斜发沸石处理氨氮废水

以斜发沸石为吸附剂处理氨氮废水,研究了斜发沸石粒径、反应时间、废水pH、废水氨氮初始浓度、斜发沸石用量对吸附的影响,分析了斜发沸石的吸附动力学和热力学特征。结果表明,在298 K下,当斜发沸石用量为7 g/100 mL,沸石粒径小于74μm,废水氨氮初始浓度为200 mg/L,pH为7,吸附时间为3 h时,废水中氨氮的去除率可达到92.71%,斜发沸石吸附氨氮符合拟二级动力学方程。在温度为298~318 K之间时,吸附等温线更好地符合Freundlich方程。在此基础上,热力学计算发现,ΔH00、ΔG00、ΔS00,表明氨氮在斜发沸石上的吸附是自发吸热过程,以物理吸附为主。     

天然沸石对海水中氨氮的吸附特性

以天然沸石为吸附剂进行吸附海水中氨氮实验研究,考察了沸石粒径、反应液pH值和盐度对吸附效果的影响,对吸附动力学和热力学特性进行了探讨。实验结果表明,天然沸石粒径越小,越有利于其对海水中氨氮的吸附,反应液pH值对氨氮吸附影响较小,但在碱性条件下NH+4能够与海水中的Mg2+、PO3-4反应生成Mg NH4PO4·6H2O沉淀,导致反应液氨氮平衡浓度降低。随着海水盐度梯度增加,天然沸石对氨氮的吸附量呈显著下降趋势。天然沸石对海水中氨氮的吸附是快速吸附、缓慢平衡的过程,吸附过程较好地满足准二级动力学模型。吸附等温线更好地符合Langmuir等温吸附方程,通过热力学计算发现,△G0为负值,而△H0和△S0均为正值,说明天然沸石对海水中氨氮的吸附是吸热易发过程。     

改性沸石对二级生化出水中氨氮的吸附特性

采用氯化钠联合高温对天然斜发沸石进行改性,通过批次实验探究改性沸石吸附氨氮特性。结果表明:氯化钠浓度为0.8 mol·L~(-1),焙烧温度为300℃条件下,氨氮去除效果最佳;改性沸石在氨氮初始浓度为8mg·L~(-1),投加量为10 g·L~(-1),反应时间为120 min的条件下,去除率可达71%,相比天然沸石提高23.1%。通过扫描电镜(SEM)、X射线能谱(EDS)、比表面积(BET)、X射线衍射(XRD)和傅里叶光谱(FT-IR)考察改性前后沸石组成特征以及化学键的变化,可以看出,改性机制可去除孔道杂质及Na~+置换沸石中金属阳离子;氨氮吸附过程满足拟二级动力学方程(R~2=0.986),Langmuir等温线模型拟合结果 (R~2=0.998)优于Freundlich模型(R~2=0.839),且改性沸石最大吸附容量为5.94 mg·L~(-1)。热力学计算结果表明,沸石对氨氮的吸附过程是一个自发、吸热、熵增过程。上述结果表明,改性沸石能够有效地对污水厂二级生化出水中氨氮进行深度处理。     

天然和CPB改性沸石对Hg^2＋的吸附特征

通过静态实验研究溴代十六烷基吡啶（CPB）改性沸石和天然沸石对废水中Hg^2＋的吸附特性,探讨了吸附动力学、吸附平衡和吸附热力学机制。研究表明：Langmuir方程能较好地描述2种沸石对Hg^2＋的吸附,CPB改性沸石对Hg^2＋的吸附率得到显著提高。实验条件下,改性沸石对Hg^2＋的吸附率从67．5％提高到98．9％,吸附容量从0．521mg／g提高到3．07mg／g。利用准一级动力学方程、假二级动力学方程、颗粒内扩散模型和Elovich方程分别对动力学过程进行拟合,发现2种沸石对Hg^2＋的吸附均满足假二级动力学方程,且离子的颗粒内扩散对整个吸附过程有影响。动力学拟合、D-R方程拟合和热力学研究综合表明：2种沸石对Hg^2＋的吸附既存在化学吸附又存在物理吸附,吸附吉布斯自由能变（△G^0）、焓变（△H^0）、熵变（△S^0）均小于0,反应为自发的放热反应,低温有利于吸附的进行。     

多介质渗透反应格栅中氨氮的转化与存在形态

在利用渗透反应格栅技术修复地下水氨氮污染过程中,掌握氨氮在不同介质环境中的转化规律及存在形态对多介质渗透反应格栅中各介质作用及氮转化过程的控制十分重要.针对进水氨氮浓度约10 mg/L的模拟地下水,以天然河沙、释氧材料、斜发沸石及海绵铁为反应介质,设计了一套多介质渗透反应格栅模拟氨氮在各介质环境中的转化及归宿.结果表明,在天然河沙层,氨氮优先被河沙吸附固定,但去除量有限(△C＜1.5 mg/L),氨氮主要以离子态溶于模拟地下水.在好氧沸石层,氨氮经沸石吸附及生物硝化协同作用几乎被完全去除,该层出水氨氮浓度低于0.01 mg/L,且氮主要存在形态为硝酸盐氮(C=10～26.6 mg/L).在铁厌氧层,部分硝酸盐氮经海绵铁化学还原和生物反硝化作用,分别被转化为氨氮(△C=2～9.5 mg/L)和氮气(△C＜8 mg/L),其余硝酸盐氮以离子态继续存留于模拟地下水.     

天然和CPB改性沸石对Hg2+的吸附特征

通过静态实验研究溴代十六烷基吡啶(CPB)改性沸石和天然沸石对废水中Hg2+的吸附特性,探讨了吸附动力学、吸附平衡和吸附热力学机制。研究表明:Langmuir方程能较好地描述2种沸石对Hg2+的吸附,CPB改性沸石对Hg2+的吸附率得到显著提高。实验条件下,改性沸石对Hg2+的吸附率从67.5%提高到98.9%,吸附容量从0.521 mg/g提高到3.07 mg/g。利用准一级动力学方程、假二级动力学方程、颗粒内扩散模型和Elovich方程分别对动力学过程进行拟合,发现2种沸石对Hg2+的吸附均满足假二级动力学方程,且离子的颗粒内扩散对整个吸附过程有影响。动力学拟合、D-R方程拟合和热力学研究综合表明:2种沸石对Hg2+的吸附既存在化学吸附又存在物理吸附,吸附吉布斯自由能变(△G0)、焓变(ΔH0)、熵变(ΔS0)均小于0,反应为自发的放热反应,低温有利于吸附的进行。     

低浓度氨氮废水的离子交换法脱氮

分别研究了沸石的等温吸附模型,改性沸石在交换柱中的穿透与再生,通过化学沉淀法对再生废液中氨氮的回收等。结果显示:60～80目单位重量天然斜发沸石对氨氮的饱和交换容量为4.15 mg/g;30 mg/L的氨氮废水经过交换柱后沸石的穿透吸附容量和平衡吸附容量分别为:4.50 mg/g和4.757 mg/g。化学再生后,用化学沉淀法使再生废液中氨氮由202 mg/L降到16.3 mg/L。     

沸石法工业污水氨氮治理技术研究

本文研究了斜发沸石法去除工业污水中氨氮的方法 ,通过沸石对NH+4 的全交换容量、吸附和洗脱工艺条件对去除氨氮效果影响的试验 ,确定了处理氨氮废水的工艺流程和适宜参数。结果表明 ,在废水浓度pH =7的条件下 ,沸石对铵的平均全交换容量达到 12 .96mg/g沸石 ,且交换容量随PH值的增大而降低 ;高速低温有利于吸附 ,低速高温有利于洗脱 ;处理后污水氨氮含量低于 5 0mg/L ,达到了国家排放标准。本研究可为治理氨氮废水技术开发提供了一定的技术依据     

氢氧化铝胶体对2,2′,4,4′-四溴联苯醚的吸附

溴代阻燃剂多溴联苯醚(polybrominated diphenyl ethers,PBDEs)是一种被广泛使用的阻燃剂,其对神经、甲状腺、肝脏等具有潜在毒性。其中,2,2′,4,4′-四溴联苯醚(BDE-47)作为一种重要单体,在环境介质中被广泛检出。胶体是环境中污染物迁移过程中的重要载体,它对有机污染物在土壤-地下水系统中的迁移有不可忽略的影响。开展典型无机胶体氢氧化铝胶体对BDE-47的吸附动力学和吸附热力学研究,以期为BDE-47在土壤-地下水中的迁移提供理论依据。结果表明:Sips等温吸附方程对该吸附过程拟合效果最佳(R_(adj)~2=0.943 94),计算得出氢氧化铝胶体对BDE-47的饱和吸附量为609.37 mg·g~(-1);吸附动力学实验结果显示,准二级反应动力学方程拟合氢氧化铝胶体对BDE-47吸附反应过程最佳(R_(adj)~20.95),同时该吸附反应速率随BDE-47浓度的升高逐渐减小;Van't Hoff方程拟合表明,吸附热力学参数标准反应焓变△H~0=40.506 kJ·mol~(-1)、标准反应熵变△S~0=0.075 7 kJ·(mol·K)~(-1),标准反应吉布斯自由能△G~0(298 K)=17.98 kJ·mol~(-1)。此外,反应体系的pH和阳离子种类及浓度均会影响氢氧化铝胶体对BDE-47的吸附过程。     

斜发沸石对城市污水处理厂二级出水中氨氮的处理效果研究

通过静态实验,研究天然斜发沸石去除城市污水处理二级出水中氨氮的性能。研究结果表明,投加量越大,沸石对废水中氨氮的去除率越高,但是吸附容量越低;沸石对氨氮的去除具有短时间内快速吸附,然后缓慢平衡的特点;粉末状沸石对氨氮的去除效果明显好于颗粒状沸石;pH对氨氮去除率有显著影响,pH值为6时,沸石对氨氮的去除率最高。NaCl和NaOH溶液对沸石的改性具有明显的效果,HCl溶液对沸石的改性作用不明显。     

天然沸石颗粒对NH4+动态吸附过程中的离子交换特性研究

采用天然斜发沸石颗粒,进行了沸石吸附水溶液中NH4+的动态吸附实验研究.实验结果表明,沸石颗粒粒径、沸石床高度、上升流速、进水氨氮浓度、进水水质等因素对沸石颗粒吸附NH4+有着明显的影响,在工程实践应用时,要根据动态吸附实验结果选择合适的设计及运行参数.离子交换机理研究表明,Na+首先被交换出来,随着反应进行,Ca2+...     

改性沸石对低浓度氨氮废水的动态吸附

采用氯化钠溶液对甘肃白银天然沸石改性,以低浓度氨氮(NH4+-N)废水为处理对象,对比了天然沸石和改性沸石的动态吸附特性并绘制穿透曲线,利用Origin软件对实验数据分析处理,得出穿透曲线的通式。结果表明:在相同条件下,改性沸石的穿透时间和吸附饱和时间都比天然沸石的长约1.5倍;沸石经氯化钠改性后,对NH4+-N的吸附速率和饱和吸附量都明显提高,吸附性能显著改善。Origin软件对水溶液中NH4+-N的吸附穿透曲线的Logistic模型回归式具有较高的精度,该模型可以很好地反映沸石吸附剂的动态吸附过程。     

黄河兰州段悬移质泥沙对氨氮的吸附特性

实验研究了黄河兰州段不同粒径的悬浮泥沙对氨氮的吸附行为,拟阐释黄河兰州段水质自净的机制。通过分析探讨了含沙量、氨氮初始浓度、泥沙粒径和化学成分对氨氮吸附过程的影响。结果表明,准二级动力学方程和Langmuir模型能够较好地描述黄河兰州段不同粒径泥沙的吸附动力学和等温吸附过程(R20.9);含沙量对泥沙吸附氨氮作用具有显著影响,且氨氮吸附量和平衡时间与含沙量呈明显负相关性;氨氮初始浓度与氨氮吸附量及平衡时间呈正相关性;同时,泥沙颗粒越细,吸附氨氮的能力越强,吸附容量越大,反应的自发程度越高。此外,泥沙有机质、Fe2O3、Al2O3和MgO的含量随粒径减小而增大,它们对单位质量泥沙最大吸附量(Sm)具有正效应。泥沙的吸附在黄河兰州段水质自净过程中起着一定的促进作用。     

沸石改性及其去除水中氨氮的实验研究

通过实验研究了沸石改性条件及其对水中氨氮吸附去除的影响。结果表明,加热改性与无机酸改性不能显著提高沸石对氨氮的吸附量。利用NaOH改性的最佳浓度为1 mol/L,此条件下对氨氮吸附量可提高到650.68 mg/kg,为天然沸石的2.82倍。利用无机盐改性时,对氨氮吸附效果最好的是NaCl改性沸石,其次为KCl改性沸石与CaCl₂改性沸石。随着NaCl溶液浓度和改性时间的增加,改性沸石对氨氮的吸附量显著增加,可达天然沸石的3～4倍;在NaCl浓度为150 g/L与改性时间为18 h条件下,改性沸石对氨氮吸附量可达887.35 mg/kg,为天然沸石的3.84倍。     

改性沸石吸附低浓度氨氮废水及其脱附的研究

采用氯化钠溶液对浙江某地天然沸石改性,以低浓度氨氮废水为处理对象,比较了天然沸石和改性沸石的吸附等温线、吸附动力学和动态吸附,并进行了改性沸石的动态脱附研究.结果表明,沸石的平衡吸附量随着平衡浓度的增大而增大;Freundlich方程比Langmuir方程更好地描述沸石吸附低浓度氨氮废水的行为,改性沸石比天然沸石具有更...     

4A沸石分子筛处理中低浓度氨氮废水

利用天然沸石、采用水热合成法制备4A沸石分子筛,用XRD和SEM进行了表征。通过考察吸附剂用量、pH、共存金属阳离子、吸附时间、氨氮废水初始浓度、温度对吸附性能的影响,结合动力学方程、吸附等温线、热力学函数等研究了吸附性能和机理。结果表明,当4 g/L的4A沸石分子筛在废水pH值为4~8的条件下对中低浓度氨氮吸附120min后,去除率可达88%;废水中共存单一金属阳离子(Pb2+、Cu2+、Ca2+和Mg2+)浓度大于100 mg/L时,对中低浓度的NH+4有强烈的竞争吸附;氨氮的吸附过程较好地符合准二级动力学方程、Freundlich模型,是一种混乱度增加、自发的放热过程。     

Adsorption of elemental mercury vapors from synthetic exhaust combustion gas onto HGR carbon

An activated carbon commercially available named HGR, produced by Calgon-Carbon Group, was used to adsorbe metallic mercury. The work is part of a wider research activity by the same group focused on the removal of metallic and divalent mercury from combustion flue gas. With respect to previously published papers, this one is aimed at studying in depth thermodynamic equilibria of metallic mercury adsorption onto a commercial activated carbon. The innovativeness lies in the wider operative conditions explored (temperature and mercury concentrations) and in the evaluation of kinetic and thermodynamic data for a commercially available adsorbing material. In detail, experimental runs were carried out on a laboratory-scale plant, in which Hg° vapors were supplied in a nitrogen gas stream at different temperature and mercury concentration. The gas phase was flowed through a fixed bed of adsorbent material. Adsorbate loading curves for different Hg° concentrations together with adsorption isotherms were achieved as a function of temperature (120, 150, 200°C) and Hg° concentrations (1.0?7.0 mg/m³). Experimental runs demonstrated satisfying results of the adsorption process, while Langmuir parameters were evaluated with gas–solid equilibrium data. Especially, they confirmed that adsorption capacity is a favored process in case of lower temperature and they showed that the adsorption heat was –20 kJ/mol. Furthermore, a numerical integration of differential equations that model the adsorption process was proposed. Scanning electron microscopy (SEM) investigation was an useful tool to investigate about fresh and saturated carbon areas. The comparison between them allowed identification of surface sites where mercury is adsorbed; these spots correspond to carbon areas where sulfur concentration is greater.

Implications: Mercury compounds can cause severe harm to human health and to the ecosystem. There are a lot of sources that emit mercury species to the atmosphere; the main ones are exhaust gases from coal combustion and municipal solid waste incineration. Furthermore, certain CO₂ capture processes, particularly oxyfuel combustion in a pulverized fuel coal-fired power station, produce a raw CO₂ product containing several contaminants, mainly water vapor, oxygen, and nitrogen but also mercury, that have to be almost completely removed; otherwise these would represent a strong drawback to the success of the process.     

Kinetic, equilibrium isotherm and thermodynamic studies of Cr(VI) adsorption onto low-cost adsorbent developed from peanut shell activated with phosphoric acid

A particular agricultural waste, peanut shell, has been used as precursor for activated carbon production by chemical activation with H₃PO₄. Unoxidized activated carbon was prepared in nitrogen atmosphere which was then heated in air at a desired temperature to get oxidized activated carbon. The prepared carbons were characterized for surface area, surface morphology, and pore volume and utilized for the removal of Cr(VI) from aqueous solution. Batch mode experiments were conducted to study the effects of pH, contact time, particle size, adsorbent dose, initial concentration of adsorbate, and temperature on the adsorption of Cr(VI). Cr(VI) adsorption was significantly dependent on solution pH, and the optimum adsorption was observed at pH 2. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used to analyze the kinetic data obtained at different initial Cr(VI) concentrations. The adsorption kinetic data were described very well by the pseudo-second-order model. Equilibrium isotherm data were analyzed by the Langmuir, Freundlich, and Temkin models. The results showed that the Langmuir adsorption isotherm model fitted the data better in the temperature range studied. The adsorption capacity which was found to increase with temperature showed the endothermic nature of Cr(VI) adsorption. The thermodynamic parameters, such as Gibb’s Free energy change (ΔG°), standard enthalpy change (ΔH°), and standard entropy change (ΔS°) were evaluated.     

Influence of preparation method on structural,optical, magnetic,and adsorption properties of nano-NiFe2O4

Nickel ferrite (NiFe₂O₄) nanoparticles are prepared through different routes (microwave, co-precipitation, and pyrolysis) and tested for water purification applications through adsorption removal of an acid red dye B as a model organic pollutant. The characterizations of the prepared samples were done using XRD, FT-IR, SEM, TEM, BET, UV-Vis absorbance, Raman spectrum, and vibrating sample magnetometer (VSM). All samples showed an inverse spinel crystal structure. The obtained results pointed out to the effect of the synthetic route on the morphology, particle size, optical, and magnetic properties of the prepared ferrites. Magnetic measurements showed super-paramagnetic behavior for all samples. The magnetic saturation (M_s) of the sample prepared by pyrolysis, was found to possess the highest saturation value, 34.8 emu/g. Adsorption experiments were performed under the change in several parameters, such as pH, adsorbent dosage, and initial dye concentration. A dye removal percentage of 99% was reached under the optimum state. The isothermal adsorption of the acid red dye was investigated using several models, in which the experimental data could be best described by the Freundlich model. Several kinetic and equilibrium models were inspected by linear regression analysis and showed best fitting for the adsorption data through pseudo-second-order model. The calculated thermodynamic parameters indicated that the adsorption of acid red dye onto all the ferrite samples is a spontaneous and endothermic physical adsorption process.

     

Graphene—a promising material for removal of perchlorate (ClO4 −) from water

A batch adsorption process was applied to investigate the removal of perchlorate (ClO₄ ^?) from water by graphene. In doing so, the thermodynamic adsorption isotherm and kinetic studies were also carried out. Graphene was prepared by a facile liquid-phase exfoliation. Graphene was characterized by Raman spectroscopy, Fourier-transform infrared spectroscopy, powder X-ray diffraction, scanning electron microscope, and zeta potential measurements. A systematic study of the adsorption process was performed by varying pH, ionic strength, and temperature. The adsorption efficiency of graphene was 99.2 %, suggesting that graphene is an excellent adsorbent for ClO₄ ^? removal from water. The rate constants for all these kinetic models were calculated, and the results indicate that second-order kinetics model was well suitable to model the kinetic adsorption of ClO₄ ^?. Equilibrium data were well described by the typical Langmuir adsorption isotherm. The experimental results showed that graphene is an excellent perchlorate adsorbent with an adsorbent capacity of up to 0.024 mg/g at initial perchlorate concentration of 2 mg/L and temperature of 298 K. Thermodynamic studies revealed that the adsorption reaction was a spontaneous and endothermic process. Graphene removed the perchlorate present in the water and reduced it to a permissible level making it drinkable.