Prediction of Total Sediment Load in Sand‐Bed Rivers in Korea Using Lateral Distribution Method

A new method for numerically predicting the total sediment load in a river is proposed. The method can be used to predict the total sediment load with information on channel geometry and slope, flow, and bed materials. The conventional method uses a 1D approach that assumes the channel has a wide rectangular shape. However, the proposed method computes depth‐averaged velocity over the width and predicts the total sediment load based on the flow computations. The new method, therefore, is expected to predict better if the flow changes significantly in the lateral direction. The proposed method was applied to three large sand‐bed rivers in Korea, where information is available regarding suspended sediment. Five formulas were tested of use in making total sediment load computations, namely Engelund‐Hansen's, Ackers‐White's, Yang's, Brownlie's, and Karim's formulas. The predicted total sediment loads are compared not only with measured data but also with results calculated using the 1D approach. Discrepancy ratios between the predicted and measured total sediment loads are given and the results are discussed.     

ESTIMATING NUTRIENT AND SEDIMENT THRESHOLD CRITERIA FOR BIOLOGICAL IMPAIRMENT IN PENNSYLVANIA WATERSHEDS1

ABSTRACT: This study employs a simple nonlinear statistical approach to establish nitrogen, phosphorus, and sediment concentration and unit area load thresholds to aid in the evaluation of aquatic biological health of watersheds within the state of Pennsylvania. Flow, nitrogen and phosphorus species, sediment, basin area, land cover, and biological assessment data were assembled for 29 Pennsylvania watersheds. For each watershed, rating curves depicting flow versus load relationships were developed using the U.S. Environmental Protection Agency's (USEPA's) storage and retrieval database (STORET) flow and concentration data, then applied to daily flow data obtained from U.S. Geological Survey (USGS) daily flow gauging stations to estimate daily load between 1989 and 1999. The load estimates and concentration data were then sorted into six sets of data: mean annual unit area nitrogen, phosphorus, and sediment loads; and average nitrogen, phosphorus, and sediment concentrations. Results of Mann‐Whitney tests conducted on each of the six datasets indicate that there is a statistically significant difference between the concentrations and unit area loads of nitrogen, phosphorus, and sediment in impaired and unimpaired watersheds. Concentration thresholds, calculated as the midpoint between the impaired and unimpaired watersheds’ 95 percent confidence interval for the median, were estimated to be 2.01 mg/L, 0.07 mg/L, and 197.27 mg/L for nitrogen, phosphorus, and sediment, respectively. Annual unit area load thresholds were estimated to be equal to 8.64 kg/ha, 0.30 kg/ha, and 785.29 kg/ha, respectively, for nitrogen, phosphorus, and sediment species.     

INFLUENCE OF DIFFERENT TEMPORAL SAMPLING STRATEGIES ON ESTIMATING TOTAL PHOSPHORUS AND SUSPENDED SEDIMENT CONCENTRATION AND TRANSPORT IN SMALL STREAMS1

ABSTRACT: Various temporal sampling strategies are used to monitor water quality in small streams. To determine how various strategies influence the estimated water quality, frequently collected water quality data from eight small streams (14 to 110 km²) in Wisconsin were systematically subsampled to simulate typically used strategies. These subsets of data were then used to estimate mean, median, and maximum concentrations, and with continuous daily flows used to estimate annual loads (using the regression method) and volumetrically weighted mean concentrations. For each strategy, accuracy and precision in each summary statistic were evaluated by comparison with concentrations and loads of total phosphorus and suspended sediment estimated from all available data. The most effective sampling strategy depends on the statistic of interest and study duration. For mean and median concentrations, the most frequent fixed period sampling economically feasible is best. For maximum concentrations, any strategy with samples at or prior to peak flow is best. The best sampling strategy to estimate loads depends on the study duration. For one‐year studies, fixed period monthly sampling supplemented with storm chasing was best, even though loads were overestimated by 25 to 50 percent. For two to three‐year load studies and estimating volumetrically weighted mean concentrations, fixed period semimonthly sampling was best.     

Comparison of Unsteady and Quasi‐Unsteady Flow Models in Simulating Sediment Transport in an Ephemeral Arizona Stream1

Hummel, Ryan, Jennifer G. Duan, and Shiyan Zhang, 2012. Comparison of Unsteady and Quasi‐Unsteady Flow Models in Simulating Sediment Transport in an Ephemeral Arizona Stream. Journal of the American Water Resources Association (JAWRA) 48(5): 987‐998. DOI: 10.1111/j.1752‐1688.2012.00663.x Abstract: Hydrodynamic and sediment transport models are useful engineering tools for predicting unsteady flood flow and sediment transport. Many models such as HEC‐RAS, HEC‐6, and IALLUVIAL apply quasi‐unsteady flow model, whereas others apply the unsteady flow model. It remains unknown if a quasi‐unsteady flow model is sufficiently accurate for simulating sediment transport in rapidly varied unsteady flood events, especially in ephemeral rivers in arid and semiarid regions. This study compared the quasi‐unsteady HEC‐RAS 4.1 model with one‐dimensional (1D) Finite Volume Method (FVM) based model in simulating flood flow and sediment transport in the Pantano Wash, a dryland river in the state of Arizona. The objective is to determine which sediment transport method is appropriate in predicting bed elevation changes in an ephemeral stream, Pantano Wash, and if an unsteady model is more accurate than a quasi‐unsteady flow model in predicting sediment transport. Results showed that the quasi‐unsteady HEC‐RAS model and the 1D FVM yielded similar results of bed degradation and aggradation for this dryland stream, although the FVM model predicted better flood hydrographs. Among the seven sediment transport formulas embedded in HEC‐RAS, Yang’s and Engelund‐Hansen’s equations gave the best matches with the field measurements for this particular case study.     

Evaluation of regression methodology with low-frequency water quality sampling to estimate constituent loads for ephemeral watersheds in Texas

Water quality regulation and litigation have elevated the awareness and need for quantifying water quality and source contributions in watersheds across the USA. In the present study, the regression method, which is typically applied to large (perennial) rivers, was evaluated in its ability to estimate constituent loads (NO(3)-N, total N, PO(4)-P, total P, sediment) on three small (ephemeral) watersheds with different land uses in Texas. Specifically, regression methodology was applied with daily flow data collected with bubbler stage recorders in hydraulic structures and with water quality data collected with four low-frequency sampling strategies: random, rise and fall, peak, and single stage. Estimated loads were compared with measured loads determined in 2001-2004 with an autosampler and high-frequency sampling strategies. Although annual rainfall and runoff volumes were relatively consistent within watersheds during the study period, measured annual nutrient and sediment concentrations and loads varied considerably for the cultivated and mixed watersheds but not for the pasture watershed. Likewise, estimated loads were much better for the pasture watershed than the cultivated and mixed landuse watersheds because of more consistent land management and vegetation type in the pasture watershed, which produced stronger correlations between constituent loads and mean daily flow rates. Load estimates for PO(4)-P were better than for other constituents possibly because PO(4)-P concentrations were less variable within storm events. Correlations between constituent concentrations and mean daily flow rate were poor and not significant for all watersheds, which is different than typically observed in large rivers. The regression method was quite variable in its ability to accurately estimate annual nutrient loads from the study watersheds; however, constituent load estimates were much more accurate for the combined 3-yr period. Thus, it is suggested that for small watersheds, regression-based annual load estimates should be used with caution, whereas long-term estimates can be much more accurate when multiple years of concentration data are available. The predictive ability of the regression method was similar for all of the low-frequency sampling strategies studied; therefore, single-stage or random strategies are recommended for low-frequency storm sampling on small watersheds because of their simplicity.     

Magnitude,Frequency, and Duration Relations for Suspended Sediment in Stable (“Reference”) Southeastern Streams1

Abstract: Sediment is listed as one of the leading causes of water‐quality impairments in surface waters of the United States (U.S.). A water body becomes listed by a State, Territory or Tribe if its designated use is not being attained (i.e., impaired). In many cases, the prescribed designated use is aquatic health or habitat, indicating that total maximum daily loads (TMDL) targets for sediment should be functionally related to this use. TMDL targets for sediment transport have been developed for many ecoregions over the past several years using suspended‐sediment yield as a metric. Target values were based on data from “reference” streams or reaches, defined as those exhibiting geomorphic characteristics of equilibrium. This approach has proved useful to some states developing TMDLs for suspended sediment, although one cannot conclude that if a stream exceeds the target range, the aquatic ecosystem will be adversely impacted. To address this problem, historical flow‐transport and sediment‐transport data from hundreds of sites in the Southeastern U.S. were re‐examined to develop parameters (metrics) such as frequency and duration of sediment concentrations. Sites determined as geomorphically stable from field evaluations and from analysis of gauging‐station records were sorted by ecoregion. Mean‐daily flow data obtained from the U.S. Geological Survey were applied to sediment‐transport rating relations to determine suspended‐sediment load for each day of record. The frequency and duration that a given concentration was equaled or exceeded were then calculated to produce a frequency distribution for each site. “Reference” distributions were created using the stable sites in each ecoregion by averaging all of the distributions at specified exceedance intervals. As with the “reference” suspended‐sediment yields, there is a broad range of frequency and duration distributions that reflects the hydrologic and sediment‐transport regimes of the ecoregions. Ecoregions such as the Mississippi Valley Loess Plains (#74) maintain high suspended sediment concentrations for extended periods, whereas coastal plain ecoregions (#63 and 75) show much lower concentrations.     

Estimation of Catchment Nutrient Loads in New Zealand Using Monthly Water Quality Monitoring Data

Causes of variation between loads estimated using alternative calculation methods and their repeatability were investigated using 20 years of daily flow and monthly concentration samples for 77 rivers in New Zealand. Loads of dissolved and total nitrogen and phosphorus were calculated using the Ratio, L5, and L7 methods. Estimates of loads and their precision associated with short‐term records of 5, 10, and 15 years were simulated by subsampling. The representativeness of the short‐term loads was quantified as the standard deviation of the 20 realizations. The L7 method generally produced more realistic loads with the highest precision and representativeness. Differences between load estimates were shown to be associated with poor agreement between the data and the underlying model. The best method was shown to depend on the match between the model and functional and distributional characteristics of the data, rather than on the contaminant. Short‐term load estimates poorly represented the long‐term load estimate, and deviations frequently exceeded estimated imprecision. The results highlight there is no single preferred load calculation method, the inadvisability of “unsupervised” load estimation and the importance of inspecting concentration‐flow, unit load‐flow plots and regression residuals. Regulatory authorities should be aware that the precision of loads estimated from monthly data are likely to be “optimistic” with respect to the actual repeatability of load estimates.     

Temporal and Spatial Trends in Nutrient and Sediment Loading to Lake Tahoe,California‐Nevada,USA

Since 1980, the Lake Tahoe Interagency Monitoring Program (LTIMP) has provided stream‐discharge and water quality data—nitrogen (N), phosphorus (P), and suspended sediment—at more than 20 stations in Lake Tahoe Basin streams. To characterize the temporal and spatial patterns in nutrient and sediment loading to the lake, and improve the usefulness of the program and the existing database, we have (1) identified and corrected for sources of bias in the water quality database; (2) generated synthetic datasets for sediments and nutrients, and resampled to compare the accuracy and precision of different load calculation models; (3) using the best models, recalculated total annual loads over the period of record; (4) regressed total loads against total annual and annual maximum daily discharge, and tested for time trends in the residuals; (5) compared loads for different forms of N and P; and (6) tested constituent loads against land use‐land cover (LULC) variables using multiple regression. The results show (1) N and P loads are dominated by organic N and particulate P; (2) there are significant long‐term downward trends in some constituent loads of some streams; and (3) anthropogenic impervious surface is the most important LULC variable influencing water quality in basin streams. Many of our recommendations for changes in water quality monitoring and load calculation methods have been adopted by the LTIMP.     

INCORPORATING NATURAL VARIABILITY,UNCERTAINTY, AND RISK INTO WATER QUALITY EVALUATIONS USING DURATION CURVES1

ABSTRACT: Quantifying natural variability, uncertainty, and risk with minimal data is one of the greatest challenges facing those engaged in water quality evaluations, such as development of total maximum daily loads (TMDL), because of regulatory, natural, and analytical constraints. Quantification of uncertainty and variability in natural systems is illustrated using duration curves (DCs), plots that illustrate the percent of time that a particular flow rate (FDC), concentration (CDC), or load rate (LDC; “TMDL”) is exceeded, and are constructed using simple derived distributions. Duration curves require different construction methods and interpretations, depending on whether there is a statistically significant correlation between concentration (C) and flow (Q), and on the sign of the C‐Q regression slope (positive or negative). Flow DCs computed from annual runoff data vary compared with an FDC developed using all data. Percent exceedance for DCs can correspond to risk; however, DCs are not composed of independent quantities. Confidence intervals of data about a regression line can be used to develop confidence limits for the CDC and LDC. An alternate expression to a fixed TMDL is suggested as the risk of a load rate being exceeded and lying between confidence limits. Averages over partial ranges of DCs are also suggested as an alternative expression of TMDLs. DCs can be used to quantify watershed response in terms of changes in exceedances, concentrations, and load rates after implementation of best management practices.     

Enhancing Hyrdological Simulation Program – FORTRAN Model Channel Hydraulic Representation1

Abstract: The hydrological simulation program – FORTRAN (HSPF) is a comprehensive watershed model that employs depth‐area‐volume‐flow relationships known as the hydraulic function table (FTABLE) to represent the hydraulic characteristics of stream channel cross‐sections and reservoirs. An accurate FTABLE determination for a stream cross‐section site requires an accurate determination of mean flow depth, mean flow width, roughness coefficient, longitudinal bed slope, and length of stream reach. A method that uses regional regression equations to estimate mean flow depth, mean flow width, and roughness coefficient is presented herein. FTABLES generated by the proposed method (Alternative Method) and FTABLES generated by Better Assessment Science Integrating Point and Nonpoint Sources (BASINS) were compared. As a result, the Alternative Method was judged to be an enhancement over the BASINS method. First, the Alternative Method employs a spatially variable roughness coefficient, whereas BASINS employs an arbitrarily selected spatially uniform roughness coefficient. Second, the Alternative Method uses mean flow width and mean flow depth estimated from regional regression equations whereas BASINS uses mean flow width and depth extracted from the National Hydrography Dataset (NHD). Third, the Alternative Method offers an option to use separate roughness coefficients for the in‐channel and floodplain sections of compound channels. Fourth, the Alternative Method has higher resolution in the sense that area, volume, and flow data are calculated at smaller depth intervals than the BASINS method. To test whether the Alternative Method enhances channel hydraulic representation over the BASINS method, comparisons of observed and simulated streamflow, flow velocity, and suspended sediment were made for four test watersheds. These comparisons revealed that the method used to estimate the FTABLE has little influence on hydrologic calibration, but greatly influences hydraulic and suspended sediment calibration. The hydrologic calibration results showed that observed versus simulated daily streamflow comparisons had Nash‐Sutcliffe efficiencies ranging from 0.50 to 0.61 and monthly comparisons had efficiencies ranging from 0.61 to 0.84. Comparisons of observed and simulated suspended sediments concentrations had model efficiencies ranging from 0.48 to 0.56 for the daily, and 0.28 to 0.70 for the monthly comparisons. The overall results of the hydrological, hydraulic, and suspended sediment concentration comparisons show that the Alternative Method yielded a relatively more accurate FTABLE than the BASINS method. This study concludes that hydraulic calibration enhances suspended sediment simulation performance, but even greater improvement in suspended sediment calibration can be achieved when hydrological simulation performance is improved. Any improvements in hydrological simulation performance are subject to improvements in the temporal and spatial representation of the precipitation data.     

From agricultural intensification to conservation: sediment transport in the Raccoon River, Iowa, 1916-2009

Fluvial sediment is a ubiquitous pollutant that negatively affects surface water quality and municipal water supply treatment. As part of its routine water supply monitoring, the Des Moines Water Works (DMWW) has been measuring turbidity daily in the Raccoon River since 1916. For this study, we calibrated daily turbidity readings to modern total suspended solid (TSS) concentrations to develop an estimation of daily sediment concentrations in the river from 1916 to 2009. Our objectives were to evaluate long-term TSS patterns and trends, and relate these to changes in climate, land use, and agricultural practices that occurred during the 93-yr monitoring period. Results showed that while TSS concentrations and estimated sediment loads varied greatly from year to year, TSS concentrations were much greater in the early 20th century despite drier conditions and less discharge, and declined throughout the century. Against a backdrop of increasing discharge in the Raccoon River and widespread agricultural adaptations by farmers, sediment loads increased and peaked in the early 1970s, and then have slowly declined or remained steady throughout the 1980s to present. With annual sediment load concentrated during extreme events in the spring and early summer, continued sediment reductions in the Raccoon River watershed should be focused on conservation practices to reduce rainfall impacts and sediment mobilization. Overall, results from this study suggest that efforts to reduce sediment load from the watershed appear to be working.     

DRY AND WET WEATHER FLOW NUTRIENT LOADS FROM A LOS ANGELES WATERSHED1

Effective watershed management requires an accurate assessment of the pollutant loads from the associated point and nonpoint sources. The importance of wet weather flow (WWF) pollutant loads is well known, but in semi‐arid regions where urbanization is significant the pollutant load in dry weather flow (DWF) may also be important. This research compares the relative contributions of potential contaminants discharged in DWF and WWF from the Ballona Creek Watershed in Los Angeles, California. Models to predict DWF and WWF loads of total suspended solids, biochemical oxygen demand, nitrate‐nitrogen, nitrite‐nitrogen, ammonia‐nitrogen, total Kjeldahl nitrogen, and total phosphorus from the Ballona Creek Watershed for six water years dating from 1991 to 1996 were developed. The contaminants studied were selected based on data availability and their potential importance in the degradation of Ballona Creek and Santa Monica Bay beneficial uses. Wet weather flow was found to contribute approximately 75 percent to 90 percent of the total annual flow volume discharged by the Ballona Creek Watershed. Pollutant loads are also predominantly due to WWF, but during the dry season, DWF is a more significant contributor. Wet weather flow accounts for 67 to 98 percent of the annual load of the constituents studied. During the dry season, however, the portion attributable to DWF increases to greater than 40 percent for all constituents except biochemical oxygen demand and total suspended solids. When individual catchments within the watershed are considered, the DWF pollutant load from the largest catchment is similar to the WWF pollutant load in two other major catchments. This research indicates WWF is the most significant source of nonpoint source pollution load on an annual basis, but management of the effects of the nonpoint source pollutant load should consider the seasonal importance of DWF.     

ANALYSIS OF LAKE-BOTTOM SEDIMENT TO ESTIMATE HISTORICAL NONPOINT-SOURCE PHOSPHORUS LOADS1

ABSTRACT Bottom sediment in Hillsdale Lake, Kansas, was analyzed to estimate the annual load of total phosphorus deposited in the lake from nonpoint sources. Topographic, bathymetric, and sediment-core data were used to estimate the total mass of phosphorus in the lake-bottom sediment. Available streamflow and water-quality data were used to compute the mean annual mass of phosphorus (dissolved plus suspended) exiting the lake. The mean annual load of phosphorus added to the lake from point sources was estimated from previous studies. A simple mass balance then was used to compute the mean annual load of phosphorus from non-point sources. The total mass of phosphorus in the lake-bottom sediment was estimated to be 924,000 kg, with a mean annual load of 62,000 kg. The mean annual mass of phosphorus exiting in the lake outflow was estimated to be about 8,000 kg. The mean annual loads of phosphorus added to the lake from point and nonpoint sources were estimated to be 5,000 and 65,000 kg, respectively. Thus, the contribution to the total mean annual phosphorus load in Hillsdale Lake is about 7 percent from point sources and about 93 percent from nonpoint sources.     

Concentration‐Duration‐Frequency Curves for Stream Turbidity: Possibilities for Assessing Biological Impairment1

Abstract: Siltation and subsequent biological impairment is a national problem prompting state regulatory agencies to develop sediment total maximum daily loads (TMDL) for many streams. To support TMDL targets for reduced sediment yield in disturbed watersheds, a critical need exists for stream assessments to identify threshold concentrations of suspended sediment that impact aquatic biota. Because of the episodic nature of stream sediment transport, thresholds should not only be a function of sediment concentration, but also of duration and dose frequency. Water quality sondes can collect voluminous amounts of turbidity data, a surrogate for suspended sediment, at intervals that can be used to characterize concentration, duration, and frequency of elevated turbidity events. To characterize turbidity sonde data in an ecologically relevant manner, a methodology for concentration‐duration‐frequency (CDF) curves was developed using turbidity doses that relate to different levels of biological impairment. To illustrate this methodology, turbidity CDF curves were generated for two sites on Little Pigeon River in the Great Smoky Mountains National Park, Tennessee, using over 30,000 sonde data measurements per site for a one‐year period. Utilizing a Poisson arrival approach, turbidity spikes were analyzed stochastically by observing the frequency and duration of recorded events over a turbidity level that relates to a biological dose response. An exponential equation was used to fit duration and frequency of a specified turbidity level to generate concentric‐shaped CDF curves, where at specific turbidities longer durations occurred less frequently and conversely shorter durations occurred more frequently. The significance of the equation fit to the data was accomplished with a Kolmogorov‐Smirnov goodness‐of‐fit test. Our findings showed that the CDF curves derived by an exponential function performed reasonable well, with most curves significant at a 95% confidence level. These CDF curves were then used to demonstrate how they could be used to assess biological impairment, and identify future research needs for improved development of sediment TMDLs.     

Influence of Sampling Frequency on Estimation of Annual Total Phosphorus and Total Suspended Solids Loads1

Abstract: The determination of sediment and nutrient loads is typically based on the collection and analysis of grab samples. The frequency and regularity of traditional sampling may not provide representation of constituent loading, particularly in systems with flashy hydrology. At two sites in the Little Bear River, Utah, continuous, high‐frequency turbidity was used with surrogate relationships to generate estimates of total phosphorus and total suspended solids concentrations, which were paired with discharge to estimate annual loads. The high frequency records were randomly subsampled to represent hourly, daily, weekly, and monthly sampling frequencies and to examine the effects of timing, and resulting annual load estimates were compared to the reference loads. Higher frequency sampling resulted in load estimates that better approximated the reference loads. The degree of bias was greater at the more hydrologically responsive site in the upper watershed, which required a higher sampling frequency than the lower watershed site to achieve the same level of accuracy in estimating the reference load. The hour of day and day of week of sampling impacted load estimation, depending on site and hydrologic conditions. The effects of sampling frequency on the determination of compliance with a water quality criterion were also examined. These techniques can be helpful in determining necessary sampling frequency to meet the objectives of a water quality monitoring program.     

NUTRIENT CONTRIBUTION OF NONPOINT SOURCE RUNOFF IN THE LAS VEGAS VALLEY1

ABSTRACT: A Geographic Information System (GIS) based non‐point source runoff model is developed for the Las Vegas Valley, Nevada, to estimate the nutrient loads during the years 2000 and 2001. The estimated nonpoint source loads are compared with current wastewater treatment facilities loads to determine the non‐point source contribution of total phosphorus (TP), total nitrogen (TN), and total suspended solids (TSS) on a monthly and annual time scale. An innovative calibration procedure is used to estimate the pollutant concentrations for different land uses based on available water quality data at the outlet. Results indicate that the pollutant concentrations are higher for the Las Vegas Valley than previous published values for semi‐arid and arid regions. The total TP and TN loads from nonpoint sources are approximately 15 percent and 4 percent, respectively, of the total load to the receiving water body, Lake Mead. The TP loads during wet periods approach the permitted loads from the wastewater treatment plants that discharge into Las Vegas Wash. In addition, the GIS model is used to track pollutant loads in the stream channels for one of the subwatersheds. This is useful for planning the location of Best Management Practices to control nonpoint pollutant loads.     

WATERSHED OPTIMIZATION OF AGRICULTURAL BEST MANAGEMENT PRACTICES: CONTINUOUS SIMULATION VERSUS DESIGN STORMS1

ABSTRACT: Nonpoint source (NPS) models and expert opinions are often used to prescribe best management practices (BMPs) for controlling NPS pollution. An optimization algorithm (e.g., a genetic algorithm, or GA) linked with a NPS model (e.g., Annualized AGricultural Nonpoint Source pollution model, or AnnAGNPS), can be used to more objectively prescribe BMPs and to optimize NPS pollution control measures by maximizing pollutant reduction and net monetary return from a watershed. Pollutant loads from design storms and annual loads from a continuous simulation can both be used for optimizing BMP schemes. However, which strategy results in a better solution (in terms of providing water quality protection) for a watershed is not clear. The specific objective of the study was to determine the differences in watershed pollutant loads, in an experimental watershed in Pennsylvania, resulting from optimization analyses performed using pollutant loads from a series of five 2‐yr 24‐hr storm events, a series of five 5‐yr 24‐hr storm events, and cumulative pollutant loads from a continuous simulation of five years of weather data. For each of these three different event alternatives, 100 near optimal solutions (BMP schemes) were generated. Sediment (Sed), sediment nitrogen (SedN), dissolved N (SolN), sediment organic carbon (SedOC), and sediment phosphorus (SedP) loads from a different five‐year period (an evaluation period) suggest that the optimal BMP schemes resulting from the use of annual cumulative pollutant loads from a continuous simulation of five years of weather data provide smaller cumulative NPS pollutant loads at the watershed outlet.     

Integrating Temporal Inequality into Conservation Planning to Improve Practice Design and Efficacy

In contrast to spatial inequality, there are currently no methods for leveraging information on temporal inequality to improve conservation efficacy. The objective of this study was to use Lorenz curves to quantify temporal inequality in surface runoff and tile drainage, identify controls on nutrient loading in these flowpaths, and develop design flows for structural conservation practices. Surface runoff (n = 94 site‐years) and tile drainage (n = 90 site‐years) were monitored on 40 fields in Ohio. Results showed, on average, 80% of nitrate‐nitrogen, soluble reactive phosphorus (P), and total P loads occurred between 7 and 12 days per year in surface runoff and between 32 and 58 days per year in tile drainage. Similar temporal inequality between discharge and load provided evidence that loading was transport‐limited and highlighted the critical role hydrologic connectivity plays in nutrient delivery from tile‐drained fields. Design flow criterion for sizing structural practices based on load reduction goals was developed by combining Lorenz curves and flow duration curves. Comparing temporal inequality between fields and the Maumee River, the largest tributary to the western Lake Erie Basin, revealed challenges associated with achieving watershed load reduction goals with field‐scale conservation. In‐field (i.e., improved nutrient and water management), edge‐of‐field (i.e., structural practices), and instream practices will all be required to meet nutrient reduction goals from tile‐drained watersheds.     

Comparative study of transport processes of nitrogen, phosphorus, and herbicides to streams in five agricultural basins, USA

Agricultural chemical transport to surface water and the linkage to other hydrological compartments, principally ground water, was investigated at five watersheds in semiarid to humid climatic settings. Chemical transport was affected by storm water runoff, soil drainage, irrigation, and how streams were linked to shallow ground water systems. Irrigation practices and timing of chemical use greatly affected nutrient and pesticide transport in the semiarid basins. Irrigation with imported water tended to increase ground water and chemical transport, whereas the use of locally pumped irrigation water may eliminate connections between streams and ground water, resulting in lower annual loads. Drainage pathways in humid environments are important because the loads may be transported in tile drains, or through varying combinations of ground water discharge, and overland flow. In most cases, overland flow contributed the greatest loads, but a significant portion of the annual load of nitrate and some pesticide degradates can be transported under base-flow conditions. The highest basin yields for nitrate were measured in a semiarid irrigated system that used imported water and in a stream dominated by tile drainage in a humid environment. Pesticide loads, as a percent of actual use (LAPU), showed the effects of climate and geohydrologic conditions. The LAPU values in the semiarid study basin in Washington were generally low because most of the load was transported in ground water discharge to the stream. When herbicides are applied during the rainy season in a semiarid setting, such as simazine in the California basin, LAPU values are similar to those in the Midwest basins.     

Thirty-year trends in suspended sediment in seven Lake Erie tributaries

Sediment is an important pollutant for Lake Erie and its tributaries as a carrier of other substances and as a pollutant in its own right. Environmental managers have called for major reductions in sediment loadings in Lake Erie tributaries. In this study, 30-yr (1975-2005) datasets with daily resolution are analyzed to identify and interpret trends in sediment concentrations and loads in major US tributaries to Lake Erie. The Maumee and Sandusky Rivers in agricultural northwest Ohio show continual decreases throughout this period, but the River Raisin shows increases, especially in the last decade. The urban and forested Cuyahoga River shows little trend before 2000 but shows increases since then. The mostly forested Grand River shows strong decreases before 1995, little change thereafter until the early 2000s, and then increases. In most cases, the greatest decreases or smallest increases, depending on the river, are associated with summer and fall and with low flow conditions, whereas the smallest decreases or greatest increases are associated with the spring and with high flow conditions. Analysis of concentration-flow relationships indicates that these changes are not due to weather but reflect positive and negative anthropogenic influences. Sediment decreases in the northwestern Ohio tributaries seem to reflect the successful use of agricultural practices to reduce erosion and prevent sediment loss. Opportunities for further reductions in sediment loads and concentrations lie in better management of sediment losses during winter and spring.