Leachability testing of sludge from street gullies.

Sludge from gullies, on two types of streets with different traffic intensity, was investigated using two recommended EU methods for leachability testing of waste: a two-stage batch test and an up-flow percolation test. The main purpose of this investigation was to gain more knowledge about these leaching test methods to be able to make future decisions on the general applicability of the proposed tests. A number of parameters were determined in the sludge as well as in the eluates obtained from the two leaching tests. These include pH, conductivity, dissolved organic carbon and inorganic ions as chloride ions. A number of metals as Cd, Cr, Cu, Hg, Ni and Zn, were determined by inductive coupled plasmamass spectrometry and organic compounds were screened by high performance liquid chromatography-diode array UV detection and gas chromatography-mass spectrometry. It was found that the concentrations of metals and organic compounds in the sludge were several orders of magnitudes higher than the actual eluate concentrations. For all metals the concentrations were well below the proposed limit values for non-hazardous waste included in the Council decision document 2003/33/EC. Generally, concentrations obtained in batch test were equal or higher than from percolation tests. The repeatability of the percolation and the batch test were in average 28 and 17%, respectively.     

铅冶炼烟尘的物性分析及浸出性研究

采用XRF、XRD、激光粒度分析、DTA-TG、FTIR以及SEM-EDS等技术,对某铅冶炼厂烟尘（简称烟尘）进行了物性分析,并采用稀硫酸对烟尘进行了浸出性研究。分析结果表明：烟尘所含主要元素为Pb,Zn,Cd,Cl,S,As;烟尘是氧化物、硫酸盐、硅酸盐、硫化物和砷化物等物质的混合物,主要物相为ZnO,PbO,PbSO₄,CdO,CdS;烟尘颗粒大小不一,形状各异,多呈相互黏结或包裹状。实验结果表明：在ρ（硫酸）=120 g/L、浸出时间30 min、液固比（稀硫酸体积（mL）与烟尘质量（g）之比）20∶1、浸出温度60 ℃的条件下,Pb,Zn,Cd,As,Cl的浸出率分别达到0.16%,98.95%,49.36%,89.12%,99.31%。     

Leachability and metal-binding capacity in ageing landfill material

In order to study the stability of landfilled heavy metals, landfill material from a combined household and industrial waste landfill was aerated for 14 months to simulate the natural ageing processes as air slowly begins to penetrate the landfill mass. During aeration, the pH of the landfill material decreased from around 8.6 to 8.1 and the carbon content also decreased. In order to investigate the possible fate of metals in ageing landfills, a four-stage sequential extraction technique was applied. The ability of the materials to bind metal ions by electrostatic attractions and to form stronger complexes was studied separately. The amount of exchangeable cations, the capacity to bind metal ions by electrostatic attraction and the capacity of the landfill material to complex copper ions were increased by the aeration process. However, results from the sequential analysis showed an increased solubility of sulphur and some metals (Cd, Co, Cu, Ni and Zn). Equilibrium speciation models (Medusa) indicated that the organic matter deposit had a significant capacity to bind metal ions provided that pH was sufficiently high. However, as carbonates are consumed over time, the risk for metal mobility increases. Therefore, the landfills can become an environmental risk, depending on variations in the solubility of metal ions due to changes in pH, redox status and the availability of organic material.     

Leachability of heavy metals from copper blasting grit waste

This investigation presents the results of leaching tests, using the multiple-batch procedure, on cadmium, zinc, copper, lead, and chromium from copper blasting grit waste generated from a shipbuilding and repair company in Bahrain. The leaching test results have demonstrated that the metals tested were generally released in low concentrations except for copper and zinc. Metal leachability appeared to be dependent upon the pH and composition of the leaching medium.     

Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

Soil reinforcement with recycled carpet wastes.

A root or fibre-reinforced soil behaves as a composite material in which fibres of relatively high tensile strength are embedded in a matrix of relatively plastic soil. Shear stresses in the soil mobilize tensile resistance in the fibres, which in turn impart greater strength to the soil. A research project has been undertaken to study the influence of synthetic fibrous materials for improving the strength characteristics of a fine sandy soil. One of the main objectives of the project is to explore the conversion of fibrous carpet waste into a value-added product for soil reinforcement. Drained triaxial tests were conducted on specimens, which were prepared in a cylindrical mould and compacted at their optimum water contents. The main test variables included the aspect ratio and the weight percentage of the fibrous strips. The results clearly show that fibrous inclusions derived from carpet wastes improve the shear strength of silty sands. A model developed to simulate the effect of the fibrous inclusions accurately predicts the influence of strip content, aspect ratio and confining pressure on the shear strength of reinforced sand.     

赤泥中重金属元素的浸出性与结合形态

采用等离子体质谱仪分析了拜耳法赤泥(BRM)和烧结法赤泥(SRM)中Cr,Ni,Cu,Zn,As,Cd,Cs,Pb等8种重金属元素的含量。采用逐级提取的方法分析了BRM和SRM中8种重金属元素的浸出情况和形态分布差异。实验结果表明:SRM中水溶态As的质量浓度达到17.3μg/L,BRM和SRM中可交换态Cr的质量浓度均在2 300μg/L以上,对水环境可能存在潜在危害;两种赤泥中不同形态重金属的浸出率有较大差异,SRM中Ni和BRM中Zn的总浸出率分别在60%和50%以上。     

Beneficiation of graphite fines from moulding factory wastes.

As the costs of waste disposal increase, more attention is being placed upon the re-use and recycling of valuable minerals contained within the waste streams. In this article, the waste streams from a moulding factory were treated by physical methods to obtain a re-usable graphite fraction. Multi-gravity separators (MGS) and shaking tables (ST) are being used in coal processing and heavy minerals beneficiation. In the present study, the possibility of using an MGS and ST to separate graphite from moulding sand was analysed as part of such investigations. The effects of changes in different process variables on the concentrate sand content and graphite recovery values were studied. Several parameters, thought to have an effect on the separation were tested. After the ST experiments, a graphite concentrate was obtained having 4.5% sand content with 60.8% recovery. After the investigations carried out by MGS, a graphite concentrate was obtained having 0.95% sand content with 68.0% recovery. The results demonstrated that recovered graphite fractions can be re-used in the factory, thus reducing the quantity of waste and costs.     

Leachability of automotive shredder residues burned in a fluidized bed system

This paper presents the results of the study of a combustible fraction of automotive shredder residues (CASRs) and the corresponding ashes generated by combustion on a fluidized bed pilot with the aim to understand the influence of thermal treatment regarding properties for final disposal, such as landfilling. The chemical composition was evaluated and the leachability behaviour of ashes and CASR was investigated using the three more commonly used tests: the European Standard EN 12457, the US TCLP-EPA 1311 and the Dutch availability test EA NEN 7371. Different results were obtained depending on the specific conditions of the methods employed. It was found that both the CASR and the ashes contained large amounts of toxic metals and other undesirable elements, such as Cl and S. For the CASR, in addition to the leachability of organic matter above the limit set for hazardous materials, the release of heavy metals, either under alkaline and acidic conditions was significant, revealing the serious risks associated to the landfilling practices still being undertaken worldwide. Release of organic matter from ashes was insignificant, but solubility of sulphates increased and chlorides exceed the hazardous limits in the case of fly ashes. Toxic metals were found to leach from the ashes only under acidic conditions, except Pb and Cu which also leached from finer ashes at alkaline pH. Cr also leached from ashes at alkaline pH values. Both the Dutch availability and TCLP revealed much higher leaching intensities than the European Standard due to the acidity of leachants. However, it was found that ashes may be more resistant to acidification because they exhibit much higher acid neutralization capacity (ANC) than the untreated CASR. The study undertaken shows that thermal valorisation of the combustible fraction of ASR may avoid the risks associated with their landfilling; however, care has to be taken with the ashes because they also behave as hazardous residues. Although, the mass reduction provided by thermal treatment may make landfilling less expensive, a more profitable reutilization of the ashes should be developed.     

Development of a testing method for asbestos fibers in treated materials of asbestos containing wastes by transmission electron microscopy

Appropriate treatment of asbestos-containing wastes is a significant problem. In Japan, the inertization of asbestos-containing wastes based on new treatment processes approved by the Minister of the Environment is promoted. A highly sensitive method for testing asbestos fibers in inertized materials is required so that these processes can be approved. We developed a method in which fibers from milled treated materials are extracted in water by shaking, and are counted and identified by transmission electron microscopy. Evaluation of this method by using asbestos standards and simulated slag samples confirmed that the quantitation limits are a few million fibers per gram and a few μg/g in a sample of 50 mg per filter. We used this method to assay asbestos fibers in slag samples produced by high-temperature melting of asbestos-containing wastes. Fiber concentrations were below the quantitation limit in all samples, and total fiber concentrations were determined as 47–170 × 10^?6 f/g. Because the evaluation of treated materials by TEM is difficult owing to the limited amount of sample observable, this testing method should be used in conjunction with bulk analytical methods for sure evaluation of treated materials.     

Characteristics of healthcare wastes

A comprehensive understanding of the quantities and characteristics of the material that needs to be managed is one of the most basic steps in the development of a plan for solid waste management. In this case, the material under consideration is the solid waste generated in healthcare facilities, also known as healthcare waste. Unfortunately, limited reliable information is available in the open literature on the quantities and characteristics of the various types of wastes that are generated in healthcare facilities. Thus, sound management of these wastes, particularly in developing countries, often is problematic. This article provides information on the quantities and properties of healthcare wastes in various types of facilities located in developing countries, as well as in some industrialized countries. Most of the information has been obtained from the open literature, although some information has been collected by the authors and from reports available to the authors. Only data collected within approximately the last 15 years and using prescribed methodologies are presented. The range of hospital waste generation (both infectious and mixed solid waste fractions) varies from 0.016 to 3.23kg/bed-day. The relatively wide variation is due to the fact that some of the facilities surveyed in Ulaanbaatar include out-patient services and district health clinics; these facilities essentially provide very basic services and thus the quantities of waste generated are relatively small. On the other hand, the reported amount of infectious (clinical, yellow bag) waste varied from 0.01 to 0.65kg/bed-day. The characteristics of the components of healthcare wastes, such as the bulk density and the calorific value, have substantial variability. This literature review and the associated attempt at a comparative analysis point to the need for worldwide consensus on the terms and characteristics that describe wastes from healthcare facilities. Such a consensus would greatly facilitate comparative analyses among different facilities, studies and countries.     

Leachability of V and Cr from LD-Slag/Portland Cement stabilised sulphide soil

The objectives of this study were to improve the mechanical stability of a sulphide soil with additives of an industrial waste product (LD-Slag) and Portland Cement. The criterion of using LD-Slag was if it could be done in an environmentally proper way. Sequential Leaching Tests were performed on monolithic LD-Slag/Portland Cement stabilised sulphide soil samples in order to register the leachability and pollution potentials. Different pH and Eh conditions were established in these tests in order to control the leachability of Na, K, Ca and Mg, which are important during cementation processes inside as well as outside an inforced monolith, and the leachability of V, which is regarded as a pollutant. The contents of Cr and V of pure LD-Slag, monolithic samples and leachates were compared with Canadian and Finnish Maximum Containment Level standards. The investigation showed that acidic conditions will increase the leachability of V. An acidic environment will even change the physical properties of a monolith. However, acidic conditions are not likely to occur in an in-situ anaerobic sulphide soil.     

In-vessel composting of household wastes

The process of composting has been studied using five different types of reactors, each simulating a different condition for the formation of compost; one of which was designed as a dynamic complete-mix type household compost reactor. A lab-scale study was conducted first using the compost accelerators culture (Trichoderma viridae, Trichoderma harzianum, Trichorus spirallis, Aspergillus sp., Paecilomyces fusisporus, Chaetomium globosum) grown on jowar (Sorghum vulgare) grains as the inoculum mixed with cow-dung slurry, and then by using the mulch/compost formed in the respective reactors as the inoculum. The reactors were loaded with raw as well as cooked vegetable waste for a period of 4 weeks and then the mulch formed was allowed to maturate. The mulch was analysed at various stages for the compost and other environmental parameters. The compost from the designed aerobic reactor provides good humus to build up a poor physical soil and some basic plant nutrients. This proves to be an efficient, eco-friendly, cost-effective, and nuisance-free solution for the management of household solid wastes.     

Biodegradation and flushing of MBT wastes

Mechanical–biological treatment (MBT) processes are increasingly being adopted as a means of diverting biodegradable municipal waste (BMW) from landfill, for example to comply with the EU Landfill Directive. However, there is considerable uncertainty concerning the residual pollution potential of such wastes. This paper presents the results of laboratory experiments on two different MBT waste residues, carried out to investigate the remaining potential for the generation of greenhouse gases and the flushing of contaminants from these materials when landfilled. The potential for gas generation was found to be between 8% and 20% of that for raw MSW. Pretreatment of the waste reduced the potential for the release of organic carbon, ammoniacal nitrogen, and heavy metal contents into the leachate; and reduced the residual carbon remaining in the waste after final degradation from ～320 g/kg dry matter for raw MSW to between 183 and 195 g/kg dry matter for the MBT wastes.     

2020年危险废物市场分析

危险废物处理与政策、法规、标准、技术、市场等影响因素关系密切。对2019年以来我国出台的危险废物管理政策法规、管理措施和标准规范情况进行梳理,对危险废物产生和利用处置情况进行对比分析,对危险废物利用处置技术进展、价格变动和市场投资趋势等进行概述,对环境违法案件舆情及突发事件等因素对危险废物市场影响进行分析,综合运用类比、归纳和演绎等方法,对2020年危险废物市场进行预测分析。     

Accelerated carbonation treatment of industrial wastes

The disposal of industrial waste presents major logistical, financial and environmental issues. Technologies that can reduce the hazardous properties of wastes are urgently required. In the present work, a number of industrial wastes arising from the cement, metallurgical, paper, waste disposal and energy industries were treated with accelerated carbonation. In this process carbonation was effected by exposing the waste to pure carbon dioxide gas. The paper and cement wastes chemically combined with up to 25% by weight of gas. The reactivity of the wastes to carbon dioxide was controlled by their constituent minerals, and not by their elemental composition, as previously postulated. Similarly, microstructural alteration upon carbonation was primarily influenced by mineralogy. Many of the thermal wastes tested were classified as hazardous, based upon regulated metal content and pH. Treatment by accelerated carbonation reduced the leaching of certain metals, aiding the disposal of many as stable non-reactive wastes. Significant volumes of carbon dioxide were sequestrated into the accelerated carbonated treated wastes.     

包装垃圾的分类与回收利用

包装垃圾是由废弃的包装物产生的固体垃圾,约占我国城市生活垃圾的1/3,虽然政府进行了必要回收,但仍有1/3以上的塑料、玻璃等包装物没能被有效回收利用,成了填埋场的主要填埋物,造成了环境污染和土地、石油等不可再生资源大量浪费。从回收利用和源头减量两方面提出包装垃圾的应对,一是对包装垃圾按来源、成分等进行详细分类,并建议回收处置方法;二是从制定行业政策方面来减少过度包装和扶持再生资源行业健康发展,有效处置包装垃圾等可再生资源。     

Energy from gasification of solid wastes

Gasification technology is by no means new: in the 1850s, most of the city of London was illuminated by "town gas" produced from the gasification of coal. Nowadays, gasification is the main technology for biomass conversion to energy and an attractive alternative for the thermal treatment of solid waste. The number of different uses of gas shows the flexibility of gasification and therefore allows it to be integrated with several industrial processes, as well as power generation systems. The use of a waste-biomass energy production system in a rural community is very interesting too. This paper describes the current state of gasification technology, energy recovery systems, pre-treatments and prospective in syngas use with particular attention to the different process cycles and environmental impacts of solid wastes gasification.