Evaluation of the Ceilcote ionizing wet scrubber

The Ceilcote ionizing wet scrubber installed on a refractory brick kiln was evaluated with tests involving particulate mass emission, particle size distribution, and opacity. The overall efficiency was 93% with an average outlet opacity of 8% on a 1.68 m (5.5 ft) path length. The average particle cut diameter of the scrubber is 0.5 microns with a theoretical power input of 67 W/am³ (2.5 hp/1000 acfm). The theoretical power requirement for the ionizing wet scrubber was 41 W/am³ (1.54 hp/1000 acfm). A cooling tower supplying chilled water to the prescrubber required an additional 26 W/am² (0.96 hp/1000 acfm) for a total system input of 67 W/am³ (2.5 hp/1000 acfm). It is recommended that the scrubber be considered where practical for the removal of fine particulate matter.     

Design guidelines for an optimum scrubber system

The revised New Source Performance Standards (NSPS) for the utility industry mandates reduced particulate matter and sulfur dioxide emissions from new utility boilers. A wet scrubber system can be an advantage in controlling both of these emissions. Existing wet scrubber systems may meet the new standards with significant increase in power consumption. A careful design of the entire scrubber system, based on the experience gained at the existing installations, is necessary to ensure cost effectiveness. The experience with existing wet scrubber systems used on coal-fired utility boilers is reviewed and their performance is correlated with power consumptions. Based on a correlation of scrubber pressure drop against outlet concentration, conventional scrubber systems would be able to meet the revised NSPS for particulate matter with a theoretical scrubber pressure drop of 43±5 cm H₂O. Overall system pressure drop, however, could easily run as high as 76 cm H₂O. Novel scrubber systems such as the electrostatically augmented scrubber may provide the necessary collection performance at lower pressure drops. The performance of the various scrubber components such as mist eliminators and reheaters is reviewed. Operating problems are also discussed.     

Chironomid larval deformity frequencies, mortality, and diversity in heavy-metal contaminated sediments of a Canadian riverine wetland

Sediment sampling at point source locations in the Niagara River watershed revealed an area in a Class One Provincially Significant Riverine Wetland that was located near the discharge of a stainless steel company. The site had unusually high concentrations of heavy metals and oily wastes in its sediments. The impacts of these oil and heavy metal contaminated sediments on an invertebrate population of midge (chironomid) larvae was assessed using both lab and field techniques. The midge larvae were the dominant invertebrates in this section of the river. Twenty-six percent of the chironomids from sites located 10 to 800 m downstream of the stainless steel company's point source were deformed. A lab study was carried out to determine what percentage of the observed deformities could be attributed to the heavy metal content of the sediments and what percentage was due to the organic fraction. Sediments collected near the point source were tested and found to be acutely toxic. Sediments collected 60 m downstream of the point source were teratogenic. The frequency of mentum deformities for chironomids reared in clean sediments (control aquaria) was only 2.2%. A similar deformity frequency (2.2%) was observed at the clean sediment reference site in the Welland River watershed. Of the 97 chironomids removed from the de-oiled heavy metal contaminated sediments in the test aquarium, 10.3% displayed deformities. This is believed to be one of the few times that chironomid deformities were induced in a controlled lab study in which heavy metal concentrations similar to those found in the field were used.     

Comparison of the chromotropic acid and modified pararosaniline methods for the determination of formaldehyde in air

Follow-up tests were performed in 25 complaint homes previously investigated by the Wisconsin Division of Health to determine ambient formaldehyde concentrations. Four collection methods were compared in each home: (1) midget impingers containing double-distilled water and immersed in ice baths, (2) midget impingers containing 1% sodium bisulfite solution and immersed in ice baths, (3) midget impingers containing cold 1% sodium bisulfite solution (temperature not maintained with an ice bath), and (4) a refrigerated, complete sampling unit developed at Lawrence Berkley Laboratory which utilized double-distilled water as a collection medium. Air was drawn through the midget impingers using personal sampling pumps. All four types of sampling trains were operated simultaneously in a bedroom, collecting specimens within an area of about 4 ft², while in the kitchen or living room, all sampling trains except for the impingers containing 1% sodium bisulfite solution and immersed in ice baths were operated together. Analysis of variance indicated that the three samples collected using midget impingers and personal sampling pumps gave similar results. All specimens collected in water were analyzed using both the chromotropic acid and pararosaniline analytical methods. Quality control specimens prepared in the laboratory showed excellent agreement between the two methods; however, field specimens through which air had been drawn were assigned lower values using the pararosaniline method. Special precautions were taken to ensure that specimens collected in water were not contaminated with sodium bisulfite, a serious interference for the pararosaniline test. To rule out the possibility that specimens deteriorated between analysis, test results from each method were confirmed by repeating each method for selected sets of specimens for a period of several days. It was hypothesized that some source of interference was present in the field specimens which affected the pararosaniline analysis. Statistical tests were applied to determine whether the observed discrepancy between the analytical methods was consistent and a regression model was employed to determine whether any of the other environmental parameters measured during sample collection was associated with the discrepancy.     

Application of slipstreamed air pollution control devices on waste-as-fuel processes

The recovery of energy from the combustion of municipal solid wastes is becoming an attractive alternative as landfill space becomes scarce and the availability of fossil fuels decreases. Particulate emissions from “waste-as-fuel” processes, however, may differ significantly in chemical and physical properties from particulate emissions produced by firing only coal. Such differences can affect the design and operation of air pollution control equipment. Presented in this paper are the results of a 2-month test program at Ames, Iowa, with a mobile electrostatic precipitator (ESP) and a mobile scrubber supplied by the U.S. Environmental Protection Agency (EPA), Industrial Environmental Research Laboratory (IERL), Research Triangle Park. PEDCo Environmental, Inc., and Acurex Corporation jointly conducted the test program to examine the effect of burning refuse-derived fuel (RDF) on particulate and heavy metal control efficiencies. The mobile ESP was used only as a primary control device, whereas the mobile scrubber was tested both upstream and downstream of the existing full-scale ESP. This paper also presents a status report on a PEDCo test program with a pilot fabric filter at Ames.     

Laboratory studies of the diffusive transport of Cs and Co through potential waste repository soils

Tests using reconstituted samples have been performed to assess the diffusive transport of ¹³⁷Cs and ⁶⁰Co through natural regolith materials from a region in South Australia being considered for a radioactive waste repository. A double diffusion cell apparatus made of polycarbonate resin was developed to estimate the effective diffusion (D_e) and sorption coefficients (K_d) that allowed large withdrawals from the source and collector cells and has enabled tests with low concentrations of radioactivity. An alternative to porous stainless steel filter plates has also been used to reduce uncertainty in test interpretation. Analysis of the transient data used a staged method of the Laplace transform to take into consideration the volume of the samples withdrawn from the apparatus during testing. At test completion samples were cut into slices and analysed for radionuclide concentration. Data obtained from the sliced samples confirmed that both numerical and experimental data produced acceptable mass balance. The D_e values obtained in this study were of the order of 10⁻⁶ cm² s⁻¹ for both species, higher than previously published data. The K_d values from the diffusion and batch sorption tests were in reasonable agreement for ¹³⁷Cs, but an order of magnitude different for ⁶⁰Co. The sorption of the latter radionuclide was strongly pH dependent, and this dependency during diffusion tests would benefit from further investigation.     

Characterising the performance of a tapered scrubber for controlling particulate emission

The performance of a modified tapered scrubber using water is presented in this article. The column is fabricated with internals so as to improve the performance of a simple tapered bubble scrubber. Experimentation indicates that the system developed can obtain almost 100% particulate (fly ash) removal efficiency under certain hydrodynamical conditions and the removal efficiency has been found to be higher than the existing similar systems. An empirical correlation is put forward for the prediction of removal efficiency as a function of relevant variables of the system. Experimental results agree very well with the correlation.     

Analysis of the toxic effects of physical and chemical properties of hypolimnetic waters by time series

A field experiment was conducted to identify potential causes of an existing fish kill problem and to identify useful control variables to assist in minimizing future fish kills. The experiment is described along with the mechanism deduced from earlier histological specimens and observed chemical phenomena. Time series analysis of chemical and biological variables is used to elucidate various hypothesis of the postulated fish kill mechanism.     

Sequential extraction of 226Ra in sediments from an estuary affected historically by anthropogenic inputs of natural radionuclides

Riverbed sediments from an estuary historically affected by wastes discharged by several phosphate fertiliser plants and enriched in uranium-series radionuclides were operationally speciated using a Tessier-based method. In each selective fraction the (226)Ra content was determined by alpha-particle spectrometry after radiochemical isolation and electrodeposition onto stainless steel planchets. These studies were performed in (226)Ra-polluted estuarine sediments collected one year after anthropogenic discharges had ceased in order to obtain useful information about the operational forms in which this radionuclide remains associated with the sediments at this time. The results obtained revealed that one year after (226)Ra inputs had stopped, the radionuclide was associated mostly with the more refractory forms. Consequently, it is possible to foresee little potential remobilisation of (226)Ra contamination from sediments to the aqueous phase in the future under normal environmental conditions.     

An experimental study on shrinkage of earth plaster with natural fibres for straw bale buildings

In this paper, a series of laboratory tests on shrinkage of plaster materials are presented. The plaster materials consist of cohesive soil, sand and different natural fibres. Three types of fibres, wheat straw, barley straw and wood shavings, were used as reinforcement in the tests. The shrinkage behaviour of earth plasters was studied by laboratory tests for different compositions and under different curing conditions. The specimens of plaster material were dried under a constant temperature of 30, 50 and 70°C, respectively. The effect of the following factors on shrinkage was investigated: temperature, soil composition, fibre type and fibre content. It was established that shrinkage crack formation decreases with increasing fibre content and increases with increasing soil content. In general, it was also found that lower curing temperature and higher fibre content are to be preferred to improve the performance of earth plasters.     

Modelling spatial variability using soil profiles in the Riverland of South Australia.

The soils of the Riverland vary significantly throughout the region. Soils from a vineyard near Loxton, whilst having only half the topsoil depth of two near Waikerie, are comparable in water-holding capacity because the soils are less sandy. Topographic difference can cause an additional variation between areas in the same neighbourhood. Highland soils typically develop a dune swale topography that gives rise to anisotropic semivariograms. First slope soils on the other hand give isotropic semivariograms. Semivariograms for topsoil depth and readily available water (RAW) for the three vineyards are used in the calculation of the efficiency of the sampling grids employed to gain an understanding of the soils. Kriging variance values have been calculated for 1, 2, 3 and 4 hectare square irrigation valve areas (IVAs) using the industry standard grid 75 x 75 m as well as grids 50 x 50 m and 100 x 100 m. Choice of the appropriate sampling grid to achieve a specified accuracy can thus be made.     

Geographical variation in relative risks associated with heat: Update of Spain's Heat Wave Prevention Plan

A decade after the implementation of prevention plans designed to minimise the impact of high temperatures on health, some countries have decided to update these plans in order to improve the weakness detected in these ten years of operation.In the case of Spain, this update has fundamentally consisted of changing the so-called “threshold” or “trigger” temperatures used to activate the plan, by switching from temperature values based on climatological criteria to others obtained by epidemiological studies conducted on a provincial scale.This study reports the results of these “trigger” temperatures for each of Spain's 52 provincial capitals, as well as the impact of heat on mortality by reference to the relative risks (RRs) and attributable risks (ARs) calculated for natural as well as circulatory and respiratory causes.The results obtained for threshold temperatures and RRs show a more uniform behaviour pattern than those obtained using temperature values based on climatological criteria; plus a clear decrease in RRs of heat-associated mortality due to the three causes considered, at both a provincial and regional level as well as for Spain as a whole.The updating of prevention plans is regarded as crucial for optimising the operation of these plans in terms of reducing the effect of high temperatures on population health.     

Assessment of the genotoxicity of 137Cs radiation using Vicia-micronucleus, Tradescantia-micronucleus and Tradescantia-stamen-hair mutation bioassays

Since the middle of the 20th century, ionizing radiations from radioactive isotopes including 137Cs have been investigated to determine their genotoxic impact on living organisms. The present study was designed to compare the effectiveness of three plant bioassays to assess DNA damage induced by low doses of 137Cs: Vicia-micronucleus test (Vicia-MCN), Tradescantia-micronucleus test (Trad-MCN) and Tradescantia-stamen-hair mutation test (Trad-SH) were used. Vicia faba (broad bean) and Tradescantia clone 4430 (spiderwort) were exposed to 137Cs according to different scenarios: external and internal (contamination) irradiations. Experiments were conducted with various levels of radioactivity in solution or in soil, using solid or liquid 137Cs sources. The three bioassays showed different sensitivities to the treatments. Trad-MCN appeared to be the most sensitive test (significative response from 1.5 kBq/200 ml after 30 h of contamination). Moreover, at comparable doses, internal irradiations led to larger effects for the three bioassays. These bioassays are effective tests for assessing the genotoxic effects of radioactive 137Cs pollution.     

Control of salt laden particulate emissions from hogged fuel boilers

This paper presents the results of an evaluation of excessive salt emissions from 16 hogged fuel boilers in Washington, Oregon, and Alaska. Logs transported or stored in sea water, absorb substantial amounts of salt which is noncombustible, and is emitted as a fine particulate when the hogged fuel is burned, contributing to opacity and particulate emissions. Control measures considered are fuel pretreatment, combustion modification, use of conventional particulate control devices (electrostatic precipitators, fabric filters, and wet scrubbers), and several novel particulate control devices.The best available control technology appears to be a mechanical collector-fabric filter combination; some electrostatic scrubber type devices have also shown excellent capability.     

The use of plant seeds in toxicity tests of phenolic compounds

Three types of plant seeds-millet, radish, and velvetleaf-were used for toxicity tests of phenolic compounds. Preliminary tests using deionized water indicated that the seed assay was simple, and the toxicity tests of various phenolic compounds showed that results were reproducible. Among the three types of seeds, millet was most sensitive in most cases. The drawback for seed toxicity tests is that plant seeds appear to be less sensitive than other bioassay organisms; however, their simplicity and accuracy should not be overlooked.     

Analysis of priority pollutants at a primary aluminum production facility

This paper investigated the source of priority pollutants, assessment of the wastewater treatment plant, and priority pollutant removal efficiency for a single Soderberg-type primary aluminum plant.Forty-eight hour composite samples were collected from the following streams: (1) plant intake water; (2) wastewater from the primary air pollution control system (gas stream cooling water and wet ESPs); (3) secondary air pollution control system (room ventilation wet scrubber liquor); (4) paste plant briquette cooling water; and (5) final effluent after the wastewater treatment plant.Wastewater from the primary air pollution control system entered a conventional chemical coagulation (using slacked lime) — clarification plant. Clarified water from the clarifier was combined with the other three wastewater streams and flowed into a settling lagoon with a 20-h hydraulic retention time. Clarified lagoon water was finally discharged to the river.The principal source of organic compounds in the wastewater was from the primary and secondary air pollution control systems and results from the volatilization of petroleum coke and pitch in the Soderberg anode. Wastewater treatment plant removal efficiencies of greater than 85% were achieved for the majority of the organic priority pollutant species detected.     

Life cycle assessment environmental data for structural steel construction in Greece

The construction industry is a critical sector in relation to sustainable development as its optimisation in terms of the consumption of resources can provide significant environmental benefits. To achieve this, a number of tools and methodologies have been developed to assist decision making. Life cycle assessment is one of the most acknowledged and widely used methodologies to assess the sustainability of construction works. Its efficient use, however, requires environmental data that in some cases are not yet available. Especially for sectors such as steel construction in which the potential for sustainable development is increased due to the recycling and reuse potential of the material, the lack of such data slows sustainability-related progress down. The current research addresses this issue by collecting primary environmental data for cold-formed structural steel and compiling the required data-sets. The data-sets are used to assess the environmental impact of an existing steel building and identify how and to what extent the environment is burdened by its construction. The findings of the research include the aforementioned environmental data which can be used in environmental analyses related to construction projects, while additional conclusions concerning the environmental impact of steel buildings in terms of quantity and type were also drawn.     

Concentration of radionuclides in hydrosphere affected by Temelín Nuclear Power Plant in Czech Republic

The paper presents results of a long-term field study of the possible impact of Temelín NPP on the Vltava and Elbe Rivers. The study was divided into 2 stages: before and after the operation of the NPP. The main goal of the investigation before the operation (1989–2000) was to determine the background levels of radionuclides resulting from the tests of nuclear weapons and the Chernobyl accident for different components of the environment. The paper discusses also the risk of a river radioactive contamination due to the tritium discharges in wastewater from Temelín NPP. During the operation period of 2001–2006, the results of the monitoring did not detect any impact of Temelín NPP on the concentrations of activation and fission products in the hydrosphere, apart from tritium. The annual average tritium concentrations in the Vltava River correspond with the previously calculated predictions for the conditions of the average and minimum guaranteed flows. The maximum concentration of tritium of 26.6 Bq/l in Vltava River at Prague was observed after dry period in 2003.     

Simulation of the dispersion of nuclear contamination using an adaptive Eulerian grid model

Application of an Eulerian model using layered adaptive unstructured grids coupled to a meso-scale meteorological model is presented for modelling the dispersion of nuclear contamination following the accidental release from a single but strong source to the atmosphere. The model automatically places a finer resolution grid, adaptively in time, in regions were high spatial numerical error is expected. The high-resolution grid region follows the movement of the contaminated air over time. Using this method, grid resolutions of the order of 6 km can be achieved in a computationally effective way. The concept is illustrated by the simulation of hypothetical nuclear accidents at the Paks NPP, in Central Hungary. The paper demonstrates that the adaptive model can achieve accuracy comparable to that of a high-resolution Eulerian model using significantly less grid points and computer simulation time.