The estimation of PAH bioavailability in contaminated sediments using hydroxypropyl-beta-cyclodextrin and Triton X-100 extraction techniques

A study was conducted to investigate whether cyclodextrins and surfactants can be used to predict polycyclic aromatic hydrocarbon (PAH) bioavailability in contaminated sediments. Two sediment samples were extracted with aqueous solutions of hydroxypropyl-beta-cyclodextrin (HPCD) and Triton X-100. PAH removal during extraction was compared with PAH removal during biodegradation and solid-phase extraction. The latter two methods were used as reference methods to establish which part of the PAHs could be biodegraded and to what extent biodegradation was governed by bioavailability limitations. It was demonstrated that HPCD extraction followed solid-phase extraction and removed primarily readily bioavailable PAHs, while Triton X-100 extracted both readily and poorly bioavailable PAHs. Moreover, HPCD did not affect the degradation of PAHs in biodegradation experiments, while Triton X-100 enhanced the degradation of low molecular weight PAHs. It was concluded that HPCD extraction may provide a good method for the prediction of PAH bioavailability. Triton X-100 extraction is unfit for the prediction of PAH bioavailability.     

应用表面活性剂-生物柴油微乳液去除污染土壤中多环芳烃

针对修复焦化厂高浓度多环芳烃污染土壤高成本的现实,采用以非食用性植物油、生物柴油、表面活性剂及其乳化合成的微乳液为淋洗剂,比较不同淋洗剂的淋洗效果。结果表明乳化合成的微乳液对焦化厂土壤中多环芳烃的总去除率高于单独使用表面活性剂为淋洗剂对土壤中多环芳烃的总去除率,说明生物柴油及植物油与表面活性剂乳化形成的微乳液对原污染土壤中的多环芳烃具有显著的增溶作用。1%TW-80和2.5%TW-80对土壤中多环芳烃总去除率分别为11%和14%;以2.5%TW-80为原料乳化合成的微乳液的淋洗去除率较以1%TW-80为原料乳化合成的微乳液高,总去除率分别为15%～30%和11%～18%;以生物柴油为原料乳化合成的微乳液的淋洗去除率较以植物油为原料乳化合成的微乳液高,分别为17%～30%和15%～23%,且对多环芳烃的去除率与其辛醇水分配系数(logKow)呈线性相关关系。     

Removal of polycyclic aromatic hydrocarbons from manufactured gas plant-contaminated soils using sunflower oil: laboratory column experiments

Laboratory column experiments were performed to remove PAHs (polycyclic aromatic hydrocarbons) from two contaminated soils using sunflower oil. Two liters of sunflower oil was added to the top of the columns (33 cm x 21 cm) packed with 1 kg of PAH-contaminated soil. The sunflower oil was applied sequentially in two different ways, i.e. five additions of 400 ml or two additions of 1l. The influence of PAH concentration and the volume of sunflower oil on PAH removal were examined. A soil respiration experiment was carried out and organic carbon contents of the soils were measured to determine degradability of remaining sunflower oil in the soils. Results showed that the sunflower oil was effective in removing PAHs from the two soils, more PAHs were removed by adding sunflower oil in two steps than in five steps, probably because of the slower flow rate in the former method. More than 90% of total PAHs was removed from a heavily contaminated soil (with a total 13 PAH concentration of 4721 mg kg(-1)) using 4 l of sunflower oil. A similar removal efficiency was obtained for another contaminated soil (with a total 13 PAH concentration of 724 mg kg(-1)), while only 2l was needed to give a similar efficiency. Approximately 4-5% of the sunflower oil remained in the soils. Soil respiration curves showed that remaining sunflower oil was degraded by allowing air exchange and supplying with nutrients. Organic carbon content of the soil was restored to original level after 180 d incubation. These results indicated that the sunflower oil had a great capacity to remove PAHs from contaminated soils, and sunflower oil solubilization can be an alternative technique for remediation of PAH contaminated soils.     

Removal of polycyclic aromatic hydrocarbons from aged-contaminated soil using cyclodextrins: experimental study

The removal of polycyclic aromatic hydrocarbons (PAHs) from soil using water as flushing agent is relatively ineffective due to their low aqueous solubility. However, addition of cyclodextrin (CD) in washing solutions has been shown to increase the removal efficiency several times. Herein are investigated the effectiveness of cyclodextrin to remove PAH occurring in industrially aged-contaminated soil. Beta-cyclodextrin (BCD), hydroxypropyl-beta-cyclodextrin (HPCD) and methyl-beta-cyclodextrin (MCD) solutions were used for soil flushing in column test to evaluate some influent parameters that can significantly increase the removal efficiency. The process parameters chosen were CD concentration, ratio of washing solution volume to soil weight, and temperature of washing solution. These parameters were found to have a significant and almost linear effect on PAH removal from the contaminated soil, except the temperature where no significant enhancement in PAH extraction was observed for temperature range from 5 to 35 degrees C. The PAHs extraction enhancement factor compared to water was about 200.     

Dissolution and removal of PAHs from a contaminated soil using sunflower oil

This study reports on the feasibility of remediation of polycyclic aromatic hydrocarbon (PAH) contaminated soils using sunflower oil, an environmentally-friendly solvent. Batch experiments were performed to test the influence of oil/soil ratio on the remediation of PAH contaminated soil, and to test the mass transfer behaviors of PAHs from soil to oil. An empirical model was employed to describe the kinetics of PAH dissolution and to predict equilibrium concentrations of PAHs in oil. PAH containing oil was regenerated using active carbon. Results show that dissolution of PAHs from a Manufactured Gas Plant (MGP) soil at oil/soil ratios of one or two were almost the same. Nearly all PAHs (81-100%) could be removed by sunflower oil dissolution. Mass transfer coefficients for low molecular PAHs namely fluoranthene, phenanthrene and anthracene were one or two orders of magnitude higher than those for high molecular PAHs with 4-6 rings. Ninety milliliters of PAH containing oil could be regenerated by 10 g active carbon in a batch reactor. Such a remediation procedure indicates that sunflower oil is a promising agent for the removal of PAHs from MGP soils. However, further research is required before the method can be used for in situ remediation of contaminated sites.     

Distribution of polycyclic aromatic hydrocarbons in soil-water system containing a nonionic surfactant

The effect of a nonionic surfactant, Triton X-100 (TX100), on the distribution of four representative polycyclic aromatic hydrocarbons (PAHs), phenanthrene, fluorene, acenaphthene and naphthalene, in soil-water system was studied on a natural soil. The apparent soil-water distribution coefficient with surfactant (Kd*) for these compounds increased when TX100 equilibrium concentration from zero to around the critical micelle concentration (CMC), followed by a decrease in Kd* at TX100 equilibrium concentration greater than CMC. This is a direct result of surfactant sorption onto soil followed by PAHs partitioning to the sorbed surfactant. The values of carbon-normalized solute distribution coefficient (Kss) with the sorbed TX100 are greater than the corresponding partition coefficients with soil organic matter (Koc), which indicates the soil-sorbed nonionic surfactant is more effective per unit mass as a partitioning medium than the native soil organic matter for PAHs. When Kd* = Kd the corresponding initial concentration of surfactant was defined as critical washing concentration (CWC). Depending on the surfactant initial concentration below or above the CWC, the addition of nonionic surfactant can enhance the retardation of soil for PAHs or promote the removal of PAHs from soil, respectively. The values of Kd* and CWC can be predicted by a model, which correlates them with the compounds' octanol-water partition coefficients (Kow), soil property and the amount of soil-sorbed surfactant.     

Remediation of polycyclic aromatic hydrocarbon and metal-contaminated soil by successive methyl-β-cyclodextrin-enhanced soil washing–microbial augmentation: a laboratory evaluation

Polycyclic aromatic hydrocarbon (PAH) and metal-polluted sites caused by abandoned coking plants are receiving wide attention. To address the associated environmental concerns, innovative remediation technologies are urgently needed. This study was initiated to investigate the feasibility of a cleanup strategy that employed an initial phase, using methyl-β-cyclodextrin (MCD) solution to enhance ex situ soil washing for extracting PAHs and metals simultaneously, followed by the addition of PAH-degrading bacteria (Paracoccus sp. strain HPD-2) and supplemental nutrients to treat the residual soil-bound PAHs. Elevated temperature (50 °C) in combination with ultrasonication (35 kHz, 30 min) at 100 g MCD L^?1 was effective in extracting PAHs and metals to assist soil washing; 93 % of total PAHs, 72 % of Cd, 78 % of Ni, 93 % of Zn, 84 % of Cr, and 68 % of Pb were removed from soil after three successive washing cycles. Treating the residual soil-bound PAHs for 20 weeks led to maximum biodegradation rates of 34, 45, 36, and 32 % of the remaining total PAHs, 3-ring PAHs, 4-ring PAHs, and 5(+6)-ring PAHs after washing procedure, respectively. Based on BIOLOG Ecoplate assay, the combined treatment at least partially restored microbiological functions in the contaminated soil. The ex situ cleanup strategy through MCD-enhanced soil washing followed by microbial augmentation can be effective in remediating PAH and metal-contaminated soil.     

蓖麻油衍生微乳液对菲的增溶和洗脱作用及其对菲污染土壤的修复机理

比较研究了蓖麻油硫酸盐(SCOS)与普通表面活性剂Triton X-100(TX100)、Tween 80(TW80)、Brij35、十二烷基苯磺酸钠(SDBS)和十二烷基硫酸钠(SDS)等对菲的增溶和洗脱作用.结果表明,菲表观溶解度与SCOS的浓度呈单一线性关系,SCOS微乳液对菲的增溶比SR=0.0314为最大,菲在微乳相和水相之间的分配系数logKem=4.44,大于菲在胶束相和水相之间的分配系数(logKmc).1:10土-水体系下,SCOS微乳液对菲污染土壤的清洗速率最快,清洗效率最高.SCOS有望成为土壤有机污染淋洗修复的增效试剂.     

PAH removal from spiked municipal wastewater sewage sludge using biological, chemical and electrochemical treatments

Polycyclic aromatic hydrocarbons (PAHs) have been widely studied due to their presence in all the environmental media and toxicity to life. These molecules are strongly adsorbed on the particulate matters of soils, sludges or sediments because of their strong hydrophobicity which makes them less bioavailability, thus limiting their bioremediation. Different sludge treatment processes were tested to evaluate their performances for PAH removal from sludge prealably doped with 11 PAHs (5.5mg each PAH kg(-1) of dry matter (DM)): two biological processes (mesophilic aerobic digestion (MAD) and simultaneous sewage sludge digestion and metal leaching (METIX-BS)) were tested to evaluate PAH biodegradation in sewage sludge. In parallel, two chemical processes (quite similar Fenton processes: chemical metal leaching (METIX-AC) and chemical stabilization (STABIOX)) and one electrochemical process (electrochemical stabilization (ELECSTAB)) were tested to measure PAH removal by these oxidative processes. Moreover, PAH solubilisation from sludge by addition of a nonionic surfactant Tween 80 (Tw80) was also tested. The best yields of PAH removal were obtained by MAD and METIX-BS with more than 95% 3-ring PAH removal after a 21-day treatment period. Tw80 addition during MAD treatment increased 4-ring PAHs removal rate. In addition, more than 45% of 3-ring PAHs were removed from sludge by METIX-AC and during ELECSTAB process were quiet good with approximately 62% of 3-ring PAHs removal. However, little weaker removal of 3-ring PAHs (<35%) by STABIOX. None of the tested processes were efficient for the elimination of high molecular weight (> or = 5-ring) PAHs from sludge.     

Migration of polycyclic aromatic hydrocarbons (PAHs) in urban treatment sludge to the air during PAH removal applications

In the present study, the amounts of polycylic aromatic hydrocarbons (PAHs) penetrating into air during PAH removal applications from the urban treatment sludge were investigated. The effects of the temperature, photocatalyst type, and dose on the PAH removal efficiencies and PAH evaporation were explained. The sludge samples were taken from an urban wastewater treatment plant located in the city of Bursa, with 585,000 equivalent population. The ultraviolet C (UV-C) light of 254 nm wavelength was used within the UV applications performed on a specially designed setup. Internal air of the setup was vacuumed through polyurethane foam (PUF) columns in order to collect the evaporated PAHs from the sludge during the PAH removal applications. All experiments were performed with three repetitions. The PAH concentrations were measured by gas chromatography–mass spectrometry (GC-MS). It was observed that the amounts of PAHs penetrating into the air were increased with increase of temperature, and more than 80% of PAHs migrated to the air consisted of 3-ring compounds during the UV and UV-diethylamine (DEA) experiments at 38 and 53 °C. It was determined that 40% decrease was ensured in Σ₁₂ (total of 12) PAH amounts with UV application and 13% of PAHs in sludge penetrated into the air. In the UV-TiO₂ applications, a maximum 80% of Σ₁₂ PAH removal was obtained by adding 0.5% TiO₂ of dry weight of sludge. The quantity of PAH penetrating into air did not exceed 15%. UV-TiO₂ applications ensured high levels of PAH removal in the sludge and also reduced the quantity of PAH penetrating into the air. Within the scope of the samples added with DEA, there was no increase in PAH removal efficiencies and the penetration of PAHs into air was not decreased. In light of these data, it was concluded that UV-TiO₂ application is the most suitable PAH removal alternative that restricts the convection of PAH pollution.

Implications: Polycyclic aromatic hydrocarbon (PAH) evaporation rates from sludge samples obtained from an urban wastewater treatment plant were investigated here for the first time by employing removal applications. TiO₂ and diethylamine were used as photocatalysts in this study. A special device was designed and successfully used in this study. Treatment sludge can be a significant source of PAHs for the atmosphere. The data highlight the need for removal of PAHs in treatment sludge via methods limiting their evaporation to the air. It was observed that UV-TiO₂ application was the most suitable PAH removal alternative that restricts the convection of PAH pollution.     

A comparative study of adsorption of an anionic and a non-ionic surfactant by soils based on physicochemical and mineralogical properties of soils

In the present work we performed a comparative study on the adsorption of the surfactants sodium dodecyl sulphate (SDS) (anionic), and octylphenoxypolyethoxyethanol (Triton X-100) (non-ionic) to 18 soils with organic matter (OM) and clay fraction contents varying over a broad range. The objective of the study was to gain further insight into the influence of the physicochemical and mineralogical properties of soils on the adsorption of surfactants by soils. Adsorption isotherms were obtained using concentrations below the critical micellar concentration (cmc) of the surfactants. The adsorption coefficients, Kf, determined from the Freundlich equation were lower for SDS (range 1.77-82.1, mean value 36.3) than for Triton X-100 (range 0.01-913, mean value 257). Simple and multiple correlation coefficients were obtained between Kf values and soil characteristics. The results obtained indicate the influence of the OM content on the adsorption of SDS (r=0.64, p<0.01) and of the clay fraction content on that of Triton X-100 (r=0.83, p<0.001). Additionally, we observed a preferential adsorption of SDS by the 1:1 mineral kaolinite (r=0.54, p<0.05), while Triton X-100 was adsorbed mainly by the 2:1 minerals, montmorillonite (r=0.66, p<0.01) and illite (r=0.87, p<0.001). According to the influence of different soil parameters on adsorption, different mechanisms of adsorption are proposed for each surfactant. Our findings point to the interest of considering the physicochemical properties of soils and also the mineralogy of the soil clay fraction when selecting a surfactant in technologies involving enhanced solubilization and removal of contaminants from soils and sediments.     

Passive samplers versus surfactant extraction for the evaluation of PAH availability in sediments with variable levels of contamination

The purpose of this study was to test the efficiency of passive solid samplers, polyoxymethylene (POM) strips and polydimethylsiloxane (PDMS) silicon tubing, to predict the bioavailability of native PAHs in contaminated sediments. Results were compared with worm bioaccumulation data and solid/liquid extraction using the surfactant Brij((R)) 700 (B700). The two passive samplers were found to act differently. The PDMS sampler overestimated the availability of PAHs in all studied sediments. The POM method provided results in accordance with those obtained with the B700 extraction. However, POM and B700 methods underestimated PAH availability in low contaminated sediments where biological factors (digestible organic matter) become important. Bioavailability of total PAHs was correctly predicted by POM and B700 in highly contaminated aluminum smelter sediments. A closer examination of individual PAH results indicated that both techniques overestimated the availability of large molecules with logK(ow)>6 suggesting a biological mechanism limiting uptake of larger PAHs which seems to be related to the molecular size of compounds.     

Effects of pig manure compost and nonionic-surfactant Tween 80 on phenanthrene and pyrene removal from soil vegetated with Agropyron elongatum

This paper evaluates the effects of pig manure compost (PMC) and Tween 80 on the removal of phenanthrene (PHE) and pyrene (PYR) from soil cultivated with Agropyron elongatum. Soils spiked with about 300mgkg(-1) of PHE and PYR were individually amended with 0%, 2.5%, 5% and 7.5% (dry wt) of PMC or 0, 20 and 100mgkg(-1) of Tween 80. Unplanted and sterile microcosms were prepared as the controls. PAH concentration, total organic matter (TOM), dissolved organic carbon (DOC), total heterotrophic and PAH degrading microbial populations in soil were quantified before and after 60d period. The results indicated that A. elongatum could significantly enhance PYR removal (from 46% to 61%) but had less impact on PHE removal (from 96% to 97%). Plant uptake of the PAHs was insignificant. Biodegradation was the key mechanism of PAH removals (<3% losses in the sterile control). Increase in PMC or Tween 80 levels increased the removal of PYR but not of PHE. Maximal PYR removal of 79% and 92% were observed in vegetated soil receiving 100mgkg(-1) Tween 80 and 7.5% PMC, respectively. Enhanced PYR removal in soil receiving PMC could be explained by the elevated levels of DOC, TOM and microbial populations as suggested by Pearson correlation test. While the positive effect of Tween 80 on PYR removal could probably due to its capacities to enhance PYR bioavailability in soil. This paper suggests that the addition of either PMC or nonionic-surfactant Tween 80 could facilitate phytoremediation of PAH contaminated soil.     

Treatment of PAHs in contaminated soil by extraction with aqueous DNA followed by biodegradation with a pure culture of Sphingomonas sp

The biodegradation of polycyclic aromatic hydrocarbons (PAHs) in aqueous deoxyribonucleic acid (DNA) solution from contaminated soil washing was investigated. Initial data with a model effluent consisting of anthracene, phenanthrene, pyrene and benzo[a]pyrene that were individually dissolved in 1% aqueous DNA solution confirmed their positive degradation by Sphingomonas sp. at around 10(8)CFU mL(-1) initial cell loading. For anthracene and phenanthrene, complete removal was achieved within 1h treatment. Degradation of pyrene and benzo[a]pyrene took a relatively longer time of a few days and weeks, respectively. DNA-dissolved PAHs were also degraded relatively faster than PAH crystals in aqueous medium to suggest that the binding of the PAHs in the polymer does not pose serious constraint to bacterial uptake. The DNA was stable against the PAH-degrading bacteria. Parallel experiments with actual DNA solutions obtained during pyrene extraction from an artificially spiked soil also showed similar results. Close to 100% pyrene degradation was achieved after 1d treatment. With its chemical stability, the cell-treated DNA was re-used up to four cycles without a considerable decline in extraction performance.     

Selective adsorption of phenanthrene dissolved in surfactant solution using activated carbon

Selective adsorption of a hazardous hydrophobic organic compound (HOC) by activated carbon as a means of recovering surfactants after a soil washing process was investigated. As a model system, phenanthrene was selected as a representative HOC and Triton X-100 as a nonionic surfactant. Three activated carbons that differed in size (Darco 20–40 (D20), 12–20 (D12) and 4–12 (D4) mesh sizes) were used in adsorption experiments. Adsorption of surfactant onto activated carbon showed a constant maximum above the critical micelle concentration, which were 0.30, 0.23, 0.15 g g⁻¹ for D20, D12, and D4, respectively. Selectivity for phenanthrene to Triton X-100 was much higher than 1 over a wide range of activated carbon doses (0–6 g l⁻¹) and initial phenanthrene concentrations (10–110 mg l⁻¹). Selectivity generally increased with decreasing particle size, increasing activated carbon dose, and decreasing initial concentration of phenanthrene. The highest selectivity was 74.9, 57.3, and 38.3 for D20, D12, and D4, respectively, at the initial conditions of 10 mg l⁻¹ phenanthrene, 5 g l⁻¹ Triton X-100 and 1 g l⁻¹ activated carbon. In the case of D20 at the same conditions, 86.5% of the initial phenanthrene was removed by sorption and 93.6% of the initial Triton X-100 remained in the solution following the selective adsorption process. The results suggest that the selective adsorption by activated carbon is a good alternative for surfactant recovery in a soil washing process.     

Evaluation of biosurfactants for crude oil contaminated soil washing

An evaluation of the ability of aqueous biosurfactant solutions (aescin, lecithin, rhamnolipid, saponin and tannin) for possible applications in washing crude oil contaminated soil was carried out. The biosurfactants behaviour in soil-water, water-oil and oil-soil systems (such as foaming, solubilization, sorption to soil, emulsification, surface and interfacial tension) was measured and compared with a well-known chemical surfactant (sodium dodecyl sulphate, SDS) at varying concentrations. Results showed that the biosurfactants were able to remove significant amount of crude oil from the contaminated soil at different solution concentrations for instance rhamnolipid and SDS removed up to 80% oil and lecithin about 42%. The performance of water alone in crude oil removal was equally as good as those of the other biosurfactants. Oil removal was due to mobilization, caused by the reduction of surface and interfacial tensions. Solubilization and emulsification effects in oil removal were negligible due to the low crude oil solubilization of 0.11%. Therefore, these studies suggest that knowledge of surfactants' behaviour across different systems is paramount before their use in the practical application of oil removal.     

Removal of PAHs with surfactant-enhanced soil washing: influencing factors and removal effectiveness

PAH removal with surfactant enhanced washing was investigated through a series of laboratory tests to examine the effect of stirring speed, washing time, surfactant concentration, liquid/solid ratio, temperature, and on-and-off mode. The first four factors show significant influence on the PAH removal while the latter two do not. Total removal ratio and a new proposed parameter, solubilization percentage, are used to evaluate the effectiveness quantitatively.     

工艺参数对表面活性剂洗涤修复PAHs污染土壤的影响

采用土壤洗涤(soil-washing)技术,分别用TritonX-100和Tween-80为强化洗涤剂研究了搅拌强度、洗涤时间、表面活性剂浓度、液固比、温度和间歇搅拌6个工艺参数对PAHs污染土壤洗涤效果的影响。通过一系列烧杯搅拌实验得到最佳洗涤工艺参数。TritonX-100和Tween-80的最佳洗涤时间分别是30 min和60 min,其他工艺参数最佳条件均相同。分别是搅拌强度为250 r/min,表面活性剂浓度为5 g/L,液固比为10∶1,温度为室温和连续搅拌。在此最佳工艺参数条件下,污染土中PAHs的残留率<10%,基本上满足目标污染物的修复目标。应用表面活性剂强化洗涤技术修复PAHs污染土壤是合理和可行的。     

Influence of mature compost amendment on total and bioavailable polycyclic aromatic hydrocarbons in contaminated soils

A laboratory microcosm study was carried out to assess the influence of compost amendment on the degradation and bioavailability of PAHs in contaminated soils. Three soils, contaminated with diesel, coal ash and coal tar, respectively, were amended with two composts made from contrasting feedstock (green waste and predominantly meat waste) at two different rates (250 and 750 t ha^?1) and incubated for 8 months. During this period the treatments were sampled for PAH analysis after 0, 3, 6 and 8 months. Total and bioavailable fractions were obtained by sequential ultrasonic solvent extraction and hydroxypropyl-β-cyclodextrin extraction, respectively, and PAHs were identified and quantified by GC–MS. Bioavailability decrease due to sorption was only observed at the first 3 months in the diesel spiked soil. After 8 months, compost addition resulted in over 90% loss of total PAHs irrespective of soil types. Desorption and degradation contributed to 30% and 70%, respectively, of the PAH loss in the spiked soil, while PAH loss in the other two soils resulted from 40% enhanced desorption and 60% enhanced degradation. Compost type and application rates had little influence on PAH bioavailability, but higher PAH removal was observed at higher initial concentration during the early stage of incubation. The bioavailable fraction of PAH was inversely correlated to the number of benzene rings and the octanol–water partition coefficient. Further degradation was not likely after 8-month although over 30% of the residual PAHs were bioavailable, which highlighted the application of bioavailability concept during remediation activities.     

EPA SITE Demonstration of the BioTrol Soil Washing Process

A pilot-scale soil washing process, patented by BioTrol, Inc., was demonstrated on soil contaminated by wood treating waste, primarily pentachlorophenol (PCP) and creosote-derived polynuclear aromatic hydrocarbons (PAHs). Although soil washing was the main object of this demonstration, the treatment train that was evaluated included two other BioTrol technologies for treatment of waste streams from the soil washer. The three technologies were: ? The BioTrol Soil Washer (BSW)—a volume reduction process, which uses water to separate contaminated soil fractions from the bulk of the soil.

? The BioTrol Aqueous Treatment System (BATS)—a biological water treatment process.

? The Slurry Bioreactor (SBR)—a BioTrol biological slurry treatment process conducted in an EIMCO BIOLIFT^tm reactor.

The sandy soil at the site, consisting of less than 10 percent of fines, was well suited for treatment by soil washing. The soil washer was evaluated in two tests on soil samples containing 130 ppm and 680 ppm of PCP, respectively.

The BSW successfully separated the feed soil (dry weight basis) into 83 percent of washed soil, 10 percent of woody residues, and 7 percent of fines. The washed soil retained about 10 percent of the feed soil contamination while 90 percent of the feed soil contamination was contained within the woody residues, fines, and process water.

The soil washer achieved up to 89 percent removal of PCP and 88 percent of total PAHs, based on the difference between their levels in the as-is (wet) feed soil and the washed soil. PCP concentrations of 14 ppm and 87ppm in the washed soil were achieved from PCP concentrations of 130 ppm and 680ppm in the feed soil. Concentrations of total PAHs were reduced from 247 ppm to 42 ppm and 404 ppm to 48 ppm, respectively, in the two tests.

The BATS degraded up to 94 percent of PCP in the process water from soil washing. PAH removal could not be determined due to low influent concentrations.

The SBR achieved over 90 percent removals of PCP and 70 to 90 percent removals of PAHs from the slurry of contaminated fines from soil washing. However, steady state operation was not achieved during the single test and the results were variable.

Cost of a commercial-scale soil washing, assuming use of all three technologies, was estimated to be $168 per ton of soil treated. Incineration of woody material accounts for 76 percent of the cost.