Measuring Eddy Covariance Fluxes of Ammonia Using Tunable Diode Laser Absorption Spectroscopy

Field measurements of NH3 fluxes using an eddy covariance technique were made for a total of 60 days between July and September 2002 at an intensively managed grassland in Southern Scotland. The collected data demonstrate the suitability of a tuneable diode laser absorption spectroscopy (TDLAS) system coupled with a sonic anemometer for eddy covariance measurements. The novelty of these measurements is the application to ammonia, which has only become measurable using TDLAS techniques recently, because of its small ambient concentration. Data presented in this paper show typical features of the fluxes and concentration for the summer season. NH3 concentration and flux values are in a similar range to previous studies using flux gradient methods at the same field site, although the particularly wet season reduced the concentration of NH₃ in the air. For an example day, measured NH₃ fluxes ranged between –11 and 44 ng m^–2 s^–1 with an average value of 3.78 ng m^–2 s^–1 indicating a small net emission from the vegetation. Spectral analysis executed on the data shows the percentage of flux carried by the small eddies (from 0.2 to 2 m) suggesting that high detection frequency instruments are particularly suitable for estimating NH₃ fluxes between atmosphere and vegetation.     

Field scale N2O flux measurements from grassland using eddy covariance

In order to assess nitrous oxide (N₂O) emissions from typical intensively managed grassland in northern Britain fluxes were measured by eddy covariance using tuneable diode laser absorption spectroscopy from June 2002 to June 2003 for a total period of 4000 h. With micrometeorological techniques it is possible to obtain a very detailed picture of the fluxes of N₂O at field scale (10³–10⁴ m²), which are valuable for extrapolation to regional scales. In this paper three of the four fertilizer applications were investigated in detail. N₂O emissions did not always show a clear response. Hourly fluxes were very large immediately after the June 2002 nitrogen fertilizer application, peaking at 2.5 mg N₂O–N m^–2 s^–1. Daily fluxes were averaging about 300 ng N₂O m^–2 s^–1 over the 4 days following fertilizer application. The response of N₂O emissions was less evident after the August fertilization, although 2 days after fertilizer application an hourly maximum flux of 554 ng N₂O–N m^–2 s^–1 was registered. For the rest of August the flux was undetectable. The differences between fertilization events can be explained by different environmental conditions, such as soil temperature and rainfall. A fertiliser-induced N₂O emission was not observed after fertilizer application in March 2003, due to lack of rainfall. The total N₂O flux from June 2002 to June 2003 was 5.5 kg N₂O–N ha^–1y^–1, which is 2.8% of the total annual N fertilizer input.     

Spatial variability of soil gas concentration and methane oxidation capacity in landfill covers

In order to devise design criteria for biocovers intended to enhance the microbial oxidation of landfill methane it is critical to understand the factors influencing gas migration and methane oxidation in landfill cover soils. On an old municipal solid waste landfill in north-western Germany soil gas concentrations (10, 40, 90 cm depth), topsoil methane oxidation capacity and soil properties were surveyed at 40 locations along a 16 m grid. As soil properties determine gas flow patterns it was hypothesized that the variability in soil gas composition and the subsequent methanotrophic activity would correspond to the variability of soil properties. Methanotrophic activity was found to be subject to high spatial variability, with values ranging between 0.17 and 9.80 g CH₄ m⁻² h⁻¹_. Considering the current gas production rate of 0.03 g CH₄ m⁻² h⁻¹, the oxidation capacity at all sampled locations clearly exceeded the flux to the cover, and can be regarded as an effective instrument for mitigating methane fluxes. The methane concentration in the cover showed a high spatial heterogeneity with values between 0.01 and 0.32 vol.% (10 cm depth), 22.52 vol.% (40 cm), and 36.85 vol.% (90 cm). The exposure to methane raised the oxidation capacity, suggested by a statistical correlation to an increase in methane concentration at 90 cm depth. Methane oxidation capacity was further affected by the methanotroph bacteria pH optimum and nutrient availability, and increased with decreasing pH towards neutrality, and increased with soluble ion concentration). Soil methane and carbon dioxide concentration increased with lower flow resistance of the cover, as represented by the soil properties of a reduced bulk density, increase in air capacity and in relative ground level.     

Effect of industrial by-products containing electron acceptors on mitigating methane emission during rice cultivation

Three industrial by-products (fly ash, phosphogypsum and blast furnace slag), were evaluated for their potential re-use as soil amendments to reduce methane (CH₄) emission resulting from rice cultivation. In laboratory incubations, CH₄ production rates from anoxic soil slurries were significantly reduced at amendment levels of 0.5%, 1%, 2% and 5% (wt wt⁻¹), while observed CO₂ production rates were enhanced. The level of suppression in methane production was the highest for phosphogypsum, followed by blast slag and then fly ash. In the greenhouse experiment, CH₄ emission rates from the rice planted potted soils significantly decreased with the increasing levels (2–20 Mg ha⁻¹) of the selected amendments applied, while rice yield simultaneously increased compared to the control treatment. At 10 Mg ha⁻¹ application level of the amendments, total seasonal CH₄ emissions were reduced by 20%, 27% and 25%, while rice grain yields were increased by 17%, 15% and 23% over the control with fly ash, phosphogypsum, and blast slag amendments, respectively. The suppression of CH₄ production rates as well as total seasonal CH₄ flux could be due to the increased concentrations of active iron, free iron, manganese oxides, and sulfate in the amended soil, which acted as electron acceptors and controlled methanogens’ activity by limiting substrates availability. Among the amendments, blast furnace slag and fly ash contributed mainly to improve the soil nutrients balance and increased the soil pH level towards neutral point, but soil acidity was developed with phosphogypsum application. Conclusively, blast slag among the selected amendments would be a suitable soil amendment for reducing CH₄ emissions as well as sustaining rice productivity.     

Oxidation of SO2 in Clouds at Whiteface Mountain

In-cloud oxidation of SO₂ byH₂O₂ was investigated using a tracertechnique based on SO^2– ₄/Se ratios atWhiteface Mountain, New York during summer months from1990 to 1998. Cloud water samples collected at themountain's summit (1.5 km above mean sea level) andaerosols at a below cloud site (Lodge) located at 0.6km amsl and in cloud interstitial air at the summitwere analyzed for SO^2– ₄ and selectedtrace elements. Gaseous SO₂ andH₂O₂were measured in realtime. Cloud water pH wasgenerally below 5.0 with a mean value of 3.6. Theresults show that significant in cloud oxidation occursin clouds during summer months varying from belowdetection to 62% with on average approximately 24% ofthe cloud water SO^2– ₄ produced from in-situ SO₂ oxidation. During summer the clouds wereoxidant limited for approximately one third of thetime.     

Metabolic and Environmental Control on Methane Emission from Soils: Mechanistic Studies of Mesotrophic Fen in West Siberia

The biological mechanisms regulating methane emission fromnatural wetlands are the focus of this article. A novel techniqueprovides estimates of the distribution of CH₄ sources withinan undisturbed soil profile by recording the transient gasdynamics after soil enclosure by deep (50 cm) chamber. Thecombined use of conventional surface and soil chambers across a200-m fen transect allowed us to relate the observed methaneemission to its instant generation and uptake. Surprisingly, themethane generation was relatively constant (9–12 mg CH₄-C hr^-1 m^-2) and highly variable net emission (0.2–20 mg CH₄-C hr^-1 m^-2) was closely correlated (r = –0.809)with methane uptake. In laboratory incubations, CH₄ uptakefollowed Michaelis-Menten kinetics. Added chloride and nitrateirrespective of the cation's nature suppressed uptake as a strongnoncompetitive inhibitors (K _i 0.5 mM). The methaneformation turned out to be unstable and under anaerobicincubation, the formation of CH₄, CO₂ andH₂displayed sustained weekly oscillations. We conclude that effectsof environmental factors alone are not sufficient topredict the variation in emission, which depends also on metabolic control of respective soil organisms. The multitude ofsuch controls is dependent on diversity of respective soilorganisms and could be grouped into a limited number ofcategories considerably simplifying large-scale simulations.     

Assessment of the methane oxidation capacity of compacted soils intended for use as landfill cover materials

The microbial oxidation of methane in engineered cover soils is considered a potent option for the mitigation of emissions from old landfills or sites containing wastes of low methane generation rates. A laboratory column study was conducted in order to derive design criteria that enable construction of an effective methane oxidising cover from the range of soils that are available to the landfill operator. Therefore, the methane oxidation capacity of different soils was assessed under simulated landfill conditions. Five sandy potential landfill top cover materials with varying contents of silt and clay were investigated with respect to methane oxidation and corresponding soil gas composition over a period of four months. The soils were compacted to 95% of their specific proctor density, resulting in bulk densities of 1.4-1.7 g cm⁻³, reflecting considerably unfavourable conditions for methane oxidation due to reduced air-filled porosity. The soil water content was adjusted to field capacity, resulting in water contents ranging from 16.2 to 48.5 vol.%. The investigated inlet fluxes ranged from 25 to about 100 g CH₄ m⁻² d⁻¹, covering the methane load proposed to allow for complete oxidation in landfill covers under Western European climate conditions and hence being suggested as a criterion for release from aftercare. The vertical distribution of gas concentrations, methane flux balances as well as stable carbon isotope studies allowed for clear process identifications. Higher inlet fluxes led to a reduction of the aerated zone, an increase in the absolute methane oxidation rate and a decline of the relative proportion of oxidized methane. For each material, a specific maximum oxidation rate was determined, which varied between 20 and 95 g CH₄ m⁻² d⁻¹ and which was positively correlated to the air-filled porosity of the soil. Methane oxidation efficiencies and gas profile data imply a strong link between oxidation capacity and diffusive ingress of atmospheric air. For one material with elevated levels of fine particles and high organic matter content, methane production impeded the quantification of methane oxidation potentials. Regarding the design of landfill cover layers it was concluded that the magnitude of the expected methane load, the texture and expected compaction of the cover material are key variables that need to be known. Based on these, a column study can serve as an appropriate testing system to determine the methane oxidation capacity of a soil intended as landfill cover material.     

Uncontrolled methane emissions from a MSW landfill surface: Influence of landfill features and side slopes

Sanitary landfills for Municipal Solid Waste (MSW) disposal have been identified as one of the most important anthropogenic sources of methane (CH₄) emissions; in order to minimize its negative effects on the environment, landfill gas (LFG) recovery is a suitable tool to control CH₄ emissions from a landfill site; further, the measurement of CH₄ emissions can represent a good way to evaluate the effectiveness of LFG recovering systems. In general, LFG will escape through any faults in the landfill capping or in the LFG collection system. Indeed, some areas of the capping can be more permeable than others (e.g. portions of a side slope), especially when considering a temporarily capped zone (covered area that is not expected to receive any further waste for a period of at least 3 months, but for engineering reasons does not have a permanent cap yet). These areas, which are characterized by abnormal emissions, are usually defined as “features”: in particular, a feature is a small, discrete area or an installation where CH₄ emissions significantly differ from the surrounding zones. In the present study, the influence that specific features have on CH₄ emissions has been investigated, based on direct measurements carried out in different seasons by means of a flux chamber to the case study of Palermo (IT) landfill (Bellolampo). The results showed that the flux chamber method is reliable and easy to perform, and the contoured flux maps, obtained by processing the measured data were found to be a suitable tool for identifying areas with abnormal (high) emissions. Further, it was found that a relationship between methane emission rates and landfill side slope can be established. Concerning the influence of the temporary HDPE cover system on CH₄ recovery efficiency, it contributed to a significant decrease of the free surface area available for uncontrolled emissions; this aspect, coupled to the increase of the CH₄ volumes collected by the LFG recovery system, led to a significant increase of the recovery efficiency.     

Tracer method to measure landfill gas emissions from leachate collection systems

This paper describes a method developed for quantification of gas emissions from the leachate collection system at landfills and present emission data measured at two Danish landfills with no landfill gas collection systems in place: Fakse landfill and AV Miljø. Landfill top covers are often designed to prevent infiltration of water and thus are made from low permeable materials. At such sites a large part of the gas will often emit through other pathways such as the leachate collection system. These point releases of gaseous constituents from these locations cannot be measured using traditional flux chambers, which are often used to measure gas emissions from landfills. Comparing tracer measurements of methane (CH₄) emissions from leachate systems at Fakse landfill and AV Miljø to measurements of total CH₄ emissions, it was found that approximately 47% (351 kg CH₄ d^?1) and 27% (211 kg CH₄ d^?1), respectively, of the CH₄ emitting from the sites occurred from the leachate collection systems. Emission rates observed from individual leachate collection wells at the two landfills ranged from 0.1 to 76 kg CH₄ d^?1. A strong influence on emission rates caused by rise and fall in atmospheric pressure was observed when continuously measuring emission from a leachate well over a week. Emission of CH₄ was one to two orders of magnitude higher during periods of decreasing pressure compared to periods of increasing pressure.     

The Effects of Three Thermo Electric Power Plants on Yerkesik-Denizova Forests in Mugla Province (Turkey)

Mugla is a city that is located in the southwest part of Turkey. Three thermo-electric power plants called Yatagan (3 × 210 MW) and Yenikoy (2 × 210 MW)and Kemerkoy (Gokova, 3 × 210 MW) havebeen constructed in this region and also have begun operation in 1982 – 1983 – 1984 (three units), in 1988 and in 1995, respectively. The Pinus brutia forests in Yerkesik–Denizova region have been under the common effects of Yenikoy and Yatagan thermo-electric power plants. Therefore, these Pinus brutia forests have startedto dry in groups since 1988. In addition, Kemerkoy thermo-electric power plant, began operation in 1995.Polluting gases arrived in Denizova-Yerkesik throughKoca Stream Valley Forests.Increasing quantities of polluting gases and especially SO₂ have dried the trees in large amounts in this 1650 ha forestland area. YataganThermo-electric power plant has caused drying of Pinus brutia in Bencik Mountain, which was on the south in 1984–1985. The same phenomenon was seen in Denizova-Yerkesik Forest in 1999–2000. It was observed that sulphur content was varying between 4218–6676 ppm at the Pinus brutia needle samples taken in this region on 16 December 2000. Sulphur contents were correlated with the age of needle (1–2 yr old), density of yellow stains on the needles and amount of drying needles. Particularly in 1996–2000 period, the destruction of chlorophyll in needles due to the impacts of SO₂ was also correlated with narrowing of the annual rings from one year to another. The narrowing ratio of yearly rings reached 60–504% for 94–95 yr old, and 375–661% for 58–63 yr old Pinus brutia trees during the 1986–1990, 1991–1995 and 1996–2000 periods.All these results clearly showed that the decrease in the chlorophyll content in needles under the effect of air pollution caused important reduction in the raw timber production and its inputs to the economy. In other words, drying due to increased ecological sensitivity or direct hazard of pollutants emitted by the power plants and cutting of trees have been notably increased in the region. This has created serious economic losses.     

Design of top covers supporting aerobic in situ stabilization of old landfills – An experimental simulation in lysimeters

Landfill aeration by means of low pressure air injection is a promising tool to reduce long term emissions from organic waste fractions through accelerated biological stabilization. Top covers that enhance methane oxidation could provide a simple and economic way to mitigate residual greenhouse gas emissions from in situ aerated landfills, and may replace off-gas extraction and treatment, particularly at smaller and older sites. In this respect the installation of a landfill cover system adjusted to the forced-aerated landfill body is of great significance. Investigations into large scale lysimeters (2 × 2 × 3 m) under field conditions have been carried out using different top covers including compost materials and natural soils as a surrogate to gas extraction during active low pressure aeration. In the present study, the emission behaviour as well as the water balance performance of the lysimeters has been investigated, both prior to and during the first months of in situ aeration. Results reveal that mature sewage sludge compost (SSC) placed in one lysimeter exhibits in principle optimal ambient conditions for methanotrophic bacteria to enhance methane oxidation. Under laboratory conditions the mature compost mitigated CH₄ loadings up to 300 l CH₄/m² d. In addition, the compost material provided high air permeability even at 100% water holding capacity (WHC). In contrast, the more cohesive, mineral soil cover was expected to cause a notably uniform distribution of the injected air within the waste layer. Laboratory results also revealed sufficient air permeability of the soil materials (TS-F and SS-Z) placed in lysimeter C. However, at higher compaction density SS-Z became impermeable at 100% WHC.Methane emissions from the reference lysimeter with the smaller substrate cover (12–52 g CH₄/m² d) were significantly higher than fluxes from the other lysimeters (0–19 g CH₄/m² d) during in situ aeration. Regarding water balance, lysimeters covered with compost and compost-sand mixture, showed the lowest leachate rate (18–26% of the precipitation) due to the high water holding capacity and more favourable plant growth conditions compared to the lysimeters with mineral, more cohesive, soil covers (27–45% of the precipitation).On the basis of these results, the authors suggest a layered top cover system using both compost material as well as mineral soil in order to support active low-pressure aeration. Conventional soil materials with lower permeability may be used on top of the landfill body for a more uniform aeration of the waste due to an increased resistance to vertical gas flow. A compost cover may be built on top of the soil cover underlain by a gas distribution layer to improve methane oxidation rates and minimise water infiltration. By planting vegetation with a high transpiration rate, the leachate amount emanating from the landfill could be further minimised. The suggested design may be particularly suitable in combination with intermittent in situ aeration, in the later stage of an aeration measure, or at very small sites and shallow deposits. The top cover system could further regulate water infiltration into the landfill and mitigate residual CH₄ emissions, even beyond the time of active aeration.     

Methane emissions from MBT landfills

Within the scope of an investigation for the German Federal Environment Agency (“Umweltbundesamt”), the basics for the estimation of the methane emissions from the landfilling of mechanically and biologically treated waste (MBT) were developed. For this purpose, topical research including monitoring results regarding the gas balance at MBT landfills was evaluated.For waste treated to the required German standards, a methane formation potential of approximately 18–24 m³ CH₄/t of total dry solids may be expected. Monitoring results from MBT landfills show that a three-phase model with differentiated half-lives describes the degradation kinetics in the best way. This is due to the fact that during the first years of disposal, the anaerobic degradation processes still proceed relatively intensively. In addition in the long term (decades), a residual gas production at a low level is still to be expected.Most of the soils used in recultivation layer systems at German landfills show a relatively high methane oxidation capacity up to 5 l CH₄/(m² h). However, measurements at MBT disposal sites indicate that the majority of the landfill gas (in particular at non-covered areas), leaves the landfill body via preferred gas emission zones (hot spots) without significant methane oxidation. Therefore, rather low methane oxidation factors are recommended for open and temporarily covered MBT landfills. Higher methane oxidation rates can be achieved when the soil/recultivation layer is adequately designed and operated.Based on the elaborated default values, the First Order Decay (FOD) model of the IPCC Guidelines for National Greenhouse Gas Inventories, 2006, was used to estimate the methane emissions from MBT landfills. Due to the calculation made by the authors emissions in the range of 60,000–135,000 t CO_2-eq./a for all German MBT landfills can be expected. This wide range shows the uncertainties when the here used procedure and the limited available data are applied. It is therefore necessary to generate more data in the future in order to calculate more precise methane emission rates from MBT landfills. This is important for the overall calculation of the climate gas production in Germany which is required once a year by the German Government.     

A Geochemical Multi-Methodological Approach in Hazard Assessment of CO2-Rich Gas Emissions at Mt. Amiata Volcano (Tuscany, Central Italy)

The present work aims to assess the hazard for human health related to CO₂ anomalous concentrations in air emitted from dry gas vents located in the NE area of Mt. Amiata volcano (Tuscany, central Italy). A geochemical multi-methodological approach is adopted to determine the composition and the flux rate of the gas discharges in order to establish (1) the origin of the gas vents and (2) the behaviour of the discharged gases in the areas surrounding the emission sites. The gas vents are hosted within sub-circular morphological depressions (??～?10–30 m), which likely originated by the collapse of cavities formed at shallow depth in the ground by dissolution of Triassic anhydrite formations and recent travertine deposits. CaCO₃ and CaSO₄ dissolution is mainly related to the underground circulation of CO₂-rich fluids whose hydrological pattern is regulated by local and regional tectonics. The CO₂-rich (up to 996,070 μmol/mol) gases tend to accumulate within the topographic lows, thus creating a sort of CO₂ ponds, and the knowledge of their evolution in time and space is important to evaluate the related hazard. Consequently, a conceptual model of CO₂ diffusion in air is developed to understand the dynamic of the CO₂ accumulation/dispersion process based on (1) a 24-h continuous measurement of the CO₂ flux from one of the main emission sites and (2) the recording of the main meteoric parameters, i.e. air temperature, wind direction and speed to check their influence. The results indicate that the threshold of CO₂ concentrations considered dangerous for the human health is frequently overcome. Moreover, when meteoric conditions, i.e. low wind and cloudy weather, did not allow a rapid dispersion of the gas phase emitted from the dry vents, CO₂-rich clouds periodically overflowed the morphological depressions for several tens of meters without any significant mixing with air. On the basis of these considerations, the monitoring of the output rate from the main gas emissions, combined with the continuous control of the local meteorological parameters, may be considered an efficient procedure to mitigate the CO₂ hazard deriving from dry gas vents. An improvement of the protocol can be achieved in case of installations of CO₂ sensors located in the most sensitive areas and connected to a telemetry system able to transmit the data in real time to the closest Civil Defence centre. The CO₂ degassing sites can also represent a tourist attraction after the installation of suitable metallic fences and a proper campaign of information about these natural phenomena.     

Mitigation of methane emission from Fakse landfill using a biowindow system

Landfills are significant sources of atmospheric methane (CH₄) that contributes to climate change, and therefore there is a need to reduce CH₄ emissions from landfills. A promising cost efficient technology is to integrate compost into landfill covers (so-called “biocovers”) to enhance biological oxidation of CH₄. A full scale biocover system to reduce CH₄ emissions was installed at Fakse landfill, Denmark using composted yard waste as active material supporting CH₄ oxidation. Ten biowindows with a total area of 5000 m² were integrated into the existing cover at the 12 ha site. To increase CH₄ load to the biowindows, leachate wells were capped, and clay was added to slopes at the site. Point measurements using flux chambers suggested in most cases that almost all CH₄ was oxidized, but more detailed studies on emissions from the site after installation of the biocover as well as measurements of total CH₄ emissions showed that a significant portion of the emission quantified in the baseline study continued unabated from the site. Total emission measurements suggested a reduction in CH₄ emission of approximately 28% at the end of the one year monitoring period. This was supported by analysis of stable carbon isotopes which showed an increase in oxidation efficiency from 16% to 41%. The project documented that integrating approaches such a whole landfill emission measurements using tracer techniques or stable carbon isotope measurements of ambient air samples are needed to document CH₄ mitigation efficiencies of biocover systems. The study also revealed that there still exist several challenges to better optimize the functionality. The most important challenges are to control gas flow and evenly distribute the gas into the biocovers.     

Evaluation of methane emissions from Palermo municipal landfill: Comparison between field measurements and models

Methane (CH₄) diffuse emissions from Municipal Solid Waste (MSW) landfills represent one of the most important anthropogenic sources of greenhouse gas. CH₄ is produced by anaerobic biodegradation of organic matter in landfilled MSW and constitutes a major component of landfill gas (LFG). Gas recovery is a suitable method to effectively control CH₄ emissions from landfill sites and the quantification of CH₄ emissions represents a good tool to evaluate the effectiveness of a gas recovery system in reducing LFG emissions. In particular, LFG emissions can indirectly be evaluated from mass balance equations between LFG production, recovery and oxidation in the landfill, as well as by a direct approach based on LFG emission measurements from the landfill surface. However, up to now few direct measurements of landfill CH₄ diffuse emissions have been reported in the technical literature. In the present study, both modeling and direct emission measuring methodologies have been applied to the case study of Bellolampo landfill located in Palermo, Italy. The main aim of the present study was to evaluate CH₄ diffuse emissions, based on direct measurements carried out with the flux accumulation chamber (static, non-stationary) method, as well as to obtain the CH₄ contoured flux map of the landfill. Such emissions were compared with the estimate achieved by means of CH₄ mass balance equations. The results showed that the emissions obtained by applying the flux chamber method are in good agreement with the ones derived by the application of the mass balance equation, and that the evaluated contoured flux maps represent a reliable tool to locate areas with abnormal emissions in order to optimize the gas recovery system efficiency.     

The spatial distribution of ammonia emitted from seabirds and its contribution to atmospheric nitrogen deposition in the UK

Simple bioenergetics models were used to derive annual nitrogen excretion rates of each seabird species occurring at colonies in the UK. These were combined with population distribution data and an estimated fraction of nitrogen volatilized to estimate the spatial distribution of NH₃ emissions from seabird colonies at a 1 km resolution. The effect of these emissions on atmospheric NH₃ concentrations and nitrogen deposition in the UK was assessed using the FRAME atmospheric chemistry and transport model. The total emission of NH₃ from the UK seabird colonies is estimated at 2.7 kt yr^–1. Emissions from seabirds are largely concentrated in remote parts of Britain, where agricultural and other anthropogenic emissions are minimal. Although seabirds account for less than 1% of total UK NH₃ emissions (370 kt yr^–1), their occurrence in remote areas and frequently large colony sizes results in seabirds providing a major fraction of the atmospheric nitrogen deposition for many remote ecosystems.     

Comparison of the Chemical Composition of Mineral Particles Collected in Dunhuang,China and those Collected in the Free Troposphere over Japan: Possible Chemical Modification during Long-Range Transport

The Asian continent is recognized as one of the most important sources of mineral (or soil) particles. These particles have a large potential to effect global changes through the biogeochemical cycle of particulates and through radiative balance (IPCC Third Assessment Report, 2001). Therefore, comparison of particle compositions near the source region and those after long-range transport is important in understanding the long-range particle transport phenomenon. Individual aerosolparticles were collected in Dunhuang (40°09N; 94°41E), China. Particles were collected at the campus of the Meteorological Bureau of Dunhuang City (17 August 2001) and near the Mogao Grots, located approximately 30 km from Dunhuang (18 August 2001, 18 October 2001 and 13 January 2002) using a two-stage low-volume impactor. The morphology of individual aerosol particles and their elemental compositions were examined via a scanning electron microscope (Hitachi, S-3000N) equipped with an energy dispersive X-ray (EDX) analyzer (Horiba, EMAX-500). The particles collected at these locations were comprised primarily of minerals, with the exception of sulphateparticles in the submicron range that were contained in thesample collected on 18 October 2001 (likely, ammonium sulphate). The most abundant elements were found to be Si and Al. Approximately 46–77% of the collected particles were Si-richparticles (composed primarily of quartz and aluminosilicate),and 13–41% of the collected particles were Ca-rich particles,such as calcite (CaCO₃), dolomite (CaMg(CO₃)₂),and gypsum (CaSO₄2H₂O). The fractions of Fe-rich, Mg-rich, Ti-rich, K-rich, and Cl-rich were 3–10, 0–7, 0–3, 0–1, and 0–1%, respectively. Similar types of mineral particles were found in the free troposphere over Japan(Trochkine et al., 2002). A number of differences were found to exist between the particles collected in China and thosecollected in Japan, and these differences can be explained bychemical modification of the particles during transport fromChina to Japan.     

Carbon Sequestration: Do N Inputs and Elevated Atmospheric CO2 Alter Soil Solution Chemistry and Respiratory C Losses?

Soil respiration is a large C flux which is of primary importance in determining C sequestration. Here we ask how it is altered by atmospheric CO₂ concentration and N additions. Swards of Lolium perenne L. were grown in a Eutric cambisol under controlled conditions with and without the addition of 200 kg NO ₃ ^– –N ha^–1, at either 350 ppm or 700 ppm CO₂, for 3 months. Soil respiration and net canopy photosynthesis were both increased by added N and elevated CO₂, but soil respiration increased proportionately less than fixation by photosynthesis. Thus, both elevated CO₂ and N appeared to increase potential C sequestration, although adding N at elevated CO₂ reduced the C sequestered as a proportion of that fixed relative to elevated CO₂ alone. Across all treatments below-ground respiratory C losses were predicted by root biomass, but not by soil solution C and N concentrations. Specific root-dependent respiration was increased by elevated CO₂, such that belowg-round respiration per unit biomass and per unit plant N was increased.     

Methane oxidation at a surface-sealed boreal landfill

Methane oxidation was studied at a closed boreal landfill (area 3.9 ha, amount of deposited waste 200,000 tonnes) equipped with a passive gas collection and distribution system and a methane oxidative top soil cover integrated in a European Union landfill directive-compliant, multilayer final cover. Gas wells and distribution pipes with valves were installed to direct landfill gas through the water impermeable layer into the top soil cover. Mean methane emissions at the 25 measuring points at four measurement times (October 2005–June 2006) were 0.86–6.2 m³ ha^?1 h^?1. Conservative estimates indicated that at least 25% of the methane flux entering the soil cover at the measuring points was oxidized in October and February, and at least 46% in June. At each measurement time, 1–3 points showed significantly higher methane fluxes into the soil cover (20–135 m³ ha^?1 h^?1) and methane emissions (6–135 m³ ha^?1 h^?1) compared to the other points (<20 m³ ha^?1 h^?1 and <10 m³ ha^?1 h^?1, respectively). These points of methane overload had a high impact on the mean methane oxidation at the measuring points, resulting in zero mean oxidation at one measurement time (November). However, it was found that by adjusting the valves in the gas distribution pipes the occurrence of methane overload can be to some extent moderated which may increase methane oxidation. Overall, the investigated landfill gas treatment concept may be a feasible option for reducing methane emissions at landfills where a water impermeable cover system is used.     

CH4/CO2 ratios indicate highly efficient methane oxidation by a pumice landfill cover-soil

Landfills that generate too little biogas for economic energy recovery can potentially offset methane (CH₄) emissions through biological oxidation by methanotrophic bacteria in cover soils. This study reports on the CH₄ oxidation efficiency of a 10-year old landfill cap comprising a volcanic pumice soil. Surface CH₄ and CO₂ fluxes were measured using field chambers during three sampling intervals over winter and summer. Methane fluxes were temporally and spatially variable (?0.36 to 3044 mg CH₄ m^?2 h^?1); but were at least 15 times lower than typical literature CH₄ fluxes reported for older landfills in 45 of the 46 chambers tested. Exposure of soil from this landfill cover to variable CH₄ fluxes in laboratory microcosms revealed a very strong correlation between CH₄ oxidation efficiency and CH₄/CO₂ ratios, confirming the utility of this relationship for approximating CH₄ oxidation efficiency. CH₄/CO₂ ratios were applied to gas concentrations from the surface flux chambers and indicated a mean CH₄ oxidation efficiency of 72%. To examine CH₄ oxidation with soil depth, we collected 10 soil depth profiles at random locations across the landfill. Seven profiles exhibited CH₄ removal rates of 70–100% at depths <60 cm, supporting the high oxidation rates observed in the chambers. Based on a conservative 70% CH₄ oxidation efficiency occurring at the site, this cover soil is clearly offsetting far greater CH₄ quantities than the 10% default value currently adopted by the IPCC.