On-road measurement of vehicle tailpipe emissions using a portable instrument

A study design procedure was developed and demonstrated for the deployment of portable onboard tailpipe emissions measurement systems for selected highway vehicles fueled by gasoline and E85 (a blend of 85% ethanol and 15% gasoline). Data collection, screening, processing, and analysis protocols were developed to assure data quality and to provide insights regarding quantification of real-world intravehicle variability in hot-stabilized emissions. Onboard systems provide representative real-world emissions measurements; however, onboard field studies are challenged by the observable but uncontrollable nature of traffic flow and ambient conditions. By characterizing intravehicle variability based on repeated data collection runs with the same driver/vehicle/route combinations, this study establishes the ability to develop stable modal emissions rates for idle, acceleration, cruise, and deceleration even in the face of uncontrollable external factors. For example, a consistent finding is that average emissions during acceleration are typically 5 times greater than during idle for hydrocarbons and carbon dioxide and 10 times greater for nitric oxide and carbon monoxide. A statistical method for comparing on-road emissions of different drivers is presented. Onboard data demonstrate the importance of accounting for the episodic nature of real-world emissions to help develop appropriate traffic and air quality management strategies.     

Time-resolved ammonia measurement in vehicle exhaust

The objective of this study was to identify the influence of sampling and analytical approach on the quality of NH3 emission data of a gasoline-fuelled three-way catalyst vehicle. NH₃ concentration measurements have been performed in the tailpipe and in the diluted exhaust after a constant volume sampling (CVS) system during five different test cycles. Chemical ionisation mass spectrometry (CI-MS) and Fourier transform infrared spectroscopy (FTIR) were used to acquire ammonia concentrations in real-time. Independently, NH₃ emission rates were determined by continuous absorption of a flow-proportional sample of exhaust gas in diluted sulphuric acid and subsequent ion chromatography (IC). Ammonia emission rates ranged from 22–94 mg km^-1. The results of the three compared techniques are in good agreement. Furthermore, time-resolved ammonia emission profiles recorded by CI-MS and FTIR coincided with respect to emission levels as well as emission dynamics. However, in the dilution tunnel, severe ammonia adsorption was observed leading to long lasting memory effects or even analyte loss. Therefore, neither ammonia real-time emission data nor NH₃ emission rates should be acquired after a CVS system.     

Comparison of vehicle exhaust emissions from modified diesel fuels

Three diesel fuels, one oil sand-derived (OSD) diesel serving as base fuel, one cetane-enhanced base fuel, and one oxygenate [diethylene glycol dimethyl ether (DEDM)]-blended base fuel, were tested for their emission characterizations in vehicle exhaust on a light-duty diesel truck that reflects the engine technology of the 1994 North American standard. Both the cetane-enhanced and the oxygenate-blended fuels were able to reduce regulated [CO, particulate matter (PM), total hydrocarbon (THC)] and nonregulated [polyaromatic hydrocarbons (PAHs), carbonyls, and other volatile organic chemicals] emissions, except for nitrogen oxides (NO(x)), compared with the base fuel. Although burning a fuel that contains oxygen could conceivably yield more oxygenated compounds in emissions, the oxygenate-blended diesel fuel resulted in reduced emissions of formaldehyde along with hydrocarbons such as benzene, 1,3-butadiene, and PAHs. Reductions in nitro-PAH emissions have been observed in both the cetane-enhanced and oxygenated fuels. This further demonstrates the benefits of using a cetane enhancer and the oxygenated fuel component.     

Effects of vehicle exhaust emissions on urban wild plant species

Very few investigations have examined the direct impacts of vehicle exhausts on plants and attempted to separate out the key pollutants responsible for observed effects. This paper describes a multi-phase investigation into this topic, using 12 herbaceous species typical of urban areas and representing different functional groups. Fumigations were conducted in solardomes with diesel exhaust pollutants at concentrations designed to simulate those close to a major highway in inner London. A wide range of effects were detected, including growth stimulation and inhibition, changes in gas exchange and premature leaf senescence. This was complemented by controlled fumigations with NO, NO(2) and their mixture, as well as a transect study away from a busy inner London road. All evidence suggested that NO(x) was the key phytotoxic component of exhaust emissions, and highlights the potential for detrimental effects of vehicle emissions on urban ecosystems.     

Real-world vehicle emissions as measured by in situ analysis of exhaust plumes

Environmental Science and Pollution Research - We conducted a 60-day roadside measurement campaign on a busy street in Münster, Germany, during summer 2016. We used gas and particle...     

Estimation of road vehicle exhaust emissions from 1992 to 2010 and comparison with air quality measurements in Genoa,Italy

An investigation into road transport exhaust emissions in the Genoa urban area was performed by comparing the quantities of carbon monoxide (CO), nitrogen oxides (NO_x), nitrogen dioxide (NO₂) and particulate matter (PM) emitted by different vehicle categories with air quality measurements referred to the same pollutants. Exhaust emissions were evaluated by applying the PROGRESS (computer PROGramme for Road vehicle EmiSSions evaluation) code, developed by the Internal Combustion Engines Group of the University of Genoa, to eight different years (from 1992 to 2010), considering spark ignition and Diesel passenger cars and light duty vehicles, heavy duty vehicles and buses, motorcycles and mopeds. Changes in terms of vehicles number, mileage and total emissions are presented together with relative distributions among the various vehicle categories. By comparing 1992 and 2010 data, calculated trends show a 7% increase in the number of vehicles, with total mileage growing at a faster rate (approx. 22%); total emissions decrease considerably, by approximately 50% for NO_x and PM, 70% for HC and 80% for CO, due to improvements in engines and fuels forced by the stricter European legislation and the fleet renewal, while primary NO₂ emission will be very close to 1992 level, after a decrease of about 18% in 2000.Air quality was analysed by selecting traffic and background measuring stations from the monitoring network managed by the Environmental Department of the Province of Genoa: average annual concentrations of considered pollutants from 1994 to 2007 were calculated in order to obtain the relative historical trends and compare them with European public health limits and with road vehicle emissions. Though an important reduction in pollutant concentrations has been achieved as a consequence of cleaner vehicles, some difficulties in complying with present and/or future NO₂ and PM₁₀ limits are also apparent, thus requiring suitable measures to be taken by the local authorities.     

Trends of exhaust emissions from gasoline motor vehicles in the metropolitan area of Mexico city

Light duty gasoline vehicles account for most of CO, hydrocarbons and NO_x emissions to the urban environment in the metropolitan area of Mexico City. In order to ameliorate air pollution, several control measures have been imposed in the last decade, such as: up-grade of gasoline's quality, stringent environmental standards, and catalytic converters. On the other hand and from the beginning of 2001, Tier I emission standards became mandatory for all new model year sold in the country. Car manufacturers in Mexico do not guarantee the performance of their exhaust emissions systems for a given mileage. In this work, we present results on brand new vehicles that indicate that NO_x emission factors, though they are within the Tier I standard, deteriorate rapidly with the travelled distance (mileage).     

活性炭纤维在机动车尾气净化中的研究与应用展望

机动车尾气净化控制的一个难点在于冷启动阶段，此时由于温度较低，催化剂尚未完全起作用，导致排出的污染物浓度较高。阐述了活性炭纤维的基本特性，特别是其低温吸附与催化性能对NO和CO的转化作用，讨论了活性炭纤维作为机动车尾气净化材料所需的改性及方法，并展望了其应用前景。     

用空气加热器减少轻型汽油车低温冷启动时HC、CO 排放量的研究

按照《轻型汽车污染物排放限值及测量方法(中国Ⅲ、Ⅳ阶段)》(GB 18352.3-2005)的测试规范,在一辆轻型汽油车上使用空气加热器进行发动机进气预热,并测定了车辆低温冷启动时的HC、CO排放量.结果表明,发动机启动后24 s左右,HC的瞬态排放量达到最大值,HC的排放主要集中在启动后的前150 s左右;发动机启动...     

Development of molecular marker source profiles for emissions from on-road gasoline and diesel vehicle fleets

As part of the Gasoline/Diesel PM Split Study, relatively large fleets of gasoline vehicles and diesel vehicles were tested on a chassis dynamometer to develop chemical source profiles for source attribution of atmospheric particulate matter in California's South Coast Air Basin. Gasoline vehicles were tested in cold-start and warm-start conditions, and diesel vehicles were tested through several driving cycles. Tailpipe emissions of particulate matter were analyzed for organic tracer compounds, including hopanes, steranes, and polycyclic aromatic hydrocarbons. Large intervehicle variation was seen in emission rate and composition, and results were averaged to examine the impacts of vehicle ages, weight classes, and driving cycles on the variation. Average profiles, weighted by mass emission rate, had much lower uncertainty than that associated with intervehicle variation. Mass emission rates and elemental carbon/organic carbon (EC/OC) ratios for gasoline vehicle age classes were influenced most by use of cold-start or warm-start driving cycle (factor of 2-7). Individual smoker vehicles had a large range of mass and EC/OC (factors of 40 and 625, respectively). Gasoline vehicle age averages, data on vehicle ages and miles traveled in the area, and several assumptions about smoker contributions were used to create emissions profiles representative of on-road vehicle fleets in the Los Angeles area in 2001. In the representative gasoline fleet profiles, variation was further reduced, with cold-start or warm-start and the representation of smoker vehicles making a difference of approximately a factor of two in mass emission rate and EC/OC. Diesel vehicle profiles were created on the basis of vehicle age, weight class, and driving cycle. Mass emission rate and EC/OC for diesel averages were influenced by vehicle age (factor of 2-5), weight class (factor of 2-7), and driving cycle (factor of 10-20). Absolute and relative emissions of molecular marker compounds showed levels of variation similar to those of mass and EC/OC.     

Characterization of in-use light-duty gasoline vehicle emissions by remote sensing in Beijing: impact of recent control measures

China's national government and Beijing city authorities have adopted additional control measures to reduce the negative impact of vehicle emissions on Beijing's air quality. An evaluation of the effectiveness of these measures may provide guidance for future vehicle emission control strategy development. In-use emissions from light-duty gasoline vehicles (LDGVs) were investigated at five sites in Beijing with remote sensing instrumentation. Distance-based mass emission factors were derived with fuel consumption modeled on real world data. The results show that the recently implemented aggressive control strategies are significantly reducing the emissions of on-road vehicles. Older vehicles are contributing substantially to the total fleet emissions. An earlier program to retrofit pre-Euro cars with three-way catalysts produced little emission reduction. The impact of model year and driving conditions on the average mass emission factors indicates that the durability of vehicles emission controls may be inadequate in Beijing.     

Real-world vehicle emissions: A summary of the 15th coordinating research council on-road vehicle emissions workshop

The Coordinating Research Council held its 15th workshop in April 2005, with nearly 90 presentations describing the most recent mobile source-related emissions research. In this paper, the authors summarize the presentations from researchers who are engaged in improving our understanding of the contribution of mobile sources to air quality. Participants in the workshop discussed emission models and emission inventories, results from gas- and particle-phase emissions studies from spark-ignition and diesel-powered vehicles (with an emphasis in this workshop on particle emissions), effects of fuels on emissions, evaluation of in-use emissions control programs, and efforts to improve our capabilities in performing on-board emissions measurements, as well as topics for future research.     

A portable fiber-optic chemical device for the quantitative determination of carbon monoxide from automobile exhaust emissions

A colorimetric method for the quantitative determination of CO by diffuse reflectance is described. This method is based on the reduction by CO of Mo (VI) from the indicator reagent molybdosilicic acid (H8Si[Mo2O7]6). The reduction yielded a change of color from clear yellow to dark green on white disk filter chart paper wetted with reagent indicator solution. The gaseous mixture containing CO was forced to pass through this chart paper, initiating the reaction. The intensity of the color produced, measured by diffuse reflectance, was proportional to the CO concentration present in exhaust gases in the range from 0.02 to 12% volume/volume (v/v). A 650-nm light-emitting diode was used as a light source. A two-fiber-optic system carried the light from the source to the detection system, which was composed of a photodiode, an amplification circuit, and a digital display. The method was applied with success in field measurements for automobiles in the Otto cycle. In a previous paper, this method was used for the quantitative determination of exhaust emissions from diesel-fueled vehicles.     

The comparison of fossil carbon fraction and greenhouse gas emissions through an analysis of exhaust gases from urban solid waste incineration facilities

In this study, in order to understand accurate calculation of greenhouse gas emissions of urban solid waste incineration facilities, which are major waste incineration facilities, and problems likely to occur at this time, emissions were calculated by classifying calculation methods into 3 types. For the comparison of calculation methods, the waste characteristics ratio, dry substance content by waste characteristics, carbon content in dry substance, and ¹²C content were analyzed; and in particular, CO₂ concentration in incineration gases and ¹²C content were analyzed together. In this study, 3 types of calculation methods were made through the assay value, and by using each calculation method, emissions of urban solid waste incineration facilities were calculated then compared. As a result of comparison, with Calculation Method A, which used the default value as presented in the IPCC guidelines, greenhouse gas emissions were calculated for the urban solid waste incineration facilities A and B at 244.43 ton CO₂/day and 322.09 ton CO₂/day, respectively. Hence, it showed a lot of difference from Calculation Methods B and C, which used the assay value of this study. It is determined that this was because the default value as presented in IPCC, as the world average value, could not reflect the characteristics of urban solid waste incineration facilities. Calculation Method B indicated 163.31 ton CO₂/day and 230.34 ton CO₂/day respectively for the urban solid waste incineration facilities A and B; also, Calculation Method C indicated 151.79 ton CO₂/day and 218.99 ton CO₂/day, respectively.

Implications: This study intends to compare greenhouse gas emissions calculated using ¹²C content default value provided by the IPCC (Intergovernmental Panel on Climate Change) with greenhouse gas emissions calculated using ¹²C content and waste assay value that can reflect the characteristics of the target urban solid waste incineration facilities. Also, the concentration and ¹²C content were calculated by directly collecting incineration gases of the target urban solid waste incineration facilities, and greenhouse gas emissions of the target urban solid waste incineration facilities through this survey were compared with greenhouse gas emissions, which used the previously calculated assay value of solid waste.     

Effect of methyl tertiary butyl ether concentrations on exhaust emissions from gasoline used in the metropolitan area of Mexico City

In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.     

Real-world vehicle emissions: a summary of the tenth coordinating research council on-road vehicle emissions workshop

The Coordinating Research Council (CRC) held its tenth workshop in March 2000, focusing on results from the most recent real-world vehicle emissions research. In this paper, we summarize the presentations from researchers who are engaged in improving our understanding of the contribution of mobile sources to emission inventories. Participants in the workshop discussed efforts to improve mobile source emission models and emission inventories, results from gas- and particle-phase emissions studies from spark-ignition and diesel-powered vehicles, new methods for measuring mobile source emissions, improvements in vehicle emission control systems (ECSs), and evaluation of motor vehicle inspection/maintenance (I/M) programs, as well as topics for future research.     

Black carbon and polycyclic aromatic hydrocarbon emissions from vehicles in the United States-Mexico border region: pilot study

The investigators developed a system to measure black carbon (BC) and particle-bound polycyclic aromatic hydrocarbon (PAH) emission factors during roadside sampling in four cities along the United States-Mexico border, Calexico/Mexicali and El Paso/Juarez. The measurement system included a photoacoustic analyzer for BC, a photoelectric aerosol sensor for particle-bound PAHs, and a carbon dioxide (CO2) analyzer. When a vehicle with measurable emissions passed the system probe, corresponding BC, PAH, and CO2 peaks were evident, and a fuel-based emission factor was estimated. A picture of each vehicle was also recorded with a digital camera. The advantage of this system, compared with other roadside methods, is the direct measurement of particulate matter components and limited interference from roadside dust. The study revealed some interesting trends: Mexican buses and all medium-duty trucks were more frequently identified as high emitters of BC and PAH than heavy-duty trucks or passenger vehicles. In addition, because of the high daily mileage of buses, they are good candidates for additional study. Mexican trucks and buses had higher average emission factors compared with U.S. trucks and buses, but the differences were not statistically significant. Few passenger vehicles had measurable BC and PAH emissions, although the highest emission factor came from an older model passenger vehicle licensed in Baja California.     

Investigation of the motor vehicle exhaust contribution to primary fine particle organic carbon in urban air

Motor vehicle (MV) emissions and ambient particle concentrations under a variety of situations were studied in Toronto and Vancouver, Canada. Petroleum biomarkers (i.e., hopanes and steranes) were used to determine the fraction of fine particle organic carbon (OC) attributed to primary particles in MV exhaust. Source profiles obtained from a tunnel and from direct tailpipe emissions were applied to ambient measurements at locations ranging from rush hour traffic to a regional background site. The greatest amount of MV OC, 4.0 μgC m⁻³ out of 9.1 μgC m⁻³ or 43%, was observed 75 m south of a commuter highway during a period that included morning rush hour. Monthly estimates of MV-OC were determined for a downtown Toronto monitoring site for 2 years. Total OC concentrations were greater in the summer, due to secondary OC, but the amount of MV-OC did not exhibit a strong seasonal pattern. However, on a per cent basis, MV contributions from primary OC emissions were greatest in the winter (15–20%) and smallest in the summer (10–15%) with a two-year average of 14% of the OC or about 5% of the PM_2.5.     

Evolution of vehicle exhaust particles in the atmosphere

Aerosol mass spectrometer (AMS) measurements are used to characterize the evolution of exhaust particulate matter (PM) properties near and downwind of vehicle sources. The AMS provides time-resolved chemically speciated mass loadings and mass-weighted size distributions of nonrefractory PM smaller than 1 microm (NRPM1). Source measurements of aircraft PM show that black carbon particles inhibit nucleation by serving as condensation sinks for the volatile and semi-volatile exhaust gases. Real-world source measurements of ground vehicle PM are obtained by deploying an AMS aboard a mobile laboratory. Characteristic features of the exhaust PM chemical composition and size distribution are discussed. PM mass and number concentrations are used with above-background gas-phase carbon dioxide (CO2) concentrations to calculate on-road emission factors for individual vehicles. Highly variable ratios between particle number and mass concentrations are observed for individual vehicles. NRPM1 mass emission factors measured for on-road diesel vehicles are approximately 50% lower than those from dynamometer studies. Factor analysis of AMS data (FA-AMS) is applied for the first time to map variations in exhaust PM mass downwind of a highway. In this study, above-background vehicle PM concentrations are highest close to the highway and decrease by a factor of 2 by 200 m away from the highway. Comparison with the gas-phase CO2 concentrations indicates that these vehicle PM mass gradients are largely driven by dilution. Secondary aerosol species do not show a similar gradient in absolute mass concentrations; thus, their relative contribution to total ambient PM mass concentrations increases as a function of distance from the highway. FA-AMS of single particle and ensemble data at an urban receptor site shows that condensation of these secondary aerosol species onto vehicle exhaust particles results in spatial and temporal evolution of the size and composition of vehicle exhaust PM on urban and regional scales.     

A study of emissions from a Euro 4 light duty diesel vehicle with the European particulate measurement programme

The California Air Resources Board, CARB, has participated in a program to quantify particulate matter (PM) emissions with a European methodology, which is known as the Particulate Measurement Programme (PMP). The essence of the PMP methodology is that the diesel PM from a Euro 4 vehicle equipped with a Diesel Particulate Filter (DPF) consists primarily of solid particles with a size range greater than 23 nm. The PMP testing and the enhanced testing performed by CARB have enabled an increased understanding of both the progress that has been made in PM reduction, and the future remaining challenges for new and improved DPF-equipped diesel vehicles. A comparison of measured regulated emissions and solid particle number emissions with the results obtained by the PMP participating international laboratories was a success, and CARB’s measurements and standard deviations compared well with the other laboratories. Enhanced measurements of the influence of vehicle conditioning prior to testing on PM mass and solid particle number results were performed, and some significant influences were discovered. For example, the influence of vehicle preconditioning on particle number results was significant for both the European and USA test driving cycles. However, the trends for the cycles were opposite with one cycle showing an increase and the other cycle showing a decrease in particle number emissions. If solid particle size distribution and total particle numbers are to be used as proposed in PMP, then a greater understanding of the quality and errors associated with measurement technologies is advisable.In general, particle counting instruments gave results with similar trends, but cycle-to-cycle testing variation was observed. Continuous measurements of particle number concentrations during test cycles have given detailed insight into PM generation. At the present time there is significant variation in the capabilities of the particle counting instruments in terms of particle size and concentration.Current measurements show the existence of a large number of volatile and semi-volatile particles of yet-to-be-resolved chemical composition in diesel exhaust, especially during DPF regeneration, and these particles are not included in the PMP methodology because they are smaller than 20 nm. It will be very challenging to improve our understanding of this class of diesel particulate matter.