连续微滤系统膜垢生长过程的模型与模拟

应用分形理论中DLA模型,建立了膜垢分形生长模型。通过改变边界条件和随机粒子产生的几率,得到不同条件下膜垢形成与生长过程的模拟图像;采用显微粒子图像技术,通过量子点荧光示踪剂对不同条件下连续微滤系统膜垢的形态和流场进行同时观测与分析。结果表明,模拟与实验所获得的分形维数相近,该模型能够较好地模拟膜垢形成与生长过程;运用该模型数值模拟分析了流场和悬浮物浓度对膜垢生长过程的影响及其动态变化规律。     

微污染矿井水中微絮体的形成及分形特征

利用分形理论阐述了微污染矿井水中微絮体形成的分形生长特征,考察了微絮体形成过程中的影响因素,探讨了微絮凝机理,利用絮体的分形维数表征各影响因素对微絮体形态的作用结果,结果表明,微絮体形态与其分形维数之间具有良好的相关性,且分形维数越大,微絮体更加紧实,越易于沉降,滤后水的浊度越小;同时考察了微量铁锰离子对微絮体形态的影响,为微絮凝深床过滤工艺参数的改进提出了建议.     

pH对混凝超滤组合工艺性能的影响

在聚合氯化铝(PACl)投加量为4 mg/L条件下,通过调节原水的初始p H值,考察p H条件对混凝超滤组合工艺的净水性能及膜污染的影响。结果表明:当p H为7.5时,组合工艺对COD_(Mn)、UV_(254)、DOC的去除率分别为40.2%、35.4%和36.1%;当p H降至4.5时,对应的去除率分别增加至52.9%、52.1%和42.0%。酸性条件下,膜池内絮体的分形维数大,絮体结构密实,膜污染速率较快;当p H等于4.5时,絮体分形维数为1.75±0.15,尺寸大于500μm的絮体数占总絮体数的9%。中性及偏碱性条件下,絮体分形维数小,絮体结构松散多枝,膜污染速率缓慢;当p H等于7.5时,絮体分形维数为1.37±0.05,尺寸大于500μm的絮体占65%。针对该水库的水质状况,控制原水p H为7.5有利于混凝超滤膜组合装置的运行。     

盐类对模拟胞外聚合物(EPS)膜污染的影响

实验旨在研究盐类对模拟胞外聚合物(EPS)溶液在超滤和微滤过程中膜污染影响,通过添加与无添加盐类的模拟溶液的比较,研究盐类对EPS膜过滤在死端过滤过程的影响。实验考察了不同模拟溶液的膜通量衰减情况和滤饼比阻,并利用Hermia模型对实验数据进行拟合分析验证膜污染机理。实验结果表明,在超滤过程中,Ca2+和Al3+能在一定程度上提高膜通量,降低滤饼比阻,延缓膜污染;在微滤过程中,两者的添加反而降低了初始通量,添加Ca2+后滤饼比阻值反而有所增大;Na+对超/微滤过程影响很小。通过Hermia模型拟合分析发现,在超滤过程中,添加盐和无添加的溶液均以滤饼堵塞机理为主,而在微滤过程中则是以中间堵塞和滤饼堵塞机理为主。     

pH对钢铁废水再生过程中CMF系统的影响

通过中试实验研究了钢铁废水再生过程中pH变化对微滤系统性能的影响。结果表明,进水pH的升高增加了微滤膜对UV254、Ca2+和总铁的去除,同时引起了有机物以及无机沉淀物在膜面的吸附。铁锰无机沉淀物在膜面的吸附和对膜孔的堵塞是引起膜污染的主要因素。降低pH有助于控制无机沉淀在膜面和膜孔内的形成,抑制膜污染的形成。     

TiO_2光催化对微滤去除腐殖酸的膜污染控制研究

着重研究了不同紫外灯光源和照射时间条件下,TiO_2光催化(PCO)对微滤去除腐殖酸过程中的膜污染控制,并探讨了膜污染的控制机理。研究结果表明,TiO_2光催化能有效提高微滤对腐殖酸的去除,同时降低膜通量的下降,起到有效控制膜污染的作用。进一步的实验分析表明,TiO_2光催化控制膜污染的主要机理在于将腐殖酸降解为易于被TiO_2吸附的小分子量物质,吸附腐殖酸降解产物后的TiO_2聚合颗粒粒径增大,易于在膜表面形成更为松散的沉积层,并使膜污染从以膜孔堵塞和沉积层污染为主转化为以沉积层污染为主的可逆性污染。     

TiO2光催化对微滤去除腐殖酸的膜污染控制研究

着重研究了不同紫外灯光源和照射时间条件下,TiO2光催化（PCO）对微滤去除腐殖酸过程中的膜污染控制,并探讨了膜污染的控制机理。研究结果表明,TiO2光催化能有效提高微滤对腐殖酸的去除,同时降低膜通量的下降,起到有效控制膜污染的作用。进一步的实验分析表明,TiO2光催化控制膜污染的主要机理在于将腐殖酸降解为易于被TiO2吸附的小分子量物质,吸附腐殖酸降解产物后的TiO2聚合颗粒粒径增大,易于在膜表面形成更为松散的沉积层,并使膜污染从以膜孔堵塞和沉积层污染为主转化为以沉积层污染为主的可逆性污染。     

浸没式超滤膜替代砂滤处理东江水的中试研究

针对传统饮用水处理工艺的升级改造问题,通过中试实验,系统考察浸没式超滤膜替代砂滤处理东江水的出水水质并研究高通量条件下的膜运行条件。结果表明,浸没式超滤膜出水浊度不受原水水质条件影响,均保持在0.1 NTU以下,与砂滤出水相比具有优势,但有机物去除率与砂滤相差不大。膜系统在高通量条件下运行时,过滤周期应作适当的缩短,采用合理的物理清洗来缓解膜污染,并辅助以有效的在线化学清洗可保证膜过滤的长期稳定运行。     

一体式膜生物反应器处理印染废水的膜污染模型研究

利用自行研制的水解酸化+一体式膜生物反应器(SMBR)中试系统处理印染废水,通过均匀设计法设置了10组试验.计算各运行条件下的膜过滤阻力.建立了曝气量(G)、混合液污泥浓度(X)和膜通量(J)对膜面污泥沉积速率(K)的影响模型:K=3.645×107·X0.312·J0.13·G-3.46.通过该模型,可以对不同运行条件下的膜污染发展情况进行预测.验证结果表明,实际运行的测试数据与模型预测值符合性很好,可利用建立的模型预测不同运行条件下的膜污染状况.     

电絮凝延缓陶瓷微滤膜污染

为提高陶瓷微滤膜净化微污染水源水时的产水量,采用电絮凝预处理工艺延缓陶瓷膜的污染。研究了电流密度、进水流量以及跨膜压差对组合工艺产水量的影响,结果显示,较之原水直接微滤,电絮凝预处理后膜产水量得到提升。其最佳运行参数为:电流密度1.5 m A/cm2,进水流量3 L/min,跨膜压差0.15 MPa。同时,比较了碱型、氧化型和配位型药剂清洗对膜污染的影响,结果表明,先用氧化型药剂清洗,再用配位型药剂清洗的方式膜通量恢复值最高。     

二级出水微滤过程中对醋酸纤维素酯膜的有机污染特征

低压膜过滤技术(包括微滤和超滤)在再生水生产领域正引起越来越广泛的关注。然而如何解决低压膜过滤过程中的膜有机污染问题始终是膜技术所面临的技术挑战。本研究采用醋酸纤维素酯微孔滤膜对二级出水溶解性有机物(EfOM)及其不同亲疏水性组分、蛋白模拟溶液、腐殖酸(HA)等进行恒流过滤实验。对不同有机物污染后的膜表面使用全反射傅立叶红外光谱(ATR-FTIR)和X射线电子能谱(XPS)进行表征。结果表明,相对于蛋白质和EfOM等,HA所造成的膜污染最少。ATR-FTIR的结果同时显示,以官能团而言,更多的氨化物(1535cm-1)、脂肪族物质(2860～2970cm-1)和氢氧根(3400cm-1)存在于膜表面。TMP/V数据比较结果表明,在EfOM各亲疏水性组分、蛋白质和HA的对比中,EfOM中的疏水碱性物质(HPO-B)对膜污染的贡献最大,而HA的膜污染贡献最小。UVA和荧光激发-发射光谱(FEEM)结果表明,HPO-B和蛋白质对醋酸纤维素酯膜的污染贡献较大。综合不同分析手段可以对不同有机物造成膜污染的潜能大小得出如下排序:HPO-B>蛋白质>HPO-A、HPI>HA。     

Irreversible fouling during multicycle microfiltration of wastewater effluent

This study focused on irreversible fouling during microfiltration of primary and secondary effluents from municipal wastewater treatment plants. Flow resistances were calculated from the sum of clean membrane resistances, resultant cake layer resistances, and consequent irreversible fouling resistances. Results from a dead-end cell experimental system showed that the accumulated cake resistance was dominating for microfiltration of primary/secondary effluents. Suspended solids in the primary and secondary effluents had a similar compressibility index, n, with a value of approximately 0.5, indicating that they were moderately compressible particles. The value of irreversible resistance is dependent on the intensity of membrane cleaning; however, for a given membrane cleaning strategy, this value steadily increased and reached a maximum after approximately 6 cycles of filtration and cleaning. This study provided an explanation for the significant drop of throughput flux in the early application of membrane processes, and a plateau flux approached correspondingly.     

预涂动态膜在乳化油废水处理中的阻力分布及其抗污染特性

为讨论预涂动态膜的抗污染特性,测定了陶瓷膜、高岭土预涂动态膜和高岭土/MnO2复合预涂动态膜分别在乳化油废水处理中的阻力分布,并用SEM扫描电镜对污染预涂动态膜形貌进行了表征。结果表明,乳化油污染阻力明显高于基膜(或陶瓷膜)固有阻力及涂膜粒子形成的阻力,乳化油对预涂动态膜或陶瓷膜的污染是导致膜通量衰减的主要原因;高岭土和复合预涂动态膜所用基膜污染阻力低于陶瓷膜的内部污染阻力,其中复合预涂动态膜所用基膜的污染阻力最小;复合动态膜层比高岭土动态膜层的污染程度低;污染预涂动态膜表面呈现明显的凝胶态物质,其基膜外壁面未呈现凝胶态物质。处理乳化油废水中,动态膜层可有效保护基膜,表现出了较强的抗污染性能。     

印染废水回用微滤膜污染控制研究

采用PVDF中空纤维微滤膜处理某纺织印染厂二级生化出水,研究了膜污染控制及清洗方法。结果表明,合理的膜通量是控制膜污染、保证膜寿命的关键,采用31 L/(m2.h)左右的通量有助于膜污染的控制。氢氧化钠与次氯酸钠可分别用于日常维护清洗与恢复清洗,通过循环正洗不仅能满足清洗要求,且药剂使用量也小于反洗方法,每吨产水清洗用碱费用仅0.06元。化学清洗后再水力正洗,能进一步提高清洗效果。     

Matrix effect in case of purification of oily waters by membrane separation combined with pre-ozonation

In the present study, oil in water emulsions (c_oil?=?100 ppm; d_{oil droplets}?<?2 μm) was purified with ozonation followed by microfiltration using polyethersulfone (PES) membrane (d_pore?=?0.2 μm). The effects of pre-ozonation on membrane microfiltration were investigated in detail both in case of ultrapure and model groundwater matrices, applying different durations (0, 5, 10, and 20 min) of pre-ozonation. Simultaneously, the effects of added inorganic water components on the combined method were investigated. Size distribution of oil droplets, zeta potentials, fluxes, and purification efficiencies were measured and fouling mechanisms were described in all cases. It was found that the matrix significantly affected the size distribution and adherence ability of oil droplets onto the membrane surface, therefore fouling mechanisms also were strongly dependent on the matrix. In case of low salt concentration, the total resistance was caused mainly by reversible resistance, which could be significantly reduced (eliminated) by pre-ozonation. In case of model groundwater matrix, nearly twice higher total resistance was measured, and irreversible resistance was dominant, because of the higher adhesion ability of the oil droplets onto the membrane surface. In this case, pre-ozonation resulted in much lower irreversible, but higher reversible resistance. Increased duration of pre-ozonation raised the total resistance and reduced the elimination efficiency (due to fragmented oil droplets and water soluble oxidation by-products) in both cases, therefore short pre-ozonation can be recommended both from economic and performance aspects.     

好氧颗粒污泥动态膜生物反应器工艺参数及运行性能

以一体式尼龙筛网动态膜生物反应器(DMBR)为研究体系,与好氧颗粒污泥相结合,形成新的好氧颗粒污泥动态膜生物反应器(AGDMBR),探讨了在新工艺条件下对COD、氨氮的去除,以及出水浊度的变化,与活性污泥动态膜生物反应器(DMBR)做比较,研究了进水流量、曝气量等工艺运行参数与膜污染之间的关系,并对系统中污泥的EPS进行分析。结论表明,AGDMBR系统对COD和NH4+-N的平均去除率分别为91%和95%,出水浊度为6 NTU,处理效果均优于DMBR系统;AGDMBR系统在运行过程中膜污染速度随进水流量的增大而加快;曝气量为125～150 L/h时,膜通量持续时间最长;AGDMBR系统比DMBR系统在膜污染的延缓上具有明显的优势。     

Electrocoagulation-integrated hybrid membrane processes for the treatment of tannery wastewater

Three different combinations of treatment techniques, i.e. electrocoagulation combined with microfiltration (EMR), membrane bioreactor (MBR) and electrocoagulation integrated with membrane bioreactor (hybrid MBR, (HMBR)), were analysed and compared for the treatment of tannery wastewater operated for 7 days under the constant trans-membrane pressure of 5 kPa. HMBR was found to be most suitable in performance as well as fouling reduction, with 94 % of chemical oxygen demand (COD) removal, 100 % chromium removal and 8 % improvement in percentage reduction in permeate flux compared to MBR with only 90 % COD removal and 67 % chromium removal. The effect of mixed liquor suspended solids on fouling was also investigated and was found to be insignificant. EMR was capable of elevating the flux but was not as efficient as HMBR and MBR in COD removal. Fouling reduction by HMBR was further confirmed by SEM-EDX and particle size analysis.