Dissolved organic matter effects on the performance of a barrier to polycyclic aromatic hydrocarbon transport by groundwater

In order to contain the movement of organic contaminants in groundwater, a subsurface sorption barrier consisting of sand or clay minerals coated with a cationic surfactant has been proposed. The effectiveness of such a sorption barrier might be affected by the presence of dissolved organic matter (DOM) in the groundwater. To study the impact of DOM on barrier performance, a series of batch experiments were performed by measuring naphthalene and phenanthrene sorption onto sand coated with cetylpyridinium chloride (CPC) and bentonite coated with hexadecyltrimethylammonium bromide (HDTMA) in the presence of various concentrations of DOM. The overall soil-water distribution coefficient (K*) of naphthalene and phenanthrene onto CPC-coated sand decreased with increasing DOM concentration, whereas the K* of the compounds onto HDTMA-coated bentonite slightly increased with increasing DOM concentration. To describe the overall distribution of polycyclic aromatic hydrocarbons (PAHs) in the systems, a competitive multiphase sorption (CMS) model was developed and compared with an overall mechanistic sorption (OMS) model. The modeling studies showed that while the OMS model did not explain the CPC-coated sand experimental results, a model that included competitive sorption between DOM and PAH did. The experimental results and the modeling study indicated that there was no apparent competition between DOM and PAH in the HDTMA-coated bentonite system, and indicated that in groundwater systems with high DOM, a barrier using HDTMA-coated bentonite might be more effective.     

The fate of the aqueous phase polycyclic aromatic hydrocarbon fraction in a detention pond system

The concentration of dissolved polycyclic aromatic hydrocarbons (PAH) in influent, effluent, and within a detention pond system was measured. The "soluble fraction" was operationally defined as the PAHs in solution that passed through a 1.2 μm filter. The results show that influent and effluent PAH concentrations were similar, indicating that dissolved PAH moved essentially unhindered through the detention pond system. In general, low molecular weight PAH were present at the highest concentrations and the highest PAH concentrations were measured in Summer. Also, year-to-year variations in PAH concentration were observed. At the end of sufficiently large storms, the pond was comparably unpolluted. During dry periods, the dissolved PAH concentration rose, possibly due to evapoconcentration and by partitioning of PAH from trapped contaminated sediment in the detention pond system. This study provides evidence that aqueous-phase PAH concentrations in runoff water were relatively unaffected by the passage through a conventional detention pond system.     

Photoirradiation of polycyclic aromatic hydrocarbon diones by UVA light leading to lipid peroxidation

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous genotoxic environmental pollutants and potentially pose a health risk to humans. In most if not all cases, PAHs in the environment can be oxidized into their corresponding PAH-diones. This process is considered a detoxification pathway with regard to tumorigenicity. Nevertheless, photo-induced toxicological activity of PAH-diones has not been systematically investigated. In this study, we show that 27 potential environmental PAH-diones induced lipid peroxidation, in a dose (light) response manner, when irradiated with UVA at 7 and 21 J cm⁻². Photoirradiation in the presence of sodium azide, deuterated methanol, or superoxide dismutase revealed that lipid peroxidation is mediated by reactive oxygen species. Electron spin resonance (ESR) spin trapping studies supported this observation. These results suggest that UVA photoirradiation of PAH-diones generates reactive oxygen species and induces lipid peroxidation.     

The lack of microbial degradation of polycyclic aromatic hydrocarbons from coal-rich soils

Analytical techniques used to assess the environmental risk of contamination from polycyclic aromatic hydrocarbons (PAHs) typically consider only abiotic sample parameters. Supercritical fluid extraction and sorption enthalpy experiments previously suggested slow desorption rates for PAH compounds in two coal-contaminated floodplain soils. In this study, the actual PAH availability for aerobic soil microorganisms was tested in two series of soil-slurry experiments. The experimental conditions supported microbial degradation of phenanthrene if it was weakly sorbed onto silica gel. Native coals and coal-derived particles in two soils effectively acted as very strong sorbents and prevented microbial PAH degradation. The long history of PAH exposure and degree of coal contamination apparently had no influence on the capability of the microbial soil community to overcome constraints of PAH availability. Within the context of the experimental conditions and the compounds chosen, our results confirm that coal-bound PAHs are not bioavailable and hence of low environmental concern.     

Effect of fuel composition and engine operating conditions on polycyclic aromatic hydrocarbon emissions from a fleet of heavy-duty diesel buses

Emissions from 12 in-service heavy-duty buses powered by low- (LSD) and ultra low-sulfur (ULSD) diesel fuels were measured with the aim to characterize the profile of polycyclic aromatic hydrocarbons (PAHs) in the exhaust and to identify the effect of different types of fuels on the emissions. To mimic on-road conditions as much as possible, sampling was conducted on a chassis dynamometer at four driving modes, namely: mode 7 or idle (0% power), mode 11 (25% power), mode 10 (50% power) and mode 8 (100% power). Irrespective of the type of fuel used, naphthalene, acenaphthene, acenaphthylene, anthracene, phenanthrene, fluorene, fluoranthene and pyrene were found to be the dominant PAHs in the exhaust emissions of the buses. However, the PAH composition in the exhausts of ULSD buses were up to 91±6% less than those in the LSD buses. In particular, three- and four-ringed PAHs were more abundant in the later than in the former. Lowering of fuel sulfur content not only reduced PAH emission, but also decreased the benzo(a)pyrene equivalent (BAP_eq) and hence the toxicity of the exhaust. Result from multicriteria decision-making and multivariate data analysis techniques showed that the use of ULSD afforded cleaner exhaust compositions and emissions with characteristics that are distinct from those obtained by the use of LSD.     

The monitoring of biofilm formation in a mulch biowall barrier and its effect on performance

Lab scale mulch biofilm biowall barriers were constructed and tested to monitor the effect of biofilm formation on the performance of the biobarrier. Naphthalene, a two-ring polycyclic aromatic hydrocarbon (PAH), was used as the model compound. With column reactors, the amounts of viable naphthalene degraders and biofilm formation were monitored, as was the performance of the biobarrier. The sorption capacity of the mulch, the increase in biomass and the extracellular polymeric substance (EPS) content of the biofilm created a strong affinity for naphthalene and induced an increase in the number of slowly growing hydrocarbon degraders, resulting in a higher degradation rate and more stable PAH removal. Concentration profiles of pore water naphthalene and electron acceptors indicated that dissolved oxygen (DO) was preferentially used as the electron acceptor, and the greatest removal occurred at the inlet to the column reactor where DO was highest. However, when using nitrate as an alternative electron acceptor, both biofilm formation and continual degradation of naphthalene also occurred. Microprofiles of DO in the biofilm revealed that oxygen transport in the biofilm was limited, and there might be sequential utilization of nitrate for naphthalene removal in the anoxic zones of the biofilm. These results provide insight into the distribution of viable biomass and biofilm EPS production in engineered permeable reactive mulch biobarriers.     

Oxidant denuder sampling for analysis of polycyclic aromatic hydrocarbons and their oxygenated derivates in ambient aerosol: evaluation of sampling artefact

The concentrations of some polycyclic aromatic hydrocarbons (PAH) and oxygenated PAH (O-PAH) can be changed by oxidation reactions during sampling. This can lead to an over- or underestimation of the corresponding adverse health effects. The aim of this study was the evaluation of these sampling artefacts. The potential of using an oxidant denuder was shown by parallel low-volume sampling with and without MnO₂ ozone denuder. Twenty-three PAH and 11 O-PAH in ambient air were analysed, both in the vapour and particulate phase. The denuder was proven to be highly efficient for stripping ozone from air while causing no significant particle losses. In general, the concentrations of 5- to 7-ring PAH, which are predominantly associated with particles, were underestimated in non-denuded samples. The highest losses due to reaction with ozone and other atmospheric oxidants were observed for benzo[a]pyrene and perylene. Concurrently, the concentrations of most of the mainly particle-associated 4- to 5-ring O-PAH were higher in the non-denuded samples. The denuder did not only remove ozone, moreover other gaseous species such as more volatile PAH and O-PAH were partially oxidized on the catalytic surface, too. Degradation of PAH and concurrent degradation/formation reactions of O-PAH occurred. The corresponding reactivities of selected PAH and O-PAH are discussed.     

A strategy for aromatic hydrocarbon bioremediation under anaerobic conditions and the impacts of ethanol: a microcosm study

Increased use of ethanol-blended gasoline (gasohol) and its potential release into the subsurface have spurred interest in studying the biodegradation of and interactions between ethanol and gasoline components such as benzene, toluene, ethylbenzene and xylene isomers (BTEX) in groundwater plumes. The preferred substrate status and the high biological oxygen demand (BOD) posed by ethanol and its biodegradation products suggests that anaerobic electron acceptors (EAs) will be required to support in situ bioremediation of BTEX. To develop a strategy for aromatic hydrocarbon bioremediation and to understand the impacts of ethanol on BTEX biodegradation under strictly anaerobic conditions, a microcosm experiment was conducted using pristine aquifer sand and groundwater obtained from Canadian Forces Base Borden, Canada. The initial electron accepter pool included nitrate, sulfate and/or ferric iron. The microcosms typically contained 400 g of sediment, 600 approximately 800 ml of groundwater, and with differing EAs added, and were run under anaerobic conditions. Ethanol was added to some at concentrations of 500 and 5000 mg/L. Trends for biodegradation of aromatic hydrocarbons for the Borden aquifer material were first developed in the absence of ethanol, The results showed that indigenous microorganisms could degrade all aromatic hydrocarbons (BTEX and trimethylbenzene isomers-TMB) under nitrate- and ferric iron-combined conditions, but not under sulfate-reducing conditions. Toluene, ethylbenzene and m/p-xylene were biodegraded under denitrifying conditions. However, the persistence of benzene indicated that enhancing denitrification alone was insufficient. Both benzene and o-xylene biodegraded significantly under iron-reducing conditions, but only after denitrification had removed other aromatics. For the trimethylbenzene isomers, 1,3,5-TMB biodegradation was found under denitrifying and then iron-reducing conditions. Biodegradation of 1,2,3-TMB or 1,2,4-TMB was slower under iron-reducing conditions. This study suggests that addition of excess ferric iron combined with limited nitrate has promise for in situ bioremediation of BTEX and TMB in the Borden aquifer and possibly for other sites contaminated by hydrocarbons. This study is the first to report 1,2,3-TMB biodegradation under strictly anaerobic condition. With the addition of 500 mg/L ethanol but without EA addition, ethanol and its main intermediate, acetate, were quickly biodegraded within 41 d with methane as a major product. Ethanol initially present at 5000 mg/L without EA addition declined slowly with the persistence of unidentified volatile fatty acids, likely propionate and butyrate, but less methane. In contrast, all ethanol disappeared with repeated additions of either nitrate or ferric iron, but acetate and unidentified intermediates persisted under iron-enhanced conditions. With the addition of 500 mg/L ethanol and nitrate, only minor toluene biodegradation was observed under denitrifying conditions and only after ethanol and acetate were utilized. The higher ethanol concentration (5000 mg/L) essentially shut down BTEX biodegradation likely due to high EA demand provided by ethanol and its intermediates. The negative findings for anaerobic BTEX biodegradation in the presence of ethanol and/or its biodegradation products are in contrast to recent research reported by Da Silva et al. [Da Silva, M.L.B., Ruiz-Aguilar, G.M.L., Alvarez, P.J.J., 2005. Enhanced anaerobic biodegradation of BTEX-ethanol mixtures in aquifer columns amended with sulfate, chelated ferric iron or nitrate. Biodegradation. 16, 105-114]. Our results suggest that the apparent conservation of high residual labile carbon as biodegradation products such as acetate makes natural attenuation of aromatics less effective, and makes subsequent addition of EAs to promote in situ BTEX biodegradation problematic.     

A calcite permeable reactive barrier for the remediation of Fluoride from spent potliner (SPL) contaminated groundwater

The use of calcite (CaCO3) as a substrate for a permeable reactive barrier (PRB) for removing fluoride from contaminated groundwater is proposed and is illustrated by application to groundwater contaminated by spent potliner leachate (SPL), a waste derived from the aluminium smelting process. The paper focuses on two issues in the implementation of calcite permeable reactive barriers for remediating fluoride contaminated water: the impact of the groundwater chemical matrix and CO2 addition on fluoride removal. Column tests comparing pure NaF solutions, synthetic SPL solutions, and actual SPL leachate indicate that the complex chemical matrix of the SPL leachate can impact fluoride removal significantly. For SPL contaminant mixtures, fluoride removal is initially less than expected from idealized, pure, solutions. However, with time, the effect of other contaminants on fluoride removal diminishes. Column tests also show that pH control is important for optimizing fluoride removal with the mass removed increasing with decreasing pH. Barrier pH can be regulated by CO2 addition with the point of injection being critical for optimising the remediation performance. Experimental and model results show that approximately 99% of 2300 mg/L fluoride can be removed when CO2 is injected directly into the barrier. This can be compared to approximately 30-50% removal when the influent solution is equilibrated with atmospheric CO2 before contact with calcite.     

Influence of hydrogeochemical processes on zero-valent iron reactive barrier performance: a field investigation

Geochemical and mineralogical changes were evaluated at a field Fe0-PRB at the Oak Ridge Y-12 site concerning operation performance during the treatment of U in high NO3- groundwater. In the 5-year study period, the Fe0 remained reactive as shown in pore-water monitoring data, where increases in pH and the removal of certain ionic species persisted. However, coring revealed varying degrees of cementation. After 3.8-year treatment, porosity reduction of up to 41.7% was obtained from mineralogical analysis on core samples collected at the upgradient gravel-Fe0 interface. Elsewhere, Fe0 filings were loose with some cementation. Fe0 corrosion and pore volume reduction at this site are more severe due to the presence of NO3- at a high level. Tracer tests indicate that hydraulic performance deteriorated: the flow distribution was heterogeneous and under the influence of interfacial cementation a large portion of water was diverted around the Fe0 and transported outside the PRB. Based on the equilibrium reductions of NO3- and SO4(2-) by Fe0 and mineral precipitation, geochemical modeling predicted a maximum of 49% porosity loss for 5 years of operation. Additionally, modeling showed a spatial distribution of mineral precipitate volumes, with the maximum advancing from the interface toward downgradient with time. This study suggests that water quality monitoring, coupled with hydraulic monitoring and geochemical modeling, can provide a low-cost method for assessing PRB performance.     

Occurrence of coal and coal-derived particle-bound polycyclic aromatic hydrocarbons (PAHs) in a river floodplain soil

A PAH contaminated river floodplain soil was separated according to grain size and density. Coal and coal-derived particles from coal mining, coal industry and coal transportation activities were identified by organic petrographic analysis in our samples. Distinct concentrations of PAHs were found in different grain size and density fractions, however, similar distribution patterns of PAHs indicated similar sources. In addition, although light fractions had the mass fraction by weight of less than 5%, they contributed almost 75% of the total PAHs in the soil. PAH concentrations of all sub fractions showed positive correlation with their TOC contents. Altogether, coal and coal-derived particles that were abundant in light fractions could be the dominant geosorbents for PAHs in our samples.     

Desorption of polycyclic aromatic hydrocarbons from field-contaminated soil to a two-dimensional hydrophobic surface before and after bioremediation

This study investigated environmental distributions and production mechanisms of chlorinated polycyclic aromatic hydrocarbons (Cl-PAHs) in the sediments from some tidal flats located in Asia. Cl-PAHs were found in sediments taken from Arao tidal flat, Kikuchigawa River and Shirakawa River. The range of ∑Cl-PAHs was from 25.5 to 483 pg g⁻¹ for Kikuchigawa River and Arao tidal flat, respectively.Concentrations of PAHs and Cl-PAHs showed no significant correlations (r = 0.134). This result suggests that the origins of these compounds differ. In the identified Cl-PAH isomers, the most abundant Cl-PAH isomer was 9,10-dichloroanthracene (9,10-di-Cl-ANT) in the three sites. In general, concentrations of Cl-ANTs in the coastal environment are about 3-5 orders of magnitude lower than those of anthracene (ANT). However, concentration ratios between Cl-ANTs and ANT (Cl-ANTs/ANT) in the sediments ranged from 4.1% to 24.6%. This result indicated that Cl-PAHs were not generated under industrial processes but the high concentration ratios have resulted from the contribution of photochemical production of Cl-ANTs in the sediments because ANT is known to have high photochemical reactivity.For examining this phenomenon, ANT adsorbed onto glass beads was irradiated with UV under the mimicked field conditions of tidal flats. As a result, it was noticed that, while chlorinated derivatives were negligible in a light-controlled group, production of 2-Cl-ANT, 9-Cl-ANT and 9,10-diCl-ANT on the irradiated surface were found in this study. These results suggest that photochemical reaction of PAHs can be a potential source of the occurrence of Cl-PAHs in the coastal environment.     

Toxicological and biochemical responses of the earthworm Lumbricus rubellus to pyrene, a non-carcinogenic polycyclic aromatic hydrocarbon

The effects of the polycyclic aromatic hydrocarbon (PAH) pyrene on earthworms were investigated in contact and soil tests. In addition to measuring toxic effects on survival and reproduction, Ethoxyresorufin-o-deethylase (EROD) activity and catalase activity were also studied as possible biomarkers of toxic stress. The survival data indicated that LC₅₀ values were 0.0068 mg/ml for the contact test, and 283 mg/kg in the soil test. Cocoon production rate was significantly reduced compared to controls at 160, 640 and 2560 mg/kg in the soil test. No EROD activity could be detected in preliminary studies using control and exposed animals from the contact test, so this assay was not used to the soil test. Catalase activity was shown to be significantly lower at 640 mg/kg in the soil test compared to all other treatments and the control. When compared to toxicological data for other soil invertebrates, Lumbricus rubellus has an intermediate sensitivity in respects of survival and a lower sensitivity for reproductive effects, although the soil used in this study had a higher organic content than previous studies, meaning that the sensitivity of this species may be underestimated in comparison to previous published data for other soil invertebrates.     

Dietary risk evaluation for 28 polycyclic aromatic hydrocarbons (PAHs) in tea preparations made of teas available on the Polish retail market

The aim of this work was to assess dietary risk resulting from consumption of polycyclic aromatic hydrocarbons (PAHs) with tea infusions. To this end, levels of 28 PAHs in black, green, red and white teas available on the Polish retail market have been assessed. Profiles and correlation between concentrations of individual PAHs have been identified. A model study on transfer of PAHs from tea leaves into tea preparations has been conducted. Relatively high concentrations of 28 evaluated PAHs have been found in 58 tested samples of black, green, red and white teas sampled on the Polish retail market. Total concentration ∑28PAH ranged from 57 to 696 µg kg^?1 with mean 258 µg kg^?1 (dry tea leaves). The most mature tea leaves fermented to a small degree contained relatively the highest PAH levels among all four tested tea types. Relatively low PAH transfer rates into tea infusions and limited volumes of the consumed tea keep the risks associated with PAH dietary intake at a safely low level.

The worst-case scenario dietary intake values were 7.62/0.82/0.097 ng kg^?1 b.w. day^?1 (estimated on the basis of the maximum found concentrations 696/113/23 µg kg^?1 and maximum observed transfer rates 24/16/9%) for ∑28PAH/∑PAH4/B[a]P, respectively. MOE values calculated using the above worst case estimates exceeded 700,000 and 400,000 (BMDL₁₀ 0.07 and 0.34 mg kg^?1 b.w. day^?1) for B[a]P and PAH4, respectively. Both B[a]P and PAH4 concentrations may be used as indicators of total PAH concentration in tea leaves; PAH4 slightly better fits low molecular weight PAHs. Several correlations between various PAHs/groups of PAHs have been identified, the strongest one (R² = 0.92) between PAH4 and EU PAH 15+1.     

Multi tracer test for the implementation of enhanced in-situ bioremediation at a BTEX-contaminated megasite

At the Centre for Environmental Research Leipzig-Halle (UFZ) research site in Zeitz, Germany, benzene contaminates the lower of two aquifers with concentrations of up to 20 mg/l. Since the benzene plume has a minimum length of approximately 1 km, enhanced natural attenuation measures are being considered as a remediation strategy. This study describes the performance and evaluation of a multi-species reactive tracer test using the tracers fluorescein and bromide as conservative tracers and toluene as reactive tracer. Sampling was performed over a period of six months using a detailed network of multilevel sampling wells. Toluene was only slightly retarded in comparison to bromide, whereas fluorescein was retarded considerably stronger. Therefore, it was not possible to use fluorescein as an in situ tracer for the determination of groundwater velocities. The ionic nature of fluorescein is assumed to be the major reason for its retardation. The results show that the infiltration conditions were suitable to produce a wide spreading of the tracer front along the full thickness of the aquifer. Thus, a large aquifer volume can be treated in future enhanced bioremediation measures. The total quantity of infiltrated toluene (24 l) was degraded under sulfate-reducing conditions over a flow path of 50 m. Benzylsuccinate was identified as a metabolite of toluene degradation under sulfate-reducing conditions at this site. The modelling results show that toluene degradation was described more accurately using Monod kinetics than first-order kinetics. Since toluene was only slightly retarded in comparison to bromide, sorption and desorption processes were considered to be negligible.     

A novel approach for characterization of polycyclic aromatic hydrocarbon (PAH) pollution patterns in sediments from Guanabara Bay, Rio de Janeiro, Brazil

A novel multivariate method based on principal component analysis of pre-processed sections of chromatograms is used to characterize the complex PAH pollution patterns in sediments from Guanabara Bay, Brazil. Five distinct sources of 3- to 6-ring PAHs could be revealed. The harbour is the most contaminated site in the bay, its plume stretches in a South West to North East direction and the chemical profile indicates mainly pyrogenic sources mixed with a fraction of high-molecular-weight petrogenic PAHs. Rio São João de Meriti is the second largest source of PAHs, and introduces mainly a fraction of low-molecular-weight petrogenic PAHs from the western region of Rio de Janeiro. The sites close to the ruptured pipeline at the Duque de Caxias Refinery show a distinctive pollution pattern indicating a heavy petroleum fraction. The method also led to the identification of new potential indicator ratios also involving coeluting peaks (e.g., triphenylene and chrysene).     

The behaviors and fate of polycyclic aromatic hydrocarbons (PAHs) in a coking wastewater treatment plant

The occurrence, behaviors and fate of 18 PAHs were investigated in a coking wastewater treatment plant in Songshan coking plant, located in Shaoguan, Guangdong Province of China. It was found that the target compounds occurred widely in raw coking wastewater, treated effluent, sludge and gas samples. In raw coking wastewater, high molecular weight (MW) PAHs were the dominant compounds, while 3-6 ring PAHs predominated in the final effluent. The dominant compounds in gas samples were phenathrene, fluoranthene and pyrene, while they were fluoranthene, pyrene, chrysene and benzo[k]fluoranthene for sludge. The process achieved over 97% removal for all the PAHs, 47-92% of eliminations of these target compounds in liquid phase were achieved in biological stage. Different behaviors of PAHs were observed in the primary tank, anaerobic tank, aerobic tank, hydrolytic tank and coagulation tank units, while heavier and lower ones were mainly removed in anaerobic tank and aerobic tanks, respectively. Regarding the fate of PAHs, calculated fractions of mass losses for low MW PAHs due to transformation and adsorption to sludge accounted for 15-50% and 24-49%, respectively, while the rest was less than 1%. For high MW PAHs, the mass losses were mainly due to adsorption to sludge and separation with tar (contributing 56-76% and 22-39%, respectively), and the removal through transformation was less.     

一株芴降解菌的分离鉴定及其对多环芳烃的降解广谱性研究

从某焦化厂活性污泥中筛选出一株芴的优势降解菌株W-1,经形态学观察、生理生化实验和16S rDNA基因序列分析,确定W-1为粪产碱杆菌.在接种量10%(V/V),初始芴浓度40 mg/L,pH 7.0,温度30℃的条件下,接种培养11 d后,菌株W-1对芴的降解效率达到87.8%.菌株W-1对多环芳烃的降解具有广谱性,...     

Using chemical models for evaluating the geochemical confinement capacity of a geological barrier application to the Centre de Stockage de l'Aube (France)

The feasibility of using a chemical reaction-based approach for evaluating and modelling the role of adsorption reactions in determining the geochernical confinement capacity of natural geological barriers is being studied as part of an on-going R & D programme. The confined superficial aquifer underlying the Centre de Stockage de l'Aube facility, a geological barrier for this site, has been used as a case study with the following aims. First, development of a site characterisation protocol and demonstration of its use to determine the principal geochemical characteristics of aquifer materials using batch experiments and to represent the information obtained in terms of a chemical model. The experimental results obtained for Ni²⁺ partitioning as a function of total Ni, pH, total Ca and total solid can be satisfactorily represented in terms of reactions with an ion exchange site and a single amphoteric surface hydroxyl site with ferrihydrite reaction constants. A second objective is the incorporation of the reactions in a coupled geochemistry/transport code, and to verify the applicability of the coupled code predictions for Ni²⁺ mass transfer by comparison with the results obtained during column tracer experiments. The breakthrough curve and equilibrium solid phase Ni loading, predicted by a one-dimensional coupled model for a column tracer experiment, agree closely with observed data.Additional studies are underway to reduce model conditionality, to extend the adsorption model to other analogue cations and anions, to incorporate the effect of natural organic matter and to take into consideration precipitation/dissolution of amorphous Fe surface phases.     

The application of HPLC ESI MS in the investigation of the flavonoids and flavonoid glycosides of a Caribbean Lamiaceae plant with potential for bioaccumulation

As part of an exchange technology program between the government of Barbados and Environment Canada, methanolic and aqueous extracts from the flavonoid-rich Lamiaceae family were characterized using negative-ion electrospray mass spectrometry. The species investigated is part of the Caribbean Pharmacopoeia, and is used for a variety of health issues, including colds, flu, diabetes, and hypertension. The extracts were investigated for structural elucidation of phenolics, identification of chemical taxonomic profile, and evidence of bio-accumulator potential. The methanolic and aqueous leaf extracts of Plectranthus amboinicus yielded rosmarinic acid, ladanein, cirsimaritin, and other methoxylated flavonoids. This genus also shows a tendency to form conjugates with monosaccharides, including glucose, galactose, and rhamnose. The aqueous extract yielded four isomeric rhamnosides. The formation of conjugates by Plectranthus amboinicus is thus evidence of high bioaccumulator significance.