Environmental impact assessment on the construction and operation of municipal solid waste sanitary landfills in developing countries: China case study

An inventory of material and energy consumption during the construction and operation (C&O) of a typical sanitary landfill site in China was calculated based on Chinese industrial standards for landfill management and design reports. The environmental impacts of landfill C&O were evaluated through life cycle assessment (LCA). The amounts of materials and energy used during this type of undertaking in China are comparable to those in developed countries, except that the consumption of concrete and asphalt is significantly higher in China. A comparison of the normalized impact potential between landfill C&O and the total landfilling technology implies that the contribution of C&O to overall landfill emissions is not negligible. The non-toxic impacts induced by C&O can be attributed mainly to the consumption of diesel used for daily operation, while the toxic impacts are primarily due to the use of mineral materials. To test the influences of different landfill C&O approaches on environmental impacts, six baseline alternatives were assessed through sensitivity analysis. If geomembranes and geonets were utilized to replace daily and intermediate soil covers and gravel drainage systems, respectively, the environmental burdens of C&O could be mitigated by between 2% and 27%. During the LCA of landfill C&O, the research scope or system boundary has to be declared when referring to material consumption values taken from the literature; for example, the misapplication of data could lead to an underestimation of diesel consumption by 60–80%.     

Investigating the performance of aerobic,semi-aerobic,and anaerobic bioreactor landfills for MSW management in developing countries

Three different laboratory bioreactors, each duplicated, with dimensions 0.5 × 0.5 × 1 m were set up and monitored for 160 days. Municipal Solid Wastes with an organic content of ~80 % and a density of 550 kg/m³ were placed in bioreactors. Fresh leachate collected from waste collection vehicles was used with a recirculation rate of 28 L/day. Aerobic bioreactors were aerated at a rate of 0.15–0.24 L/min/kg of waste. Almost the same level of treatment was observed in terms of chemical oxygen demand reduction of leachate, which was in the range of 91–93 %. However, for anaerobic bioreactor, it took almost twice the time, 160 vs. 76 days, to reach the same level of treatment and stabilization. The behavior of semi-aerobic bioreactor was somewhere between the aerobic and anaerobic ones. Total biogas production for anaerobic bioreactors was 90 L/kg of waste, which contained 57–63 % methane. Methane concentration measured in semi-aerobic bioreactor was below 5 %. The main advantage of aerobic bioreactor was the fast rate of the process, while for semi-aerobic bioreactor, it was the elimination of the need for energy to maintain aerobic conditions, and for anaerobic bioreactor it was the production of biogas and potential energy recovery.     

Recycling potential of urban solid waste destined for sanitary landfills: the case of Indaiatuba, SP, Brazil.

The urban solid waste of the city of Indaiatuba (pop. 175 000), located in the state of S?o Paulo, was characterized, focusing on the recycling potential. For this purpose, collected waste was subdivided into 27 items, classified by mass and volume. About 90% of this waste was found to be potentially recyclable and only 10% requiring landfilling. The compostable organic matter, in the form of food and garden waste, both with high moisture content (51 and 41%, respectively), represents 54% in mass and 21% in volume. The most common type of plastic in this waste is high density polyethylene, whose estimated disposal is about 5000kgday(-1). A socio-economic analysis of the waste generation indicates that low-income neighbourhoods discard relatively less packaging and more food waste, shoes and construction debris than middle and high income ones, which may be due to low purchasing power and schooling. Our findings indicate that more aluminium and uncoloured polyethylene terephthalate is discarded in the warmest months of the year, probably due to a greater consumption of canned and bottled drinks.     

Assessment of economic viability of solid waste service provision in small settlements in developing countries: case study Rosetta, Egypt

Problems associated with solid waste management (SWM) service provision in developing countries are reaching an ever increasing magnitude, leading to considerable adverse impacts on the environment and quality of life of the inhabitants. Such problems are usually associated with limited managerial, technical and financial capabilities of municipal authorities. Municipal authorities in Egypt that are responsible for SWM services have always been accused of providing a less than satisfactory service, leading to huge quantities of solid waste being uncollected. This study assesses the potential for the provision of an effective and sustainable service, by estimating willingness of the residents to pay for such a service and the cost involved in its provision. The study covered the Rosetta urban centre and its adjacent areas, which are located in the northwestern part of the Nile Delta. It was found that, from an economic perspective, a viable SWM service could be provided in the study area using local funds. In order to increase the likelihood of success of such a service, it may be provided by a local firm or a cooperative to be established for that purpose.     

Implementation of the semi-aerobic landfill system (Fukuoka method) in developing countries: a Malaysia cost analysis

Most of the existing solid waste landfill sites in developing countries are practicing either open dumping or controlled dumping. Proper sanitary landfill concepts are not fully implemented due to technological and financial constraints. Implementation of a fully engineered sanitary landfill is necessary and a more economically feasible landfill design is crucial, particularly for developing countries. This study was carried out by focusing on the economics from the development of a new landfill site within a natural clay area with no cost of synthetic liner up to 10 years after its closure by using the Fukuoka method semi-aerobic landfill system. The findings of the study show that for the development of a 15-ha landfill site in Malaysia with an estimated volume of 2,000,000 m(3), the capital investment required was about US 1,312,895 dollars, or about US 0.84 dollars/tonne of waste. Assuming that the lifespan of the landfill is 20 years, the total cost of operation was about US 11,132,536 dollars or US 7.15 dollars/tonne of waste. The closure cost of the landfill was estimated to be US 1,385,526 dollars or US 0.89 dollars/tonne of waste. Therefore, the total cost required to dispose of a tonne of waste at the semi-aerobic landfill was estimated to be US 8.89 dollars. By considering an average tipping fee of about US 7.89 dollars/tonne of waste in Malaysia in the first year, and an annual increase of 3% to about US 13.84 dollars in year-20, the overall system recorded a positive revenue of US 1,734,749 dollars. This is important information for the effort of privatisation of landfill sites in Malaysia, as well as in other developing countries, in order to secure efficient and effective landfill development and management.     

The investigation of a class of capacitated arc routing problems: the collection of garbage in developing countries

The collection, transport and disposal of solid waste, which is a highly visible and important municipal service, involves a large expenditure but receives, scant attention. This problem is even more crucial for large cities in developing countries due to the hot weather. A constructive heuristic which takes into account the environmental aspect as well as the cost is proposed to solve the routing aspect of garbage collection. This is based on a look-ahead strategy which is enhanced by two additional mechanisms. Interesting results were obtained when tested on instances with and without the presence of the effect of the environment.     

Household waste generation,composition and determining factors in rapidly urbanizing developing cities: case study of Santa Cruz de la Sierra,Bolivia

Journal of Material Cycles and Waste Management - Detailed information about waste generation rates, composition, and their influencing factors, is essential for sustainable municipal solid waste...     

Current status and challenges of remediating petroleum‐derived PAHs in soils: Nigeria as a case study for developing countries

Polycyclic aromatic hydrocarbons (PAHs) are among the world's most significant environmental organic contaminants because of their carcinogenic properties. PAHs are widely distributed globally as a result of releases from numerous natural and anthropogenic activities. Consequently, several PAH monitoring studies have been conducted and remediation approaches explored. This article aims to provide the current status of PAH distribution in Nigeria's oil and gas industrial region in relation to the technologies adopted for PAH remediation. Ideally, the findings will provide insight into the challenges in managing organic contaminants derived from petroleum exploration activities in developing countries with Nigeria as a case study.     

The collection system for residential recyclables in communities in Haidian District, Beijing: a possible approach for China recycling

Recycling and reusing recyclables is an important way to solve the municipal solid waste (MSW) problem. As the collection of solid waste takes up the largest percentage of MSW management budgets, improving the collection of recyclables is important. Since the decline of government-run waste buying depots in the late 1980s, the collection of recyclables from households and waste deposit sites in China is done by buyers with small informal bases and waste pickers, who are usually unskilled rural people who have come to the cities. Because of this, the current system is seen to have social problems. So, the recyclable collection system has both social as well as economic significance. China is in the process of rapid industrialization and urbanization, and a new mode of community collection system is emerging. It operates by market mechanisms, with waste collection companies that are supported by the municipal government, establishing recycle service sites, and employing workers to buy recyclables door-to-door. This paper is a case study of the new system in the Haidian District, Beijing. It summarizes the system, compares it to experiences in other countries and discusses whether the new approach contributes to resources recycling in China.     

The horizontal reactive media treatment well (HRX Well®) for passive in situ remediation: Design,implementation, and sustainability considerations

A new in situ remediation concept termed a Horizontal Reactive Media Treatment Well (HRX Well^®) is presented that utilizes a horizontal well filled with reactive media to passively treat contaminated groundwater in situ. The approach involves the use of a large‐diameter directionally drilled horizontal well filled with solid reactive media installed parallel to the direction of groundwater flow. The engineered contrast in hydraulic conductivity between the high in‐well reactive media and the ambient aquifer hydraulic conductivity results in the passive capture, treatment, and discharge back to the aquifer of proportionally large volumes of groundwater. Capture and treatment widths of up to tens of feet can be achieved for many aquifer settings, and reductions in downgradient concentrations and contaminant mass flux are nearly immediate. Many different types of solid‐phase reactive treatment media are already available (zero valent iron, granular activated carbon, biodegradable particulate organic matter, slow‐release oxidants, ion exchange resins, zeolite, apatite, etc.). Therefore, this concept could be used to address a wide range of contaminants. Laboratory and pilot‐scale test results and numerical flow and transport model simulations are presented that validate the concept. The HRX Well can access contaminants not accessible by conventional vertical drilling and requires no aboveground treatment or footprint and requires limited ongoing maintenance. A focused feasibility evaluation and alternatives analysis highlights the potential cost and sustainability advantages of the HRX Well compared to groundwater extraction and treatment systems or funnel and gate permeable reactive barrier technologies for long‐term plume treatment. This paper also presents considerations for design and implementation for a planned upcoming field installation.     

Heterogeneous Sulfate Formation on Dust Surface and Its Dependence on Mineralogy: Balloon-Borne Observations from Balloon-Borne Measurements in The Surface Atmosphere of Beijing, China

This study focuses on providing a direct insight into the process by which sulfate is formed on mineral dust surface in the actual atmosphere. Six sets of aerosol measurements were conducted in the outskirts of Beijing, China, in 2002–2003 using a tethered balloon. The mineralogy of individual dust particles, as well as its influence on the S (sulfur) loadings was investigated by SEM-EDX analysis of the directly collected particles. The mixed layer in the urban atmosphere was found to be quite low (500–600m), often appearing as a particle dense stagnant layer above the surface. It is suggested that mineral dust is a common and important fraction of the coarse particles in Beijing (35–68%), and that it is relatively enriched with Calcite (>28%). An exceptional amount of S was detected in the mineral particles, which can be explained neither by their original composition, nor by coagulation processes between the submicron sulfates and the dust. Heterogeneous uptake of gaseous SO₂, and its subsequent oxidation on dust was suggested as the main pathway that has actually taken place in the ambient environment. The mineral class found with the largest number of particles containing S was Calcite, followed by Dolomite, Clay, Amphibole etc., Feldspar, and Quartz. Among them, Calcite and Dolomite showed distinctly higher efficiency in collecting sulfate than the other types. A positive correlation was found with the number of S containing particles and the relative humidity. Calcite in particular, since almost all of its particles was found to contain S above 60% r.h. On the other hand, the active uptake of SO₂ by the carbonates was not suggested in the free troposphere downwind, and all the mineral classes exhibited similar S content. Relative humidity in the free troposphere was suggested as the key factor controlling the SO₂ uptake among the mineral types. In terms of sulfate loadings, the relationship was not linear, but rather increased exponentially as a function of relative humidity. The humidity-dependent uptake capacity of mineral types altogether showed an intermediate value of 0.07 gSO₄ ²⁻ g⁻¹ mineral at 30% r.h. and 0.40 gSO₄ ²⁻ g⁻¹ mineral at 80%, which is fairly consistent with laboratory experiments.     

The Svalbard Intertidal Zone: A Concept for the Use of GIS in Applied Oil Sensitivity,Vulnerability and Impact Analyses

Historical oil spills have shown that environmental damage on the seashore can be measured by acute mortality of single species and destabilisation of the communities. The biota, however, has the potential to recover over some period of time. Applied to the understanding of the fate of oil and population and community dynamics, the impact can be described by the function of the following two factors: the immediate extent and the duration of damage. A simple and robust mathematical model is developed to describe this process in the Svalbard intertidal. Based on the integral of key biological and physical factors, i.e., community specific sensitivity, oil accumulation and retention capacity of the substrate, ice-cover and wave exposure, the model is implemented by a Geographical Information System (GIS) for characterisation of the habitat’s sensitivity and vulnerability. Geomorphologic maps and georeferenced biological data are used as input. Digital maps of intertidal zone are compiled, indicating the shoreline sensitivity and vulnerability in terms of coastal segments and grid aggregations. Selected results have been used in the national assessment programme of oil development in the Barents Sea for priorities in environmental impact assessments and risk analyses as well as oil spill contingency planning.     

PCBs,PBDEs and dioxin-related compounds in floor dust from an informal end-of-life vehicle recycling site in northern Vietnam: contamination levels and implications for human exposure

Floor dusts from Vietnamese end-of-life vehicle (ELV)-processing households were investigated to elucidate the contamination levels and exposure risk of polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs) and dioxin-related compounds (DRCs). The concentrations were in order of PBDEs (260–11,000, median 280 ng/g overall) > PCBs (19–2200, median 140 ng/g) > dioxin-like PCBs (8.8–450, median 22 ng/g) ? polybrominated dibenzo-p-dioxin/dibenzofurans (PBDD/Fs, 2000–28,000, median 8500 pg/g) > polychlorinated dibenzo-p-dioxin/dibenzofurans (PCDD/Fs, 440–4100, median 1800 pg/g) > MoBPCDD/Fs (1.9–1200, median 250 pg/g). Concentrations of PCBs and DRCs were higher than those reported for Vietnamese urban houses, indicating ELV processing as a significant source of these contaminants. Higher concentrations of PCBs relative to PBDEs suggest the abundance of old electrical capacitors/transformers in ELVs. The PBDD/F and PCDD/F profiles were indicative of DecaBDE-containing materials and combustion sources, respectively. PBDFs, PCDFs and DL-PCBs were the most important dioxin-like toxic equivalent (TEQ) contributors. The estimated PCB and TEQ intake doses from dust ingestion approached or exceeded the reference doses for children living in some ELV-processing households, indicating potential health risk. More comprehensive risk assessment of the exposure to PCBs and DRCs is required for residents of informal ELV recycling sites.     

The Bacillus subtilis rec-assay: a powerful tool for the detection of genotoxic substances in the water environment. Prospect for assessing potential impact of pollutants from stabilized wastes

The Bacillus subtilis rec-assay has been specially developed to detect genotoxicity in environmental water samples. The rationale of the B. subtilis rec-assay is based on the relative difference of survival of a DNA repair-recombination proficient strain and its deficient strain, which is interpreted as genotoxicity. This assay method can be very powerful in that it has higher sensitivity for the detection of mutagens in highly polluted waters than other bacterial mutation assays. Hydrophobic fractions from various environmental waters were fractionated by using XAD-2 resins and assayed, targeting the detection of organic genotoxic substances. Genotoxic response was detected in most of them, which revealed that many unknown micropollutants with genotoxicity occur in public water bodies. Positive response was also detected from a treated municipal solid waste (MSW) landfill leachate. Genotoxicity remaining in the treated effluent suggests that genotoxic micropollutants may pass through conventional water treatment processes such as activated sludge treatment process. Without proper control of waste quality and landfill facilities, waste landfill could be a heavy pollution source.     

Strategies for the municipal waste management system to take advantage of carbon trading under competing policies: The role of energy from waste in Sydney

Climate change is a driving force behind some recent environmental legislation around the world. Greenhouse gas emission reduction targets have been set in many industrialised countries. A change in current practices of almost all greenhouse-emitting industrial sectors is unavoidable, if the set targets is to be achieved. Although, waste disposal contributes around 3% of the total greenhouse gas emissions in Australia (mainly due to fugitive methane emissions from landfills), the carbon credit and trading scheme set to start in 2010 presents significant challenges and opportunities to municipal solid waste practitioners. Technological advances in waste management, if adopted properly, allow the municipal solid waste sector to act as carbon sink, hence earning tradable carbon credits. However, due to the complexity of the system and its inherent uncertainties, optimizing it for carbon credits may worsen its performance under other criteria. We use an integrated, stochastic multi-criteria decision-making tool that we developed earlier to analyse the carbon credit potential of Sydney municipal solid waste under eleven possible future strategies. We find that the changing legislative environment is likely to make current practices highly non-optimal and increase pressures for a change of waste management strategy.