Residual metal concentrations in soils and leaf accumulations in tobacco a decade following farmland application of municipal sludge

The objectives of this investigation were to examine the long-term residual effects of metal loading through sewage sludge applications on the total vs. diethylene triamine pentacetic acid (DTPA) extractable metal concentrations in soil and leaf accumulations in tobacco. Maryland tobacco (Nicotiana tabacum L.), cv. 'MD 609', was grown in 1983 and 1984 at two sites in Maryland that had been amended in 1972 with dewatered, digested sewage sludge from washington, DC, at rates equal to 0, 56, 112 and 224 mg ha(-1). The metal concentrations in the sludge, in mg kg(-1) dry weight, were: 1300 Zn, 570 Cu, 280 Pb, 45 Ni and 13 Cd. Soil samples collected from the surface horizon and composite leaf samples of cured tobacco were analyzed for total Zn, Cu, Mn, Fe, Pb, Ni and Cd concentrations. The soil samples were also examined for soil pH and DTPA extractable metals. Equations were generated using polynomic and stepwise regression analyses which described the relationships between total vs. DTPA extractable soil metals, and between DTPA soil and soil pH vs. plant metal concentrations, respectively. Significant increases were observed for both total and DTPA extractable metal concentrations for all metals, with all but total Mn and Ni being significant for linear and quadratic effects regarding sludge rates. However, linear relationships were found between DTPA extractable vs. total soil concentrations for all elements except Pb and Ni which were quadratic. Significant increases in plant Zn, Cu, Mn, Ni and Cd and decreases in Fe were observed with increased sludge rates. Plant Pb levels were unaffected by sludge applied Pb. Linear relationships were observed between plant Zn and Cd and DTPA soil metal levels: however, Mn and Cu levels were described by quadratic and cubic relationship, respectively. Relationships between plant Fe and Pb and DTPA extractable concentrations were nonsignificant. Additional safeguards to protect crop contamination from heavy metals such as Cd were discussed.     

Relation between heavy metal concentrations in salt marsh plants and soil

The aim of the research reported here was to investigate the relation between heavy metal concentrations in salt marsh plants, extractability of the metals from soil and some soil characteristics. In April 1987, Spartina anglica and Aster tripolium plants and soil were collected from four salt marshes along the Dutch coast. The redox potential of the soil between the roots of the plants and at bare sites was measured. Soil samples were oven-dried and analyzed for chloride concentration, pH, fraction of soil particles smaller than 63 microm (f < 63 microm), loss on ignition (LOI) and ammonium acetate and hydrochloric acid extractable Cd, Cu and Zn concentrations. The roots and shoots of the plants were analyzed for Cd, Cu and Zn. Because drying of the soil prior to chemical analysis might have changed the chemical speciation of the metals, and therefore the outcome of the ammonium acetate extraction, a second survey was performed in October 1990. In this survey A. tripolium plants and soil were collected from two salt marshes. Fresh and matched oven-dried soil samples were analyzed for water, ammonium acetate and diethylene triaminepentaacetic acid (DTPA) extractable Cd, Cu and Zn concentrations. The soil samples were also analyzed for f < 63 microm, LOI and total (HNO(3)/HCl digestion) metal concentrations. Soil metal concentrations were correlated with LOI. Drying prior to analysis of the soil had a significant effect on the extractability of the metals with water, ammonium acetate or DTPA. Plant metal concentrations significantly correlated only with some extractable metal concentrations determined in dried soil samples. However, these correlations were not consistently better than with total metal concentrations in the soil. It was concluded that extractions of metals from soil with water, ammonium acetate or DTPA are not better predictors for metal concentrations in salt marsh plants than total metal concentrations, and that a major part of the variation in metal concentrations in the plants cannot be explained by variation in soil composition.     

The effect of municipal sludge compost on the mobility and bioavailability of Cd in a sierozem-wheat system in an arid region northwest of China

The effect of sewage sludge on the mobility and the bioavailability of trace metals in plant-soil systems have aroused wide interested and been widely explored. Based on a wheat-cultivating experiment, the effect of municipal sludge compost (MSC) on the mobility and bioavailability of Cd in a soil-wheat system was studied. With the application of MSC, soil organic matter (SOM), total nitrogen (TN), and total phosphorus (TP) in the soil increased significantly, while concentrations of trace metals (Cu, Zn, Ni, Pb, Cd) were below the China’s minimum thresholds. The application of MSC could improve wheat growth. The application of MSC at the rate of 0.5 % had no significant effect on the chemical fraction distribution of Cd in soil. In two soil treatments, Cd mainly existed in the labile chemical fractions (exchangeable chemical fraction (EXCF) and carbonate chemical fraction (CABF)). However, the application of MSC could reduce accumulation of Cd by wheat. Cd contents in each part of the MSC-applied wheat were significantly less than that of non-MSC-applied wheat. In the tested soils, the extractable concentrations decreased in the order: EDTA > MgCl₂ ≈ NH₄OAc > DTPA. There were no significant differences between soil treatments in the amounts of extractable Cd when the extraction was done under neutral conditions, although significant differences were observed when the extraction was done under alkaline conditions. In this study, the DTPA extraction procedure provided a good indication of Cd bioavailability. Our results suggest that, in the short term at least, amending soils with MSC may benefit crop dry matter production while not increasing the risk of human exposure to Cd through consumption of wheat grown on MSC-amended soils.     

A comparison of physiologically based extraction test (PBET) and single-extraction methods for release of Cu, Zn, and Pb from mildly acidic and alkali soils

In vitro digestion test can be applied to evaluate the bioaccessibility of soil metals by measuring the solubility of the metals in synthetic human digestive tract. Physiologically based extraction test (PBET), composed of sequential digestion of gastric and intestinal phase, is one of the frequently used in vitro digestion tests. In this study, the PBET was chosen to determine the bioaccessibility of Cu, Zn, and Pb in 14 mildly acidic and alkali (pH 5.87–8.30) soils. The phytoavailability of Cu, Zn, and Pb in the same soils was also measured using six single-extraction methods (0.1 M HNO₃, 0.4 M HOAc, 0.1 M NaNO₃, 0.01 M CaCl₂, 0.05 M EDTA, and 0.5 M DTPA). The extraction efficiencies of the methods were compared. The PBET had a strong ability to extract metals from soil, which was much greater than neutral salt extraction and close to dilute acid and complex extraction in spite of the last 2 h neutral intestinal digestion. The amounts of bioaccessible Cu, Zn, and Pb in the gastric phase and in the gastrointestinal phase were both largely determined by the total content of soil Cu, Zn, and Pb. But the results of gastrointestinal digestion reflected more differences resulting from element and soil types than those of gastric digestion did. It was noticed that most of variations in the amounts of soil Cu, Zn, and Pb extracted by EDTA were well explained by the total soil Cu, Zn, and Pb, as same as the PBET. Moreover, the solubility of Cu, Zn, and Pb in the gastric phase and gastrointestinal phase were all positively linearly correlated with the results of EDTA. It was suggested that EDTA extraction can be used to predict the bioaccessibility of Cu, Zn, and Pb in mildly acidic and alkali (pH?>?5.8) soils, and the PBET and EDTA could be applied to measure, in a certain extent, the bioaccessibility and phytoavailability of Cu, Zn, and Pb in mildly acidic and alkali (pH?>?5.8) soils at the same time.     

Effects of EDTA and low molecular weight organic acids on soil solution properties of a heavy metal polluted soil

A pot experiment was conducted to study the effects of EDTA and low molecular weight organic acids (LMWOA) on the pH, total organic carbon (TOC) and heavy metals in the soil solution in the rhizosphere of Brassica juncea grown in a paddy soil contaminated with Cu, Zn, Pb and Cd. The results show that EDTA and LMWOA have no effect on the soil solution pH. EDTA addition significantly increased the TOC concentrations in the soil solution. The TOC concentrations in treatments with EDTA were significantly higher than those in treatments with LMWOA. Adding 3 mmol kg(-1) EDTA to the soil markedly increased the total concentrations of Cu, Zn, Pb and Cd in the soil solution. Compared to EDTA, LMWOA had a very small effect on the metal concentrations. Total concentrations in the soil solution followed the sequence: EDTA > citric acid (CA) approximately oxalic acid (OA) approximately malic acid (MA) for Cu and Pb; EDTA > MA > CA approximately OA for Zn; and EDTA > MA > CA > OA for Cd. The labile concentrations of Cu, Zn, Pb and Cd showed similar trends to the total concentrations.     

Distribution coefficients of potentially toxic elements in soils from the eastern Amazon

The solid-solution distribution or partition coefficient (Kd) is a measure of affinity of potentially toxic elements (PTE) for soil colloids. Kd plays a key role in several models for defining PTE guideline values in soils and for assessing environmental risks, and its value depends on edaphic and climatic conditions of the sites where the soils occur. This study quantified Kd values for Cd, Co, Cr, Cu, Hg, Ni, Pb, and Zn from representative soil samples from Brazil’s eastern Amazon region, which measures 1.2 million km². The Kd values obtained were lower than those set by both international and Brazilian environmental agencies and were correlated with the pH, Fe and Mn oxide content, and cationic exchange capacity of the soils. The following order of decreasing affinity was observed: Pb?>?Cu?>?Hg?>?Cr?>?Cd?≈?Co?>?Ni?>?Zn.     

Trace metals in surface sediments of the Taiwan Strait: geochemical characteristics and environmental indication

The concentration and geochemical fractionation of six trace metals related with environmental quality assessment, namely Cd, Cr, Cu, Ni, Pb, and Zn, in 30 surface sediments from both inshore and offshore areas of the Taiwan Strait were measured to investigate their distribution characteristics, evaluate their potential mobility, and assess their pollution status. The geoaccumulation index results indicated that, on average, the studied metals presented an order of Cd?>?Pb?>?Ni?>?Zn?>?Cu?>?Cr and were practically in uncontaminated status except Cd. The results of the sequential extraction analysis indicated that, on average, the studied metals were mostly accumulated in residual fraction except Cd whose concentration was the highest in the acid soluble fraction presenting a high risk to the environment, and their mobility decreased in the sequence of Cd?>?Pb?>?Ni?>?Cu?>?Zn?>?Cr. Based on the mean probable effect level quotients, the combination of the studied metals had an 8 % probability of being toxic at two sampling sites and had a 21 % probability of being toxic at the rest of sites. The spatial distribution of the studied metals in total concentrations and different geochemical fractions corroborated the previous findings about the possible sediment transportation routes in and around the Taiwan Strait.     

Influence of solution acidity and CaCl2 concentration on the removal of heavy metals from metal-contaminated rice soils

Soil washing is considered a useful technique for remediating metal-contaminated soils. This study examined the release edges of Cd, Zn, Ni, Cr, Cu or Pb in two contaminated rice soils from central Taiwan. The concentrations exceeding the trigger levels established by the regulatory agency of Taiwan were Cu, Zn, Ni and Cr for the Ho-Mei soil and Pb for the Nan-Tou soil. Successive extractions with HCl ranging from 0 to 0.2 M showed increased release of the heavy metals with declining pH, and the threshold pH value below which a sharp increase in the releases of the heavy metals was highest for Cd, Zn, and Ni (pH 4.6 to 4.9), intermediate for Pb and Cu (3.1 to 3.8) and lowest for Fe (2.1), Al (2.2) and Cr (1.7) for the soils. The low response slope of Ni and Cr particularly for the rice soils make soil washing with the acid up to the highest concentration used ineffective to reduce their concentrations to below trigger levels. Although soil washing with 0.1 M HCl was moderately effective in reducing Cu, Pb, Zn and Cd, which brought pH of the soils to 1.1+/-0.1 (S.D.), the concurrent release of large quantities of Fe and Al make this remediation technique undesirable for the rice soils containing high clay. Successive washings with 0.01 M HCl could be considered an alternative as the dissolution of Fe and Al was minimal, and between 46 to 64% of Cd, Zn, and Cu for the Ho-Mei soil and 45% of Pb in the Na-Tou soil were extracted after four successive extractions with this dilute acid solution. The efficacy of Cd extraction improved if CaCl2 was added to the acid solution. The correlation analysis revealed that Cr extracted was highly correlated (P < 0.001) with Fe extracted, whereas the Cu, Ni, Zn, Cd or Pb extracted was better correlated (P < 0.001) with Al than with Fe extracted. It is possible that the past seasonal soil flooding and drainage in the soils for rice production was conducive to incorporating Cr within the structure of Fe oxide, thereby making them extremely insoluble even in 0.2 M HCl solution. The formation of solid solution of Ni with Al oxide was also possible, making it far less extractable than Cd, Zn, Cu, or Pb with the acid concentrations used.     

Enhanced phytoextraction of Cu, Pb, Zn and Cd with EDTA and EDDS

Chemically enhanced phytoextraction has been proposed as an effective approach to removing heavy metals from contaminated soil through the use of high biomass plants. Using pot experiments, the effects of the application of EDTA, EDDS and citric acid on the uptake of Cu, Pb, Zn and Cd by corn (Zea mays L. cv. Nongda 108) and bean (Phaseolus vulgaris L. white bean) plants were studied. The results showed that EDDS was more effective than EDTA at increasing the concentration of Cu in corn and beans. The application of 5 mmol kg-1 soil EDDS to soil significantly increased concentrations of Cu in shoots, with maximum levels of 2060 and 5130 mg kg-1 DW in corn and beans, respectively, which were 45- and 135-fold higher than that in the corresponding control plants to which chelate had not been applied. Concentrations of Zn in shoots were also higher in the plants treated with EDDS than in those treated with EDTA. For Pb and Cd, EDDS was less effective than EDTA. The maximum Cu phytoextraction was found with the EDDS treatment. The application of EDTA and EDDS also significantly increased the shoot-to-root ratios of the concentrations of Cu, Pb, Zn and Cd in both plant species. The results of metal extraction with chelates showed that EDDS was more efficient at solubilizing Cu and Zn than EDTA, and that EDTA was better at solubilizing Pb and Cd than EDDS.     

The study of operating variables in soil washing with EDTA

This study discusses the operating variables for removal of metals from soils using EDTA, including the type of EDTA, reaction time, solution pH, dose, temperature, agitation, ultrasound and number of extractions. For As, Cd, Cu, Pb and Zn, the removal efficiency order was: H₄-EDTA > Na₂EDTA > (NH₄)₂EDTA. At low EDTA concentrations the removal increased progressively with increasing dose while above 0.4 mmol/g only small increases in extraction efficiency were observed. EDTA induced a two-step process including a rapid desorption within the first hour, and a gradual release in the following hours. The extraction efficiency of metals decreased with increasing pH in the range of 2-10. Consecutive extractions using low concentrations were more effective than a single extraction with concentrated EDTA if the same dose of EDTA was used.     

Use of scalp hair as indicator of human exposure to heavy metals in an electronic waste recycling area

Scalp hair samples were collected at an electronic waste (e-waste) recycling area and analyzed for trace elements and heavy metals. Elevated levels were found for Cu and Pb with geometric means (GMs) at 39.8 and 49.5 μg/g, and the levels of all elements were found in the rank order Pb > Cu ? Mn > Ba > Cr > Ni > Cd > As > V. Besides Cu and Pb, Cd (GM: 0.518 μg/g) was also found to be significantly higher compared to that in hair samples from control areas. Differences with age, gender, residence status and villages could be distinguished for most of the elements. The high levels of Cd, Cu and Pb were likely found to be originated from e-waste related activities, and specific sources were discussed. This study shows that human scalp hair could be a useful biomarker to assess the extent of heavy metal exposure to workers and residents in areas with intensive e-waste recycling activities.     

Partitioning and mobility behavior of metals in road dusts from national-scale industrial areas in Korea

In this study, we investigated the characteristics of heavy metal contamination in road dusts collected from industrial areas in Korea. A total of 12 sampling sites, including nine sites in three different industrial complexes (ICs), two IC vicinity areas and one background area, were selected for this study. The collected road dusts were divided into four categories. The heavy metals (Cd, Cu, Pb, Zn, and Ni) were extracted from the road dust by an aqua regia extraction method and analyzed by atomic absorption spectrometry. The highest concentrations of Cd, Cu, and Pb were identified in road dusts from areas near the non-ferrous metal IC, followed by those from the petrochemical IC. The petrochemical IC and the mechanical/shipbuilding IC showed the highest concentrations of Ni and Zn in their road dusts, respectively. The concentration of heavy metals in the road dusts collected from the IC vicinity areas, even those located in a rural environment, were very high. The concentration of heavy metals increased with decreasing particle size of the road dusts. This study also analyzed the mobility of the heavy metals in the road dusts using partial sequential extraction with the Tessier procedure. The order of mobility identified, based on exchangeable and carbonate fractions of the heavy metals, was Cd > Zn > Pb > Cu > Ni.     

Phytoextraction of metals from a multiply contaminated soil by Indian mustard

The effects of nitrilotriacetate (NTA) and citric acid applications on metal extractability from a multiply metal-contaminated soil, as well as on their uptake and accumulation by Indian mustard (Brassica juncea) were investigated. Desorption of metals from the soil increased with chelate concentration, NTA being more effective than citric acid in solubilising the metals. Plants were grown in a sandy soil collected from a contaminated field site and polluted by Cd, Cr, Cu, Pb and Zn. After 43 days of plant growth, pots were amended with NTA or citric acid at 5 mmol kg-1 soil. Control pots were not treated with any chelate. Harvest of plants was performed 1 week after chelate addition. Soil water-, NH4NO3- and DTPA-extractable Cd, Cu, Pb and Zn fractions were enhanced only in the presence of NTA. In comparison to unamended plants, Indian mustard shoot dry weights suffered significant reductions following NTA application. NTA treatment increased shoot metal concentrations by a factor of 2-3, whereas citric acid did not induce any difference compared to the control. Chromium was detected in the above-ground tissues only after NTA amendment. Due to differences in dry matter yield, a significant enhancement of metal uptake was observed in NTA-treated plants for Cu and Zn.     

Potentially toxic element fractionation in technosoils using two sequential extraction schemes

This study reports the chemical fractionation of several potentially toxic elements (Zn, Pb, Cd, As, and Sb) in contaminated technosoils of two former smelting and mining areas using two sequential extraction schemes. The extraction schemes used in this study were the Tessier’s scheme and a modified BCR scheme. The fractions were rearranged into four equivalent fractions defined as acid soluble, reducible, oxidizable, and residual to compare the results obtained from two sequential extraction schemes. Surface soils were samples from a waste landfill contaminated with Zn, Pb, and Cd located at Mortagne-du-Nord (MDN; North France) and from a settling basin contaminated with PTE such as As, Pb, and Sb located at La Petite Faye (LPF; Limoges, France). The study of the Zn, Pb, Cd, As, and Sb partitioning in the acid soluble, reducible, oxidizable, and residual fractions of the technosoils revealed that Zn, Cd, and Pb were mainly associated with the acid soluble and reducible fractions for MDN site, while As, Sb, and Pb were associated with residual fraction for LPF site. Fractionation results indicate that the percentages of Zn, Pb, Cd, As, and Sb extracted in Fe–Mn oxide bound fraction of Tessier’s scheme were always higher than those extracted by modified BCR scheme. This may be attributed to the stronger Tessier’s scheme conditions used to extract this fraction. In contrast the percentages of Zn, Pb, Cd, As, and Sb extracted in the organic fraction of the modified BCR scheme were always higher than those of the Tessier’s scheme. The order of mobility of PTE was as follows: Cd?>?Zn?>?Pb in MDN site and As?>?Sb?>?Pb in LPF site. PTE were distributed in all soil fractions, with the most relevant enrichments in extractable and residual fractions. A significant amount of Cd, Pb, and Zn were rather mobile, which suggests that these elements can be readily available to plants and soil organisms.     

Earthworms as biological monitors of cadmium, copper, lead and zinc in metalliferous soils

Earthworms (Lumbricus rebellus and Dendrodrilus rubidus) were sampled from one uncontaminated and fifteen metal-contaminated sites. Significant positive correlations were found between the earthworm and 'total' (conc. nitric acid-extractable) soil Cd, Cu, Pb and Zn concentrations (data log1) transformed). The relationships were linear, and the accumulation patterns for both species were similar when a single metal was considered, even though there were species difference in mean metal concentrations. Generally, the earthworm Cd concentration exceeded that of the soil; by contrast, the worm Pb concentration was lower than the soil Pb concentration in all but one (acidic, low soil Ca) site. Our observations suggest that Cu and Zn accumulation may be physiologically regulated by both species. Total-soil Cd explained 82-86% of the variability (V2) in earthworm Cd concentration; 52-58% of worm Pb and worm Zn concentrations were explained by the total-soil concentrations of the respective metals. Total-soil Cu explained only 11-32% of the worm Cu concentration. The effect of soil pH, total Ca concentration, cation-exchange capacity (CEC) and organic carbon on metal accumulation by L. rubellus and D. rubidus was investigated by multiple regression analysis. Soil pH (coupled with CEC) and soil Ca had a major influence on Pb accumulation (V2 of worm Pb increased to 77-83%), and there was some evidence that Cd accumulation may be suppressed in extremely organic soils. The edaphic factors investigated had no effect on Cu or Zn accumulation by earthworms. In the context of biomonitoring, it is proposed that earthworms have a potential in a dual role: (1) as 'quantitative' monitors of total-soil metal concentrations (as shown for Cd); and (2) as estimators of 'ecologically significant' soil metal, integrating the effects of edaphic factors (as shown for Pb).     

Application of different single extraction procedures for assessing the bioavailability of heavy metal(loid)s in soils from overlapped areas of farmland and coal resources

Heavy metal(loid) extraction from soils in overlapped areas of farmland and coal resources (OAFCR) is crucial in understanding heavy metal bioavailability in soil and the subsequent risks to crops and consumers. However, limited attention has been paid to the extraction procedure of heavy metal(loid)s in OAFCR soils in the research. This study therefore explored different single and mixed extraction procedures, such as acetic acid (HOAc), citric acid, ammonium bicarbonate-diethylenetriaminepentaacetic acid (AB-DTPA), ethylene diamine tetraacetic acid + ammonium acetate (EDTA+NH₄OAc), and total digestion (HNO₃-HClO₄-HF) to determine the bioavailability of As, Cd, Cr, Cu, Pb, and Zn in OAFCR soil in Xuzhou, China. The results showed the metal(loid) extraction capacity from soil of the different procedures could be ranked as AB-DTPA > EDTA+NH₄OAc > HOA_C > citric acid. The transfer ability of heavy metal(loid)s from soil to wheat tissues and from wheat roots to aerial parts was analyzed by calculating the bioconcentration factor and transfer factor, respectively. Transfer factors of all metal(loid)s were < 1 except Cr whose transfer factor from root to shell and straw were > 1. It is suspected that foliar uptake plays a dominant role in Cr uptake. Correlation analysis between the bioavailability of heavy metal(loid)s in soil and uptake in respective wheat tissues was performed to recommend the best extraction procedures for different studies. The results show that AB-DTPA extraction is recommended for Cu uptake to wheat roots, straws, shells and grains, Zn uptake to roots, and Cd uptake to roots and straws.

     

The use of poplar during a two-year induced phytoextraction of metals from contaminated agricultural soils

The efficiency of poplar (Populus nigra L.xPopulus maximowiczii Henry.) was assessed during a two-year chemically enhanced phytoextraction of metals from contaminated soils. The tested metal mobilizing agents were EDTA (ethylenediaminetetraacetic acid) and NH4Cl. EDTA was more efficient than chlorides in solubilizing metals (especially Pb) from the soil matrix. The application of chlorides only increased the solubility of Cd and Zn. However, the increased uptake of metals after the application of higher concentrations of mobilizing agents was associated with low biomass yields of the poplar plants and the extraction efficiencies after the two vegetation periods were thus comparable to the untreated plants. Additionally, the application of mobilizing agents led to phytotoxicity effects and increased mobility of metals. Higher phytoextraction efficiencies were observed for Cd and Zn compared to Pb and Cu. Poplars are therefore not suitable for chemically enhanced phytoextraction of metals from severely contaminated agricultural soils.     

The solid-solution partitioning of heavy metals (Cu,Zn, Cd,Pb) in upland soils of England and Wales

Ninety-eight surface soils were sampled from the uplands of England and Wales, and analysed for loss-on-ignition (LOI), and total and dissolved base cations, Al, Fe, and trace heavy metals (Cu, Zn, Cd, Pb). The samples covered wide ranges of pH (3.4-8.3) and LOI (9-98%). Soil metal contents measured by extraction with 0.43 mol l-1 HNO3 and 0.1 mol l-1 EDTA were very similar, and generally lower than values obtained by extraction with a mixture of concentrated nitric and perchloric acids. Total heavy metal concentrations in soil solution depend positively upon soil metal content and [DOC], and negatively upon pH and LOI, values of r2 ranging from 0.39 (Cu) to 0.81 (Pb). Stronger correlations (r2=0.76-0.95) were obtained by multiple regression analysis involving free metal ion (Cu2+, Zn2+, Cd2+, Pb2+) concentrations calculated with the equilibrium speciation model WHAM/Model VI. The free metal ion concentrations depend positively upon MHNO3 and negatively upon pH and LOI. The data were also analysed by using WHAM/Model VI to describe solid-solution interactions as well as solution speciation; this involved calibrating each soil sample by adjusting the content of "active" humic matter to match the observed soil pH. The calibrated model provided fair predictions of total heavy metal concentrations in soil solution, and predicted free metal ion concentrations were in reasonable agreement with the values obtained from solution-only speciation calculations.     

Effect of ageing on the availability of heavy metals in soils amended with compost and biochar: evaluation of changes in soil and amendment properties

Remediation strategies using soil amendments should consider the time dependence of metal availability to identify amendments that can sustainably reduce available pollutant concentrations over time. Drying-wetting cycles were applied on amendments, soils and soil + amendment mixtures, to mimic ageing at field level and investigate its effect on extractable Cd, Cu, Ni, Pb and Zn concentrations from three contaminated soils. The amendments investigated were municipal waste organic compost and biochars. The amendments, soils and mixtures were characterised by their physicochemical properties at different ageing times. The amendments were also characterised in terms of sorption capacity for Cd and Cu. The sorption capacity and the physicochemical properties of the amendments remained constant over the period examined. When mixed with the soils, amendments, especially the compost, immediately reduced the extractable metals in the soils with low pH and acid neutralisation capacity, due to the increase in pH and buffering capacity of the mixtures. The amendments had a relatively minor impact on the metal availability concentrations for the soil with substantially high acid neutralisation capacity. The most important changes in extractable metal concentrations were observed at the beginning of the experiments, ageing having a minor effect on metal concentrations when compared with the initial effect of amendments.

     

Changes in speciation and leaching behaviors of heavy metals in dredged sediment solidified/stabilized with various materials

Solidification/stabilization (S/S) of sediments is frequently used to treat contaminants in dredged sediments. In this study, sediment collected from the Pearl River Delta (China) was solidified/stabilized with three different kinds of functional materials: cement, lime and bentonite. Lime primarily acted via induced increases in pH, while cements stabilization occurred through their silicate-based systems and the main function of bentonite was adsorption. The speciation and leaching behaviors of specific heavy metals before and after S/S were analyzed and the results showed that the residual speciation of Cd, Cr, Ni, Pb and Zn increased in all treatments except for Cu, as the exchangeable speciation, carbonate-bound speciation and Fe-Mn-oxide-bound speciation of Cu (all of which could be stabilized) were less than 2 % of the total amount. Pb leaching only decreased when pH increased, while the mobility of Cr and Ni only decreased in response to the silicate-based systems. The leached portion of the Fe-Mn-oxide-bound speciation followed the order Zn?>?Cu?>?Ni/Cd?>?Pb?>?Cr. The leached portion of organic-matter-bound species was less than 4 % for Cd, Cr, Ni and Pb, but 35.1 % and 20.6 % for Cu and Zn, respectively.