Thermal processing of paper sludge and characterisation of its pyrolysis products

Paper sludge is a waste product from the paper and pulp manufacturing industry that is generally disposed of in landfills. Pyrolysis of paper sludge can potentially provide an option for managing this waste by thermal conversion to higher calorific value fuels, bio-gas, bio-oils and charcoal. This work investigates the properties of paper sludge during pyrolysis and energy required to perform thermal conversion. The products of paper sludge pyrolysis were also investigated to determine their properties and potential energy value. The dominant volatile species of paper sludge pyrolysis at 10 °C/min were found to be CO and CO₂, contributing to almost 25% of the paper sludge dry weight loss at 500 °C. The hydrocarbons (CH₄, C₂H₄, C₂H₆) and hydrogen contributed to only 1% of the total weight loss. The bio-oils collected at 500 °C were primarily comprised of organic acids with the major contribution being linoleic acid, 2,4-decadienal acid and oleic acid. The high acidic content indicates that in order to convert the paper sludge bio-oil to bio-diesel or petrochemicals, further upgrading would be necessary. The charcoal produced at 500 °C had a calorific value of 13.3 MJ/kg.     

Analysis of the combustion and pyrolysis of dried sewage sludge by TGA and MS

In this study, the combustion and pyrolysis processes of three sewage sludge were investigated. The sewage sludge came from three wastewater treatment plants.Proximate and ultimate analyses were performed. The thermal behaviour of studied sewage sludge was investigated by thermogravimetric analysis with mass spectrometry (TGA-MS). The samples were heated from ambient temperature to 800 °C at a constant rate 10 °C/min in air (combustion process) and argon flows (pyrolysis process). The thermal profiles presented in form of TG/DTG curves were comparable for studied sludges. All TG/DTG curves were divided into three stages. The main decomposition of sewage sludge during the combustion process took place in the range 180–580 °C with c.a. 70% mass loss. The pyrolysis process occurred in lower temperature but with less mass loss. The evolved gaseous products (H₂, CH₄, CO₂, H₂O) from the decomposition of sewage sludge were identified on-line.     

Characterization of alkali-activated thermally treated incinerator bottom ash

The fine fraction (<14mm) of incinerator bottom ash (IBA) obtained from a UK energy from waste plant has been milled and thermally treated at 600, 700, 800 and 880 degrees C. Treated materials have been activated with Ca(OH)(2) (10wt%) and the setting times and compressive strengths at different curing times measured. In addition to decomposition of CaCO(3) to CaO, thermal treatment increases the content of gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)). Thermally treated samples were significantly more reactive than milled IBA and heating to 700 degrees C produced a material which rapidly set. Silica, gehlenite and wollastonite were the main crystalline phases present in hydrated samples and a mixed sulphate-carbonate AFm-type phase (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33).11H(2)O) formed. Significant volumes of gas were generated during curing and this produced a macro-porous microstructure that limited strength to 2.8MPa. The new materials may have potential for use as controlled low-strength materials.     

Efficiency of a blast furnace slag cement for immobilizing simulated borate radioactive liquid waste

The efficiency of a blast furnace slag cement (Spanish CEM III/B) for immobilizing simulated radioactive borate liquid waste [containing H3BO3, NaCl, Na2SO4 and Na(OH)] has been evaluated by means of a leaching attack in de-mineralized water at the temperature of 40 degrees C over 180 days. The leaching was carried out according to the ANSI/ANS-16.1-1986 test. Moreover, changes of the matrix microstructure were characterized through porosity and pore-size distribution analysis carried out by mercury intrusion porosimetry (MIP), X-ray diffraction (XRD) and thermal analysis (TG). The results were compared with those obtained from a calcium aluminate cement matrix, previously published.     

低温等离子体协同催化降解含硫恶臭污染物

采用共沉淀—喷涂法制备了（Cu5Mn7Zr1O22）0.08/（γ-Al2O3）0.1/堇青石蜂窝陶瓷催化剂。表征结果显示：催化剂孔隙率较高,表面均匀分散着粒径介于20~100 nm的晶体颗粒。以硫化氢和乙硫醇为典型含硫恶臭污染物进行了低温等离子体协同催化降解实验,结果表明：污染物的降解率随着输入功率的增加而提高;与单纯低温等离子体相比,低温等离子体协同催化能获得更好的降解效果。降解机理可能为：在高能电子和活性粒子作用下,H2S或C2H5SH分子中键能较弱的H—S、C—S和C—C键断裂形成·SH、·C2H5、·CH2SH、·CH3等小碎片基团,这些小碎片基团进一步发生聚合、氧化或自由基链式反应,最终降解为CO2、SO2、SO3、H2O等无毒小分子。     

Reduction of tar using cheap catalysts during sewage sludge gasification

Solid-fuel conversion or gasification study of sewage sludge and energy recovery has become increasingly important because energy recovery and climate change are emerging issues. Various types of catalysts, such as dolomite, steel slag and calcium oxide, were tested for tar reduction during the sewage sludge gasification process. For the experiments on sewage sludge gasification reactions and tar reduction using the catalysts, a fixed bed of laboratory-scale experimental apparatus was set up. The reactor was made of quartz glass using an electric muffle furnace. The sewage sludge samples used had moisture contents less than 6%. The experimental conditions were as follows: sample weight was 20 g and reaction time was 10 min, gasification reaction temperature was from 600 to 800°C, and the equivalence ratio was 0.2. The quantity of catalysts was 2–6 g, and temperatures of catalyst layers were 500–700°C. As the reaction temperature increased up to 800°C, the yields of gaseous products and liquid products increased, whereas char and tar products decreased, showing effects on gas product compositions. These results were considered to be due to the increase of the water-gas reaction and Boudouard reaction. In the case of experiments with catalysts, dolomite (4 g), steel slag (6 g) and calcium oxide (6 g) were used. When the temperature of catalysts increased, the weight of the tar produced decreased with different cracking performances by different catalysts. Reforming reactions were considered to occur on the surface of dolomite, steel slag and calcium oxide, causing cracking of the hydrocarbon structure, which eventually showed reduced tar generation.     

Influences of chemical activators on incinerator bottom ash

This research has applied different chemical activators to mechanically and thermally treated fine fraction (<14 mm) of incinerator bottom ash (IBA), in order to investigate the influences of chemical activators on this new pozzolanic material. IBA has been milled and thermally treated at 800 degrees C (TIBA). The TIBA produced was blended with Ca(OH)(2) and evaluated for setting time, reactivity and compressive strength after the addition of 0.0565 mole of Na(2)SO(4), K(2)SO(4), Na(2)CO(3), K(2)CO(3), NaOH, KOH and CaCl(2) into 100g of binder (TIBA+Ca(OH)(2)). The microstructures of activated IBA and hydrated samples have been characterized by X-ray diffraction (XRD) and thermogravimetry (TG) analysis. Thermal treatment is found to produce gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)) phases. The thermally treated IBA samples are significantly more reactive than the milled IBA. The addition of Na(2)CO(3) can increase the compressive strength and calcium hydroxide consumption at 28-day curing ages. However, the addition of Na(2)SO(4), K(2)SO(4), K(2)CO(3), NaOH and KOH reduces the strength and hydration reaction. Moreover, these chemicals produce more porous samples due to increased generation of hydrogen gas. The addition of CaCl(2) has a negative effect on the hydration of TIBA samples. Calcium aluminium oxide carbonate sulphide hydrate (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33)(H(2)O)(11)) is the main hydration product in the samples with activated IBA, except for the sample containing CaCl(2).     

Recovery of copper and cobalt from ancient slag.

About 2.5 million tonnes of copper smelter slag are available in Küre, northern part of Turkey. This slag contains large amounts of metallic values such as copper and cobalt. A representative slag sample containing 0.98% Cu, 0.49% Co and 51.47% Fe was used in the experimental studies. Two different methods, direct acid leaching and acid baking followed by hot water leaching were used for recovering Cu and Co from the slag. The effects of leaching time, temperature and acid concentration on Cu- and Co-dissolving efficiencies were investigated in the direct acid leaching tests. The optimum leaching conditions were found to be a leaching time of 2 h, acid concentration of 120 g L(-1), and temperature of 60 degrees C. Under these conditions, 78% Cu and 90% Co were extracted. In the acid baking + hot water leaching tests, 74% Co was dissolved after 1 h of roasting at 200 degrees C using a 3:1 acid:slag ratio, whereas the Cu-dissolving efficiency was 79% and the total slag weight loss was approximately 50%.     

Physico-chemical treatment of marble processing wastewater and the recycling of its sludge.

In the first part of this study, the treatability of marble processing wastewater by the coagulation-flocculation process was investigated. Optimum coagulant-flocculant doses for turbidity removal in wastewater from the cutting, faience and equalization processes were determined as 500, 200 and 500 ppm of Al2(SO4)3; 300, 500 and 300 ppm of FeCl3 and 600, 400 and 200 ppm of Agrofloc 100 (AGRON Water Treatment Technologies and Chemical Marketing Industry and Trade Limited Company, Izmir, Turkey), respectively. It was found that the removal of total solids from cutting and equalization process wastewaters was highest for the 100 ppm dosage of all chemicals used. The amount of total solids removed from faience process wastewater by Agrofloc 100 was higher than that removed by the other chemicals used. The removals of suspended solids from cutting, faience and equalization process wastewaters were similar to each other for each of the chemicals. The pH values after treatment by Agrofloc 100 were higher than the values determined after treatment by other chemicals for all process wastewater. Electrical conductivity values, however, were lower for Agrofloc 100 than for the others. Settled sludge volume experiments showed that settled sludge volumes decreased with time. The results of the quiescent settling experiment showed that the settling type could be termed flocculent settling. In the second part of the study, the usage of waste sludge from marble processing as an additive material in cement was investigated. The waste sludge originated from the wastewaters of different steps of the marble processing plant. Waste sludge was replaced with cement at various percentages by weight to prepare the mixtures of mortar. The specimens poured into the moulds were held for 24 h, removed from the moulds and held again for 28 days in lime-saturated water at 23 degrees C. Compressive and flexural strengths were evaluated with respect to percentages of waste sludge replaced with cement. The maximum compressive and flexural strengths were observed for specimens containing a 6% waste sludge when compared with control and it was also found that waste sludge up to 9% could effectively be used as an additive material in cement.     

Determination of Cu and Ni incorporation ratios in Portland cement clinker

Cu and Ni are metals found in galvanic sludges; these sludges are considered hazardous due to their heavy metal content. The main objective of this work is to determine the incorporation amount of Cu and Ni in Portland clinker when a galvanic sludge containing these metals is added to the clinker raw-material. The influence of this addition on the clinkering reactions is evaluated as well as the possibility of co-incinerating galvanic sludges containing Cu and Ni in rotary cement kilns. This study also characterizes the galvanic sludge. Samples were prepared by additions from 0.25 to 5 wt.% of a galvanic sludge to an industrial clinker raw-material. The clinkering process was simulated in a laboratory device. The following techniques were applied to characterize the raw materials and the products of the tests: chemical analysis, differential thermal analysis (DTA) and thermogravimetric analysis (TG). Leaching tests were performed in the produced clinker samples in order to verify the incorporation of the studied metals in the clinker structure. The results led to the conclusion that additions of up to 2 wt.% of a galvanic sludge containing 2.4 wt.%Cu and 1.2 wt.% Ni to clinker raw-material do not affect the clinkering reactions and that these metals are totally incorporated into the clinker.     

Experimental and kinetic modeling of oxygen-enriched air combustion of municipal solid waste

The characteristics of oxygen-enriched air combustion of raw municipal solid waste (MSW) were studied by thermogravimetric analysis. Experiments on oxidative pyrolysis of MSW were carried out under different atmospheres (N(2), N(2):O(2)=7:3, N(2):O(2)=5:5, N(2):O(2)=4:6, and N(2):O(2)=2:8) at 30 degrees C/min. Two distinct peaks of weight loss were obtained according to the derivative thermogravimetric curves; one of them is centered on 305 degrees C with about 40% weight loss, and the second is centered on 420 degrees C with about 20% weight loss. Effects of oxygen concentration on the decomposition process and char combustion were analyzed, and then the process of oxygen-enriched air combustion of MSW was divided into four steps. Kinetic parameters were observed by direct non-linear regressions. According to the obtained data, the apparent activation energy and reaction order decreases along with the combustion process, while that of char combustion increases as oxygen concentration increases.     

Recovery of nickel oxide from spent catalyst

This study investigates the possibility of recovering nickel from the spent catalyst (NiO/Al2O3) resulting from the steam reforming process to produce water gas (H2/H2O) in many industries. In the extraction process, nickel is recovered as sulfate using sulfuric acid as a solvent. The considered parameters affecting nickel recovery were acid concentration, temperature and time of digestion solid:liquid ratio, particle size and stirring rate. Nickel was to be directly recovered as a sulfate salt by direct crystallization method. The conversion was 99% at 50% sulfuric acid concentration, solid: liquid ratio (1:12) by weight, particle size less than 500 micron for more than 5 h and 800 rpm at 100 degrees C.     

Fixation and partitioning of heavy metals in slag after incineration of sewage sludge

Fixation of heavy metals in the slag produced during incineration of sewage sludge will reduce emission of the metals to the atmosphere and make the incineration process more environmentally friendly. The effects of incineration conditions (incineration temperature 500-1100°C, furnace residence time 0-60min, mass fraction of water in the sludge 0-75%) on the fixation rates and species partitioning of Cd, Pb, Cr, Cu, Zn, Mn and Ni in slag were investigated. When the incineration temperature was increased from 500 to 1100°C, the fixation rate of Cd decreased from 87% to 49%, while the fixation rates of Cu and Mn were stable. The maximum fixation rates for Pb and Zn and for Ni and Cr were reached at 900 and 1100°C, respectively. The fixation rates of Cu, Ni, Cd, Cr and Zn decreased as the residence time increased. With a 20min residence time, the fixation rates of Pb and Mn were low. The maximum fixation rates of Ni, Mn, Zn, Cu and Cr were achieved when the mass fraction of water in the sludge was 55%. The fixation rate of Cd decreased as the water mass fraction increased, while the fixation rate of Pb increased. Partitioning analysis of the metals contained in the slag showed that increasing the incineration temperature and residence time promoted complete oxidation of the metals. This reduced the non-residual fractions of the metals, which would lower the bioavailability of the metals. The mass fraction of water in the sludge had little effect on the partitioning of the metals. Correlation analysis indicated that the fixation rates of heavy metals in the sludge and the forms of heavy metals in the incinerator slag could be controlled by optimization of the incineration conditions. These results show how the bioavailability of the metals can be reduced for environmentally friendly disposal of the incinerator slag.     

Gasification of refuse derived fuel in a fixed bed reactor for syngas production

Steam gasification of two different refuse derived fuels (RDFs), differing slightly in composition as well as thermal stability, was carried out in a fixed-bed reactor at atmospheric pressure. The proximate and ultimate analyses reveal that carbon and hydrogen are the major components in RDFs. The thermal analysis indicates the presence of cellulose and plastic based materials in RDFs. H2 and CO are found to be the major products, along with CO2 and hydrocarbons resulting from gasification of RDFs. The effect of gasification temperature on H2 and CO selectivities was studied, and the optimum temperature for better H2 and CO selectivity was determined to be 725 degrees C. The calorific value of product gas produced at lower gasification temperature is significantly higher than that of gas produced at higher process temperature. Also, the composition of RDF plays an important role in distribution of products gas. The RDF with more C and H content is found to produce more amounts of CO and H2 under similar experimental conditions. The steam/waste ratio showed a notable effect on the selectivity of syngas as well as calorific value of the resulting product gas. The flow rate of carrier gas did not show any significant effect on products yield or their distribution.     

Effect of fly ash addition on the removal of hydrogen sulfide from biogas and air on sewage sludge-based composite adsorbents

Desulfurization adsorbents were prepared from the mixtures of various compositions of New York City sewage sludge and fly ashes from SASOL, South Africa, by pyrolysis at 950 degrees C. The resulting materials were used as adsorbents of hydrogen sulfide from simulated dry digester gas mixture or moist air. The adsorbents before and after H(2)S removal were characterized using adsorption of nitrogen, elemental analysis, pH measurements, XRF, XRD, and thermal analysis. It was found that the addition of fly ash decreases the desulfurization capacity in comparison with the sewage sludge-based materials. The extent of this decrease depends on the type of ash, its content and the composition of challenging gas. Although the presence of CO(2) deactivates some adsorption sites to various degrees depending on the sample composition, the addition of ashes has a more detrimental effect when the adsorbents are used to remove hydrogen sulfide from air. This is likely the result of hydrophobicity of ashes since the H(2)S removal capacity was found to be strongly dependent on the reactivity towards water/water adsorption. On the other hand, the addition of ashes strongly decreases the porosity of materials where sulfur, as a product of hydrogen sulfide oxidation, can be stored.     

Recovery of valuable metals from electronic and galvanic industrial wastes by leaching and electrowinning

In the present paper, a study on laboratory scale to perform a treatment for valuable metals recovery from electronic and galvanic industrial wastes, is reported. The characterisation of the waste, performed by XRD, SEM, EDX and chemical analysis, showed a high metals content in the sludge, such as Cu, Ni, Mn, Pb, Sn, W. A leaching process, coupled by electrowinning, is then proposed in order to reduce the volume of the waste material and to recover selectively valuable metals, such as Cu and Ni. During the leaching step, carried out by using H(2)SO(4), several factors were investigated (acid concentration, temperature and time of treatment). The leached liquor has been successfully treated with an electrowinning process, to recover copper and nickel. The copper and nickel depositions, were performed in acid and alkaline conditions, respectively. The Faraday yield was of about 95%. The energy consumption was 2.13 and 4.43 kWh per kg of copper and nickel recovered, respectively. At the end of the process, about 94-99% of the initial content of Cu and Ni was recovered at the cathode. The experimental results obtained, showed the technical feasibility of the process.     

Oxygen-enriched air for co-incineration of organic sludges with municipal solid waste: a pilot plant experiment

Pilot-plant experiments were performed to evaluate the effect of oxygen enrichment on the co-incineration of MSW and organic sludge from a wastewater treatment facility. Combustion chamber temperatures, stack gas concentrations, i.e., CO(2) and CO, and the residual oxygen were measured. The maximum ratio of organic sludge waste to total waste input was 30 wt.%. Oxygen-enriched air, 22 vol.% (dry basis) oxygen, was used for stable combustion. As the co-incineration ratio of the sludge increased, the primary and secondary combustion chamber temperatures were decreased to 900 and 750 degrees C, respectively, approximately 100 degrees C below the proper incineration. However, if the supplied air was enriched with 22 vol.% (dry basis) oxygen content, the incinerator temperature was high enough to burn the waste mixture containing 30 wt.% moisture sludge, with an estimated heating value of 6.72 MJ/kg. There are two main benefits of using oxygen enrichment in the co-incineration. First, the sensible heat can be reduced as the quantity of nitrogen in the flue gas will be decreased. Second, the unburned carbon formation is reduced due to the oxygen-enriched burning of the waste, despite an increase in the sludge co-incineration ratio.     

Vacuum pyrolysis of waste tires with basic additives

Granules of waste tires were pyrolyzed under vacuum (3.5-10kPa) conditions, and the effects of temperature and basic additives (Na(2)CO(3), NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50wt% was achieved at 480 degrees C by adding 3wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) approximately 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na(2)CO(3) addition. Pyrolysis gas was mainly composed of H(2), CO, CH(4), CO(2), C(2)H(4) and C(2)H(6). Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5wt%) was much higher.     

The hydration characteristics and utilization of slag obtained by the vitrification of MSWI fly ash

This study investigated the effects of slag composition on the hydration characteristics of slag blended cement (SBC) pastes. Synthetic slag samples were prepared by melting CaO-modified and Al(2)O(3)-modified municipal solid waste incinerator (MSWI) fly ash. MSWI fly ash was mixed with 5% CaO and 5% Al(2)O(3) (by weight), respectively, resulting in two fly ash mixtures. These mixtures were then melted at 1400 degrees C for 30 min to produce two types of slag with different contents, designated at C-slag and A-slag. Both the C-slag and A-slag samples exhibited a pozzolanic activity index higher than the unmodified slag sample. The results show that the synthetic slags all met the Taiwan EPA's current regulatory thresholds. These synthetic slags were then blended with ordinary Portland cement (OPC) at various weight ratios ranging from 10 to 40%. The 28-day strength of the C1 paste was higher than that developed by the OPC paste, suggesting that the C-slag contributed to the earlier strength of the SBC pastes. At curing times beyond 28 days, the strength of the A1 paste samples approached that of the OPC paste samples. It can be seen from this that increasing the amount of calcium and aluminum oxide increases the early strength of SBC. The C-slag blended cement paste samples showed an increase in the number of fine pores with the curing time, showing that the C-slag enhanced the pozzolanic reactions, filling the pores. Also, the incorporation of a 10% addition of C-slag also tended to enhance the degree of hydration of the SBC pastes during the early ages (3-28 days). However, at later ages, no significant difference in degree of hydration between the OPC pastes and the SBC pastes was observed with the 10% C-slag addition. However, the incorporation of A-slag did decreased the degree of hydration. A slag blend ratio of 40% significantly decreased the hydration degree.     

Properties of alkali-activated systems with stone powder sludge

This article investigates the effects of stone powder sludge on the microstructure and strength development of alkali-activated fly ash and blast furnace slag mixes. Stone powder sludge produced from a crushed aggregate factory was used to replace fly ash and granulated blast furnace slag at replacement ratios of 0%, 10%, 20%, and 30% by mass. The unit weight and compressive strength of the samples were measured, and scanning electron microscopy/energy dispersive spectroscopy and X-ray diffraction (XRD) analyses were performed. The test results indicated that the compressive strength of alkali-activated blast furnace slag mixes using stone powder sludge was higher than that of the alkali-activated blast furnace slag control mix, but the compressive strength of alkali-activated fly ash mixes decreased with increasing replacement ratio of stone powder sludge. Microscopy results indicated that for alkaliactivated blast furnace slag samples, broken surfaces were more evident than for the alkali-activated fly ash samples. For all XRD diagrams, broad and diffuse peaks were observed around 2θ = 35° (d = 2.96–3.03 Å), implying amorphous or short-ordering structure phases.