Forward osmosis coupled with lime-soda ash softening for volume minimization of reverse osmosis concentrate and CaCO3 recovery: A case study on the coal chemical industry

• Forward osmosis (FO) coupled with chemical softening for CCI ROC minimization • Effective removal of scale precursor ions by lime-soda ash softening • Enhanced water recovery from 54% to 86% by mitigation of FO membrane scaling • High-purity CaCO₃ was recovered from the softening sludge • Membrane cleaning efficiency of 88.5% was obtained by EDTA for softened ROC Reverse osmosis (RO) is frequently used for water reclamation from treated wastewater or desalination plants. The RO concentrate (ROC) produced from the coal chemical industry (CCI) generally contains refractory organic pollutants and extremely high-concentration inorganic salts with a dissolved solids content of more than 20 g/L contributed by inorganic ions, such as Na⁺, Ca²⁺, Mg²⁺, Cl⁻, and SO₄²⁻. To address this issue, in this study, we focused on coupling forward osmosis (FO) with chemical softening (FO-CS) for the volume minimization of CCI ROC and the recovery of valuable resources in the form of CaCO₃. In the case of the real raw CCI ROC, softening treatment by lime-soda ash was shown to effectively remove Ca²⁺/Ba²⁺ (>98.5%) and Mg²⁺/Sr²⁺/Si (>80%), as well as significantly mitigate membrane scaling during FO. The softened ROC and raw ROC corresponded to a maximum water recovery of 86% and 54%, respectively. During cyclic FO tests (4 × 10 h), a 27% decline in the water flux was observed for raw ROC, whereas only 4% was observed for softened ROC. The cleaning efficiency using EDTA was also found to be considerably higher for softened ROC (88.5%) than that for raw ROC (49.0%). In addition, CaCO₃ (92.2% purity) was recovered from the softening sludge with an average yield of 5.6 kg/m³ treated ROC. This study provides a proof-of-concept demonstration of the FO-CS coupling process for ROC volume minimization and valuable resources recovery, which makes the treatment of CCI ROC more efficient and more economical.     

An integrated method for the rapid dewatering and solidification/stabilization of dredged contaminated sediment with a high water content

• An integrated method, called PHDVPSS, was proposed for treating DCS. • The PHDVPSS method showed superior performance compared to conventional method. • Using the method, water content (%) of DCS decreased from 300 to<150 in 3 days. • The 56-day UCS from this method is 12‒17 times higher than conventional method. • Relative to PC, GGBS-MgO binder yielded greater reduction in the leachability. To more efficiently treat the dredged contaminated sediment (DCS) with a high water content, this study proposes an integrated method (called PHDVPSS) that uses the solidifying/stabilizing (S/S) agents and prefabricated horizontal drain (PHD) assisted by vacuum pressure (VP). Using this method, dewatering and solidification/stabilization can be carried out simultaneously such that the treatment time can be significantly shortened and the treatment efficacy can be significantly improved. A series of model tests was conducted to investigate the effectiveness of the proposed method. Experimental results indicated that the proposed PHDVPSS method showed superior performance compared to the conventional S/S method that uses Portland cement (PC) directly without prior dewatering. The 56-day unconfined compressive strength of DCS treated by the proposed method with GGBS-MgO as the binder is 12‒17 times higher than that by the conventional S/S method. DCS treated by the PHDVPSS method exhibited continuous decrease in leaching concentration of Zn with increasing curing age. The reduction of Zn leachability is more obvious when using GGBS-MgO as the binder than when using PC, because GGBS-MgO increased the residual fraction and decreased the acid soluble fraction of Zn. The microstructure analysis reveals the formation of hydrotalcite in GGBS-MgO binder, which resulted in higher mechanical strength and higher Zn stabilization efficiency.     

Design of nanofibre interlayer supported forward osmosis composite membranes and its evaluation in fouling study with cleaning

• A fine fibre (40–60 nm diameter) interlayer (~1 µm thickness) was electrospun. • Fine fibre interlayer promoted formation of defect-free dense polyamide layer. • FO membrane with dual-layer substrate had less organic fouling potential. • High reverse salt flux accelerated organic fouling on FO membrane. Nanofibre-supported forward osmosis (FO) membranes have gained popularity owing to their low structural parameters and high water flux. However, the nanofibrous membranes are less stable in long-term use, and their fouling behaviours with foulants in both feed solution (FS) and draw solution (DS) is less studied. This study developed a nanofibrous thin-film composite (TFC) FO membrane by designing a tiered dual-layer nanofibrous substrate to enhance membrane stability during long-term usage and cleaning. Various characterisation methods were used to study the effect of the electrospun nanofibre interlayer and drying time, which is the interval after removing the M-phenylenediamine (MPD) solution and before reacting with trimesoyl chloride (TMC) solution, on the intrinsic separation FO performance. The separation performance of the dual-layer nanofibrous FO membranes was examined using model foulants (sodium alginate and bovine serum albumin) in both the FS and DS. The dual-layer nanofibrous substrate was superior to the single-layer nanofibrous substrate and showed a flux of 30.2 L/m²/h (LMH) when using 1.5 mol/L NaCl against deionised (DI) water in the active layer facing draw solution (AL-DS) mode. In the fouling test, the water flux was effectively improved without sacrificing the water/solute selectivity under the condition that foulants existed in both the FS and DS. In addition, the dual-layer nanofibrous TFC FO membrane was more robust during the fouling test and cleaning.     

The combined effects of biomass and temperature on maximum specific ammonia oxidation rate in domestic wastewater treatment

• Actual SAORs was determined using MLVSS and temperature. • Measured SAOR decreased with increasing MLVSS 1.1‒8.7 g/L. • Temperature coefficient (θ) decreased with increasing MLVSS. • Nitrification process was dynamically simulated based on laboratory-scale SBR tests. • A modified model was successfully validated in pilot-scale SBR systems. Measurement and predicted variations of ammonia oxidation rate (AOR) are critical for the optimization of biological nitrogen removal, however, it is difficult to predict accurate AOR based on current models. In this study, a modified model was developed to predict AOR based on laboratory-scale tests and verified through pilot-scale tests. In biological nitrogen removal reactors, the specific ammonia oxidation rate (SAOR) was affected by both mixed liquor volatile suspended solids (MLVSS) concentration and temperature. When MLVSS increased 1.6, 4.2, and 7.1-fold (1.3‒8.9 g/L, at 20°C), the measured SAOR decreased by 21%, 49%, and 56%, respectively. Thereby, the estimated SAOR was suggested to modify when MLVSS changed through a power equation fitting. In addition, temperature coefficient (θ) was modified based on MLVSS concentration. These results suggested that the prediction of variations ammonia oxidation rate in real wastewater treatment system could be more accurate when considering the effect of MLVSS variations on SAOR.     

Quantification of pesticide residues on plastic mulching films in typical farmlands of the North China

• Pesticide residuals on mulching film of Shandong, Tianjin and Hebei. • Detected 29 pesticides in soil and 30 in mulching film. • Pesticides on plastic films: 86.4‒22213.2 ng/g and in soil: 9.3‒535.3 ng/g. • Pesticides on plastic films 20 times higher than in soil. Plastic debris as new pollutants attracts much attention in the recent years. The plastic mulching films is one of the most important plastic debirs source in the environment. The aim of this work was to investigate the current status of pesticide residues on the plastic mulching films. Based on the QuEChERS method, multi-residue methods for detection of pesticide residues with gas chromatography tandem mass spectrum (GC-MS) and high performance liquid chromatography tandem mass spectrum (HPLC-MS) were developed for the analysis of the pesticides residues in plastic film and soil samples from Tianjin, Hebei and Shandong. The total concentrations of pesticide residues were in the range of 86.4‒22213.2 ng/g in plastic film debris, which was about 20 times higher than that in soil (9.3‒535.3 ng/g). Residual level of pesticides varied greatly in different samples. The historical usage and recent application of pesticides were the main sources for pesticide residues on plastic films and soil. In short, plastic mulching films could act as a sink for pesticides in farmland and the ubiquitous pesticide residues on plastic films should draw more attention.     

Novel perspective for urban water resource management: 5R generation

• 5R (Recover, Reduce, Recycle, Resource and Reuse) approaches to manage urban water. • 5R harvests storm water, gray water and black water in several forms. • 5R offers promise for moving solutions for urban water scarcity in practice. Demand for water is expanding with increases in population, particularly in urban areas in developing countries. Additionally, urban water system needs a novel perspective for upgradation with urbanization. This perspective presents a novel 5R approach for managing urban water resources: Recover (storm water), Reduce (toilet flushing water), Recycle (gray water), Resource (black water), and Reuse (advanced-treated wastewater). The 5R generation incorporates the latest ideas for harvesting storm water, gray water, and black water in its several forms. This paper has briefly demonstrated each R of 5R generation for water treatment and reuse. China has the chance to upgrade its urban water systems according to 5R principles. Already, a demonstration project of 5R generation has been installed in Qingdao International Horticultural Exposition, and Dalian International Convention Center (China) has applied 5R, achieving over 70% water saving. The 5R offers promise for moving solutions for urban water scarcity from “hoped for in the future” to “realistic today”.     

Scenario-based assessment and multi-objective optimization of urban development plan with carrying capacity of water system

• Impact of urban development on water system is assessed with carrying capacity. • Impacts on both water resource quantity and environmental quality are involved. • Multi-objective optimization revealing system trade-off facilitate the regulation. • Efficiency, scale and structure of urban development are regulated in two stages. • A roadmap approaching more sustainable development is provided for the case city. Environmental impact assessments and subsequent regulation measures of urban development plans are critical to human progress toward sustainability, since these plans set the scale and structure targets of future socioeconomic development. A three-step methodology for assessing and optimizing an urban development plan focusing on its impacts on the water system was developed. The methodology first predicted the pressure on the water system caused by implementation of the plan under distinct scenarios, then compared the pressure with the carrying capacity threshold to verify the system status; finally, a multi-objective optimization method was used to propose regulation solutions. The methodology enabled evaluation of the water system carrying state, taking socioeconomic development uncertainties into account, and multiple sets of improvement measures under different decisionmaker preferences were generated. The methodology was applied in the case of Zhoushan city in South-east China. The assessment results showed that overloading problems occurred in 11 out of the 13 zones in Zhoushan, with the potential pressure varying from 1.1 to 18.3 times the carrying capacity. As a basic regulation measure, an environmental efficiency upgrade could relieve the overloading in 4 zones and reduce 9%‒63% of the pressure. The optimization of industrial development showed that the pressure could be controlled under the carrying capacity threshold if the planned scale was reduced by 24% and the industrial structure was transformed. Various regulation schemes including a more suitable scale and structure with necessary efficiency standards are provided for decisionmakers that can help the case city approach a more sustainable development pattern.     

Performance of activated carbon coated graphite bipolar electrodes on capacitive deionization method for salinity reduction

• Graphite bipolar electrodes act as an appropriate bed for the CDI process. • Activated carbon Coating improves the application of the electrodes. • CDI is an environmentally friendly method to apply for brackish water. • Initial concentration is the most important parameter in the CDI method. • CDI process in a batch-mode setup needs more development. This research investigates a capacitive deionization method for salinity reduction in a batch reactor as a new approach for desalination. Reductions of cost and energy compared with conventional desalination methods are the significant advantages of this approach. In this research, experiments were performed with a pair of graphite bipolar electrodes that were coated with a one-gram activated carbon solution. After completing preliminary tests, the impacts of four parameters on electrical conductivity reduction, including (1) the initial concentration of feed solution, (2) the duration of the tests, (3) the applied voltage, and (4) the pH of the solution, were examined. The results show that the maximum efficiency of electrical conductivity reduction in this laboratory-scale reactor is about 55%. Furthermore, the effects of the initial concentration of feed solution are more significant than the other parameters. Thus, using the capacitive deionization method for water desalination with low and moderate salt concentrations (i.e., brackish water) is proposed as an affordable method. Compared with conventional desalination methods, capacitive deionization is not only more efficient but also potentially more environmentally friendly.     

Sulfur cycle as an electron mediator between carbon and nitrate in a constructed wetland microcosm

• Fe(III) accepted the most electrons from organics, followed by NO₃^‒, SO₄^2‒, and O₂. • The electrons accepted by SO₄^2‒ could be stored in the solid AVS, FeS₂-S, and S⁰. • The autotrophic denitrification driven by solid S had two-phase characteristics. • A conceptual model involving electron acceptance, storage, and donation was built. • S cycle transferred electrons between organics and NO₃^‒ with an efficiency of 15%. A constructed wetland microcosm was employed to investigate the sulfur cycle-mediated electron transfer between carbon and nitrate. Sulfate accepted electrons from organics at the average rate of 0.84 mol/(m³·d) through sulfate reduction, which accounted for 20.0% of the electron input rate. The remainder of the electrons derived from organics were accepted by dissolved oxygen (2.6%), nitrate (26.8%), and iron(III) (39.9%). The sulfide produced from sulfate reduction was transformed into acid-volatile sulfide, pyrite, and elemental sulfur, which were deposited in the substratum, storing electrons in the microcosm at the average rate of 0.52 mol/(m³·d). In the presence of nitrate, the acid-volatile and elemental sulfur were oxidized to sulfate, donating electrons at the average rate of 0.14 mol/(m³·d) and driving autotrophic denitrification at the average rate of 0.30 g N/(m³·d). The overall electron transfer efficiency of the sulfur cycle for autotrophic denitrification was 15.3%. A mass balance assessment indicated that approximately 50% of the input sulfur was discharged from the microcosm, and the remainder was removed through deposition (49%) and plant uptake (1%). Dominant sulfate-reducing (i.e., Desulfovirga, Desulforhopalus, Desulfatitalea, and Desulfatirhabdium) and sulfur-oxidizing bacteria (i.e., Thiohalobacter, Thiobacillus, Sulfuritalea, and Sulfurisoma), which jointly fulfilled a sustainable sulfur cycle, were identified. These results improved understanding of electron transfers among carbon, nitrogen, and sulfur cycles in constructed wetlands, and are of engineering significance.     

Global perspectives and future research directions for the phytoremediation of heavy metal-contaminated soil: A knowledge mapping analysis from 2001 to 2020

• The overall global perspective of the PHMCS field was obtained. • PHMCS research has flourished over the past two decades. • In total, 8 clusters were obtained, and many new hot topics emerged. • “Biochar,” “Drought,” “Nanoparticle,” etc., may be future hot topics. • Five future directions are proposed. In total, 9,552 documents were extracted from the Web of Science Core Collection and subjected to knowledge mapping and visualization analysis for the field of phytoremediation of HM-contaminated soil (PHMCS) with CiteSpace 5.7 R3 software. The results showed that (1) the number of publications increased linearly over the studied period. The top 10 countries/regions, institutions and authors contributing to this field were exhibited. (2) Keyword co-occurrence cluster analysis revealed a total of 8 clusters, including “Bioremediation,” “Arsenic,” “Biochar,” “Oxidative stress,” “Hyperaccumulation,” “EDTA,” “Arbuscular mycorrhizal fungi,” and “Environmental pollution” clusters (3) In total, 334 keyword bursts were obtained, and the 25 strongest, longest duration, and newest keyboard bursts were analyzed in depth. The strongest keyword burst test showed that the hottest keywords could be divided into 7 groups, i.e., “Plant bioremediation materials,” “HM types,” “Chelating amendments,” “Other improved strategies,” “Bioremediation characteristics,” “Risk assessment,” and “Other.” Almost half of the newest topics had emerged in the past 3 years, including “biochar,” “drought,” “health risk assessment,” “electrokinetic remediation,” “nanoparticle,” and “intercropping.” (4) In total, 9 knowledge base clusters were obtained in this study. The studies of Ali et al. (2013), Blaylock et al. (1997), Huang et al. (1997), van der Ent et al. (2013), Salt et al. (1995), and Salt (1998), which had both high frequencies and the strongest burst scores, have had the most profound effects on PHMCS research. Finally, future research directions were proposed.     

Nitrate removal to its fate in wetland mesocosm filled with sponge iron: Impact of influent COD/N ratio

• CW-Fe allowed a high-performance of NO₃^‒-N removal at the COD/N ratio of 0. • Higher COD/N resulted in lower chem-denitrification and higher bio-denitrification. • The application of s-Fe⁰ contributed to TIN removal in wetland mesocosm. • s-Fe⁰ changed the main denitrifiers in wetland mesocosm. Sponge iron (s-Fe⁰) is a porous metal with the potential to be an electron donor for denitrification. This study aims to evaluate the feasibility of using s-Fe⁰ as the substrate of wetland mesocosms. Here, wetland mesocosms with the addition of s-Fe⁰ particles (CW-Fe) and a blank control group (CW-CK) were established. The NO₃^‒-N reduction property and water quality parameters (pH, DO, and ORP) were examined at three COD/N ratios (0, 5, and 10). Results showed that the NO₃^‒-N removal efficiencies were significantly increased by 6.6 to 58.9% in the presence of s-Fe⁰. NH₄⁺-N was mainly produced by chemical denitrification, and approximately 50% of the NO₃^‒-N was reduced to NH₄⁺-N, at the COD/ratio of 0. An increase of the influent COD/N ratio resulted in lower chemical denitrification and higher bio-denitrification. Although chemical denitrification mediated by s-Fe⁰ led to an accumulation of NH₄⁺-N at COD/N ratios of 0 and 5, the TIN removal efficiencies increased by 4.5%‒12.4%. Moreover, the effluent pH, DO, and ORP values showed a significant negative correlation with total Fe and Fe (II) (P<0.01). High-throughput sequencing analysis indicated that Trichococcus (77.2%) was the most abundant microorganism in the CW-Fe mesocosm, while Thauera, Zoogloea, and Herbaspirillum were the primary denitrifying bacteria. The denitrifiers, Simplicispira, Dechloromonas, and Denitratisoma, were the dominant bacteria for CW-CK. This study provides a valuable method and an improved understanding of NO₃^‒-N reduction characteristics of s-Fe⁰ in a wetland mesocosm.     

Mechanism of dichloromethane disproportionation over mesoporous TiO2 under low temperature

• Mechanism of DCM disproportionation over mesoporous TiO₂ was studied. • DCM was completely eliminated at 350℃ under 1 vol.% humidity. • Anatase (001) was the key for disproportionation. • A competitive oxidation route co-existed with disproportionation. • Disproportionation was favored at low temperature. Mesoporous TiO₂ was synthesized via nonhydrolytic template-mediated sol-gel route. Catalytic degradation performance upon dichloromethane over as-prepared mesoporous TiO₂, pure anatase and rutile were investigated respectively. Disproportionation took place over as-made mesoporous TiO₂ and pure anatase under the presence of water. The mechanism of disproportionation was studied by in situ FTIR. The interaction between chloromethoxy species and bridge coordinated methylenes was the key step of disproportionation. Formate species and methoxy groups would be formed and further turned into carbon monoxide and methyl chloride. Anatase (001) played an important role for disproportionation in that water could be dissociated into surface hydroxyl groups on such structure. As a result, the consumed hydroxyl groups would be replenished. In addition, there was another competitive oxidation route governed by free hydroxyl radicals. In this route, chloromethoxy groups would be oxidized into formate species by hydroxyl radicals transfering from the surface of TiO₂. The latter route would be more favorable at higher temperature.     

Ammonia removal from low-strength municipal wastewater by powdered resin combined with simultaneous recovery as struvite

• Powdered resin was employed for ammonia recovery from municipal wastewater. • Powdered resin achievedefficient ammonia removal under various working conditions. • Co-existing cations indicated competitive adsorption of ammonia. • Ammonia was recoveredby two-stage crystallization coupled with ion exchange. Low-strength municipal wastewater is considered to be a recoverable nutrient resource with economic and environmental benefits. Thus, various technologies for nutrient removal and recovery have been developed. In this paper, powdered ion exchange resin was employed for ammonia removal and recovery from imitated low-strength municipal wastewater. The effects of various working conditions (powdered resin dosage, initial concentration, and pH value) were studied in batch experiments to investigate the feasibility of the approach and to achieve performance optimization. The maximum adsorption capacity determined by the Langmuir model was 44.39 mg/g, which is comparable to traditional ion exchange resin. Further, the effects of co-existing cations (Ca²⁺, Mg²⁺, K⁺) were studied. Based on the above experiments, recovery of ammonia as struvite was successfully achieved by a proposed two-stage crystallization process coupled with a powdered resin ion exchange process. Scanning electron microscopy (SEM) and X-ray diffractometry (XRD) results revealed that struvite crystals were successfully gained in alkaline conditions (pH= 10). This research demonstrates that a powdered resin and two-stage crystallization process provide an innovative and promising means for highly efficient and easy recovery from low-strength municipal wastewater.     

Comparative genotoxicity of water processed by three drinking water treatment plants with different water treatment procedures

• Genotoxicity of substances is unknown in the water after treatment processes. • Genotoxicity decreased by activated carbon treatment but increased by chlorination. • Halogenated hydrocarbons and aromatic compounds contribute to genotoxicity. • Genotoxicity was assessed by umu test; acute and chronic toxicity by ECOSAR. • Inconsistent results confirmed that genotoxicity cannot be assessed by ECOSAR. Advanced water treatment is commonly used to remove micropollutants such as pesticides, endocrine disrupting chemicals, and disinfection byproducts in modern drinking water treatment plants. However, little attention has been paid to the changes in the genotoxicity of substances remaining in the water following the different water treatment processes. In this study, samples were collected from three drinking water treatment plants with different treatment processes. The treated water from each process was analyzed and compared for genotoxicity and the formation of organic compounds. The genotoxicity was evaluated by an umu test, and the acute and chronic toxicity was analyzed through Ecological Structure- Activity Relationship (ECOSAR). The results of the umu test indicated that biological activated carbon reduced the genotoxicity by 38%, 77%, and 46% in the three drinking water treatment plants, respectively, while chlorination increased the genotoxicity. Gas chromatograph-mass spectrometry analysis revealed that halogenated hydrocarbons and aromatic compounds were major contributors to genotoxicity. The results of ECOSAR were not consistent with those of the umu test. Therefore, we conclude that genotoxicity cannot be determined using ECOSAR .     

TiO2@palygorskite composite for the efficient remediation of oil spills via a dispersion-photodegradation synergy

• A novel and multi-functional clay-based oil spill remediation system was constructed. • TiO₂@PAL functions as a particulate dispersant to break oil slick into tiny droplets. • Effective dispersion leads to the direct contact of TiO₂ with oil pollutes directly. • TiO₂ loaded on PAL exhibits efficient photodegradation for oil pollutants. • TiO₂@PAL shows a typical dispersion-photocatalysis synergistic remediation. Removing spilled oil from the water surface is critically important given that oil spill accidents are a common occurrence. In this study, TiO₂@Palygorskite composite prepared by a simple coprecipitation method was used for oil spill remediation via a dispersion-photodegradation synergy. Diesel could be efficiently dispersed into small oil droplets by TiO₂@Palygorskite. These dispersed droplets had an average diameter of 20–30 mm and exhibited good time stability. The tight adsorption of TiO₂@Palygorskite on the surface of the droplets was observed in fluorescence and SEM images. As a particulate dispersant, the direct contact of TiO₂@Palygorskite with oil pollutants effectively enhanced the photodegradation efficiency of TiO₂ for oil. During the photodegradation process, •O₂⁻and •OH were detected by ESR and radical trapping experiments. The photodegradation efficiency of diesel by TiO₂@Palygorskite was enhanced by about 5 times compared with pure TiO₂ under simulated sunlight irradiation. The establishment of this new dispersion-photodegradation synergistic remediation system provides a new direction for the development of marine oil spill remediation.     

Enhancement of the electrocatalytic oxidation of antibiotic wastewater over the conductive black carbon-PbO2 electrode prepared using novel green approach

• A novel conductive carbon black modified lead dioxide electrode is synthesized. • The modified PbO₂ electrode exhibits enhanced electrochemical performances. • BBD method could predict optimal experiment conditions accurately and reliably. • The modified electrode possesses outstanding reusability and safety. The secondary pollution caused by modification of an electrode due to doping of harmful materials has long been a big concern. In this study, an environmentally friendly material, conductive carbon black, was adopted for modification of lead dioxide electrode (PbO₂). It was observed that the as-prepared conductive carbon black modified electrode (C-PbO₂) exhibited an enhanced electrocatalytical performance and more stable structure than a pristine PbO₂ electrode, and the removal efficiency of metronidazole (MNZ) and COD by a 1.0% C-PbO₂ electrode at optimal conditions was increased by 24.66% and 7.01%, respectively. Results revealed that the electrochemical degradation of MNZ wastewater followed pseudo-first-order kinetics. This intimates that the presence of conductive carbon black could improve the current efficiency, promote the generation of hydroxyl radicals, and accelerate the removal of MNZ through oxidation. In addition, MNZ degradation pathways through a C-PbO₂ electrode were proposed based on the identified intermediates. To promote the electrode to treat antibiotic wastewater, optimal experimental conditions were predicted through the Box-Behnken design (BBD) method. The results of this study suggest that a C-PbO₂ electrode may represent a promising functional material to pretreat antibiotic wastewaters.     

Significant increase of assimilable organic carbon (AOC) levels in MBR effluents followed by coagulation,ozonation and combined treatments: Implications for biostability control of reclaimed water

• Annual AOCs in MBR effluents were stable with small increase in warmer seasons. • Significant increase in AOC levels of tertiary effluents were observed. • Coagulation in prior to ozonation can reduce AOC formation in tertiary treatment. • ∆UV₂₅₄ and SUVA can be surrogates to predict the AOC changes during ozonation. As water reuse development has increased, biological stability issues associated with reclaimed water have gained attention. This study evaluated assimilable organic carbon (AOC) in effluents from a full-scale membrane biological reactor (MBR) plant and found that they were generally stable over one year (125–216 µg/L), with slight increases in warmer seasons. After additional tertiary treatments, the largest increases in absolute and specific AOCs were detected during ozonation, followed by coagulation-ozonation and coagulation. Moreover, UV₂₅₄ absorbance is known to be an effective surrogate to predict the AOC changes during ozonation. Applying coagulation prior to ozonation of MBR effluents for removal of large molecules was found to reduce the AOC formation compared with ozonation treatment alone. Finally, the results revealed that attention should be paid to seasonal variations in influent and organic fraction changes during treatment to enable sustainable water reuse.     

Transparent exopolymer particles (TEPs)-associated protobiofilm: A neglected contributor to biofouling during membrane filtration

• Bacteria could easily and quickly attached onto TEP to form protobiofilms. • TEP-protobiofilm facilitate the transport of bacteria to membrane surface. • More significant flux decline was observed in the presence of TEP-protobiofilms. • Membrane fouling shows higher sensitivity to protobiofilm not to bacteria level. Transparent exopolymer particles (TEPs) are a class of transparent gel-like polysaccharides, which have been widely detected in almost every kind of feed water to membrane systems, including freshwater, seawater and wastewater. Although TEP have been thought to be related to the membrane fouling, little information is currently available for their influential mechanisms and the pertinence to biofouling development. The present study, thus, aims to explore the impact of TEPs on biofouling development during ultrafiltration. TEP samples were inoculated with bacteria for several hours before filtration and the formation of “protobiofilm” (pre-colonized TEP by bacteria) was examined and its influence on biofouling was determined. It was observed that the bacteria can easily and quickly attach onto TEPs and form protobiofilms. Ultrafiltration experiments further revealed that TEP-protobiofilms served as carriers which facilitated and accelerated transport of bacteria to membrane surface, leading to rapid development of biofouling on the ultrafiltration membrane surfaces. Moreover, compared to the feed water containing independent bacteria and TEPs, more flux decline was observed with TEP-protobiofilms. Consequently, it appeared from this study that TEP-protobiofilms play a vital role in the development of membrane biofouling, but unfortunately, this phenomenon has been often overlooked in the literature. Obviously, these findings in turn may also challenge the current understanding of organic fouling and biofouling as membrane fouling caused by TEP-protobiofilm is a combination of both. It is expected that this study might promote further research in general membrane fouling mechanisms and the development of an effective mitigation strategy.     

The treatment of black-odorous water using tower bipolar electro-flocculation including the removal of phosphorus,turbidity, sulfion,and oxygen enrichment

• An innovative bubble column tower BPE was designed to treat the black-odorous water. • PO₄³⁻, S²⁻ and turbidity were removed, and dissolved oxygen was enriched in the BPE. • An aluminum bipolar electrode gave the best oxygen enrichment and pollutant removal. • Changes of microorganisms confirmed the improvement in water quality achieved. The large amount of municipal wastewater discharged into urban rivers sometimes exceeds the rivers’ self-purification capacity leading to black-odorous polluted water. Electro-flocculation has emerged as a powerful remediation technology. Electro-flocculation in a bubble column tower with a bipolar electrode (BPE) was tested in an attempt to overcome the high resistance and weak gas-floatation observed with a monopolar electrode (MPE) in treating such water. The BPE reactor tested had a Ti/Ta₂O₅-IrO₂ anode and a graphite cathode with an iron or aluminum bipolar electrode suspended between them. It was tested for its ability to reduce turbidity, phosphate and sulphion and to increase the concentration of dissolved oxygen. The inclusion of the bipolar electrode was found to distinctly improved the system’s conductivity. The system’s electro-flocculation and electrical floatation removed turbidity, phosphate and sulphion completely, and the dissolved oxygen level improved from 0.29 to 6.28 mg/L. An aluminum bipolar electrode performed better than an iron one. Changes in the structure of the microbial community confirmed a significant improvement in water quality.     

Effects of hydraulic retention time on net present value and performance in a membrane bioreactor treating antibiotic production wastewater

• The membrane bioreactor cost decreased by 38.2% by decreasing HRT from 72 h to 36 h. • Capital and operation costs contributed 62.1% and 37.9% to decreased costs. • The membrane bioreactor is 32.6% cheaper than the oxidation ditch for treatment. • The effluent COD also improved from 709.93±62.75 mg/L to 280±17.32 mg/L. • Further treatment also benefited from lower pretreatment investment. A cost sensitivity analysis was performed for an industrial membrane bioreactor to quantify the effects of hydraulic retention times and related operational parameters on cost. Different hydraulic retention times (72–24 h) were subjected to a flat-sheet membrane bioreactor updated from an existing 72 h oxidation ditch treating antibiotic production wastewater. Field experimental data from the membrane bioreactor, both full-scale (500 m³/d) and pilot (1.0 m³/d), were used to calculate the net present value (NPV), incorporating both capital expenditure (CAPEX) and operating expenditure. The results showed that the tank cost was estimated above membrane cost in the membrane bioreactor. The decreased hydraulic retention time from 72 to 36 h reduced the NPV by 38.2%, where capital expenditure contributed 24.2% more than operational expenditure. Tank construction cost was decisive in determining the net present value contributed 62.1% to the capital expenditure. The membrane bioreactor has the advantage of a longer lifespan flat-sheet membrane, while flux decline was tolerable. The antibiotics decreased to 1.87±0.33 mg/L in the MBR effluent. The upgrade to the membrane bioreactor also benefited further treatments by 10.1%–44.7% lower direct investment.