Development of front check system for final disposal. II. An approach to effective and economical arrangement of equipment

The additional time required for a front check (rapid chemical analysis for criterial components) of lorry loads arriving at a landfill has been estimated by computer simulations based on observed patterns at two landfills of different types. The advantage of separating sample preparation from analysis per se is demonstrated and queue lengths have been estimated for various configurations.     

燃煤电站环保设施多污染物控制能力分析及对策

基于日趋严峻的环境形势和严格的排放标准,面向燃煤电站多污染物控制过程,详细分析燃煤电站现有环保设施多污染物控制规律。针对协同控制过程中存在的问题,研究湿式烟气多污染物协同控制技术及对策,为实现污染物达标排放和电力工业绿色发展、循环发展和低碳发展提供技术支撑。     

Characteristics of environmental factors and their effects on CH4 and CO2 emissions from a closed landfill: An ecological case study of Shanghai

To elucidate the influence of landfill gas (LFG) emission on environmental factors, an ecological investigation that was primarily concerned with the characteristics of vegetation, cover soil, and solid waste in the landfill was carried out. Temporal and spatial variations in vegetation diversity and coverage and their effects on reducing the emission of methane in the landfill were investigated. The results showed that both vegetation coverage and diversity increased with elapsed landfill closure time. The transition trend of the vegetation species was from perennial plant (Phragmites australis) to annual plants. Perennial vegetation was the dominant type of vegetation during the early closure period, and annual vegetation coverage increased with closure time. Vegetation preferentially appeared in areas of comparatively high depth of cover soil, which was characterized by high moisture retentiveness that enabled vegetation growth. The concentrations of methane and carbon dioxide in the cover soil significantly decreased with increasing closure time. The concentrations of methane and carbon dioxide from bare cover soil were higher than those from vegetated cover soil whereas the CO₂ flux of bare cover soil was less than that of vegetated cover soil.     

A system dynamic modeling approach for evaluating municipal solid waste generation,landfill capacity and related cost management issues

As planning for sustainable municipal solid waste management has to address several inter-connected issues such as landfill capacity, environmental impacts and financial expenditure, it becomes increasingly necessary to understand the dynamic nature of their interactions. A system dynamics approach designed here attempts to address some of these issues by fitting a model framework for Newark urban region in the US, and running a forecast simulation. The dynamic system developed in this study incorporates the complexity of the waste generation and management process to some extent which is achieved through a combination of simpler sub-processes that are linked together to form a whole. The impact of decision options on the generation of waste in the city, on the remaining landfill capacity of the state, and on the economic cost or benefit actualized by different waste processing options are explored through this approach, providing valuable insights into the urban waste-management process.     

Material and energy recovery in integrated waste management systems: a life-cycle costing approach

A critical assumption of studies assessing comparatively waste management options concerns the constant average cost for selective collection regardless the source separation level (SSL) reached, and the neglect of the mass constraint. The present study compares alternative waste management scenarios through the development of a desktop model that tries to remove the above assumption. Several alternative scenarios based on different combinations of energy and materials recovery are applied to two imaginary areas modelled in order to represent a typical Northern Italian setting. External costs and benefits implied by scenarios are also considered. Scenarios are compared on the base of the full cost for treating the total waste generated in the area. The model investigates the factors that influence the relative convenience of alternative scenarios.     

Factors affecting water balance and percolate production for a landfill in operation.

Percolate production and precipitation data for a full-scale landfill in operation measured over a 13-year period were used to evaluate the impact and importance of the hydrological conditions of landfill sections on the percolate production rates. Both active (open) and closed landfill sections were included in the evaluation. A simple top cover model requiring a minimum of input data was used to simulate the percolate production as a function of precipitation and landfill section hydrology. The results showed that changes over time in the hydrology of individual landfill sections (such as section closure or plantation of trees on top of closed sections) can change total landfill percolate production by more than 100%; thus, percolate production at an active landfill can be very different from percolate production at the same landfill after closure. Furthermore, plantation of willow on top of closed sections can increase the evapotranspiration rate thereby reducing percolate production rates by up to 47% compared to a grass cover. This process, however, depends upon the availability of water in the top layer, and so the evaporation rate will be less than optimal during the summer where soil-water contents in the top cover are low.     

Integrating multi-criteria decision analysis for a GIS-based hazardous waste landfill sitting in Kurdistan Province, western Iran

The evaluation of a hazardous waste disposal site is a complicated process because it requires data from diverse social and environmental fields. These data often involve processing of a significant amount of spatial information which can be used by GIS as an important tool for land use suitability analysis. This paper presents a multi-criteria decision analysis alongside with a geospatial analysis for the selection of hazardous waste landfill sites in Kurdistan Province, western Iran. The study employs a two-stage analysis to provide a spatial decision support system for hazardous waste management in a typically under developed region. The purpose of GIS was to perform an initial screening process to eliminate unsuitable land followed by utilization of a multi-criteria decision analysis (MCDA) to identify the most suitable sites using the information provided by the regional experts with reference to new chosen criteria. Using 21 exclusionary criteria, as input layers, masked maps were prepared. Creating various intermediate or analysis map layers a final overlay map was obtained representing areas for hazardous waste landfill sites. In order to evaluate different landfill sites produced by the overlaying a landfill suitability index system was developed representing cumulative effects of relative importance (weights) and suitability values of 14 non-exclusionary criteria including several criteria resulting from field observation. Using this suitability index 15 different sites were visited and based on the numerical evaluation provided by MCDA most suitable sites were determined.     

Using integrated food‐web and population‐based models for environmental monitoring,remediation decisions,and long‐term planning

While ecologists have used food‐web models to understand how ecosystems function, the potential role of integrated food‐web and population‐based models in environmental monitoring and decision making has been ignored. Sound ecological principles should be integrated with state‐of‐the‐art monitoring and management practices. This article presents the ways in which population‐based models can answer basic ecological questions necessary for decision making about remediation and restoration, and for monitoring to ensure long‐term stewardship. Discussed are the uses of food‐web and population‐based models for understanding the movement of chemicals through different trophic levels. Three examples, including global warming, tributyltin, and monomethylmercury scenarios, are presented to illustrate how such models are useful. The responses of the component parts varies, depending on parameters such as birth, death, and respiration, as well as feeding rates, predator‐prey rates, and uptake and elimination rates. There are several different models available for decision making, with different levels of complexity, based on the specific hypothesis or question being asked and the amount of current information available. Therefore, it is recommended to use deterministic‐based, population‐based food‐web models for ecological risk assessment. © 2001 John Wiley & Sons, Inc.     

Characterization and control of odorous gases at a landfill site: a case study in Hangzhou, China

Municipal solid waste (MSW) landfills are one of the major sources of offensive odors potentially creating annoyance in adjacent communities. At the end of May 2007, an odor pollution incident occurred at the Tianziling landfill site, Hangzhou, China, where the residents lodged complaints about the intense odor from the landfill, which drew a significant attention from the government. In this study, ambient air monitoring was conducted at the Tianziling landfill site. The main odor composition of the gas samples collected on June 1st 2007 and the reduction of various odorous gases from the samples collected on June 1st 2009 due to the applied odor control techniques were determined using gas chromatography-mass spectrometry (GC-MS). In addition, variations of primary odorous gaseous (NH₃ and H₂S) concentrations at different locations in the landfill site from July 2007 to June 2009 were also investigated by using classical spectrophotometric methods. Results showed that a total of 68 volatile compounds were identified among which H₂S (56.58-579.84 μg/m³) and NH₃ (520-4460 μg/m³) were the notable odor components contributing to 4.47-10.92% and 83.91-93.94% of total concentrations, respectively. Similar spatial and temporal shifts of H₂S and NH₃ concentrations were observed and were significantly affected by environmental factors including temperature, air pressure and wind direction. Odor pollution was worse when high temperature, high humidity, low air pressure, and southeast, northeast or east wind appeared. Moreover, the environmental sampling points of the dumping area and the leachate treatment plant were found to be the main odor sources at the Tianziling landfill site. The odor control technologies used in this project had a good mitigating effect on the primary odorous compounds. This study provides long-term valuable information concerning the characteristics and control of odors at landfill sites in a long run.     

Trends in the use of Fenton,electro-Fenton and photo-Fenton for the treatment of landfill leachate

Advanced oxidation processes (AOPs) such as Fenton, electro-Fenton and photo-Fenton have been applied effectively to remove refractory organics from landfill leachate. The Fenton reaction is based on the addition of hydrogen peroxide to the wastewater or leachate in the presence of ferrous salt as a catalyst. The use of this technique has proved to be one of the best compromises for landfill leachate treatment because of its environmental and economical advantages. Fenton process has been used successfully to mineralize wide range of organic constituents present in landfill leachate particularly those recalcitrant to biological degradation. The present study reviews the use of Fenton and related processes in terms of their increased application to landfill leachate. The effects of various operating parameters and their optimum ranges for maximum COD and color removal are reviewed with the conclusion that the Fenton and related processes are effective and competitive with other technologies for degradation of both raw and pre-treated landfill leachate.     

Dense resistivity and induced polarization profiling for a landfill restoration project at H?rl?v, Southern Sweden.

A resistivity and time-domain induced polarization (IP) survey was conducted at a landfill site under restoration at H?rl?v in Southern Sweden. The covering of the landfill had begun some years ago, without keeping precise records of the work done, as is usual in such procedures. The survey was conducted in two steps, on two adjacent areas. First, a number of geoelectrical sections were made on a partly covered area that had been investigated earlier by auger drilling, in order to assist restoration. Then, a second area that should have received its final cover was imaged, and some defects in the cover could be detected and repaired. The resistivity and time-domain IP results were consistent with the results of the geotechnical drillings, and they enabled quasi-continuous mapping along the profiles. Three-dimensional visualization showed the overall consistency of the two-dimensional lines, and helped to generate a global view of the site. In spite of some ambiguities, cover and waste could be distinguished in most cases. In particular, fine-grained cover materials could be clearly distinguished from other cover materials.     

An integrated analytical framework for quantifying the LCOE of waste-to-energy facilities for a range of greenhouse gas emissions policy and technical factors

This study presents a novel integrated method for considering the economics of waste-to-energy (WTE) facilities with priced greenhouse gas (GHG) emissions based upon technical and economic characteristics of the WTE facility, MSW stream, landfill alternative, and GHG emissions policy. The study demonstrates use of the formulation for six different policy scenarios and explores sensitivity of the results to ranges of certain technical parameters as found in existing literature. The study shows that details of the GHG emissions regulations have large impact on the levelized cost of energy (LCOE) of WTE and that GHG regulations can either increase or decrease the LCOE of WTE depending on policy choices regarding biogenic fractions from combusted waste and emissions from landfills. Important policy considerations are the fraction of the carbon emissions that are priced (i.e. all emissions versus only non-biogenic emissions), whether emissions credits are allowed due to reducing fugitive landfill gas emissions, whether biogenic carbon sequestration in landfills is credited against landfill emissions, and the effectiveness of the landfill gas recovery system where waste would otherwise have been buried. The default landfill gas recovery system effectiveness assumed by much of the industry yields GHG offsets that are very close to the direct non-biogenic GHG emissions from a WTE facility, meaning that small changes in the recovery effectiveness cause relatively larger changes in the emissions factor of the WTE facility. Finally, the economics of WTE are dependent on the MSW stream composition, with paper and wood being advantageous, metal and glass being disadvantageous, and plastics, food, and yard waste being either advantageous or disadvantageous depending upon the avoided tipping fee and the GHG emissions price.     

Developing a holistic strategy for integrated waste management within municipal planning: Challenges,policies, solutions and perspectives for Hellenic municipalities in the zero-waste,low-cost direction

The present position paper addresses contemporary waste management options, weaknesses and opportunities faced by Hellenic local authorities. It focuses on state-of-the-art, tested as well as innovative, environmental management tools on a municipal scale and identifies a range of different collaboration schemes between local authorities and related service providers. Currently, a policy implementation gap is still experienced among Hellenic local authorities; it appears that administration at the local level is inadequate to manage and implement many of the general policies proposed; identify, collect, monitor and assess relevant data; and safeguard efficient and effective implementation of MSWM practices in the framework of integrated environmental management as well. This shortfall is partly due to the decentralisation of waste management issues to local authorities without a parallel substantial budgetary and capacity support, thus resulting in local activity remaining often disoriented and isolated from national strategies, therefore yielding significant planning and implementation problems and delays against pressing issues at hand as well as loss or poor use of available funds. This paper develops a systemic approach for MSWM at both the household and the non-household level, summarizes state-of-the-art available tools and compiles a set of guidelines for developing waste management master plans at the municipal level. It aims to provide a framework in the MSWM field for municipalities in Greece as well as other countries facing similar problems under often comparable socioeconomic settings.     

The collection system for residential recyclables in communities in Haidian District, Beijing: a possible approach for China recycling

Recycling and reusing recyclables is an important way to solve the municipal solid waste (MSW) problem. As the collection of solid waste takes up the largest percentage of MSW management budgets, improving the collection of recyclables is important. Since the decline of government-run waste buying depots in the late 1980s, the collection of recyclables from households and waste deposit sites in China is done by buyers with small informal bases and waste pickers, who are usually unskilled rural people who have come to the cities. Because of this, the current system is seen to have social problems. So, the recyclable collection system has both social as well as economic significance. China is in the process of rapid industrialization and urbanization, and a new mode of community collection system is emerging. It operates by market mechanisms, with waste collection companies that are supported by the municipal government, establishing recycle service sites, and employing workers to buy recyclables door-to-door. This paper is a case study of the new system in the Haidian District, Beijing. It summarizes the system, compares it to experiences in other countries and discusses whether the new approach contributes to resources recycling in China.     

Material and energy recovery in integrated waste management systems: an innovative approach for the characterization of the gaseous emissions from residual MSW bio-drying

In the sector of residual municipal solid waste management an increasing attention is put towards the role of biological treatments like bio-drying and bio-stabilization in order to decrease the need of landfilling volumes. The literature shows a lack of information concerning the emission factor of pollutants released from these processes. The available data are generally spot characterizations of concentration and air flow-rate that are used together in order to assess the emission factors. This approach caused significant differences among the available data as the release of pollutants is not steady. This paper belongs to a group of six papers concerning a research on material and energy recovery in integrated waste management systems, developed by a network of five universities. The contribution of the University of Trento, focuses on the bio-drying process with the following targets: (a) developing an innovative low cost method of sampling/measurement able to take into account the dynamics of release of pollutants; (b) checking the efficiency of a bio-filter; (c) verifying the variability of generation of some pollutants; (d) generating emission factors. The research was developed using a bio-drying pilot plant. As a treatment of the process air, the bio-reactor was coupled with a bio-filter. The emissions were characterized using an original approach based on the adoption of two measurement chambers suitable for hosting passive samplers. The passive samplers allowed the characterization of VOCs, N(2)O, NH(3) and H(2)S. A bio-chemical model, useful for energy and mass balances, supported the interpretation of the presented bio-drying run.     

Model simulations for describing water transport in a landfill with bottom ash from a municipal solid waste incinerator (MSWI): model validation and scenarios.

In the present study the water movement in a bottom ash landfill from a municipal solid waste incinerator (MSWI) was investigated. The pore regime of such landfills consists of macropores (with diameter > 50 microm), which make up about two-thirds of the total porosity and micropores. The program MACRO, which describes flow through porous media and takes both macro- and micropore flows into account, was applied. The model was calibrated with a time series from the landfill Riet, near Winterthur in Switzerland. In the present study the model was recalibrated at a time series for 1 year. With this scenario the influence of an expected reduction or increase of the porosity on leachate behaviour of such landfills over a long time (> 100 years) was studied ('long-term behaviour'). It has been shown that reliable information about water percolation can only be provided by obtaining more information about the hydraulic structure of such landfills. In particular, the number of macropores and the porosity exert great influence on the water movement.     

Cover design for radioactive and AMD-producing mine waste in the Ronneburg area, eastern Thuringia

At the former uranium mining site of Ronneburg, large scale underground and open pit mining for nearly 40 years resulted in a production of about 113,000 tonnes of uranium and about 200 million cubic metres of mine waste. In their present state, these materials cause risks to human health and strong environmental impacts and therefore demand remedial action. The remediation options available are relocation of mine spoil into the open pit and on site remediation by landscaping/contouring, placement of a cover and revegetation. A suitable vegetated cover system combined with a surface water drainage system provides long-term stability against erosion and reduces acid generation thereby meeting the main remediation objectives which are long-term reduction of radiological exposure and contaminant emissions and recultivation. The design of the cover system includes the evaluation of geotechnical, radiological, hydrological, geochemical and ecological criteria and models. The optimized overall model for the cover system has to comply with general conditions as, e.g. economic efficiency, public acceptance and sustainability. Most critical elements for the long-term performance of the cover system designed for the Beerwalde dump are the barrier system and its long-term integrity and a largely self-sustainable vegetation.