明沟导流构建湿地系统处理橡胶生产性废水

明沟导流构建湿地系统处理天然橡胶生产性废水 ,工程投资低 ,占地面积小 ,运行稳定 ,易于管理 ,处理率高 ;引入废水后即自然启动 ,在自然条件下稳定、长期运行 ,操作管理简单方便。处理后排放废水各项指标均达到 GB8978-1996《污水综合排放标准》的二级标准     

酵母菌处理马铃薯淀粉废水研究

马铃薯淀粉废水属高浓度废水,COD达到30 000 mg/L左右,BOD为15 000 mg/L左右,可生化性较好。针对废水中主要含有淀粉、蛋白质和可溶性纤维等成分,筛选分离出能降解这些有机成分的6种酵母。以废水为培养液分别培养这6种酵母及其混合菌,实验结果表明,各酵母菌株对该废水都有较好的降解效果,混合菌的处理效果要好于单个菌株。在连续流废水培养条件下,混合酵母活性和菌体量也较高,MLSS稳定在12 g/L左右,其COD去除率稳定在77%左右。     

膜萃取处理高浓度工业苯胺废水

大连市某药业公司生产中产生的高浓度苯胺废水可生化性极差,传统工艺处理该废水难度大,且不能回收利用苯胺.采用膜萃取工艺处理该废水,工艺运行稳定,苯胺去除率高.实验结果表明,在进水流量为3.05 L/d、反应温度为50 ℃、萃取液pH≈1、膜管长18 m条件下,进水苯胺质量浓度为33 081 mg/L时,苯胺去除率稳定在97%以上.进行经济核算,每吨废水净收益为103.84元.     

不同来源高浓度有机废水的集中处理

按照水质情况,将多种来源于不同工业生产过程中的高浓度有机废水划分为高悬浮固体乳化液废水、难生化高浓度有机废水、高悬浮固体不含油有机废水、含铬有机废水和杂质含量较少的乳化液废水5类,分别采用酸化破乳/Fen-ton氧化/混凝/絮凝、Fenton氧化/混凝/絮凝、混凝/絮凝、还原/混凝/絮凝、震动膜过滤技术作为生化预处理技术,并通过小试和中试验证了各技术的效果。实验结果表明,按照上述分类结果,采用不同预处理技术可以得到良好的效果,废水水质明显改善,满足继续生化处理的基本条件。各预处理生产装置处理效果稳定,同时生化系统已经稳定运行120天以上,COD去除率超过90%,出水经过低剂量的Fenton试剂处理后可达到《污水排入城镇下水道水质标准》(CJ343-2012)。     

UASB反应器处理PTA废水的研究

采用UASB反应器，对两种不同方法驯化的污泥处理PTA废水进行了研究，结果表明，经对苯二甲(TA)酸驯化的厌氧污泥能够稳定地处理PTA废水，在水力停留时间29～32h、进水CODcr4600-7000mg／L、废水中对TA含量1800～2080mg／L条件下，CODcr的去除率稳定在80％以上，对TA去除率稳定在70％以上；而用PTA废水驯化的污泥在同样的条件下对CODcr，去除率在61％以下，对TA去除率在40％以下。经TA驯化的污泥，其物理、生物性状比PTA废水驯化的污泥有显著提高和改善。     

共固定光合和发酵性细菌处理有机废水生物制氢技术

介绍了光合细菌和发酵性细菌处理有机废水生物制氢技术,并提出了将两者混合培养是处理有 机废水生物制氢技术的最佳代谢模式,而共固定光合和发酵性细菌则是高效,稳定净化有机废水持续嫌氢的最佳工艺。     

江苏泛佳亚麻纺织厂有限公司废水治理工程设计

以江苏泛佳亚麻纺织厂有限公司处理2000m^3／d废水的工程实例，对亚麻类织品染色和整理废水探索一种操作性较强、达标较稳定的治理方法。通过该工艺处理，废水达到GB4287-92表3一级排放标准。     

序批式活性污泥法工艺处理含盐废水动力学模型研究

为了实现含盐废水序批式活性污泥法(SBR)工艺的启动,采用逐步提高废水中NaCl浓度负荷的方法对活性污泥进行驯化,并建立有机物(COD)与NH4+-N的降解动力学模型。结果表明,经过280d的驯化和稳定运行,SBR系统可以有效降解含盐废水,COD去除率高于74%,NH4+-N平均去除率高于90%,实现了SBR工艺处理含盐废水的启动和稳定运行。含盐废水有机物(COD)降解动力学参数r0(无盐条件下的COD去除速率)为129.87mg/(L.h),KY(盐抑制常数)为7700.01mg/L;含盐废水硝化反应动力学参数Ks(饱和常数)为186.52mg/L,vmax(NH4+-N的最大比降解速率)为0.0034h-1。     

预酸化下营养剂添加量对生物沥浸处理洗毛废水的影响

洗毛废水是洗毛生产工艺排出的兼具高COD、高悬浮固体浓度、高色度、难固液分离等典型特征,且对环境存在潜在污染的一类工业废水。通过摇瓶实验,研究了预酸化条件下,生物沥浸技术对洗毛废水的处理效果。结果表明,当洗毛废水经预酸化至p H 5.5、营养剂浓度≥4 g/L、回流比例为1∶1的情况下,3个批次实验内复合菌群生物沥浸过程稳定,洗毛废水能够很好地完成生物沥浸过程。反应结束后体系p H稳定在3.0左右,COD去除率高达90%以上,色度由原来的1 875倍降到20倍,沉淀中油脂去除率高于65%,且比阻降低至原来的0.2%~0.3%。而在对照处理中,体系p H值稳定在8.0左右,COD去除率小于10%,油脂去除率不足10%,洗毛废水比阻仅降低20%。因此,采用预酸化及生物沥浸作用有利于洗毛废水酸化处理的连续运行并具有良好的应用前景。     

清污分质法处理啤酒废水的工程应用

分析了应用厌氧UASB技术分质处理啤酒高浓度酿造废水,并将此废水与其他低浓度废水混合进入新型生物接触氧化工艺处理。根据工艺的设计、调试和工程实际运行情况表明,该工艺具有技术先进、高效低耗、运行稳定、投资省、管理简单、出水水质好等特点。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.