from 2004 until 2008. The percentage of PM_2.5 in PM₁₀ varies between summer (71.6%) and winter seasons (81.9%). Mean concentrations of PM₁₀, PM_2.5 and PM₁ in Melpitz were 20, 15, and 13 μg m^?3 in 2004, 22, 18, and 13 μg m^?3 in 2005, 24, 19, and 12 μg m^?3 in 2006 and 22, 17, and 12 μg m^?3 in 2007, respectively. In the four winters the rural background concentration PM₁₀ at Melpitz exceeded the daily 50 μg m^?3 limit for Europe on 8, 8, 7 and 6 days, respectively.Findings for a simple two-sector-classification of the samples (May 2004 until April 2008) using 96-h backward trajectories for the identification of source regions are: Air masses were transported most of time (60%) from the western sector and secondly (17%) from the eastern sector. The lowest daily mean mass concentration PM₁₀ were found during western inflow in summer (17 μg m^?3) containing low amounts of sulphate (2.4 μg m^?3), nitrate (1.7 μg m^?3), ammonium (1.1 μg m^?3) and TC (3.7 μg m^?3). In opposite the highest mean mass concentration PM₁₀ was found during eastern inflow in winter (35 μg m^?3) with high amounts of sulphate (6.1 μg m^?3), nitrate (5.4 μg m^?3), ammonium (3.8 μg m^?3) and TC (9.4 μg m^?3). An estimation of secondary formed OC (SOA) shows 0.8–0.9 μg m^?3 for air masses from West and 2.1–2.2 μg m^?3 from East. The seasonal difference can be neglected.The half-hourly measurements of the particle mass concentration PM₁₀ evaluated as mean daily courses using a TEOM^® show low values (14–21 μg m^?3) in summer and winter for air masses transported from West and the highest concentrations (31–38 μg m^?3) in winter for air masses from East.The results demonstrate the influence of meteorological parameters on long-range transport, secondary particle mass formation and re-emission which modify mass concentration and composition of PM₁₀, PM_2.5 and PM₁. Melpitz site is located in the East of Germany faraway from strong local anthropogenic emissions (rural background). Therefore, this site is suitable for investigation of the influence of long-range transport of air pollution in continental air masses from the East with source regions inside and outside of the European Union.     

Chemical speciation of PM2.5 and PM10 in south Phoenix, AZ, USA

Phoenix, AZ, experiences high particulate matter (PM) episodes, especially in the wintertime. The spatial variation of the PM concentrations and resulting differences in exposure is of particular concern. In this study, PM2.s (PM with aerodynamic diameter <2.5 microm) and PM10 (PM with aerodynamic diameter <10 microm) samples were collected simultaneously from the east and west sides of South Phoenix and at a control site in Tempe and analyzed for trace elements and bulk elemental and organic carbon. Measurements showed that although PM2.5 concentrations had similar trends in temporal scale across all sites, concentrations of PM10 did not. The difference in PM10 concentrations and fluctuation across the three sites suggest effects of a local soil source as evidenced by high concentrations of Al, Ca, and Fe in PM10. K and anthropogenic elements (e.g., Cu, Pb, and Zn) in PM2.5 samples on January 1 were strikingly high, suggesting the influence of New Year's fireworks. Concentrations of toxic elements (e.g., Pb) in the study presented here are not different from similar studies in other U.S. cities. Application of principal component analysis indicated two broad categories of emission sources--soil and combustion--together accounting for 80 and 90% of variance, respectively, in PM2.5 and PM10. The soil and combustion components explained approximately 60 and 30% of the variance in PM10, respectively, whereas combustion sources dominated PM2.5 (>50% variance). Many elements associated with anthropogenic sources were highly enriched, with enrichment factors in PM2.5 an order of magnitude higher than in PM10 relative to surface soil composition in the study area.     

Wintertime PM2.5 and PM10 Source Apportionment at Sacramento,California

ABSTRACT

The chemical mass balance (CMB) model was applied to winter (November through January) 1991–1996 PM2.5 and PM10 data from the Sacramento 13th and T Streets site in order to identify the contributions from major source categories to peak 24-hr ambient PM_2.5 and PM₁₀ levels. The average monthly PM₁₀ monitoring data for the nine-year period in Sacramento County indicate that elevated concentrations are typical in the winter months. Concentrations on days of highest PM₁₀ are dominated by the PM2.5 fraction. One factor contributing to increased PM_2.5 concentrations in the winter is meteorology (cool temperatures, low wind speeds, low inversion layers, and more humid conditions) that favors the formation of secondary nitrate and sulfate aerosols. Residential wood burning also elevates fine particulate concentrations in the Sacramento area.

The results of the CMB analysis highlight three key points. First, the source apportionment results indicate that primary motor vehicle exhaust and wood smoke are significant sources of both PM_2.5 and PM₁₀ in winter. Second, nitrates, secondarily formed as a result of motor-vehicle and other sources of nitrogen oxide (NO_x), are another principal cause of the high PM_2.5 and PM₁₀ levels during the winter months. Third, fugitive dust, whether it is resuspended soil and dust or agricultural tillage, is not the major contributor to peak winter PM_2.5 and PM10 levels in the Sacramento area.     

重庆城区PM2.5化学组分特征及季节变化

2014年7月-2015年5月典型季节期间在重庆城区选择典型站点开展PM2.5样品采集,并测量质量浓度,分析样品中水溶性离子、无机元素、OC和EC等组分,在此基础上对组分化学组成进行了质量重构。结果表明：观测期间PM2.5年均值为76.4 μg·m-3,浓度季节变化为冬季 > 秋季 > 春季 > 夏季;组分方面,以二次转化为主的SO42-、NH4+、NO3-和OC是PM2.5组分中最主要成分,OC/EC比值4个季度均大于2,表明城区二次有机碳生成显著;硫氧化率（SOR）分析,气态污染物SO2的二次转化效率较高,大气存在明显的二次转化过程。PM2.5质量重构后主要组成为有机气溶胶（OM）、二次无机离子（SNA）和矿物尘,重庆城区应协同控制一次排放的颗粒物和气态污染物SO2和NOx,从而控制二次组分浓度。