北京市居民PET饮料瓶的消费及回收行为研究

2010年,中国成为世界上PET饮料瓶使用量最大的国家,但中国目前缺乏正规、完整的废PET饮料瓶回收系统,导致了严重的社会与环境问题.因此,采用街头访问的方式,对北京市PET饮料瓶的回收情况展开调研.结果显示,消费后的废PET饮料瓶,44％被消费者存放在家里以卖钱,56％被消费者直接扔进垃圾桶.通过拾荒者、流动回收人员等回收者的回收行为,北京几乎所有的废PET饮料瓶都得到了回收,其中90％是由非正规的回收者回收的.回收后的废PET饮料瓶绝大部分都被小型的、非正规的、没有环境污染防治设施的小工厂使用.     

Recovery and distribution of incinerated aluminum packaging waste

A study was performed into relations between physical properties of aluminum packaging waste and the corresponding aluminum scraps in bottom ash from three typical incineration processes. First, Dutch municipal solid waste incineration (MSWI) bottom ash was analyzed for the identifiable beverage can alloy scraps in the +2mm size ranges using chemical detection and X-ray fluorescence. Second, laboratory-scale pot furnace tests were conducted to investigate the relations between aluminum packaging in base household waste and the corresponding metal recovery rates. The representative packaging wastes include beverage cans, foil containers and thin foils. Third, small samples of aluminum packaging waste were incinerated in a high-temperature oven to determine leading factors influencing metal recovery rates. Packaging properties, combustion conditions, presence of magnesium and some specific contaminants commonly found in household waste were investigated independently in the high-temperature oven. In 2007, the bottom ash (+2mm fraction) from the AEB MSWI plant was estimated to be enriched by 0.1 wt.% of aluminum beverage cans scrap. Extrapolating from this number, the recovery potential of all eleven MSWI plants in the Netherlands is estimated at 720 ton of aluminum cans scrap. More than 85 wt.% of this estimate would end up in +6mm size fractions and were amenable for efficient recycling. The pot furnace tests showed that the average recovery rate of metallic aluminum typically decreases from beverage cans (93 wt.%) to foil containers (85 wt.%) to thin foils (77 wt.%). The oven tests showed that in order of decreasing impact the main factors promoting metallic aluminum losses are the packaging type, combustion temperature, residence time and salt contamination. To a lesser degree magnesium as alloying element, smaller packaging size and basic contaminations may also promote losses.     

Improvement of Waste Recycling in PET Fiber Production

Production of polyethylene teraphtalate (PET) fiber in the world is increasing every year and reached to an amount of about 20 million tons a year in 2001. The wastes occur in the production of PET fiber in the amount of about 3–5% of total production. The PET does not degrade for a long time in nature. Since PET is a derivative of petroleum, the wastes of PET are valuable and must be recycled. One of the recycling method of PET wastes is re-melting. Thus, various properties of the PET wastes were improved using the re-melting method by employing an extruder manufactured for the work. Degradation during re-melting decreases the properties of the final product. The results indicate that the properties of recycled PET wastes can be monitored by designing the parameters of the extruder. Also, the further degradation of the material can be prevented and the recycling costs are minimized.     

Set-up of a bottle sorting and recycling plant

An initial operation in Paris has made it possible to gauge the effectiveness of a selective pick-up of non-returnable bottles according to the following criteria: willingness of the people of Paris, the danger of breakage when collecting in special containers and the technical and economic aspects of the implementation of an industrial-scale sorting machine. In view of the positive results of this experiment, the following system has been installed:

• •• Containers have been placed on the public walkway, the drop of bottles being at the most 1 m.
• •• The bottles are transported to a plant with an annual capacity of 35,000 tons of glass or 20 million bottles.
• •• Following a first hand-sorting process, the bottles are washed and sorted in an automatic sorter.

Currently two sizes of each of three categories of wine bottles are recovered. Rejected bottles are sent to the scrap pile and shipped as cullett to glass factories to be melted down.This design constitute a complete system which enables us to recover not only glass but bottles which are intact and thus represent a higher level of energy savings.     

Depolymerization of Waste PET with Phosphoric Acid–Modified Silica Gel Under Microwave Irradiation

Chemical recycling of waste poly(ethylene terephthalate) (PET) using phosphoric acid–modified silica gel as a solid catalyst is reported. Advantageously, microwave irradiation was used to progress the depolymerization of PET. In this study, depolymerization of PET with a small amount of water is suggested as a suitable method. The depolymerized product, terephthalic acid was obtained and assigned by ¹H NMR and FT-IR spectroscopy. Finally, over 90 % conversion to terephthalic acid was achieved when waste plastic bottles were treated with the method. This results confirm the importance of the microwave power technique as a promising recycling method for plastic bottles made from PET, resulting in monomer recovery in addition to substantial energy saving.     

Use of plastic waste (poly-ethylene terephthalate) in asphalt concrete mixture as aggregate replacement.

One of the environmental issues in most regions of Iran is the large number of bottles made from poly-ethylene terephthalate (PET) deposited in domestic wastes and landfills. Due to the high volume of these bottles, more than 1 million m3 landfill space is needed for disposal every year. The purpose of this experimental study was to investigate the possibility of using PET waste in asphalt concrete mixes as aggregate replacement (Plastiphalt) to reduce the environmental effects of PET disposal. For this purpose the mechanical properties of plastiphalt mixes were compared with control samples. This study focused on the parameters of Marshall stability, flow, Marshall quotient (stability-to-flow ratio) and density. The waste PET used in this study was in the form of granules of about 3 mm diameter which would replace (by volume) a portion of the mineral coarse aggregates of an equal size (2.36-4.75 mm). In all prepared mixes the determined 6.6% optimum bitumen content was used. In this investigation, five different percentages of coarse aggregate replacement were used. The results showed that the aggregate replacement of 20% by volume with PET granules would result in a reduction of 2.8% in bulk compacted mix density. The value of flow in the plastiphalt mix was lower than that of the control samples. The results also showed that when PET was used as partial aggregate replacement, the corresponding Marshall stability and Marshall quotient were almost the same as for the control samples. According to most of specification requirement, these results introduce an asphalt mix that has properties that makes it suitable for practical use and furthermore, the recycling of PET for asphalt concrete roads helps alleviate an environmental problem and saves energy.     

Feasibility study for thermal treatment of solid tire wastes in Bangladesh by using pyrolysis technology

In this study on the basis of lab data and available resources in Bangladesh, feasibility study has been carried out for pyrolysis process converting solid tire wastes into pyrolysis oils, solid char and gases. The process considered for detailed analysis was fixed-bed fire-tube heating pyrolysis reactor system. The comparative techno-economic assessment was carried out in US$ for three different sizes plants: medium commercial scale (144 tons/day), small commercial scale (36 tons/day), pilot scale (3.6 tons/day). The assessment showed that medium commercial scale plant was economically feasible, with the lowest unit production cost than small commercial and pilot scale plants for the production of crude pyrolysis oil that could be used as boiler fuel oil and for the production of upgraded liquid-products.     

Classification of in-flight catering wastes in Egypt air flights and its potential as energy source (chemical approach)

Waste to energy conversion is based on the classification of waste. In-flight catering wastes resulting from Egypt Airlines economy class passengers were classified. The solid waste stream generated contains plastic, paper, left-over waste food and aluminum. The type of meal served varies according to the period of flight and so the quantity and content of the waste stream. It was found that the waste generation rate varied from 61.3 to 265 g according to the meal type. Breakfast snack meal generates the highest weight of waste which recorded an average of 265 g. Plastic waste generated varied from 39.6% to 64.6% by weight for the various types of meals served. A total amount of 725 tons were generated annually from organic waste (paper, plastic and food waste) among which a non combustible 39.4 tons of aluminum. The calorific value for each generated item is calculated and the total energy potential reached up to 14.3 TJ annually.     

Study of the effect of political measures on the citizen participation rate in recycling and on the environmental load reduction

Obtaining the cooperation of citizens to participate in separate waste collection is essential to create a recycling-oriented society. In this research, the degree of change in the citizen participation rate, which occurs when the contents of political measures such as the raising of awareness, provision of information, and the conditions of collection services were changed, was estimated together with the effect on the reduction in environmental load. A questionnaire survey was conducted, targeted at residents of Itabashi Ward, while logistic regression analyses were also conducted to create predictive models for recycling behavior, and sensitivity analyses of the models were carried out to estimate the increase in citizen participation rate achievable through the implementation of various political measures. It was found that the effect of "thorough perception of information" was the largest, followed by "minimization of evaluation of trouble" and "thorough perception of efficacy of measures." The effect of the improvement in the citizen participation rate on the reduction in environmental load was also evaluated quantitatively by life cycle inventory analyses. It was indicated that "maximization of perception of information" had the greatest effect. However, the reduction effect with "paper packs" and "PET bottles" was relatively small compared with that of "bottles/cans."     

Recycling and reuse of industrial wastes in Taiwan

Eighteen million metric tons of industrial wastes are produced every year in Taiwan. In order to properly handle the industrial wastes, the Taiwan Environmental Protection Administration (Taiwan EPA) has set up strategic programs that include establishment of storage, treatment, and final disposal systems, establishment of a management center for industrial wastes, and promotion of recycling and reuse of industrial wastes. The Taiwan EPA has been actively promoting the recycling and reuse of industrial wastes over the years. In July 1995 the Taiwan EPA amended and promulgated the Criteria for the Industrial Waste Storage, Collection and Processing Facility, July, 1995 that added articles related to general industrial waste recycling and reuse. In June 1996 the Taiwan EPA promulgated the Non-listed General Industrial Waste Reuse Application Procedures, June, 1996, followed by the Regulations Governing the Permitting of Hazardous Industrial Waste Reuse, June 1996, setting up a full regulatory framework for governing industrial waste reuse. To broaden the recycling and reuse of general industrial wastes, the Taiwan EPA has listed 14 industrial waste items for recycling and reuse, including waste paper, waste iron, coal ash, tempered high furnace bricks (cinder), high furnace bricks (cinder), furnace transfer bricks (cinder), sweetening dregs, wood (whole/part), glass (whole/part), bleaching earth, ceramics (pottery, brick, tile and cast sand), individual metal scraps (copper, zinc, aluminum and tin), distillery grain (dregs) and plastics. As of June 1999, 99 applications for reuse of industrial wastes had been approved with 1.97 million metric tons of industrial wastes being reused.     

Nature and extent of unauthorized waste dump sites in and around Bangalore city

Journal of Material Cycles and Waste Management - Bangalore city generates around 3600 tons/day of solid waste and a major constituent is organic (>70 %). The quantum of wastes...     

Evaluation of Poly(ethylene-terephthalate) Products of Chemical Recycling by Differential Scanning Calorimetry

Poly (ethylene-terephthalate), (PET) bottles waste was chemically recycled by glycolysis and hydrolysis. The depolymerization processes were carried out in different time intervals from 5 to 360 min, in two different molar ratios of PET/EG, 1:5 and 1:18 and at different temperatures. The PET glycolysis leads to formation of bis(2-hydroxy-ethyl)terephthalate (BHET) monomer and PET oligomers with hydroxyl and carboxyl end groups while PET hydrolysis is followed by formation of monomers terephthalic acid (TPA) and ethylene glycol (EG). Fractions of monomers and oligomers were further characterized by FTIR spectroscopy and by differential scanning calorimetry (DSC). The results show that DSC is successful method to describe the different structures of oligomers formed during chemical recycling of PET.     

Valorization of post-consumer waste plastic in cementitious concrete composites

The sheer amount of disposable bottles being produced nowadays makes it imperative to identify alternative procedures for recycling them since they are non-biodegradable. This paper describes an innovative use of consumed plastic bottle waste as sand-substitution aggregate within composite materials for building application. Particularly, bottles made of polyethylene terephthalate (PET) have been used as partial and complete substitutes for sand in concrete composites. Various volume fractions of sand varying from 2% to 100% were substituted by the same volume of granulated plastic, and various sizes of PET aggregates were used. The bulk density and mechanical characteristics of the composites produced were evaluated. To study the relationship between mechanical properties and composite microstructure, scanning electron microscopy technique was employed. The results presented show that substituting sand at a level below 50% by volume with granulated PET, whose upper granular limit equals 5mm, affects neither the compressive strength nor the flexural strength of composites. This study demonstrates that plastic bottles shredded into small PET particles may be used successfully as sand-substitution aggregates in cementitious concrete composites. These new composites would appear to offer an attractive low-cost material with consistent properties; moreover, they would help in resolving some of the solid waste problems created by plastics production and in saving energy.     

The consumption and recycling collection system of PET bottles: A case study of Beijing,China

After studying the recycling collection system of polyethylene terephthalate (PET) bottles worldwide, the authors conducted an intercept survey in Beijing. Two separate questionnaires were issued, one questionnaire to PET bottle consumers and one to PET bottle recyclers. In this study, consumers are defined as people that consume PET-bottled beverages in their daily life. Recyclers were defined as those involved in the collection and recycling of PET bottles. These include scavengers, itinerant waste buyers, small community waste-buying depots, medium/large redemption depots, and recycling companies. In total, 580 surveys were completed, including 461 by consumers and 119 by recyclers. The authors found that consumption of PET bottles in Beijing was nearly 100,000 tonnes in 2012. Age, occupation, gender, and education were identified as significant factors linked to PET-bottled beverage consumption, while income was not a significant factor. 90% Of post-consumed PET bottles were collected by informal collectors (i.e., scavengers and itinerant waste buyers). The survey also found that nearly all PET bottles were reprocessed by small factories that were not designed with pollution control equipment, which allows them to offer higher prices for waste recyclable bottles. As Beijing is trying to build a formal recycling collection system for recyclables, subsidies should be given to the formal recycling sector rather than being charged land use fees, and attention should also be given to informal recyclers that make their living from the collection of recyclables. Informal and formal sectors may work together by employing the scavengers and itinerant waste buyers for the formal sectors. In addition to the recycling of PET bottles, concern should also be allocated to reduce consumption, especially among young people, as they, compared to other groups, have a stronger demand for PET-bottled beverages and will be the main body of society.     

Recent trends in recycling activities and waste management in Japan

Japan's basic approach to municipal solid waste (MSW) is (1) waste reduction, (2) promotion of recycling, (3) volume reduction by intermediate treatment, and (4) environmentally sound final disposal. A brief history of legislative trends in waste management is given as background for current waste management and recycling activities. The material recovery rate for MSW collected by local municipalities was only 5.6% in 1996. More than half of MSW, on a volume basis, consists of containers and packages, while great amounts of landfill space are also taken up by bulky wastes such as electric appliances. Therefore, in order to promote recycling and decrease landfill waste, Japan is targeting containers, packages, and electric appliances. A law promoting separate collection and recycling of containers and packages (Packaging Waste Recycling Law) and a law requiring the recycling of specific home electric appliances into new products (Home Electric Appliance Recycling Law) were introduced in June 1995 and June 1998, respectively. These laws are in line with the OECD policy Extended Producer Responsibility (EPR). Received: September 16, 1998 / Accepted: March 10, 1999     

The current situation of solid waste generation and its environmental contamination in China

In China, controlling environmental pollution resulting from solid waste (SW) and hazardous waste (HW) has become one of the most pressing tasks in the field of environmental engineering. It is reported that the annual generation of industrial solid waste (ISW) in China exceeded 0.6 billion tons in the 1990s, and is increasing every year. Although ISW management has been strengthened in recent years, about 40% of SW is put in uncontrolled landfill without appropriate treatment. According to statistics from the national Environmental Protection Agency, the cumulative ISW uncontrolled landfill in China had reached 6.6 billion tons by the end of 1995, occupying around 55 000 hectares of land. Although some major uncontrolled landfills were constructed, nonetheless groundwater contamination resulted from the use of low-standard liners and poor management. Furthermore, about 20 million tons of ISW was discharged into the environment illegally, and a third of this waste was discharged directly into water bodies, making ISW one of the greatest pollution sources for surface water and ground water. Environmental pollution accidents resulting from SW occur about 100 times a year in China, and environmental issues frequently arise because of ISW pollution. The practices of SW management, treatment, and disposal started relatively late in China, and for a long time the management of SW pollution has received little attention compared with water and air pollution management. China faces problems such as the insufficiency of management laws and regulations, insufficient investment, inadequate treatment and disposal technology, and a lack of qualified technicians. At present, most treatment and disposal technology cannot meet the requests for solid waste pollution control. In order to protect, restore, and improve environmental quality in China and to realize sustainable development, the safe management and disposal of solid and hazardous wastes is a pressing challenge. In recent years, much attention has been paid to SW management in China, and investment to develop management and treatment technologies has increased. In 1995, the Law for Solid Waste Pollution Protection was issued, and work on solid waste treatment and disposal began to be legally managed. SW treatment and disposal facilities have been constructed, and now operate in some large and medium-sized cities. In particular, rapid improvements have been seen in ISW recycling, collection, and disposal of municipal solid waste and regional HW management. All the figures in this paper are from 1995, and represent the situation in China in that year. Received: April 18, 2000 / Accepted: May 15, 2000     

Evaluation of metals in the residue of paper sludge after recovery of pulp components using an ionic liquid

The quantity of sludge produced by the paper industry in Japan in 2011 was estimated to be 27.91 million tons wet weight. This amount is the third largest among all industrial wastes. To explore ways of reusing recovered paper pulp and safely disposing of the residue, we investigated the distribution of metals in the process of recovery of pulp from two types of paper sludge using an ionic liquid. 32 and 46 % of pulp from paper sludge A and B was recovered using ionic liquid, respectively; the resultant weight reduction of the solid mass was comparable to that of incineration. There were virtually no heavy metals but aluminum in the recovered pulp, which makes its reuse viable at present. The characteristics of the metals in the residues differed according to the treatment used and properties of the paper sludge. Copper accounted for ~10 % in the ionic liquid used for recovery of pulp from the paper sludges. This suggests that [bmIm]Cl has the potential to dissolve a specific amount of copper compared to other metals.     

Quantitative mineralogical composition of complex mineral wastes – Contribution of the Rietveld method

The objective of the work presented in this paper is the quantitative determination of the mineral composition of two complex mineral wastes: a sewage sludge ash (SSA) and a municipal solid waste incineration fly ash (MSWIFA). The mineral compositions were determined by two different methods: the first based on calculation using the qualitative mineralogical composition of the waste combined with physicochemical analyses; the second the Rietveld method, which uses only X-ray diffraction patterns. The results obtained are coherent, showing that it is possible to quantify the mineral compositions of complex mineral waste with such methods.The apparent simplicity of the Rietveld method (due principally to the availability of software packages implementing the method) facilitates its use. However, care should be taken since the crystal structure analysis based on powder diffraction data needs experience and a thorough understanding of crystallography. So the use of another, complementary, method such as the first one used in this study, may sometimes be needed to confirm the results.     

Developing a master plan for hospital solid waste management: a case study

Disposal of about 1750tons of solid wastes per day is the result of a rapid population growth in the province of Khuzestan in the south west of Iran. Most of these wastes, especially hospital solid wastes which have contributed to the pollution of the environment in the study area, are not properly managed considering environmental standards and regulations. In this paper, the framework of a master plan for managing hospital solid wastes is proposed considering different criteria which are usually used for evaluating the pollution of hospital solid waste loads. The effectiveness of the management schemes is also evaluated. In order to rank the hospitals and determine the share of each hospital in the total hospital solid waste pollution load, a multiple criteria decision making technique, namely analytical hierarchy process (AHP), is used. A set of projects are proposed for solid waste pollution control and reduction in the proposed framework. It is partially applied for hospital solid waste management in the province of Khuzestan, Iran. The results have shown that the hospitals located near the capital city of the province, Ahvaz, produce more than 43% of the total hospital solid waste pollution load of the province. The results have also shown the importance of improving management techniques rather than building new facilities. The proposed methodology is used to formulate a master plan for hospital solid waste management.     

Biopolymers in the Existing Postconsumer Plastics Recycling Stream

The existing plastic bottle reclaiming industry has working technology, satisfied customers, raw material, and investors. Adding new materials to the current mix requires satisfying all four needs for those materials. Rigid plastic container recycling focuses on high-density polyethylene (HDPE) and polyethylene terephthalate (PET) bottles, the overwhelming percentage of bottles sold in North America. Bottles of other resins, including polyvinyl chloride (PVC), polypropylene and biopolymers, lack critical mass necessary for independent reclamation. To be mechanically recycled, biopolymers must be either completely fungible with existing recycled resins or be available in sufficient quantity to achieve the needed critical mass. So far, biopolymer volume projections are not encouraging. Biopolymers, like all minor bottle resins, must pay their own way in sorting and processing without subsidy from PET and HDPE recycling. Based on limited data, some biopolymers may have little effect on recycled HDPE performance, but will represent a yields loss and added economic burden at some level of occurrence. Biopolymers have not been shown to be compatible with PET and likely will represent performance problems and economic burdens at even low levels of occurrence. Applications for biopolymers should be carefully selected so as to not interfere with currently recycled materials unless critical mass can be achieved quickly.