DBD反应器关键操作参数对2,4-二氯酚去除的影响

采用同轴喷雾式介质阻挡放电(DBD)反应器处理2,4-二氯酚(2,4-DCP)模拟废水,考察了水质、废水流量、载气流量、放电频率等关键操作参数对2,4-DCP去除的影响。自来水中的CO₃^2-/HCO₃^-能够中和生成的硝酸/亚硝酸(载气含N₂),同时也能清除放电过程中产生的自由基,因而不利于2,4-DCP的去除。在DBD反应器的操作参数中,载气流量对于活性组分的产生及气相到液相的传质有显著影响,是最为关键的操作参数。反应器操作参数的变化会影响放电过程。同轴式反应器和废水雾化对污染物的矿化有利。在废水流量50 mL/min、载气流量15 L/min、放电频率17 kHz的最佳条件下处理60 min,2,4-DCP和TOC的去除率分别为69.77%和31.85%。     

宁东能源化工基地核心区表层土壤酚类污染物的污染评价、空间分布及来源解析

采集了宁东能源化工基地核心区的146个表层土壤样品,检测了6种优控酚类污染物.运用单因子污染指数、内梅罗综合污染指数和致癌风险指数评价了酚类污染物的污染程度及健康风险.借助主成分分析和绝对主成分分数-多元线性回归受体模型,结合地统计学方法,对酚类污染物的空间分布及来源进行了分析.结果显示:2,4-二氯酚和2,4,6-三...     

Quantification of Polymerisation Processes During The Oxidative Degradation of 14C-Labelled Chlorophenols

In experiments employing the lignocellulose-decaying basidiomycetes Trametes versicolor and Stropharia rugosoannulata degrading uniformly¹⁴C-labelled 2,4-dichlorophenol and pentachlorophenol, acombination of size exclusion chromatography (SEC),fractionation, and -scintillation counting wasapplied to quantify polymerisation products formed duringchlorophenol degradation. Time-dependent mass balances weregenerated by analysis of ¹⁴C in polymerisation products,CO₂, as well as monomer non-polar and polar metabolites.Approximately 30% of the chlorophenols were found to bepolymerised. A major fraction of the polymerised productscorresponded to a molecular weight range from 0.24 – 40 kDa.Only a minor fraction could be attributed to a molecularweight >40 kDa. This method proved to be useful inquantification of polymerisation products and kinetics of thepolymerisation processes, whereas UV/Vis detection ofpolymerisation products separated by SEC led to false positiveresults. The SEC-¹⁴C method could also be applied forother complex processes where polymerisation ordepolymerisation occurs (humification, degradation oflignocellulose, formation of bound residues from xenobioticssuch as polycyclic aromatic hydrocarbons or 2,4,6-trinitrotoluene) and where spectrophotometric determinationsare difficult or impossible.     

Kinetics of microbial landfill methane oxidation in biofilters

A methane oxidizing biofilter system fitted to the passive venting system of a harbor sludge landfill in Germany was characterized with respect to the the methanotrophic population, methane oxidizing capacity, and reaction kinetics. Methanotrophic cell counts stabilized on a high level with 1.3 x 10(8) to 7.1 x 10(9) cells g dw(-1) about one year after first biofilter operation, and a maximum of 1.2 x 10(11) cells g dw(-1). Potential methane oxidizing activity varied between 5.3 and 10.7 microg h(-1) g dw(-1). Cell numbers correlated well with methane oxidation activities. Extrapolation of potential activities gave methane removal rates between 35 and 109 g CH4 h(-1) m(-3), calculated for 30 degrees C. Optimum temperature was 38 degrees C for freshly sampled biofilter material and 22 degrees C for a methanotrophic enrichment culture grown at 10 degrees C incubation temperature. Substrate kinetics revealed the presence of a low-affinity methane oxidizing community with a high Vmax of 1.78 micromol CH4 h(-1) g ww(-1) and a high K(M) of 15.1 microM. K(MO2) for methane oxidation was 58 microM. No substantial methane oxidizing activity was detected below 1.7-2.6 vol.-% O2 in the gaseous phase. Methane deprivation led to a decrease in methane oxidation activity within 5-9 weeks but could still be detected after 25 weeks of substrate deprivation and was fully restored within 3 weeks of continuous methane supply. Very high salt loads are leached from the novel biofilter material, expanded clay, yielding electric conductivity values of up to 15 mS cm(-1) in the leachate. Values > 6 mS cm(-1) were shown to depress methane consumption. Water retention characteristics of the material proved to be favourable for methane oxidizing systems with a gas permeable volume of 78% of bulk volume at field capacity water content. Correspondingly, no influence of water content on methane oxidation activity could be detected at water contents between 2.5 and 20 vol.-%.     

Complex co‐substrate addition increases initial petroleum degradation rates during land treatment by altering bacterial community physiology

A pilot‐scale land treatment unit (LTU) was constructed at the former Guadalupe oil production field with the purpose of investigating the effect of co‐substrate addition on the bacterial community and the resulting rate and extent of total petroleum hydrocarbon (TPH) degradation. The TPH was a weathered mid‐cut distillate (C10‐C32) excavated from the subsurface and stockpiled before treatment. A control cell (Cell 1) in the LTU was amended with nitrogen and phosphorus while the experimental cell (Cell 2) was amended with additional complex co‐substrate—corn steep liquor. During the pilot LTU operation, measurements were taken of TPH, nutrients, moisture, aerobic heterotrophic bacteria (AHB), and diesel oxidizing bacteria (DOB). The bacterial community was also assayed using community‐level physiology profiles (CLPP) and 16S rDNA terminal restriction fragment (TRF) analysis. TPH degradation in both cells was characterized by a rapid phase of degradation that lasted for the first three weeks, followed by a slower degradation phase that continued through the remainder of the project. The initial rate of TPH‐degradation in Cell 1 (?0.021 day^?1) was slower than in Cell 2 (?0.035 day^?1). During the slower phase, degradation rates in both cells were similar (?0.0026 and ?0.0024 respectively). AHB and DOB counts were similar in both cells during the fast degradation phase. A second addition of co‐substrate to Cell 2 at the beginning of the slow degradation phase resulted in an increased AHB population that lasted for the remainder of the project but did not affect TPH degradation rates. CLPP data showed that co‐substrate addition altered the functional capacity of the bacterial community during both phases of the project. However, TRF data indicated that the phylogenetic composition of the community was not different in the two cells during the fast degradation phase. The bacterial phylogenetic structure in Cell 2 differed from Cell 1 after the second application of co‐substrate, during the slow degradation phase. Thus, co‐substrate addition appeared to enhance the functional capacity of the bacterial community during the fast degradation phase when the majority of TPH was bioavailable, resulting in increased degradation rates, but did not affect rates during the slow degradation phase when the remaining TPH may not have been bioavailable. These data show that co‐substrate addition might prove most useful for applications such as land farming where TPH is regularly applied to the same soil and initial degradation rates are more important to the project goals. © 2003 Wiley Periodicals, Inc.     

A Novel Hybrid 2,4-Dichlorophenoxy Acetate Bead from Modified Cassava Starch and Sodium Alginate with Modified Natural Rubber Coating

A novel herbicide bead was developed by phase separation, utilizing modified cassava starch (CSt), sodium alginate (SA) and 2,4-dichlorophenoxy acetate (2,4 DA), and the beads were also coated with natural rubber grafted with cassava starch (NR-graft-CSt) to aid their water resistance. The alginate gel beads with 65% entrapped 2,4 DA showed 90% release within 24 h. The incorporation of CSt in the beads markedly improved their encapsulation efficiency to 98% and sustained the release of the herbicide for 700 h. The water resistance was improved by coating the beads with NR-graft-CSt when compared with the pure CSt/SA bead. The synthesized bead has excellent potential for agricultural applications.     

Carbon mineralization dynamics in soils amended with meat meals under laboratory conditions

Meat and bone meal (MBM) is obtained from the wastes produced during slaughtering operations. Its high concentration of N and P makes it interesting as an organic fertiliser but its use in soil has been barely studied previously. In this work four laboratory experiments were performed to study the influence of different variables (MBM composition, rate of application, temperature of incubation and the type of soil) on C mineralization dynamics of MBM in agricultural soils. The total CO2-C evolved (as % of added C) after 2 weeks ranged between 10% and 20%. The kinetics of mineralization were rapid, with C evolved as CO2 within the first 4 days representing more than 50% of total C mineralized. A linear correlation was found between the rate of application (added-C) and CO2-C evolved (r2: 0.997; P<0.001). A temperature coefficient (Q10) was used to assess the difference in biological activity at 5 degrees C intervals. Q10, which ranged from 1.0 to 2.7 (250h), was higher for the lower temperature range (Q10 (15-20 degrees C)>Q10 (20-25 degrees C)) and it was found to be related to the soil properties. Finally, the mineralization process was found to be highly dependent upon the different soil factors, although no simple linear correlation was found between mineralization and soil properties.     

A respirometric method to measure mineralization of polymeric materials in a matured compost environment

A respirometric method was developed to measure the mineralization of polymeric materials in a matured compost environment. For the purpose of evaluating the method, results obtained for the mineralization of glucose and cellulose are presented. The matured compost, in addition to supplied nutrients, micronutrients, and an inoculum, serves as the matrix which supports the microbial activity. Recovery of the substrate carbon in the form of carbon dioxide from the glucose and cellulose added to test vessels was 68 and 70%, respectively. A statistical evaluation of the results obtained on substrate mineralization was carried out and showed acceptable reproducibility between replicate test vessels and test runs. The testing protocol developed has the following important characteristics: (1) the test reactors are maintained at 53 °C at a high solids loading (60% moisture), which has certain characteristics that are similar to a thermophilic compost environment; (2) the test matrix providing microbial activity is derived from readily available organic materials to facilitate reproducibility of the method in different laboratories; (3) the equipment required to perform this test is relatively inexpensive; and (4) the information obtained on polymer mineralization is vital to the study and development of biodegradable polymeric materials.Guest Editor: Dr. Graham Swift, Rohm & Haas.     

Influences of chlorine content on emission of HCl and organic compounds in waste incineration using fluidized beds

HCl and some organic compounds are the precursors of polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) in municipal solid waste incinerators. In this work, a lab-scale fluidized bed incinerator is adopted to study the relationship between the organic and the inorganic chlorine contents of artificial wastes and the emissions of HCl and organic compounds. The lower threshold limit (LTL) of chlorine content below which HCl and organic compounds are not generated is studied. Experimental results showed that organic chlorides had a greater potential to release chlorine than inorganic chlorides. The generation of organic pollutants fell, but the emissions of HCl increased with the temperature. The concentrations of chlorophenols (CPs)/chlorobenzenes (CBs) increased with chlorine contents. No LTL existed for HCl regardless of whether CaO was added. The LTL for CPs was between 0.1 and 0.3wt% of inorganic chloride, but there was none for organic sources. For CBs, the LTL was between 0.5 and 1.0wt% for inorganics at 700 and 800 degrees C, but 0.1-0.3 wt% at 700 degrees C and 0.3-0.5 wt% at 800 degrees C for organics. The production of PAHs and benzene, toluene, ethylbenzene and xylene (BTEX) was related to the surplus hydrogen ions that were not reacted with the chlorine. Adding CaO inhibited the production of HCl, CBs and CPs, but did not seriously affect PAHs and BTEX.     

Organic–Inorganic Hybrid Coatings for the Modification of Barrier Properties of Poly(lactic acid) Films for Food Packaging Applications

Organic–inorganic hybrid coatings based on poly(ε-caprolactone), poly(ethylene oxide) or poly(lactic acid) as organic phase and silica from tetraethoxysilane as inorganic phase were prepared by the sol–gel approach. Coatings were applied onto poly(lactic acid) films for food packaging in order to improve its barrier properties towards oxygen and water vapour. All the prepared coatings were dense, homogeneous layers characterized by a good adhesion to the substrate. The permeance of the coating layers resulted one order of magnitude lower than that of the uncoated poly(lactic acid) (PLA) film. The hydrophilic character of the coating did not permit to gain a significant decrease in the water vapour permeance. The perfect visual transparency of the coatings allows their application without worsening of the esthetical properties of the substrate PLA film.     

Sulphur mineralization kinetics of cattle manure and green waste compost in soils.

Sulphur mineralization of cattle manure (CM) and green waste compost (GWC) added to six agricultural soils with different chemical properties was monitored over 10 weeks in a laboratory incubation experiment. Although the amount of sulphur was higher in CM than in GWC, the cumulative SO4(2-)-S values in GWC-treated soils were higher than in soil amended with CM. The percentages of mineralized S were always higher in GWC-treated soil (in the range 1.3-8.5%) than in CM-treated soil (in the range 0.9-3.8%). In three of the six soils, particularly for CM, an immobilization of sulphur was observed. Three kinetic models were evaluated for their suitability to describe the mineralization process. The first-order model best described S mineralization for both amended and control soils. The GWC substantially increased the amount of potentially mineralizable S (S0) relative to the controls. In GWC-treated soils, the rates of S mineralization (k) were higher than rates in the controls. The k of CM-amended soils was often lower than the k of control soils. Parameters derived from the model were tested as indices for assessing the relationships between S mineralization and soil characteristics. The S0 was positively correlated to the amount of cumulative SO4(2-)-S and also to the content of organic C, N and S in soil.     

Comparison of several maturity indicators for estimating phytotoxicity in compost-amended soil

Compost can provide a rich organic nutrient source and soil conditioner for agricultural and horticultural applications. Ideal compost amendment rates, however, vary based on starting material and compost maturity or their interaction, and there is little consensus on appropriate methods to gauge maturity. In this study, electrical conductivity, carbon-to-nitrogen ratio, and carbon mineralization measurements were made on compost-amended soils and compared to phytotoxicity measured as cress (Lepidium sativum) germination. Cress germination in soil and compost mixtures incubated for 8-10 days significantly decreased with increasing electrical conductivity and carbon mineralization rate of the mixture and with carbon mineralization rate and mineralizable carbon associated with the compost. Cress germination was not related to carbon-to-nitrogen ratio or pH of soil and compost mixtures. The electrical conductivity of the soil and compost mixtures significantly decreased with decreasing mineralizable carbon suggesting that compounds contributing to electrical conductivity were present in the compost and decomposed upon soil amendment. The results of this study indicate that measurements of mineralizable carbon and mineralization rate of composts in soil, and electrical conductivity and mineralization rate of soil and compost mixtures, can be used as indicators of compost maturity.     

Modelling C and N mineralization during decomposition of anaerobically digested and composted municipal solid waste.

Application of municipal solid waste (MSW) to arable land can be used to close the nutrient cycle between urban and rural areas. The aim of the current study was to quantify net N mineralization and respiration from composted MSW (CMSW) and anaerobically digested MSW (ADMSW) applied to soil, and to test whether a simple relationship between net N mineralization and respiration that was developed for plant materials, was applicable for these types of MSW. In a laboratory experiment, CMSW and ADMSW were incorporated into soil and incubated at 15 degrees C. During the 149-day experiment, netN mineralization and respiration were determined. Cumulative respiration derived from both MSW types was very steep during the first 30 days, after which it levelled off. However, calculated on the basis of applied C, the ADMSW was 10 times more degradable than the CMSW. Both MSW types caused initial net N immobilization followed by re-mineralization. A simple model based on the relationship between net N mineralization and respiration was only applicable for the MSW after significant modifications. If farmers are to recognize CMSW and ADMSW as valuable fertilizers, it is important that they can be produced with higher maturity, in order to avoid initial N immobilization.     

基于MICP技术的再生骨料改性研究综述

分析总结了微生物矿化技术对再生骨料堆积密度、吸水率、压碎指标3个方面性能的影响,结果显示,微生物矿化技术处理后的再生骨料物理力学性能有明显改善,且改善效果与微生物活性和处理时间有重要关联。     

Physical modelling of the composting environment: a review. Part 2: Simulation performance

This paper reviews previously published heat balance data for experimental and full-scale composting reactors, and then presents an evaluation of the simulation performance of laboratory and pilot-scale reactors, using both quantitative and qualitative temperature profile characteristics. The review indicates that laboratory-scale reactors have typically demonstrated markedly different heat balance behaviour in comparison to full-scale systems, with ventilative heat losses of 36-67%, and 70-95% of the total flux, respectively. Similarly, conductive/convective/radiative (CCR) heat losses from laboratory reactors have been reported at 33-62% of the total flux, whereas CCR losses from full-scale composting systems have ranged from 3% to 15% of the total. Full-scale windrow temperature-time profiles from the literature were characterised by the present authors. Areas bounded by the curve and a 40 degrees C baseline (A(40)) exceeded 624 degrees C. days, areas bounded by the curve and a 55 degrees C baseline (A(55)) exceeded 60 degrees C days, and times at 40 and 55 degrees C were >46 days and >24 days, respectively, over periods of 50-74 days. For forced aeration systems at full scale, values of A(40) exceeded 224 degrees C days, values of A(55) exceeded 26 degrees C days, and times at 40 and 55 degrees C were >14 days and >10 days, respectively, over periods of 15-35 days. Values of these four parameters for laboratory-scale reactors were typically considerably lower than for the full-scale systems, although temperature shape characteristics were often similar to those in full-scale profiles. Evaluation of laboratory-, pilot- and full-scale profiles from systems treating the same substrate showed that a laboratory-scale reactor and two pilot-scale reactors operated at comparatively high aeration rates poorly simulated full-scale temperature profiles. However, the curves from two moderately insulated, self-heating, pilot-scale reactors operated at relatively low aeration rates appeared to closely replicate full-scale temperature profiles. The importance of controlling aeration rates and CCR losses is discussed and further work suggested in order to investigate the links between simulation of the composting environment and process performance.     

Simulated marine respirometry of biodegradable polymers

Eleven microorganisms were isolated from several temperate marine locations in the northeast Altantic coast of the United States and one tropical location in the Pacific Ocean (Hawaii) for the purpose of developing a rapid and accurate method of screening biodegradable materials for their susceptibility to mineralization. The materials evaluated in this study included chemically modified starch, amylose and pullulan, poly(3-hydroxybutyrate-co-valerate), (PHB/V), cellulose acetate, and a modified lignin/styrene. Some of the soluble, unmodified, biologically produced substrates such as starch, pullulan, and amylose mineralized rapidly. In general, the synthetic, insoluble polymers and the chemically modified polymers, such as acetylated and chlorinated amylose and pullulan, mineralized more slowly, although the ultimate mineralization of some of the substituted polysaccharides equaled or exceeded that of the unmodified substrate. The insoluble bacterial polyester, PHB/V, degraded rapidly after a short induction period. Initial respiration rate data, in general, could not be used as a predictor of ultimate mineralization. It was found that the cumulative level of carbon dioxide evolved signifies the minimum extent of biodegradation of the substrate, and the oxygen consumed is a good indicator of the maximum extent of substrate degradation.Paper presented at the Biodegradable Materials and Packaging Conference, September 22–23, 1993, Natick, Massachusetts.     

DNAPL Source Depletion: 1. Predicting Rates and Timeframes

Given the relatively rapid rate of dense nonaqueous‐phase liquid (DNAPL) ganglia depletion, source zones are generally dominated by horizontal layers of DNAPL after a release to the saturated zone. Estimating the time required to attain specific source strength reduction targets resulting from partial DNAPL source depletion is challenging due to a lack of available screening models, and because little has been done to synthesize available empirical data. Analytical and semi‐analytical models are used to study general DNAPL pool dissolution dynamics. The half‐life for the decline in DNAPL source strength (i.e., aqueous mass discharge) is demonstrated as proportional to the square root of the pool length, the thickness of the pool, and the solubility for single component DNAPLs. The through‐pool discharge is shown to be potentially significant for thin pools or in upper regions of thicker pools. An empirical analysis is used to evaluate average concentration decline rates for 13 in situ chemical oxidation (ISCO) and 16 enhanced in situ bioremediation (EISB) sites. Mean apparent decline rates, based on the time required to achieve the observed source strength reduction, are calculated for the ISCO and EISB sites (half‐lives of 0.39 year and 0.29 year, respectively). The empirical study sites are shown to have faster decline rates than for a large, complex study site where ISCO was implemented (half‐life of 2.5 years), and for a conceptual pool‐dominated trichloroethene source zone where EISB was simulated (half‐life of 2.5 years). Guidance is provided on using these findings in estimating timeframes for partial DNAPL depletion goals. © 2014 Wiley Periodicals, Inc.     

Improving the adsorption capacity and solid structure of natural volcanic soil using a foaming-sintering process based on recycled polyethylene terephthalate (PET).

The volcanic soils of southern Chile have demonstrated a high capacity to adsorb environmental pollutants, but for an industrial application, a stable solid material is necessary. The objective of this work was to produce a stable ceramic material through a process involving volcanic soil-polyurethane foam produced with recycled polyethylene terephthalate (PET)-polyols, and further thermal treatment. The selected foam formulation with 35.4% volcanic soil (< 63 microm) seems to be the most suitable for thermal treatment, with temperature steps at 700, 850, 1000 and 1200 degrees C. The porous ceramic material obtained has a stable solid form and an improved chlorophenols adsorption capacity (comparable to natural zeolites) that makes it suitable for advanced wastewater treatment and landfill leachate depuration.     

Extraction of heavy metal ions from waste colored glass through phase separation

A new method utilizing phase separation phenomena for the extraction of heavy metal ions used as colorants in colored glass is proposed. Colored soda-lime-silica glass containing Co or Cr as a colorant was remelted with B2O3 to yield soda-lime-borosilicate glass. The soda-lime-borosilicate glass thus obtained was leached in 1M nitric acid at 90 degrees C to dissolve the borate phase. All cations (Na, Ca, Cr and Co) concentrated in the borate phase are successfully leached out with the dissolution of the borate phase, when the amount of the B2O3 added to the glass and heat treatment conditions are properly chosen. Porous silicate glass powders with high SiO2 purity are obtained as the result of the leaching. Porous glass can also be formed as bulk material by controlling the composition of additives during the remelting.     

盐析分相微萃取—高效液相色谱法测定水中含氯除草剂

采用盐析分相微萃取—高效液相色谱法同时测定水中3种含氯除草剂,建立并优化了反相离子对液相色谱条件,考察了萃取剂种类、盐析剂的种类和加入量及试样pH对萃取效果的影响。对氯苯氧乙酸、2,4-二氯苯氧乙酸和2,4-滴丁酯的质量浓度在0.1~100.0mg/L内与色谱峰面积呈良好的线性关系,相关系数不低于0.9992。平均回收率分别为96.29%、79.16%和70.21%,相对标准偏差小于5.3%。该方法操作简便、绿色环保,适合于水中含氯除草剂的测定。