Facile Preparation of Chitin/Cellulose Composite Films Using Ionic Liquids

In this study, we performed the facile preparation of chitin/cellulose composite films using two ionic liquids, 1-allyl-3-methylimidazolium bromide (AMIMBr) and 1-butyl-3-methylimidazolium chloride (BMIMCl); the former dissolves chitin and the latter dissolves cellulose. First, solutions of chitin in AMIMBr and cellulose in BMIMCl were individually prepared by heating each mixture at 100 °C for 24 h. Then, the homogeneous mixture of the two solutions was thinly casted on a glass plate, followed by standing at room temperature for 2 h. After the material was subjected to successive Soxhlet extractions with ethanol for 12 h and with water for 12 h, the residue was dried at room temperature to give a composite film. The crystalline structures of the polysaccharides were evaluated by the X-ray diffraction measurement. Furthermore, the thermal stability and mechanical property of the resulting composite film were estimated by the thermal gravimetric analysis measurement and tensile testing, respectively.     

Preparation of Galactomannan-Based Materials Compatibilized with Ionic Liquids

This paper reports the preparation of galactomannan/ionic liquid composite materials from the corresponding ion gels. Three kinds of galactomannans, that is, fenugreek gum (FG), guar gum (GG), and locust bean gum (LBG) and an ionic liquid of 1-butyl-3-methylimidazolium chloride (BMIMCl) were used. When the galactomannan/BMIMCl gels were immersed in ethanol, followed by dryness under reduced pressure, the galactomannan/BMIMCl composite materials were obtained. The crystalline structures of galactomannans in the materials were evaluated by the powder X-ray diffraction measurement. The mechanical property of the FG/BMIMCl composite material under compressive mode was superior compared with the GG and LBG/BMIMCl composite materials. Then, FG films compatibilized with polymeric ionic liquids (PILs) were also prepared by in situ radical polymerization of polymerizable ionic liquids, 1-(3-acryloyloxypropyl)-3-vinylimidazolium bromide and 1-methyl-3-vinylbenzylimidazolium chloride by AIBN in mixtures of FG with BMIMCl. The mechanical properties of the resulting films were affected by the FG/PIL ratios as well as the unit ratios in PILs.     

Preparation of Cellulose/Xanthan Gum Composite Films and Hydrogels Using Ionic Liquid

This paper reports the preparation of cellulose/xanthan gum composite films and hydrogels through gelation with an ionic liquid. Mixtures of cellulose and xanthan gum in desired weight ratios with an ionic liquid, 1-butyl-3-methylimidazolium chloride (BMIMCl), were thinly placed on a Petri dish and heated at 100 °C for 9 h to obtain the solutions. Then, the solutions were left standing at room temperature for 1 day for the progress of gelation. The resulting ion gels were subjected to Soxhlet extraction with ethanol to remove BMIMCl, followed by drying under ambient conditions to obtain the composite films. The crystalline structures of the polysaccharides and the mechanical properties were evaluated by powder X-ray diffraction measurement and tensile testing of the films, respectively. The ion gels in various cellulose/xanthan gum weight ratios, which were prepared in a test tube by the same procedure, were immersed in water for the exchange of disperse media to obtain the cellulose/xanthan gum composite hydrogels. Water contents of all the materials were higher than 90 %. The mechanical properties of the hydrogels were evaluated by compressive testing.     

Mechanical Performance and Design Criteria of Biodegradable Low-tunnel Films

The overall mechanical behaviour of a series of experimental Mater-Bi made thin low-tunnel films is analysed with respect to the effect of two major factors: the film processing optimisation during manufacturing and the design of the low-tunnels structural system. The analysis of the mechanical behaviour of the biodegradable low-tunnel films, based on the results of extensive full-scale and small-scale experiments, combined with laboratory testing of the mechanical properties of the film, proves that a rather good mechanical behaviour is possible for these films, comparable to the behaviour of conventional agricultural films in terms of strength, provided that two criteria are met: (a) the low tunnel structural design is based on the initial stress at yield value of the film, which represents the asymptotic value of the tensile strength of the film, following its evolution with the time of exposure to real field conditions; (b) the processing of the film is optimised for the particular biodegradable material and film thickness under consideration. It is also confirmed that the stabilisation schemes used with conventional polyethylene films are not suitable for the biodegradable films.

Experimental Investigation of Cellulose/Silver Nanocomposites Using In Situ Generation Method

Cellulose gel films were prepared by regeneration process using pre-cooled aq.(8 wt% LiOH + 15 wt% urea) mixture as solvent and ethyl alcohol as non solvent. The Terminus cattapa leaf extract diffused wet cellulose films were then dipped in 1–5 mM aq.AgNO₃ solutions to allow in situ generation of silver nanoparticles (AgNPs). Besides the in situ generation, some AgNPs were also formed outside the wet films in the solution. The AgNPs formed outside the films were observed under transmission electron microscope and scanning electron microscope. The nanocomposite films were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction and thermogravimetric analysis and tensile test. The thermal stability of the composite films was lower than that of the matrix up to a temperature of ~300 °C and afterwards showed a reverse trend. The tensile strength of the nanocomposite films was found to be higher than the matrix but decreased with increasing concentration of aq.AgNO₃. The cellulose/AgNPs composite films showed good antibacterial activity against E. coli (gram positive) and Bacillus sp. (gram negative). Based on the aforementioned properties, the cellulose/AgNPs composite films can be considered for antibacterial packaging and medical applications.     

Photodegradation of Poly(lactic acid) Stereocomplex by UV-Irradiation

Neat poly(l-lactic acid) (PLLA) and poly(d-lactic acid) (PDLA) films and PLLA/PDLA blend films were prepared by solution casting, and their photodegradation by UV-irradiation was investigated using wide-angle X-ray scattering (WAXS), gel permeation chromatography, differential scanning calorimetry, tensile testing, and polarized optical microscopy. The PLLA/PDLA blend film was more photodegradation-resistant than the neat PLLA and PDLA films when photodegradation was monitored by molecular weight, melting temperature, and WAXS crystalline peak positions. This indicates that the chains in both amorphous and crystalline regions of the PLLA/PDLA blend film were photo-cleavage-resistant compared to those of the neat PLLA and PDLA films. The changes in melting temperature and WAXS crystalline peak positions before and after photodegradation respectively indicated the increased crystalline lattice disorder and the decreased crystalline lattice sizes of the neat PLLA and PDLA films, whereas these changes were insignificant for the blend films. Photodegradation caused no significant change in tensile properties, with the exception of significant decreases in the tensile strength and elongation at break of PLLA/PDLA blend film. However, the tensile strength and elongation at break of the PLLA/PDLA blend film retained higher values compared to those of the neat PLLA and PDLA films during photodegradation. In spite of the slower photodegradation of the PLLA/PDLA blend film traced by M _n, T _m, and WAXS crystalline peak positions than that of neat PLLA and PDLA films, the rapid decrease in tensile strength and elongation at break of the former than that of the latter should be due to the highly-ordered structural difference between them, i.e., the three dimensional dry gel of the former and the spherulites of the latter.     

Comparative Response of Indigenously Developed Bacterial Consortia on Progressive Degradation of Polyhydroxybutyrate Film Composites

The global demand of bioplastics has lead to an exponential increase in their production commercially. Hence, biodegradable nature needs to be evaluated in various ecosystems viz. air, water, soil and other environmental conditions to avoid the polymeric waste accumulation in the nature. In this paper, we investigated the progressive response of two indigenously developed bacterial consortia, i.e., consortium-I (C-I: Pseudomonas sp. strain Rb10, Pseudomonas sp. strain Rb11 and Bacillus sp. strain Rb18), and consortium-II (C-II: Lysinibacillus sp. strain Rb1, Pseudomonas sp. strain Rb13 and Pseudomonas sp. strain Rb19), against biodegradation behavior of polyhydroxybutyrate (PHB) film composites, under natural soil ecosystem (in net house). The biodegraded films recovered after 6 and 9 months of incubation were analyzed through Fourier transform infrared spectroscopy and scanning electron microscopy to determine the variations in chemical and morphological parameters (before and after incubation). Noticeable changes in the bond intensity, surface morphology and conductivity were found when PHB composites were treated with C-II. These changes were drastic in case of blends in comparison to copolymer. The potential isolates not only survived, but, also, there was a significant increase in bacterial diversity during whole period of incubation. To the best of our knowledge, it is the first report which described the biodegradation potential of Lysinibacillus sp. as a part of C-II with Pseudomonas sp. against PHB film composites.     

Life Cycle Analysis of Extruded Films Based on Poly(lactic acid)/Cellulose Nanocrystal/Limonene: A Comparative Study with ATBC Plasticized PLA/OMMT Systems

Life cycle analysis (LCA) of limonene plasticized poly(lactic acid) (PLA) films containing cellulose nanocrystals (CNC) extracted, by acid hydrolysis, from Phormium tenax leaf fibres, was assessed and compared with the results of acetyl tributyl citrate (ATBC) plasticized PLA films, having equivalent mechanical properties, containing organo-modified montmorillonite (OMMT). Eco-Indicator 99 tool has been adopted as the main method for life cycle assessment. Results indicated that, despite CNC are biobased fillers obtained by natural sources, the related chemical extraction leads to a large environmental footprint and a relatively relevant energy expense. LCA characterization of these films demonstrated that the environmental impact of PLA/limonene film reinforced with 1% in weight of CNC (PLA/CNC/limonene) is comparable to the environmental impact of polylactic acid films reinforced with OMMT and plasticized with a petroleum based plasticizer (ATBC) (PLA/OMTT/ATBC). A “cradle to gate” approach has been considered for both the film typologies.     

Longitudinal Dispersion Characteristics of Rivers and Natural Streams in Greece

An optimized parameterization of the non-dimensional longitudinal dispersion coefficients in Greek rivers, $K_{x_a } $ , is described in terms of parameters derived from cross-section river geometry and longitudinal velocity data. Optimization is accomplished, using various combinations of the selected parameters, either for subsets of $K_{x_a } $ values, according to the cross-section aspect ratio range, or for the entire $K_{x_a } $ population. The use of shape factors associated with the river cross-section transverse profiles of depth-mean longitudinal velocities and the normalized intensities of longitudinal velocity variations from the overall mean cross-sectional velocity improves the parameterization. The statistical behavior of $K_{x_a } $ in terms of skewness, flatness and other shape coefficients is also examined. $K_{x_a } $ histograms show that these coefficients have a log-normal distribution. An empirical expression for $K_{x_a } $ is also proposed that takes into account both contributions from the transverse velocity profile and from the vertical profile of longitudinal velocities, at each cross-section, in shaping the value of dispersion coefficients when the aspect ratio of the cross-section is of O(1) and/or when $K_{x_a } $ is of O(1).     

Life Cycle Assessment of Polysaccharide Materials: A Review

Apart from conventional uses of polysaccharide materials, such as food, clothing, paper packaging and construction, new polysaccharide products and materials have been developed. This paper reviews life cycle assessment (LCA) studies in order to gain insight of the environmental profiles of polysaccharide products (e.g. viscose or natural fibre polymer composites) in comparison with their conventional counterparts (e.g. cotton or petrochemical polymers). The application areas covered are textiles, engineering materials and packing. It is found that for each stage of the life cycle (production, use phase and waste management) polysaccharide-based end products show better environmental profiles than their conventional counterparts in terms of non-renewable energy use (NREU) and greenhouse gas (GHG) emissions. Cotton is an exception, with high environmental impacts that are related to the use of fertilisers, herbicides, pesticides and high water consumption. The available literature for man-made cellulose fibres shows that they allow to reduce NREU and GHG emissions in the fibre production phase. No study has been found for the fabric production and the use phase of man-made cellulose textiles.

Polyvinyl Alcohol (PVA)/Starch Bioactive Packaging Film Enriched with Antioxidants from Spent Coffee Ground and Citric Acid

The bioactive packaging polyvinyl alcohol (PVA)/starch films were prepared by incorporating combined antioxidant agents i.e. extracted spent coffee ground (ex-SCG) and citric acid. Effect of citric acid content on chemical compatibility, releasing of antioxidant, antibacterial activities, and physical and mechanical properties of PVA/starch incorporated ex-SCG (PSt-E) films was studied. The results of ATR-FTIR spectra showed that antioxidant agents of ex-SCG can penetrate into the film and the ester bond of blended films by citric acid was also observed. The presence of ex-SCG increased efficiency of antioxidant release and antimicrobial activity. The PSt-E film incorporated 30 wt% citric acid showed minimum inhibitory concentration against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). The incorporation of ex-SCG and citric acid into film showed a synergistic effect on antibacterial activity. The water resistance and kinetic moisture sorption improved with incorporation of citric acid. The tensile strength and biodegradability of samples were in range of 5.63–7.44 MPa and 65.28–86.64%, respectively. Based on this study, PSt-E film incorporated 30 wt% citric acid can be applied as novel food packaging materials.     

Microbial Degradation of UV-Pretreated Low-Density Polyethylene Films by Novel Polyethylene-Degrading Bacteria Isolated from Plastic-Dump Soil

Eleven effective low-density polyethylene (LDPE)-degrading bacterial strains were isolated and identified from landfill soil containing large amounts of plastic materials. The isolates belonged to 8 genera, and included Pseudomonas (areroginosa and putida), Sphingobacterium (moltivorum), Delftia (tsuruhatansis), Stentrophomonas (humi and maltophilia), Ochrobacterum (oryzeae and humi), Micrococcus (luteus), Acinetobacter (pitti), and Citrobacter (amalonaticus). Abiotic degradation of LDPE films by artificial and natural ultraviolet (UV)-exposure was analyzed by FT-IR spectroscopy. LDPE films treated with UV-radiation were also inoculated with the isolates and biofilm production and LDPE degradation were measured. Surface changes to the LDPE induced by bacterial biofilm formation were visualized by Scanning Electron Microscopy. The most active bacterial isolate, IRN19, was able to degrade polyethylene film by 26.8?±?3.04% gravimetric weight over 4 weeks. Analysis of 16S rRNA sequence of this isolate revealed 96.97% similarity in sequence to Acinetobacter pitti, which has not previously been identified as a polyethylene-degrading bacterium. Also, most the effective biofilm forming isolate, IRN11, displayed the highest cell mass production (6.29?±?0.06 log cfu/cm²) after growth on LDPE films, showed 98.74% similarity to Sphingobacterium moltivourum.     

Novel Glycopolymers Based on d-Mannose and Methacrylates: Synthesis, Thermal Stability and Biodegradability Testing

This paper presents the synthesis, thermal stability and biodegradability of new d-mannose glycopolymers. These glycopolymers have been obtained by free radical bulk copolymerization of d-mannose based glycomonomer, 1-O-(2′-hydroxy-3′-methacryloyloxypropyl)-2,3:5,6-di-O-isopropylidene-d-mannofuranose (Mm), and respectively d-mannose derived oligomer (Mo) with methyl methacrylate and respectively 2-hydroxypropyl methacrylate. The chemical structures of Mm and Mo have been confirmed via FTIR, ¹H-NMR and HPLC–MS spectroscopy. The copolymerization process has been investigated using differential scanning calorimetry, which allowed calculating the activation energies by applying Kissinger–Akahira–Sunose method. The glycopolymers are thermally stable, fact assessed by TG analysis; their glass transition temperature exceeds 50 °C, so they are part of the glassy class of polymers. The biodegradability of these glycopolymers has been investigated in vitro, using pure cultures of Zymomonas mobilis and Trichoderma reesei. The glycopolymers lose up to 55 % weight in just 14 days of incubation as their surface and composition is altered by colonies of microorganisms that grow on/into them, fact demonstrated using SEM/EDX.     

Development of Regenerated Cellulose/Citric Acid Films with Ionic Liquids

Nowadays, the importance of green and biodegradable plastics as viable substitutes for non-degradable petroleum-based materials is felt more than ever. Regenerated cellulose (RC) as a potential candidate suffers from poor processability and inferior properties, limiting its wide applications. In this study, it is demonstrated that citric acid (CA) enhances physical, mechanical, and thermal properties of RC films, due to RC-citric acid compatibility. 1-ethyl-3-methylimidazolium chloride (EMIMCl) as a green ionic liquid was employed for the processing of RC. The optimum properties in terms of thermal stability, mechanical strength, contact angle, water uptake, and oxygen permeability were achieved at 10 wt% of CA. However, further incorporation of CA adversely affected the film properties. This behaviour was explained by the crosslinking and plasticizing effects of CA. Furthermore, in vitro cytotoxicity test demonstrated that RC/CA films are cytocompatible, suggesting the potential advantage of using these biopolymeric films for biomaterial and biological applications.

     

Preparation of Cellulose Nanocrystals Using an Ionic Liquid

In this paper cellulose nanocrystals were prepared by treating microcrystalline cellulose with 1-butyl-3-methylimidazolium hydrogen sulphate ionic liquid. Cellulose nanocrystals, after separation from ionic liquid, were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), Field emission scanning electron microscopy (FESEM) Transmission Electron Microscope (TEM) and Thermogravimetric analysis. XRD results showed no changes in type of cellulose after the treatment with ionic liquid, however, high crystallinity index was observed in the ionic liquid treated sample. Cellulose nanocrystals, having length around 50–300 nm and diameter around 14–22 nm were observed in the ionic liquid treated sample under FESEM and TEM, and similar patterns of peaks as that of microcrystalline cellulose were observed for cellulose nanocrystals in the FTIR spectra. The thermal stability of the cellulose nanocrystals was measured low as compare to microcrystalline cellulose.     

Introduction of Ionic Liquids as Highly Efficient Plasticizers and Flame Retardants of Cellulose Triacetate Films

Journal of Polymers and the Environment - As a promising biodegradable polymer, cellulose triacetate (CTA) was synthesized and plasticized with ionic liquids to produce flexible biocomposite films...     

Acid Rain in Downtown São Paulo City, Brazil

During the period from July 2002 to June 2004, the chemical characteristics of the rainwater samples collected in downtown São Paulo were investigated. The analysis of 224 wet-only precipitation samples included pH and electrical conductivity, as well as major ions (Na⁺, $ \rm NH^{ + }_{4} During the period from July 2002 to June 2004, the chemical characteristics of the rainwater samples collected in downtown S?o Paulo were investigated. The analysis of 224 wet-only precipitation samples included pH and electrical conductivity, as well as major ions (Na⁺, , K⁺, Ca²⁺, Mg²⁺, Cl⁻, , ) and carboxylic acids (acetic, formic and oxalic) using ion chromatography. The volume weighted mean, VWM, of the anions , and Cl⁻ was, respectively, 20.3, 12.1 and 10.7 μmol l⁻¹. Rainwater in S?o Paulo was acidic, with 55% of the samples exhibiting a pH below 5.6. The VWM of the free H⁺ was 6.27 μmol l⁻¹), corresponding to a pH of 5.20. Ammonia (NH₃), determined as (VWM = 32.8 μmol l⁻¹), was the main acidity neutralizing agent. Considering that the H⁺ ion is the only counter ion produced from the non-sea-salt fraction of the dissociated anions, the contribution of each anion to the free acidity potential has the following profile: (31.1%), (26.0%), CH₃COO⁻ (22.0%), Cl⁻ (13.7%), HCOO⁻ (5.4%) and (1.8%). The precipitation chemistry showed seasonal differences, with higher concentrations of ammonium and calcium during autumn and winter (dry period). The marine contribution was not significant, while the direct vehicular emission showed to be relevant in the ionic composition of precipitation.     

Degradation of a Terephthalate-containing Polyester by Thermophilic Actinomycetes and <Emphasis Type="Italic">Bacillus</Emphasis> Species Derived from Composts

We intended to find thermophilic degraders of terephthalate-containing Biomax^® films. Films in mesh bags were buried in composts (inside temperature: approximately 55–60 °C), resulting in the degradation of them in 2 weeks. Fluorescent microscopy of films recovered from composts showed that microorganisms gradually covered the surface of a film during composting. DGGE analysis of microorganisms on the composted film indicated the presence of Bacillus species as main species (approximately 80% of microbial flora) and actinomycetes (approximately 10–20%) as the second major flora. Isolation of Biomax^®-utilizing bacteria was focused on these two genera: two actinomycetes and one Bacillus species were isolated as pure best degraders from the composted polymer films, which were fragmented into small pieces. All the strains were thermophilic and identified, based on their 16S rDNA analyses. Degradation of polymer films was confirmed by (1) accelerated fragmentation of films in composts, compared with a control (no inoculum) and resultant decrease in molecular weights, (2) growth in a powdered Biomax^® medium, compared with a control without powdered Biomax^®, and (3) production of terephthalate in a powdered Biomax^® medium. In this way, we concluded that these bacteria were useful for degradation of thermostable Biomax^® products.     

Sulfated Polysaccharides from Tunisian Fish Skins: Antioxidant,DNA Damage Protective Effect and Antihypertensive Activities

Sulfated polysaccharides were isolated from two Tunisian fish skins grey triggerfish (Balistes capriscus) (GTSP) and smooth hound (Mustelus mustelus) (SHSP). Their chemical and physical characteristics were investigated. The Analysis of surface morphology by scanning electron microscopy of both sulfated polysaccharides displayed the same shape with netted structure. The antioxidant activities of GTSP and SHSP were evaluated using various in vitro antioxidant assays: 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical-scavenging activity, reducing power, β-carotene bleaching inhibition assay (IC_{50 GTSP} = 0.5 mg mL^?1 and IC_{50 SHSP} = 0.6 mg mL^?1) and DNA nicking assay. Both sulfated polysaccharides exhibited good antioxidant activities. The sulfated polysaccharides showed strong angiotensin I-converting enzyme inhibitory activities (IC_{50 GTSP} = 0.16 mg mL^?1 and IC_{50 SHSP} = 0.18 mg mL^?1). These results revealed that GTSP and SHSP exhibited significant antihypertensive activities. Overall, the results indicated that grey triggerfish and smooth hound skins can be used to generate high value-added products, thus offering a valuable source of bioactive sulfated polysaccharides for application in wide range of biotechnological applications.     

Mechanical Property and Biodegradability of Cast Films Prepared from Blends of Oppositely Charged Biopolymers

Biodegradable cast films of about 50 m thickness were fabricated by blending oppositely charged biopolymers such as anionic starch–chitosan, and cationic starch–pectin. The tensile strength and elongation at break (%) of films were evaluated as well as their capacity to degrade in compost. Films recovered from soil every 48 h showed consistent degradation (weight loss), diminution of the polymers characteristic peak absorbance in the carbohydrate fingerprint region of the FTIR, and changes in the surface morphology via scanning electron microscopy (SEM). Anionic starch–chitosan films had much superior tensile strength and elongation compared to cationic starch–pectin, suggesting that the ionic bonds formed between anionic-starch and positively charged groups in chitosan polymer were much more stable and stronger. Initially, both films lost about 36% weight within 96 h, which also correlated well with the loss in the characteristic absorption peaks in the region of the infrared spectrum typical of biopolymers. The total mineralization of films by microorganisms in compost soil was also measured using respirometric techniques. Though the rate of mineralization differed for two formulations, total mineralization (extent) for both films were achieved within 45 days.