Inhibiting effects of gas–particle mixtures containing CO2, Mg(OH)2 particles,and NH4H2PO4 particles on methane explosion in a 20-L closed vessel

The main risk factors from methane explosion are the associated shock waves, flames, and harmful gases. Inert gases and inhibiting powders are commonly used to prevent and mitigate the damage caused by an explosion. In this study, three inhibitors (inert gas with 8.0 vol% CO₂, 0.25 g/L Mg(OH)₂ particles, and 0.25 g/L NH₄H₂PO₄ particles) were prepared. Their inhibiting effects on methane explosions with various concentrations of methane were tested in a nearly spherical 20-L explosion vessel. Both single-component inhibitors and gas–particle mixtures can substantially suppress methane explosions with varying degrees of success. However, various inhibitors exhibited distinct reaction mechanisms for methane gas, which indicated that their inhibiting effects for methane explosion varied. To alleviate amplitude, the ranking of single-component inhibitors for both explosion pressure (P_ex) and the rate of explosion pressure rise [(dP/dt)_ex] was as follows: CO₂, NH₄H₂PO₄ particles, and Mg(OH)₂ particles. In order of decreasing amplitude, the ranking of gas‒particle mixtures for both P_ex and (dP/dt)_ex was as follows: CO₂–NH₄H₂PO₄ mixture, CO₂‒Mg(OH)₂ mixture, and pure CO₂. Overall, the optimal suppression effect was observed in the system with the CO₂–NH₄H₂PO₄ mixture, which exhibited an eminent synergistic effect on methane explosions. The amplitudes of P_ex with methane concentrations of 7.0, 9.5, and 11.0 vol% decreased by 37.1%, 42.5%, and 98.6%, respectively, when using the CO₂–NH₄H₂PO₄ mixture. In addition, an antagonistic effect was observed with CO₂‒Mg(OH)₂ mixtures because MgO, which was generated by the thermal decomposition of Mg(OH)₂, can chemically react with water vapor and CO₂ to produce basic magnesium carbonate (xMgCO₃·yMg(OH)₂·zH₂O), thereby reducing the CO₂ concentration in a reaction system. This research revealed the inhibiting effects of gas‒particle mixtures (including CO₂, Mg(OH)₂ particles, and NH₄H₂PO₄ particles) on methane explosions and provided primary experimental data.     

Decomposition and oxidation of sodium 3,5,6-trichloropyridin-2-ol in sub- and supercritical water

Sodium 3,5,6-trichloropyridin-2-ol (STCP) is a necessary precursor compound for the production of chlorpyrifos and triclopyr, which are extensively used as pesticide and herbicide, respectively. In the process of STCP production, however, large amount of wastewater containing STCP is discharged, which causes increasingly environmental concerns. Therefore, it is of great significance to develop a rapid and effective method for the disposal of containing STCP contaminants. In this work, the thermal decomposition of STCP in sub- and supercritical water was investigated using a continuous tubular reactor. While STCP was stable below 280 °C, it could be effectively decomposed at elevated temperature. FT-IR spectra of the decomposition products indicated that the pyridine ring structure in the STCP molecule was stable even at temperatures up to 400 °C. The decomposition reaction was mainly caused by the substitution of Cl groups in the STCP molecule with OH groups, resulting in polyhydroxylated pyridines as the major decomposition product. Moreover, high pressure favored the substitution reaction. To completely decompose STCP into non-toxic or low toxic compounds, supercritical water oxidation (SCWO) was employed to evaluate the oxidation of STCP using H₂O₂ as an oxidant. It was found that STCP could be completely oxidized to H₂O, CO₂ and corresponding inorganic ammonium salts with an oxidation rate of 99%.     

Thermal hazard assessment for synthesis of 3-methylpyridine-N-oxide

The exothermic oxidation of 3-methylpyridine with hydrogen peroxide was analyzed by Reaction Calorimeter (RC1e) in semi-batch operation. Heat releasing rate and heat conversion were studied at different operating conditions, such as reaction temperature, feeding rate, the amount of catalyst and so on. The thermal hazard assessment of the oxidation was derived from the calorimetric data, such as adiabatic temperature rise (ΔT_ad) and the maximum temperature of synthesis reaction (MTSR) in out of control conditions. Along with thermal decomposition of the product, the possibility of secondary decomposition under runaway conditions was analyzed by time to maximum rate (TMR_ad). Also, risk matrix was used to assess the risk of the reaction. Results indicated that with the increase of the reaction temperature, the reaction heat release rate increased, while reaction time and exotherm decreased. With the increase of feeding time, heat releasing rate decreased, but reaction time and exotherm increased. With the amount of the catalyst increased, heat releasing rate increased, reaction time decreased and exothermic heat increased. The risk matrix showed that when the reaction temperature was 70 °C, feeding time was 1 h, and the amount of catalyst was 10 g and 15 g, respectively, the reaction risk was high and must be reduced.     

Research on the critical temperature of thermal decomposition for large cartridge emulsion explosives

Emulsion explosives are one type of main industrial explosives. The emergence of the large cartridge emulsion explosives has brought new security incidents. The differential scanning calorimeter (DSC) and the accelerating rate calorimeter (ARC) were selected for the preliminary investigation of the thermal stability of emulsion explosives. The results showed that the initial thermal decomposition temperatures were in the range of 232–239 °C in nitrogen atmosphere (220–232 °C in oxygen atmosphere) in DSC measurements and 216 °C in ARC measurements. The slow cook-off experiments were carried out to investigate the critical temperature of the thermal decomposition (T_c) of the large cartridge emulsion explosives. The results indicated that the larger the diameter of the emulsion explosives, the smaller the T_c is. For the large cartridge emulsion explosives with diameter of 70 mm, the T_c was 170 °C at the heating rate of 3 °C h⁻¹. It is a dangerous temperature for the production of the large cartridge emulsion explosives and it should cause our attention.     

PAN dust explosion inhibition mechanisms of NaHCO3 and Al(OH)3

We investigate the PAN dust explosion inhibition behaviors of NaHCO₃ and Al(OH)₃ in a 20 L spherical explosion system and a transparent pipe explosion propagation test system. The results show that, in the standard 20 L spherical explosion system, the highest PAN dust explosion concentration is 500 g/m³, the maximum explosion pressure is 0.661 MPa, and the maximum explosion pressure increase rate is 31.64 MPa/s; adding 50% NaHCO₃ and 60% Al(OH)₃ can totally inhibit PAN dust explosion. In the DN0.15 m transparent pipe explosion propagation test system, for 500 g/m³ PAN dust, the initial explosion flame velocity is 102 m/s, the initial pressure is 0.46 MPa, and the initial temperature is 967 °C; adding 60% NaHCO₃ and 70% Al(OH)₃ can totally inhibit PAN dust explosion flames. Through FTIR and TG analyses, we obtain the explosion products and pyrolysis patterns of the explosion products of PAN dust, NaHCO₃, and Al(OH)₃. On this basis, we also summarize the PAN dust explosion inhibition mechanisms of NaHCO₃ and Al(OH)₃.     

Inherently safer reactors: Improved efficiency of 3-picoline N-oxidation in the temperature range 110–125 °C

Alkylpyridine N-oxides are important intermediates in the pharmaceutical and agrochemicals industries. The N-oxides are produced via the homogeneously catalyzed oxidation of the respective alkylpyridines using a 50% excess of hydrogen peroxide. The competitive hydrogen peroxide decomposition produces oxygen in the flammable environment of alkylpyridines and thus forms a key hazard for this reaction. In this work, the N-oxidation was performed under pressure in the temperature range of 110–125 °C with different catalyst concentrations. It was shown that temperature had an undisputable positive effect on the N-oxidation efficiency. The accurate measurement of the pressure rise due to decomposition was difficult. However, only 5% of the added H₂O₂ decomposed when stoichiometric quantities were employed, even in the temperature of 110 °C. The N-oxidation was very efficient, even when the lowest concentration of catalyst employed in this study was used.     

Kinetic and 2D reactor modeling for simulation of the catalytic reduction of NOx in the monolith honeycomb reactor

Emission of NO_x is of primary environmental concern in the oil sands industry. Selective catalytic reduction (SCR) is one of the best NO_x reduction technologies. The present study discusses the testing of a mechanistic kinetic model for the SCR of NO_x to describe the kinetics of V₂O₅/TiO₂ catalysis at atmospheric pressure and a temperature of 623 K in a monolith honeycomb reactor. The modeling results impart insight into the significance of the diffusion with reaction steps and guidance for optimal monolith design for SCR. The validated expression would predict the conversion performance of the catalysts for different values of temperature inlet and ammonia concentration. A good agreement between experimental and model results has been obtained. A heterogeneous numerical model consisting of coupled mass and momentum balance equations was solved using the finite elements method without neglecting the axial dispersion term. The operating range for the catalyst relies on the NO conversion and emission. The optimum operating range for the best performance of the reactor is discussed.     

Thermal hazard evaluation for iso-octanol nitration with mixed acid

2-Ethylhexyl nitrate (2-EHN), an important additive to diesel fuel, is produced from the nitration of iso-octanol with HNO₃–H₂SO₄ mixed acid. In this study, the differential scanning calorimeter (DSC), accelerating rate calorimeter (ARC) and reaction calorimeter were used to analyze the thermal stability of 2-EHN and the thermal hazard of iso-octanol nitration. Four samples with different ratios of 2-EHN to mixed acid were tested using DSC. The results indicated that more mixed acid could catalyze the decomposition of 2-EHN. Three samples were tested using ARC and the results showed that sample 4 contained the lowest onset temperatures, T_D8 and T_D24. This shows that there is a higher probability of triggering the decomposition of the product 2-EHN from the iso-octanol nitration process. This conclusion was verified using RC1e tests at different temperatures. The RC1e experiments also indicated that the overall heat generation of these reactions was considerably large despite the high yields of the nitration process at 45 °C and 55 °C. This heat generation makes these semi-batch processes difficult to control, especially on a pilot or plant scale. Based on the maximum temperature of the synthesis reaction (MTSR) corrected by the yield, the only acceptable semi-batch process is the nitration reaction at 10 °C.     

Inhibition effects of Al(OH)3 and Mg(OH)2 on Al-Mg alloy dust explosion

To identify a superior explosion suppressant for Al-Mg alloy dust explosion, the inhibition effects of Al(OH)₃ and Mg(OH)₂ powders on Al-Mg alloy explosion were investigated. A flame propagation suppression experiment was carried out using a modified Hartmann tube experimental system, an explosion pressure suppression experiment was carried out using a 20-L spherical explosion experimental system, and the suppression mechanisms of the two kinds of powders on Al-Mg alloy dust explosion were further investigated. The results demonstrate that by increasing the mass percentages of Al(OH)₃ and Mg(OH)₂, the flame height, flame propagation speed and explosion pressure of deflagration can be effectively reduced. When 80% Mg(OH)₂ powder was added, the explosion pressure was reduced to less than 0.1 MPa, and the explosion was restrained. Due to the strong polarity of the surface of Mg(OH)₂, agglomeration easily occurs; hence, when the added quantity is small, the inhibition effect is weaker than that of Al(OH)₃. Because the Mg(OH)₂ decomposition temperature is higher, the same quantity absorbs more heat and exhibits stronger adsorption of free radicals. Therefore, to fully suppress Al-Mg alloy explosion, the suppression effect of Mg(OH)₂ powder is better.     

Two-stage biodegradation coupled with ultrafiltration for treatment of municipal landfill leachate

The municipal landfill leachate was treated in a hydrolysis–acidification reactor (HAR)/aerobic bio-contact oxidation reactor (ABOR) following a pretreatment with ultrafiltration (UF) membrane. Experiments were conducted continuously for 44 days at a constant flow rate of 20 l d⁻¹ and organic loading rates (OLRs) from 0.75 to 1.5 kgCOD m⁻³ per day. The results showed that COD of the leachate steadily decreased from 20,015 mg l⁻¹ to less than 3000 mg l⁻¹, and NH₄-N decreased from 368.6 mg l⁻¹ to 259.3 mg l⁻¹ in the UF process. The COD and NH₄-N removal efficiency of HAR was 56.7% and 27.7%, and that of ABOR was 94.6% and 86.7%, respectively. The total COD and NH₄-N removal efficiency reached 99.6% and 93.2%, respectively. UF and HAR played a critical role in raising the biodegradability of the landfill leachate, while ABOR had an important function on removing the dissolved NH₄-N in leachate.     

Inhibiting effect of inhibitors on ignition sensitivity of wood dust

Wood products are easy to produce dust in the production and processing process, and have a serious explosion risk. In order to improve the safety of wood products production, the inhibiting effects of magnesium hydroxide (MTH), SiO₂, melamine polyphosphate (MPP) on the minimum ignition energy (MIE) and minimum ignition temperature (MIT) of wood dust were experimentally studied. The results showed that the inhibiting effects of inhibitors on the MIE of wood dust show the order of MPP > SiO₂>MTH. The order of the inhibiting effects on the MIT of wood dust was MPP > MTH > SiO_2. When 10% MPP was added to wood dust, the time when the flame appears (T_appear) and the time when the flame reaches the top of the glass tube (T_top) obviously rose to 80, 140 ms. Therefore, MPP had the best inhibiting effect on the ignition sensitivity of wood dust.According to thermogravimetry (TG), differential scanning calorimetry (DSC) tests, the introduction of MPP leaded to lower maximum mass loss rate (MMLR), higher temperature corresponding to mass loss of 90% (T_0.1), residual mass and heat absorption. In addition, thermogravimetric analysis/infrared spectrometry (TG-IR) results showed that MPP produced H₂O (g) and NH₃ (g) during the thermal decomposition process, which diluted the oxygen.     

Study on decomposition of hydroxylamine/water solution

The risk evaluation of decomposition of hydroxylamine(HA)/water solution was studied experimentally. The thermal property of HA/water solution was studied from the calorimetric data obtained using the differential thermal analysis (DTA). The intensity of decomposition was studied on the basis of the results of the mini closed pressure vessel test (MCPVT) and the pressure vessel test (PVT) in addition to the steel tube test.The thermal property of HA/water solution was evaluated on the basis of results of the DTA. The heat-release onset temperatures using the no-treated stainless steel cells were more than 70 K below those measured using the GSC. This result implies that the heat-release onset temperature depends on the materials of sample cell. On the other hand, the heat of reaction did not depend on the materials of sample cell.The intensity of the thermal decomposition was investigated on the basis of results of the MCPVT, the PVT and the steel tube test. The intensity of the thermal decomposition increased as the HA concentration increased in the MCPVT. The intensity of the thermal decomposition increased greatly when the HA concentration was beyond 80wt.% in the MCPVT. It was elucidated that the thermal decomposition of HA 70wt.%/water solutions was very violent in the PVT. In addition, HA/water solutions of more than 80wt.% concentration could detonate in the steel tube test. HA 80 wt.% water/solution was easily detonated by a detonator without RDX in the steel tube test.In addition, the decomposition hazard of HA/water solution by the metal ion and the iron powder was studied in this paper. The thermal stability of HA85%/water solution with the iron ion or the iron powder was discussed on the basis of the heat-release onset temperature by the DTA. The heat-release onset temperatures decreased when the concentration of the iron ion or the iron powder increased in the DTA measurements. The reactiveness of HA/water solution with the metal ion of iron, manganese, nickel, chromium and copper was examined by measuring the mass loss of HA/water solution after the metal ion was added to HA/water solution at room temperature. The reactiveness of HA/water solution with the iron powder was also studied in this paper. The ferrous ion, the ferric ion and the iron powder reacted with HA/water solution. Ignition automatically began when the 0.2wt.% ferric ion solution was added to HA85wt.%/water solution. The mass loss rate depended on the HA concentration greater than the iron ion concentration. The mass loss rate increased when an amount of the iron powder increased. On the other hand, the decomposition reaction of HA85wt.%/water solution with Cu²⁺ was calm compared to that of the iron ion. HA/water solution did not react with Mn²⁺, Ni²⁺ and Cr³⁺ at room temperature.     

Dilute Acid Hydrolysis of Cellulose and Cellulosic Bio-Waste Using a Microwave Reactor System

The dilute acid hydrolysis of grass and cellulose with phosphoric acid was undertaken in a microwave reactor system. The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemi-cellulose hydrolysis, due to a rapid hydrolysis reaction at moderate temperatures. The optimum conditions for grass hydrolysis were found to be 2.5% phosphoric acid at a temperature of 175°C. It was found that sugar degradation occurred at acid concentrations greater than 2.5% (v/v) and temperatures greater than 175°C. In a further series of experiments, the kinetics of dilute acid hydrolysis of cellulose was investigated varying phosphoric acid concentration and reaction temperatures. The experimental data indicate that the use of microwave technology can successfully facilitate dilute acid hydrolysis of cellulose allowing high yields of glucose in short reaction times. The optimum conditions gave a yield of 90% glucose. A pseudo-homogeneous consecutive first order reaction was assumed and the reaction rate constants were calculated as: k₁ = 0.0813 s⁻¹; k₂ = 0.0075 s⁻¹, which compare favourably with reaction rate constants found in conventional non-microwave reaction systems. The kinetic analysis would indicate that the primary advantages of employing microwave heating were to: achieve a high rate constant at moderate temperatures: and to prevent ‘hot spot’ formation within the reactor, which would have cause localised degradation of glucose.     

Study of the influence of melamine polyphosphate and aluminum hydroxide on the flame propagation and explosion overpressure of aluminum magnesium alloy dust

When aluminum magnesium alloy dust floats in the air, a certain ignition energy can easily cause an accidental explosion. To prevent and control the occurrence of accidental explosions and reduce the severity of accidents, it is necessary to carry out research on the explosion suppression of aluminum magnesium alloy dust. This paper uses a vertical glass tube experimental device and a 20 L spherical explosive experimental device to carry out experimental studies on the suppression of the flame propagation and explosion overpressure of aluminum magnesium alloy dust with melamine polyphosphate (MPP) and Al(OH)₃. With increasing MPP and Al(OH)₃ concentrations, the flame brightness darkened, the flame velocity and propagation distance gradually decreased, and P_max and (dp/dt)_max decreased significantly. When the amount of MPP added reached 60%, the flame propagation distance decreased to 188 mm, which is a decrease of 68%, and the explosion overpressure decreased to 0.014 MPa, effectively suppressing the explosion of aluminum magnesium alloy dust. The experimental results showed that MPP was more effective than Al(OH)₃ in inhibiting the flame propagation and explosion overpressure of the aluminum magnesium alloy dust. Finally, the inhibitory mechanisms of the MPP and Al(OH)₃ were further investigated. The MPP and Al(OH)₃ endothermic decomposition produced an inert gas, diluted the oxygen concentration and trapped active radicals to terminate the combustion chain reaction.     

Partial nitritation of landfill leachate with varying influent composition under intermittent aeration conditions

The start-up and operation of a partial nitritation sequencing batch reactor for the treatment of landfill leachate were carried out on intermittent aeration mode. Partial nitrite accumulation was established in 15 days after the mode was changed from continuous aeration to intermittent aeration. Despite the varying influent composition, partial nitritation could be maintained by adjusting the hydraulic retention time (HRT) and the air flow rate. An increase in the air flow rate together with a decrease in air off duration can improve the partial nitritation capacity and eventually result in the development of granular sludge with fine diameters. A nitrogen loading rate of 0.71 ± 0.14 kg/m³/d and a COD removal rate of 2.21 ± 0.13 kg/m³/d were achieved under the conditions of an air flow rate of 19.36 ± 1.71 m³ air/m³/h and an air on/off duration of 1.5 min/0.7 min. When the ratio of total air flux (TAF) to the influent loading rate (ILR) was controlled at the range of 163–256 m³ air/kg COD, a stable effluent NO₃^?–N/NO_x^?–N (NO₂^?–N plus NO₃^?–N) ratio below 13% was achieved. Interestingly, the effluent pH was found to be a good indicator of the effluent NO₂^?–N/NH₄⁺–N ratio, which is an essential parameter for a subsequent anaerobic ammonium oxidation (Anammox) reactor.     

Modeling of a sequencing batch reactor treating municipal wastewater using multi-layer perceptron and radial basis function artificial neural networks

A sequencing batch reactor was modeled using multi-layer perceptron and radial basis function artificial neural networks (MLPANN and RBFANN). Then, the effects of influent concentration (IC), filling time (FT), reaction time (RT), aeration intensity (AI), SRT and MLVSS concentration were examined on the effluent concentrations of TSS, TP, COD and NH₄⁺-N. The results showed that the optimal removal efficiencies would be obtained at FT of 1 h, RT of 6 h, aeration intensity of 0.88 m³/min and SRT of 30 days. In addition, COD and TSS removal efficiencies decreased and TP and NH₄⁺-N removal efficiencies did not change significantly with increases of influent concentration. The TSS, TP, COD and NH₄⁺-N removal efficiencies were 86%, 79%, 94% and 93%, respectively. The training procedures of all contaminants were highly collaborated for both RBFANN and MLPANN models. The results of training and testing data sets showed an almost perfect match between the experimental and the simulated effluent of TSS, TP, COD and NH₄⁺-N. The results indicated that with low experimental values of input data to train ANNs the MLPANN models compared to RBFANN models are more precise due to their higher coefficient of determination (R²) and lower root mean squared errors (RMSE) values.     

Low-dose irradiation by electron beam for the treatment of high-SOx flue gas on a semi-pilot scale—Consideration of by-product quality and approach to clean technology

Attention has been focused on the treatment of lignite-fired flue gas in order to use lignite in an environmentally friendly way – (i) low-CO₂ emission, (ii) production of a valuable by-product, (iii) no discharge of wastewater, (iv) direct removal of SO₃ (strong toxicity), and (v) treatment of high SO₂ concentration. Based on these criteria, electron beam irradiation with ammonia injection was tested on a semi-pilot scale: 800 Nm³ h^?1 flow rate, 5500 ppm SO₂, 70 ppm NO_x, 22% flue gas moisture, and 75–80 °C at the reactor outlet.As an energy-saving measure, a low dose (5 kGy) of irradiation was applied: the problem lay in the by-product quality. It is considered that (NH₄)₂SO₃ and NH₄HSO₃ produced by thermal reactions are oxidized to form (NH₄)₂SO₄ (fertilizer) by an electron beam. However, not all reactions were complete because the by-product contained small amounts of H₂SO₄ and NH₂SO₃NH₄ (herbicide), so a vegetable pot test was performed to study the by-product quality: no adverse effect was observed. It is inferred from the pot test that slightly acidic soil may protect vegetables from disease and a small amount of NH₂SO₃NH₄ probably affects woody species and not herbaceous species.It is concluded that the electron beam system is noted as a multi-component pollution control process (removal of NO_x, SO₃, SO₂ and dioxins) and this system will contribute to environmentally friendly use of lignite as well as agricultural productivity via fertilizer supply.     

High efficiency of the NH4H2PO4/Mg(OH)2 composite for guaranteeing safety of wood production

Currently, China's timber industry is in high demand with the development of real estate. However, there is a certain fire hazard in the production process of wood manufacturing. Once a fire occurs, the fire is violent and the spread is rapid. Therefore, to improve the safety of its production process, ammonium dihydrogen phosphate and magnesium hydroxide were selected to prepare a new composite superfine dry powder, which was denoted as the NH₄H₂PO₄/Mg(OH)₂ composite. Furthermore, to figure out dry powders' extinction effect on Class A fire, the wood-crib fire suppression effect of the NH₄H₂PO₄/Mg(OH)₂ composite was test, and then compared with that of ultrafine dry powder (UDP) and commercial ABC dry powder (C-ABC) in a 1 m³ chamber. Three parameters of the fire extinguishing process, namely flame extinction time, powder consumption and temperature drop were adopted to measure the fire suppression performance. The results demonstrated that UDP and C-ABC both had a larger flame extinction time and powder consumption than the NH₄H₂PO₄/Mg(OH)₂ composite. Besides, a fire (wood cribs) can be extinguished by the NH₄H₂PO₄/Mg(OH)₂ composite with the fastest temperature drop and a much-improved toxic gas suppression ability. In short, the NH₄H₂PO₄/Mg(OH)₂ composite can better guarantee the safety of the wood processing production process. Moreover, the reasons for performance advantages of the NH₄H₂PO₄/Mg(OH)₂ composite were discussed.     

Determination of explosion parameters of methane-air mixtures in the chamber of 40 dm3 at normal and elevated temperature

The experimental results of the measurements of the explosion pressure and rate of explosion pressure rise as a function of molar methane concentration in the mixture with air in the 40 dm³ explosion chamber are presented. The research was aimed at determination of the explosion limits, according to the EU Standard. The influence of initial temperature of the mixture (changing in the range of 293–473 K) on the fundamental explosion parameters was also investigated. The ignition source was an induction electrical spark of the power equal to approximately 10 W. It was stated, that the increase of initial temperature of the methane-air mixture causes a significant increase of the explosion range.