过硫酸钾去除水中的TCE

以地水中的氯代烃污染物三氯乙烯(TCE)为目标污染物,以过硫酸钾溶液为氧化剂,探讨了不同条件下过硫酸钾对TCE的去除效果。实验结果表明,在40℃,过硫酸钾初始浓度为2.43 g/L条件下,反应2 h后,TCE的去除率就可达到96.8%;过硫酸钾对TCE的去除符合一级反应动力学方程,速率常数(K)为1.3364 h-1,半衰期(t1/2)为0.51 h;过硫酸钾对TCE的去除速率在pH为中性附近时最大,其后无论pH升高或降低去除速率均减小;受温度和pH影响较明显,并且反应温度越高,受pH的影响越明显;随离子强度的增加而减小;反应活化能为119.6 kJ/mol;过硫酸钾溶于水生成过硫酸根离子(S2O28-),S2O28-会进一步生成硫酸根自由基(SO4-.),在碱性条件下,SO4-.与OH-反应会进一步生成羟基自由基(.OH)。过硫酸钾对于TCE的去除主要源自SO4-.和.OH的强氧化性。     

Supported Pd/Sn bimetallic nanoparticles for reductive dechlorination of aqueous trichloroethylene

A Pd/Sn bimetallic nanoparticles resin (nano-Pd/Sn/resin) was successfully synthesized for reductive transformation of aqueous trichloroethylene (TCE). The physicochemical properties of the prepared resin were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, N(2) isothermal sorption at and X-ray photospectroscopy. The surface-area-normalized rate constants (k(SA)) of Sn particles in the nanoscale range (50-100 nm) were 4.5 times larger than the k(SA) for powdered Sn (0.04 mm). After depositing 1 wt% Pd onto nano-Sn surface, k(SA) was further enhanced by about a factor of 2. Groundwater constituents such as sulfide nitrate and dissolved oxygen had significant negative effects on the rate of TCE degradation by the nano-Pd/Sn/resin. A wet-chemical method regeneration method was observed to effectively restore the reactivity of the poisoned nano-Pd/Sn/resin after dipping in sulfide solution for 2d. In all cases, less than 0.5% of the degraded TCE appeared as chlorinated byproducts including the three dichloroethene isomers. The nano-Pd/Sn/resin technique performs well in transforming TCE into nontoxic hydrocarbons, as compared with other published methods.     

Fe3O4／Ag磁性纳米颗粒去除水中的铅离子

采用水相共沉淀法制备小尺寸磁性Fe3O4纳米颗粒,以没食子酸作为还原剂和表面修饰剂,还原Ag[（NH3）2]’制备出Fe3O4／Ag磁性纳米颗粒。研究该磁性纳米颗粒对水溶液中铅离子的吸附行为,研究结果表明,pH为7．0,吸附温度30℃时可得到最好的处理效果,铅的去除率可达99．7％以上,Fe3O4／Ag颗粒吸附行为符合二级动力学模型（R2〉0．99）。该磁性纳米颗粒经过多次再生处理后,仍具有很好的吸附效果,表明Fe3O4／Ag在水处理方面拥有良好的应用前景。     

CS-Fe和CS-Fe/Ni的制备及其用于去除钴离子

以氯化铁为铁源,硼氢化钠为还原剂,壳聚糖为稳定剂,采用液相还原法制备壳聚糖稳定纳米铁（CS-Fe）;并以氯化铁为铁源,硫酸镍为镍源,硼氢化钠为还原剂,壳聚糖为稳定剂,采用液相还原共沉淀法制备壳聚糖稳定纳米铁镍（CS-Fe/Ni）。通过SEM、EDS、XRD、FT-IR等表征手段,对所制备的CS-Fe和CS-Fe/Ni的形貌及微观结构进行表征,并以Co²⁺为目标去除物评价CS-Fe和CS-Fe/Ni的反应活性。初步研究表明,制成的CS-Fe含有单质纳米铁,颗粒多数以30~90 nm球形颗粒为主;而CS-Fe/Ni材料中含有纳米铁镍,颗粒多数以30~60 nm球形颗粒为主;在相同的实验条件下,反应60 min,CS-Fe/Ni对Co²⁺的去除率高达100%,但是CS-Fe仅为88%,即CS-Fe/Ni对Co²⁺的去除率比CS-Fe高。     

Dechlorination of chlorinated hydrocarbons by bimetallic Ni/Fe immobilized on polyethylene glycol-grafted microfiltration membranes under anoxic conditions

In this study, the dechlorination of chlorinated hydrocarbons including trichloroethylene (TCE), tetrachloroethylene (PCE) and carbon tetrachloride (CT) by bimetallic Ni/Fe nanoparticles immobilized on four different membranes was investigated under anoxic conditions. Effects of several parameters including the nature of membrane, initial concentration, pH value, and reaction temperature on the dechlorination efficiency were examined. The scanning electron microscopic images showed that the Ni/Fe nanoparticles were successfully immobilized inside the four membranes using polyethylene glycol as the cross-linker. The agglomeration of Ni/Fe were observed in poly(vinylidene fluoride), Millex GS and mixed cellulose ester membranes, while a relatively uniform distribution of Ni/Fe was found in nylon-66 membrane because of its hydrophilic nature. The immobilized Ni/Fe nanoparticles exhibited good reactivity towards the dechlorination of chlorinated hydrocarbons, and the pseudo-first-order rate constant for TCE dechlorination by Ni/Fe in nylon-66 were 3.7-11.7 times higher than those in other membranes. In addition, the dechlorination efficiency of chlorinated hydrocarbons followed the order TCE > PCE > CT. Ethane was the only end product for TCE and PCE dechlorination, while dichloromethane and methane were found to be the major products for CT dechlorination, clearly indicating the involvement of reactive hydrogen species in dechlorination. In addition, the initial rate constant for TCE dechlorination increased upon increasing initial TCE concentrations and the activation energy for TCE dechlorination by immobilized Ni/Fe was 34.9 kJ mol⁻¹, showing that the dechlorination of TCE by membrane-supported Ni/Fe nanoparticles is a surface-mediated reaction.     

生物炭负载羧甲基纤维素钠稳定化纳米铁对水中六价铬的去除

利用液相还原法,通过先负载再包裹的方式制备了4种不同炭铁质量比的生物炭负载羧甲基纤维素钠稳定化纳米铁(BC-nZVI-CMC)材料,并将其用于对水中Cr(Ⅵ)的去除,使用扫描电镜、X射线衍射和傅里叶红外等技术对BC-nZVI-CMC的结构与性质进行了表征。结果表明：BC-nZVI-CMC具有较好的分散性,粒径为纳米级且被CMC完全包覆,抗氧化能力得到较大提升,可有效去除水中Cr(Ⅵ);投加1 g·L⁻¹的BC-nZVI-CMC对含有30 mg·L⁻¹的Cr(Ⅵ)去除率达99.83%;pH越小,越有利于BC-nZVI-CMC对水中Cr(Ⅵ)的去除,最高去除率可达100%;BC-nZVI-CMC的抗氧化能力明显高于商品纳米铁和生物炭负载纳米铁;含有8 g·L⁻¹ C/Fe=1∶1的BC-nZVI-CMC对电镀废水中Ni、Zn、Cu、总铬、Cr(Ⅵ)的去除率可达39.60%、91.70%、100%、91.69%、100%。上述研究结果对水中Cr(Ⅵ)去除新技术的开发有重要的参考价值。     

Discoloration of methylene blue and wastewater from a plant by a Fe/Cu bimetallic system

Using a Fe/Cu bimetallic system (Fe/Cu system), the discoloration of both methylene blue in aqueous solution and the colored wastewater from a plant was investigated under the anaerobic condition in batch or continuous reactors. Results show that the Fe/Cu system effectively removed the color with over 88% of color removal efficiency for both methylene blue solution and the wastewater from the plant in batch test. Color removal efficiencies increased rapidly with Fe/Cu dosage and reaction time, respectively, at initial time and slowly to stable values. Optimum pH was neutral range. In addition, in continuous test it also removed the color of the wastewater from the plant with 63% of discoloring efficiency under the condition of 2 h of hydraulic retention time and neutral range of pH (7.0-8.3). High discoloring efficiencies with low chemical oxygen demand removal efficiencies were found in all experiments. The reduction of chromophores in pollutants was the main mechanism of the discoloration in the Fe/Cu system.     

支撑气膜法脱除/回收垃圾渗滤液中氨氮简

利用由微孔疏水性聚丙烯中空纤维制成的工业级膜组件对垃圾渗滤液中氨氮进行支撑气膜法脱除研究,考察了泡沫分离-石灰絮凝等预处理技术对垃圾渗滤液表面张力及COD值的处理效果,在此基础上研究了物料因素和操作因素对膜传质性能的影响,并对该工艺的长期操作稳定性进行了研究。实验结果表明该预处理技术不仅可显著提高垃圾渗滤液的表面张力,还可大大降低其色度和COD值。当进料流量为100 L/h、进料氨氮浓度为1 000~3 000 mg/L、硫酸吸收液流量为200 L/h、硫酸浓度为6%~10%、温度为20~30℃时,支撑气膜过程（两级膜组件串联）可有效脱除垃圾渗滤液中99%以上的氨氮,同时得到含10%~15%硫酸铵的水溶液作为副产品。工业级支撑气膜组件在连续运行的2个月内保持了良好的传质稳定性。     

支撑气膜法脱除／回收垃圾渗滤液中氨氮

利用由微孔疏水性聚丙烯中空纤维制成的工业级膜组件对垃圾渗滤液中氨氮进行支撑气膜法脱除研究,考察了泡沫分离．石灰絮凝等预处理技术对垃圾渗滤液表面张力及COD值的处理效果,在此基础上研究了物料因素和操作因素对膜传质性能的影响,并对该工艺的长期操作稳定性进行了研究。实验结果表明该预处理技术不仅可显著提高垃圾渗滤液的表面张力,还可大大降低其色度和COD值。当进料流量为100L／h、进料氨氮浓度为1000～3000mg／L、硫酸吸收液流量为200L／h、硫酸浓度为6％～10％、温度为20～30℃时,支撑气膜过程（两级膜组件串联）可有效脱除垃圾渗滤液中99％以上的氨氮,同时得到含10％～15％硫酸铵的水溶液作为副产品。工业级支撑气膜组件在连续运行的2个月内保持了良好的传质稳定性。     

Removal of Pb(II) and Cd(II) ions from water by Fe and Ag nanoparticles prepared using electro-exploding wire technique

Purpose

This work aimed at investigating the adsorption of lead and cadmium onto Fe and Ag nanoparticles for use as a water contaminant removal agent as a function of particle type, sorbent concentration, and contact time.

Methods

Fe and Ag spherical nanoparticles were prepared in water by the lab-made electro-exploding wire (EEW) system and were investigated for their structure properties. Adsorption experiments were carried out at room temperature and pH 8.3 water solutions.

Results

The removal/adsorption of both Pb(II) and Cd(II) ions was found to be dependent on adsorbent dosage and contact time. Pb(II) adsorption onto Fe and Ag nanoparticles showed more or less similar efficiency and behavior. The kinetic data for the adsorption process obeyed pseudo second-order rate equations. The calculated equilibrium adsorption capacities (q _e) were 813 and 800 mg/g for Pb sorption onto Fe and Ag nanoparticles, respectively. Cd(II) ion adsorption onto Fe nanoparticles obeyed pseudo second-order rate equations with q _e equal to 242 mg/g, while their adsorption onto Ag nanoparticles obeyed pseudo first-order rate equations with q _e of 794 mg/g. The calculated q _es are in quite agreement with the experimental values. The removal/uptake mechanisms of metal ions involved interaction between the metal ion and the oxide/hydroxyl layer around the spherical metallic core of the nanoparticle in water medium.

Conclusion

Fe and Ag nanoparticles prepared using the EEW technique exhibited high potentials for the removal of metal ions from water with very high adsorption capacities, suggesting that the EEW technique can be enlarged to generate nanoparticles with large quantities for field or site water purification.     

Hydrodechlorination of polychlorinated biphenyls in contaminated soil from an e-waste recycling area,using nanoscale zerovalent iron and Pd/Fe bimetallic nanoparticles

Soil pollution by polychlorinated biphenyls (PCBs) arising from the crude disposal and recycling of electronic and electrical waste (e-waste) is a serious issue, and effective remediation technologies are urgently needed. Nanoscale zerovalent iron (nZVI) and bimetallic systems have been shown to promote successfully the destruction of halogenated organic compounds. In the present study, nZVI and Pd/Fe bimetallic nanoparticles synthesized by chemical deposition were used to remove 2,2′,4,4′,5,5′-hexachlorobiphenyl from deionized water, and then applied to PCBs contaminated soil collected from an e-waste recycling area. The results indicated that the hydrodechlorination of 2,2′,4,4′,5,5′-hexachlorobiphenyl by nZVI and Pd/Fe bimetallic nanoparticles followed pseudo-first-order kinetics and Pd loading was beneficial to the hydrodechlorination process. It was also found that the removal efficiencies of PCBs from soil achieved using Pd/Fe bimetallic nanoparticles were higher than that achieved using nZVI and that PCBs degradation might be affected by the soil properties. Finally, the potential challenges of nZVI application to in situ remediation were explored.     

Removal of arsenic from water by electrocoagulation

In the present study electrocoagulation (EC) has been evaluated as a treatment technology for arsenite [As(III)] and arsenate [As(V)] removal from water. Laboratory scale experiments were conducted with three electrode materials namely, iron, aluminum and titanium to assess their efficiency. Arsenic removal obtained was highest with iron electrodes. EC was able to bring down aqueous phase arsenic concentration to less than 10 microgl(-1) with iron electrodes. Current density was varied from 0.65 to 1.53 mAcm(-2) and it was observed that higher current density achieved rapid arsenic removal. Experimental results at different current densities indicated that arsenic removal was normalized with respect to total charge passed and therefore charge density has been used to compare the results. Effect of pH on arsenic removal was not significant in the pH range 6-8. Comparative evaluation of As(III) and As(V) removal by chemical coagulation (with ferric chloride) and electrocoagulation has been done. The comparison revealed that EC has better removal efficiency for As(III), whereas As(V) removal by both processes was nearly same. The removal mechanism of As(III) by EC seems to be oxidation of As(III) to As(V) and subsequent removal by adsorption/complexation with metal hydroxides generated in the process.     

Fe3O4/Ag磁性纳米颗粒去除水中的铅离子

采用水相共沉淀法制备小尺寸磁性Fe₃O₄纳米颗粒,以没食子酸作为还原剂和表面修饰剂,还原Ag[(NH₃)₂]⁺制备出Fe₃O₄/Ag磁性纳米颗粒。研究该磁性纳米颗粒对水溶液中铅离子的吸附行为,研究结果表明,pH为7.0,吸附温度30℃时可得到最好的处理效果,铅的去除率可达99.7%以上,Fe₃O₄/Ag颗粒吸附行为符合二级动力学模型(R² > 0.99)。该磁性纳米颗粒经过多次再生处理后,仍具有很好的吸附效果,表明Fe₃O₄/Ag在水处理方面拥有良好的应用前景。     

Fe/Mg负载改性竹炭去除水中的氨氮

用MgCl2溶液、FeCl3溶液浸渍对竹炭进行改性,以BET比表面积和SEM-EDS对其进行表征。通过静态吸附实验,研究改性竹炭对氨氮的吸附特性以及吸附时间、初始氨氮浓度、pH值和磷存在等因素对改性竹炭吸附氨氮能力的影响。实验表明,用氯化镁和氯化铁对竹炭进行改性,可使竹炭表面化学性质和物理结构特性同时发生变化;未改性竹炭与改性竹炭对氨氮的吸附量大小依次为:BC< MBC< FBC< FMBC;竹炭在吸附时间为24 h时基本达到吸附平衡,吸附过程符合准二级动力学方程;改性竹炭对氨氮的吸附等温方程与Freundlich模型拟合较好;改性竹炭对氨氮吸附的最佳pH为5;磷存在可使改性竹炭对氨氮的吸附量显著增加。     

天然橄榄石对水体铜绿微囊藻的去除效果

为开发安全、高效、廉价的水华控制技术,选择铝土矿、磷铁矿、黄铁矿、铬铁矿及橄榄石等10种天然矿物材料,以水体铜绿微囊藻为研究对象,通过跟踪测定其叶绿素a的变化,研究了天然矿物对水体铜绿微囊藻去除特性,并探讨了天然橄榄石去除铜绿微囊藻的影响因素及去除机理。结果表明：相同条件下天然橄榄石具有最高的除藻能力;矿物用量及藻密度对橄榄石除藻过程影响最大,其次为pH及水温,光强影响最小;当橄榄石浓度为1.5 g·L^‒1,藻密度<1.7×10⁶ cells·mL^‒1、水温15 ℃、反应介质为弱酸性或中性(pH 5~7)时,吸附1 h后,叶绿素a去除率高于96%。进一步分析可知,天然橄榄石主要通过静电作用对铜绿微囊藻进行吸附,进而使藻细胞絮凝沉降,部分藻细胞破裂分解,同时天然橄榄石在反应过程中吸附培养基中的营养盐,造成藻细胞营养缺少,从而对藻细胞的生长造成一定的抑制作用。     

Removal of nanoparticles from CMP wastewater by magnetic seeding aggregation

CMP wastewaters have high solids content resulted from abrasive nanoparticles. Tremendous amount of ultrapure water consumption also makes the removal of nanoparticles from CMP wastewaters an important issue. Magnetic seeding aggregation of silica nanoparticles from the oxide CMP wastewater is studied in this work. Magnetite nanoparticles were synthesized and used as seeding particles. The turbidity of the CMP wastewater was reduced from 110 NTU to 7 NTU when solution pH was 6 and no addition of salt. This is because silica and magnetite nanoparticles were highly oppositely charged and the aggregation between silica and magnetite nanoparticles was achieved by electrostatic attractions. When the seeded wastewater was placed in a magnetic field strength higher than 800 G, the turbidity of the CMP wastewater was reduced to 1 NTU, which was clearer than the CMP wastewater treated by many other technologies.     

自养反硝化菌对硝酸盐氮去除动力学及影响因素研究

为更经济有效地去除污水中的硝酸盐,从兼性污泥中分离获得6株能氧化单质硫和还原硝酸盐的自养反硝化菌。根据各菌株的降解曲线筛选出优势菌种N-I,并研究影响菌株N-I降解性能的环境因素,如pH、温度、碳源及硝酸盐的降解动力学。实验表明,菌株N-I对硝酸盐的降解符合一级反应动力学方程,反应的半衰期t_1/2为1.42 h,反应速率常数为0.488 h^-1。最佳反应pH=7,最佳反应温度为30℃,最佳NaHCO₃浓度为大于或等于2.5 g/L。     

纳米钯?铝双金属对水中3-氯酚的脱氯降解研究

采用置换沉积法制备了纳米钯/铝双金属催化剂,氢解还原去除水相中难降解有毒有机物3-氯酚(3-CP),考察了溶液pH、钯负载量、纳米钯/铝双金属投加量、反应温度对脱氯效果的影响并解析相关反应机制。结果表明:(1)初始pH 3.0时,沉积液中93.25%(质量分数,下同)～96.67%的钯可有效负载于铝材上。(2)在pH为3.0、纳米钯/铝双金属投加量为2g/L、钯负载量为1.16%(质量分数)、反应温度为25℃下降解初始摩尔浓度为0.389mmol/L的3-CP,反应终了时脱氯率在99%以上。利用纳米钯/铝双金属降解氯代有机污染物具有高效低耗的优势,在实际应用上具有较好的前景。     

壳聚糖对地表水中污染物的净化作用

综述了壳聚糖絮凝剂对地表水中悬浮物、天然有机物(NOM)、人工合成有机物(SOCs)、藻类的去除和对细菌的抑制及残留铝的削减作用。壳聚糖在地表水净化中具有一定的应用价值。     

高岭土负载纳米铁镍双金属去除水中偶氮染料直接耐晒黑G

采用液相还原法制备焙烧高岭土负载纳米铁镍双金属（CK-Fe/Ni）。考察了在不同条件下,如pH、投加量、初始浓度、温度等,对负载型纳米铁镍双金属降解水中偶氮染料直接耐晒黑G的影响及动力学研究。结果表明：在pH=9.49、温度为30℃、负载型纳米铁镍双金属的投加量为1.05 g/L、搅拌速度为60 r/min,经过20 min反应后,负载型纳米铁镍双金属降解水中偶氮染料直接耐晒黑G的去除率达到了99.98%。吸附和电镜表征结果表明,作为载体的焙烧高岭土起着吸附直接耐晒黑G和分散纳米铁镍双金属颗粒的作用导致反应活性提高。降解动力学数据表明,负载型纳米铁镍双金属对直接耐晒黑G的降解过程符合伪一级反应动力学规律,速率常数k随负载型纳米铁镍双金属的投加量的增加而提高,表观活化能为19.72 kJ/mol。最后,利用高岭土负载纳米铁镍双金属对废水处理,结果表明,负载型纳米铁镍双金属在实际废水中对直接耐晒黑G的去除率达到了99.98%。