Air Levels and Mutagenicity of PM-10 in an Indoor Ice Arena

Abstract

Hazardous waste sites and industrial facilities contain area sources of fugitive emissions. Emission rate measurements or estimates are necessary for air pathway assessments for these sources. Emission rate data can be useful for the design of emission control and remediation strategies as well as for predictive modeling for population exposure assessments. This paper describes the use of a direct emission measurement approach – the enclosure approach using an emission isolation flux chamber – to measure emission rates of various volatile organic compounds (VOCs) from contaminated soil and water. A variety of flux chamber equipment designs and operating procedures have been employed by various researchers. This paper contains a review of the design and operational variables that affect the accuracy and precision of the method. Guidance is given as to the optimum flux chamber design and operating conditions for various types of emission sources. Also presented is a generic quality control program that gives the minimum number of duplicate, blank, background, and repeat samples that should be performed.     

Characterization of Air Quality Problems in Five Finnish Indoor Ice Arenas

ABSTRACT

The air quality in five Finnish ice arenas with different volumes, ventilation systems, and resurfacer power sources (propane, gasoline, electric) was monitored during a usual training evening and a standardized, simulated ice hockey game. The measurements included continuous recording of carbon monoxide (CO), nitric oxide (NO), and nitrogen dioxide (NO₂) concentrations, and sampling and analysis of volatile organic compounds (VOCs). Emissions from the ice resurfacers with combustion engines caused indoor air quality problems in all ice arenas. The highest 1-hour average CO and NO₂ concentrations ranged from 20 to 33 mg/m³ (17 to 29 ppm) and 270 to 7440 µg/m³ (0.14 to 3.96 ppm), respectively. The 3-hour total VOC concentrations ranged from 150 to 1200 µg/m³. The highest CO and VOC levels were measured in the arena in which a gasoline-fueled resurfacer was used. The highest NO₂ levels were measured in small ice arenas with propane-fueled ice resurfacers and insufficient ventilation.

In these arenas, the indoor NO₂ levels were about 100 times the levels measured in ambient outdoor air, and the highest 1-hour concentrations were about 20 times the national and World Health Organization (WHO) health-based air quality guidelines. The air quality was fully acceptable only in the arena with an electric resurfacer. The present study showed that the air quality problems of indoor ice arenas may vary with the fuel type of resurfacer and the volume and ventilation of arena building. It also confirmed that there are severe air quality problems in Finnish ice arenas similar to those previously described in North America.     

Ambient Air Quality and Automotive Emission Control

This paper is concerned with uncertainties involved in projecting ambient air quality. Ambient air quality was projected by assuming a linear dependence on estimated future emissions. Future automotive emissions were estimated by a method recommended by EPA. Projections were made for the locations reported to have the highest ambient air concentrations of each pollutant; Chicago for carbon monoxide and the California South Coast Air Basin for hydrocarbon and oxidant. The sensitivity of the projections to several input parameters was determined.

The uncertainty in projection of air quality due to the use of a maximum, once-per-year concentration is large. For example, the reduction in total CO emissions in Chicago in 1975, necessary to meet the air quality standard, was as high as 68% or as low as 26%, depending on whether the historic high, 8 hr average concentration of 44 ppm or the 1970 maximum of 21 ppm was used. The effects of uncertainties in growth rates and fraction of emissions attributed to the automobile were also sizeable. Differences in automotive growth rate had a large near-term effect on projected concentrations, while differences in nonautomotive growth rate or fraction of emissions attributed to the automobile had a large long-term effect. The effect of 1975 interim automotive emission standards on projected air quality was negligible when compared with projected air quality based on the previous Federal automotive emission standards for 1975.     

A Study of Indoor Air Quality

As part of a larger program to investigate indoor sources of air pollution, an indoor/outdoor sampling program was carried out for NO, NO₂, and CO In four private houses which had gas stoves. The four houses chosen for study represented different surrounding land use, life styles, and house age and layout. The pollutant gases were measured essentially simultaneously at three indoor locations and one outdoor location. The results of the program showed that indoor levels of NO and NO₂ are directly related to stove use in the homes tested. Furthermore, these stoves often produced more NO₂ than NO. In some instances, the levels of NO₂ and CO in the kitchen exceeded the air quality standards for these pollutants if such outdoor standards were to be applied to indoors and the data for the sampling periods were typical of an entire year. A diffusion experiment conducted in one of the houses showed that the half-life for NO₂ was less than one-third that for either NO or CO. Oxidation of NO to NO₂ (based upon comparing the half-life of NO to CO) does not appear to occur to a significant degree indoors.     

室内空气污染的生物监测与生物防治

介绍了室内空气污染的来源及其危害,采用常见花木来监测室内的空气污染,并可用常见盆栽植物来防治室内的空气污染.     

室内空气污染分析及防治措施

简述了室内空气污染的种类和特点，多角度论述了室内空气污染的防治措施。     

Air Quality Management in Los Angeles: Perspectives on Past and Future Emission Control Strategies

The 1988 Air Quality Management Plan was approved by the Board of the California South Coast Air Quality Management District in March 1989. The District comprises the counties of Los Angeles, Orange, and Riverside, and the non-desert portion of San Bernardino county. Emissions reductions in the past have lead to significant improvement in air quality despite large increases in growth. However, the District, largely because of continuous growth, currently violates the air quality standards for ozone, carbon monoxide, nitrogen dioxide, and respirable particulate matter (PM₁₀). Based upon the AQMP, reduction of approximately 80 percent in emissions of oxides of nitrogen and volatile organic compounds is required to bring the District into compliance with all air quality standards in the next twenty years.

Achieving compliance will necessitate the use of advanced technologies, as well as some changes in lifestyle and management practices. Advanced technologies, including the use of electric vehicles powered by batteries or fuel cells, the use of cleaner burning fuels and advanced combustion modifications, and treatment of surface coatings and solvents are included in the AQMP. The Technology Advancement Office in the District was created to work with industry, universities, research institutes, and other local, state and federal agencies to identify, evaluate, and promote low emitting fuels and technologies. In addition to electricity, fuels burning cleaner than conventional gasoline or diesel are being tested to obtain emissions and durability data so that rational choices can be made for the future. Compressed natural gas, methanol and liquefied petroleum gas are considered to be cleaner burning fuels for current applications. Ethanol, butane, and various oxygenated blends are being evaluated, and the broader application of solar energy and hydrogen are being investigated.

The impact of various cleaner burning fuels on air quality is being addressed. To date, methanol is the only fuel for which results are available. These results indicate that methanol use in vehicles—with control of formaldehyde emissions below 15 mg/mile for light-duty vehicles—can provide air quality benefits for all criteria pollutants and certain air toxics. These benefits are greater for M₁₀₀ than M₈₅.

Several District advanced technology programs are described, including a reduction in emissions from paints and coatings, and the demonstration of electric vehicles.     

江苏省污染减排与空气质量变化相关性分析

利用2000—2007年大气污染物排放量数据和同期环境空气质量监测数据,分析了江苏省主要大气污染物减排与环境空气质量变化的相关性。结果表明,近年来江苏省SO2排放量与环境空气中SO2浓度存在正相关,而烟尘和粉尘排放总量与空气中可吸入颗粒物的浓度呈现出弱的负相关关系。对江苏省经济发展和环境关系的进一步分析揭示,江苏省环境库兹涅茨曲线呈现出倒U型关系,表明江苏省已经进入经济环境双赢区间,但近年来政策对经济环境关系的影响突出。该研究对中国十二五环境管理政策的制定有着重要的参考意义。     

Numerical Evaluation of the Effect of Traffic Pollution on Indoor Air Quality of a Naturally Ventilated Building

Abstract

A computational fluid dynamics technique was used to evaluate the effect of traffic pollution on indoor air quality of a naturally ventilated building for various ventilation control strategies. The transport of street-level nonreactive pollutants emitted from motor vehicles through the indoor environment was simulated using the large eddy simulation (LES) of the turbulent flows and the pollutant transport equations. The numerical model developed herein was verified by available wind-tunnel measurements. Good agreement with the measured velocity and concentration data was found. Twelve sets of numerical scenario simulations for various roof- and side-vent openness and outdoor wind speeds were carried out. The effects of the air change rate, the indoor airflow pattern, and the external pollutant dispersion on indoor air quality were investigated. The control strategies of ventilation rates and paths for reducing incoming vehicle pollutants and maintaining a desirable air change rate are proposed to reduce the impact of outdoor traffic pollution during traffic rush hours. It was concluded that the windward side vent is a significant factor contributing to air change rate and indoor air quality. Air intakes on the leeward side of the building can effectively reduce the peak and average indoor concentration of traffic pollutants, but the corresponding air change rate is relatively low. Using the leeward cross-flow ventilation with the windward roof vent can effectively lower incoming vehicle pollutants and maintain a desirable air change rate during traffic rush hours.     

Removal of Small Particles from Air by Foam in a Sieve-Plate Column

Particle collection by foam produced on sieve plate apparatus was studied in a 3 x 3 in. sq column and in a 2 in. diam circular column. Experimental data have been obtained for silica test dust, glass beads, sulfur aerosol, polystyrene beads, and extensively for methylene blue aerosol. A new technique utilizing the Goetz aerosol spectrometer was developed and was used to obtain the collection efficiency as a function of particle diameter. A correlation was developed based on inertial mechanism. In this correlation the collection efficiency is expressed as a function of inertial parameter and foam density. The pressure drop in the operating range varied from 2 to 4 in. of water.     

The distribution of chlorpyrifos following a crack and crevice type application in the US EPA Indoor Air Quality Research House

A study was conducted in the US EPA Indoor Air Quality (IAQ) Research House to determine the spatial and temporal distribution of chlorpyrifos following a professional crack and crevice application in the kitchen. Following the application, measurements were made in the kitchen, den and master bedroom over 21 days. Airborne concentrations were collected using both polyurethane foam (PUF) and the OSHA versatile sampler composed of XAD and PUF media located in tandem. Measured airborne concentrations were similar for the two samplers and were higher in the three rooms following the application. The highest measured concentrations were reached during the initial 24-h following application; concentrations subsequently declined over the 21-day study period to levels slightly above background. Spatial and temporal distributions onto surfaces were measured using 10-cm² rayon deposition coupons located on the floor. Sections were cut from existing carpet to determine the total extractable residues. Chlorpyrifos was measured from all matrixes in the kitchen, den and bedroom and the data shows the transport of airborne residues from the point of application to remote locations in the house. The findings are compared and discussed relative to another study conducted in which total release aerosols containing chlorpyrifos were activated in the IAQ research house and the resulting distributions evaluated. For both studies dose estimates were constructed for the exposure pathways using the Stochastic Human Exposure and Dose Estimation Model for pesticides.The United States Environmental Protection Agency has been mandated to examine children's exposure to environmental pollutants such as pesticides. This research specifically reduces uncertainties associated with estimating children's potential exposures to residentially applied pesticides and provides inputs to further evaluate and validate residential exposure models which might be used to reduce exposures and perform risk assessments.     

Emissions Control and Ambient Air Quality at a Secondary Steel Production Facility

Steel production from electric arc furnaces has been continuously rising over the past few years. The trend is expected to continue due to both the anticipated increase in demand for steel, and to the replacement of obsolete open hearth furnaces. In 1972 steel produced in electric arc furnaces, which makes up 25 to 30% of the annual United States steel production, was produced primarily from recycled scrap steel in approximately 300 electric arc furnaces operated by 99 companies at 121 locations.¹ Over half of these furnaces are smaller than 50 tons, and many are located in small bar mills producing a variety of merchant steel products.     

远程控制软件pcAnywhere在空气质量监测系统中的应用

介绍了一款应用于空气质量监测系统中的优秀远程控制软件pcAnywhere,并具体说明了配置pcAnywhere对实现空气质量监测子站的管理与技术维护.     

Evaluation of Episode Control Schemes Through Air Quality Data Analysis

Prediction performance of various air pollution episode models are first compared with that of a persistence model which is based on the assumption that present concentrations persist to a future time. The comparisons are made by computing a correlation coefficient for different lead times between the observed and predicted values, and an auto-correlation function of the air quality data to which the episode model is applied. The persistence of high levels of air pollution is next examined, using existing air quality data, by constructing frequency distributions of air pollution episode duration for various concentration thresholds. Based on the results of persistence analysis, the flaws of currently used episode management schemes are discussed and some alternative episode management schemes are presented. Methodologies and parameters to evaluate the anticipated performances of episode management schemes are developed and some examples are worked out. In conclusion, it is suggested that a combination of episode persistence analysis and air pollution meteorological forecasting could lead to a workable air pollution episode management scheme.     

Particle Concentrations Inside a Tavern Before and After Prohibition of Smoking: Evaluating the Performance of an Indoor Air Quality Model

Abstract

Measurements were made of respirable suspended particles (RSP) in a large sports tavern on 26 dates over approximately two years in which smoking was allowed, followed by measurements on 50 dates during the year after smoking was prohibited. The smoking prohibition occurred without warning when the city government passed a regulation restricting smoking in local restaurants and taverns. Two follow-up field surveys, consisting of 24 and 26 visits, respectively, were conducted to measure changes in RSP levels after smoking was prohibited. No decrease in tavern attendance was evident after smoking was prohibited. During the smoking period, the average RSP concentration was 56.8 |ig/m3 above the outdoor concentrations, but the average abruptly dropped to 5.9 ug/m3 above outdoor levels—a 90% decrease— on 24 visits in the first two months immediately after smoking was prohibited (first follow-up study). A second set of 26 follow-up visits (matched by time of day, day of the week, and season to the earlier smoking visits) yielded an average concentration of 12.9 jig/m3 above the outdoor levels, or an overall decrease in the average RSP concentration of 77% compared with the smoking period. During the smoking period, RSP concentrations more than 100 ug/m3 above outdoor levels occurred on 30.7% of the visits. During the 50 nonsmoking visits, 92% of the RSP concentrations were less than 20 u,g/m3 above outdoor levels, and no concentration exceeded 100 ug/m3 on any nonsmoking visit. The data show there was a striking decline in indoor RSP concentrations in the tavern after smoking was prohibited. The indoor concentration observed in the nonsmoking periods (9.1 u.g/m3 average for all nonsmoking visits) was attributed to cooking and resuspended dust. A mathematical model based on the mass balance equation was developed that included smoking, cooking, and resuspended dust. Using cigarette emission rates from the literature, the tavern volume of 521 m3, and the air exchange rate measured in the tavern under conditions regarded by the management as "typical," the model predicted 42.5 ug/m3 for an average smoking count of 1.17 cigarettes, which compared favorably with the average concentration of 43.9 ng/m3 observed in the tavern. A regression analysis indicated that the active smoking count explained over 50% of the variation of the RSP concentrations measured on different dates. The mathematical model can be used to estimate RSP concentrations from smoking in other similar taverns under similar conditions.     

Stationary Source Surveillance for Large Air Quality Control Regions in Nonurban Areas

Increased energy processing activity in the north has resulted in a demand for measured data on plume dispersion that is relevant to this particular region. The north was, therefore, selected for study in a comprehensive government/Industry research program. The objective of these studies was to assess the behaviour of plumes in various geographic areas In Canada. The program utilizes airborne and automobile-mounted probes to determine SO₂ and temperature profiles within stock-emitted plumes as well as meteorological data on local atmospheric structure. The data are then analyzed numerically to obtain plume axis elevations and standard deviations of spread and these results are compared to accepted predictive methods. Good agreement with the analysis of Briggs was observed for predicting the location of the plume axis In neutral conditions; some deviations were noted in stable conditions. Values of the measured product ( σay-σ;z) were generally larger than those of Pasquill, particularly for those values close to the source. A difference between the measured values of (σ;y-σ;z) in fall and winter was observed in stable conditions.     

Evaluation of a Test Method for Measuring Indoor Air Emissions from Dry-Process Photocopiers

ABSTRACT

A large chamber test method for measuring indoor air emissions from office equipment was developed, evaluated, and revised based on the initial testing of four dry-process photocopiers. Because all chambers may not necessarily produce similar results (e.g., due to differences in sink effects, temperature and humidity control, air exchange, pollutant monitoring, and measurement biases), a preliminary four-laboratory evaluation of the revised test method was conducted. To minimize variability, the evaluation used a single dry-process photocopier that was shipped to each of the four laboratories along with supplies (i.e., toner and paper).

The results of this preliminary four-laboratory evaluation demonstrate that the test method was used successfully in the different chambers to measure emissions from dry-process photocopiers. Differences in chamber design and construction appeared to have had minimal effect on the results for the volatile organic compounds (VOCs). Perhaps more important than the chamber itself is the sample analysis as identified by duplicate samples that were analyzed by a different laboratory. Percent relative standard deviation (%RSD) was used to provide a simplistic view of interlaboratory precision for this evaluation. Excluding problems with suspected analytical bias observed from one of the laboratories, the precision was excellent for the VOCs with RSDs of less than 10% in most cases. Less precision was observed among the laboratories for aldehydes/ketones (RSD of 23.2% for formaldehyde). The precision for ozone emission rates among three of the laboratories was excellent (RSD of 7.9%), but emission rates measured at the fourth laboratory were much higher.