Remediation of metal-contaminated soils with the addition of materials--part I: characterization and viability studies for the selection of non-hazardous waste materials and silicates

Contamination episodes in soils require interventions to attenuate their impact. These actions are often based on the addition of materials to increase contaminant retention in the soil and to dilute the contaminant concentration. Here, non-hazardous wastes (such as sugar foam, fly ash and a material produced by the zeolitization of fly ash) and silicates (including bentonites) were tested and fully characterized in the laboratory to select suitable materials for remediating metal-contaminated soils. Data from X-ray fluorescence (XRF), N₂ adsorption/desorption isotherms, X-ray diffraction (XRD) and scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM-EDX) analyses revealed the chemical composition, specific surface area and the phases appearing in the materials. A pH titration test allowed the calculation of their acid neutralization capacity (ANC). The metal sorption and desorption capacities of the waste materials and silicates were also estimated. Sugar foam, fly ash and the zeolitic material were the best candidate materials. Sugar foam was selected because of its high ANC (17 000 meq kg⁻¹), and the others were selected because of their larger distribution coefficients and lower sorption reversibilities than those predicted in the contaminated soils.     

Comparison of CaO’s effect on the fate of heavy metals during thermal treatment of two typical types of MSWI fly ashes in China

Both grate and fluidized bed incinerators are widely used for MSW incineration in China. CaO addition for removing hazardous emissions from MSWI flue gas changes the characteristics of fly ash and affects the thermal behavior of heavy metals when the ash is reheated. In the present work, two types of MSWI fly ashes, sampled from both grate and fluidized bed incinerators respectively, were thermal treated at 1023–1323 K and the fate of heavy metals was observed. The results show that both of the fly ashes were rich in Ca and Ca-compounds were the main alkaline matter which strongly affected the leaching behavior of heavy metals. Ca was mostly in the forms of Ca(OH)₂ and CaCO₃ in the fly ash from grate incinerator in which nascent fly ash particles were covered by Ca-compounds. In contrast, the content of Ca was lower in the fly ash from fluidized bed incinerator and Ca was mostly in the form of CaSO₄. Chemical reactions among Ca-compounds caused particle agglomeration in thermal treated fly ash from grate incinerator, restraining the heavy metals volatilization. In thermal treated fly ash from fluidized bed incinerator, Ca was converted into aluminosilicates especially at 1323 K which enhanced heavy metals immobilization, decreasing their volatile fractions as well as leaching concentrations. Particle agglomeration hardly affected the leaching behavior of heavy metals. However, it suppressed the leachable-CaCrO₄ formation and lowered Cr leaching concentration.     

Continuous CO2 capture and MSWI fly ash stabilization, utilizing novel dynamic equipment

Novel dynamic equipment with gas in and out continuously was developed to study the capture capacity of CO₂. Municipal solid waste incineration (MSWI) fly ash has a high capture rate of CO₂ in CO₂-rich gas. Fly ash can sequester pure CO₂ rapidly, and its capacity is 16.3 g CO₂/100 g fly ash with no water added and 21.4 g CO₂/100 g fly ash with 20% water added. For simulated incineration gas containing 12% CO₂, the capture rate decreased and the capacity was 13.2 g CO₂/100 g fly ash with no water added and 18.5 g CO₂/100 g fly ash with 20% water added. After accelerated carbonation, the C and O contents increased, indicating CO₂ capture in the fly ash; CO₂ combines with Ca(OH)₂ to form CaCO₃, which increased the CaCO₃ content from 12.5 to 54.3%. The leaching of Pb markedly decreased from 24.48 to 0.111 mg/L.     

Migration and leaching risk of extraneous antimony in three representative soils of China: Lysimeter and batch experiments

Antimony (Sb) distribution, solubility and mobility onto natural soils of China were studied in lysimeter and batch experiments as a function of physicochemical properties of the soil. An outdoor lysimeter experiment investigated the leaching and migration of Sb in the soils with Sb-polluted topsoil and unpolluted subsoil over a 5 month period. Soil solutions were collected by suction cups installed at different depth of lysimeters, and leachates were regularly collected and analyzed for Sb concentrations. The majority of the added Sb was retained in the topsoil layers, but small portions were moved to the sub-layers. Sb concentrations in the soil solutions and leachates ranged from 0–755.5 (6.38 ± 54 on average) μg l⁻¹ and 0–0.45 (smaller than the detection limit) μg l⁻¹ respectively, indicating the low solubility of Sb in the soils. Batch experiments were performed in order to determine the sorption capacity and the partition coefficient (K_d). Freundlich isotherm described properly the equilibrium experimental data and results show that the K_d values for Primosol, Isohumosol, Ferrosol equal to 22.5, 87.8, 704 L kg⁻¹, respectively. These results showed the strong capacity of the soils to retain Sb, and prevent it being leached down the profile. The mobilizable Sb was in the order: Primosol > Isohumosol > Ferrosol. Sb migration in the soils was mainly associated with the exchangeable, carbonate-bound, and metal–organic complex-bound fractions. Health risk assessment indicates that Sb leaching from Ferrosol will not harm to human health through groundwater under the test conditions, while it has certain health risks from the Isohumosol and Primosol.     

Fly and bottom ashes from biomass combustion as cement replacing components in mortars production: Rheological behaviour of the pastes and materials compression strength

In the present research mortar pastes obtained by replacing a commercial cement with the equivalent mass of 5, 10, 20 and 30 wt.% of fly ash or bottom ash from fir chips combustion, were prepared and rheologically characterized. It was observed that the presence of ash modifies their rheological behaviour with respect to the reference blend due to the presence, in the ashes, of KCl and K₂SO₄ which cause precipitation of gypsum and portlandite during the first hydration stages of the pastes. Hydrated materials containing 5 wt.% of ash display compression strength and absorption at 28 d of same magnitude as the reference composition; conversely, progressive increase of ash cause a continuous decline of materials performances. Conversely, samples tested after 180 d display a marked decline of compression strength, as a consequence of potassium elution and consequent alkali-silica reaction against materials under curing.     

Characteristics of oxytetracycline sorption and potential bioavailability in soils with various physical-chemical properties

Veterinary antibiotics are widely used for disease treatment, prevention and animal growth promoting. Frequent detection of veterinary antibiotics in environments, caused by land application of untreated or even treated antibiotics-containing animal wastes, has posed the growing concern of their adverse effect on natural ecosystems. Oxytetracycline (OTC) is one of the most widely-used veterinary antibiotics in livestock industry. OTC present as a cation, zwitterions, or net negatively charged ion in soils complicates predicting its sorption characteristics and potential bioavailability and toxicity. This study was to identify soil properties influencing OTC sorption and its subsequent bioavailability in five soils with various physical-chemical properties. A solution used to determine bioavailable analytes in soils and sediments, 1 M MgCl₂ (pH 8.5), was chosen to desorb the potentially bioavailable fraction of OTC sorbed onto soils. Our results demonstrated that soils with higher illite content and permanent cation exchange capacity have higher OTC sorption capacity, but increase the availability of sorbed OTC indicated by higher release of sorbed OTC from soils into aqueous phase in 1 M MgCl₂ (pH 8.5). Reversely, soil organic matter (SOM), clay, kaolinite, variable cation exchange capacity, DCB-Fe and -Al have lower OTC sorption capacity, but decrease the release of sorbed OTC from soils into 1 M MgCl₂. These findings indicate that SOM and clay greatly influence OTC adsorption and potential availability. This study contributes significantly to our understanding of the potential bioavailability of sorbed OTC and the effects of soil properties on OTC sorption behaviors in soils.     

Screening of heavy metal containing waste types for use as raw material in Arctic clay-based bricks

In the vulnerable Arctic environment, the impact of especially hazardous wastes can have severe consequences and the reduction and safe handling of these waste types are therefore an important issue. In this study, two groups of heavy metal containing particulate waste materials, municipal solid waste incineration (MSWI) fly and bottom ashes and mine tailings (i.e., residues from the mineral resource industry) from Greenland were screened in order to determine their suitability as secondary resources in clay-based brick production. Small clay discs, containing 20 or 40% of the different particulate waste materials, were fired and material properties and heavy metal leaching tests were conducted before and after firing. Remediation techniques (washing in distilled water and electrodialytical treatment) applied to the fly ash reduced leaching before firing. The mine tailings and bottom ash brick discs obtained satisfactory densities (1669–2007 kg/m³) and open porosities (27.9–39.9%). In contrast, the fly ash brick discs had low densities (1313–1578 kg/m³) and high open porosities (42.1–51. %). However, leaching tests on crushed brick discs revealed that heavy metals generally became more available after firing for all the investigated materials and that further optimisation is therefore necessary prior to incorporation in bricks.     

Effect of fly ash on metsulfuron-methyl sorption and leaching in soils

This investigation was undertaken to determine the effect of amendment of two fly ashes [Kota and Inderprastha (IP)] on sorption behavior of metsulfuron-methyl in three Indian soil types. Kota fly ash (5%) did not show any effect on herbicide sorption while IP fly ash significantly enhanced the sorption. Further studies on metsulfuron-methyl sorption-desorption behavior in 0.5, 1, 2, and 5% IP fly ash-amended soils suggested that effect of fly ash varied with soil type and better effect was observed in low organic carbon content soils. The sorption-desorption isotherms fitted very well to the Freundlich sorption equation and, in general, slope (1/n) values less than unity were observed. Metsulfuron-methyl sorption in the IP fly ash-amended soils showed strong correlation with the fly ash content and compared to the Freundlich sorption constant (K _f), K _FA values (sorption normalized to fly ash content) showed less variation. Metsulfuron-methyl leaching studies suggested greater retention of herbicide in the application zone in IP fly ash-amended soils, but effect varied with soil type and no herbicide leaching was observed in 5% fly ash-amended soils. The study suggested that all coal fly ashes are not effective in enhancing the sorption of metsulfuron-methyl in soils. However, one which enhanced herbicide sorption, could play an important role in reducing its leaching losses.     

矿区炼金废渣的固化/稳定化处理

通过对金矿矿区炼金废渣的酸中和能力、净产酸量及浸出毒性实验,测定了废渣的产酸潜力及重金属砷、镉、铅、锌的总量和它们的浸出量。为了合理处置矿区炼金废渣,并为矿区重金属污染土壤的修复提供技术支持,采用石灰、粉煤灰、堆肥化污泥作为添加剂对废渣进行固化/稳定化处理;通过浸出毒性实验对固化/稳定化处理效果进行综合分析,试图寻求一种最佳的稳定剂。结果表明,无论是单独添加石灰、粉煤灰或者堆肥化污泥还是两两组合混合添加,样品浸出液的pH都有升高,As、Cd的浸出浓度都有明显下降,而且两两组合添加比单独添加的固化/稳定化处理效果更好。在两两组合添加中,粉煤灰混合堆肥化污泥的处理效果最好,浸出液的pH值达到7.82,As、Cd的浸出率分别下降72.0%和72.2%。说明粉煤灰混合堆肥化污泥处理炼金废渣效果最佳,同时具有以废治污的资源化生态效能。     

Effect of thermal processing on the characteristics of incineration fly ash

This work investigated the possibilities of immobilizing incineration fly ash by applying different processing methods. Direct sintering of fly ash at 1050 degrees C produced material with increased resistance to leaching; however, the high content of halides prevented the achievement of appropriate strength. Fly ash melting and casting into metallic moulds resulted in the formation of glass with good chemical resistivity and mechanical properties, which were further improved by devitrification, and the formation of glass-ceramics. The most successful combination of strength and resistance to leaching was obtained by a process consisting of fly ash melting, by pouring the melt into water, then grinding, and sintering without additives at 850-950 degrees C. In this way, a material was produced that cannot only be landfilled as a stabilised and non-reactive waste in landfills for non-hazardous wastes, but can also be utilized as a valuable material for manufacturing useful products. This article provided valuable results for policy-makers in Slovenia, about the handling fly ash from incineration plants. Implications: Fly ash from an incineration plant was thermally treated using several processing routes. Ash-melting, by pouring the melt into water and sintering, produced glass-ceramics having an optimal combination of strength and resistance to leaching that can find applications as useful products. These results provide important data for policy makers in Slovenia regarding the building of incineration plants, and handling the solid-waste products, especially fly ash.     

Study of the use of coal fly ash as an additive to minimise fluoride leaching from FGD gypsum for its disposal

The use of coal fly ash as a fluoride retention additive has been studied as a way of treating flue gas desulphurisation (FGD) gypsum for its disposal in landfills. With this end leaching studies following the standard EN-12457-4 [Characterization of waste- Leaching-Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10l/kg for materials with particle size below 10mm (without or with size reduction)] have been performed on FGD gypsum samples treated with different proportions of fly ash (0.1-100%). It was found that the fluoride leachable content in FGD gypsum was reduced in the range 1-55%, depending on the fly ash proportion added to FGD gypsum. High levels of fluoride leaching reduction (close to 40%) were achieved even at relatively low fly ash additions (5%). So, low fly ash incorporations assure the characterization of this by-product as a waste acceptable at landfills for non-hazardous wastes according to the Council Decision 2003/33/EC [Council Decision 2003/33/EC of 19 December 2002 establishing criteria and procedures for the acceptance of waste at landfills pursuant to Article 16 of and Annex II to Directive 1999/31/EC] on waste disposal. Furthermore, the effectiveness of the proposed FGD gypsum stabilization method was also studied in column leaching systems, proving its good performance in simulated conditions of disposal. In such conditions a fluoride leaching reduction value slightly higher than 25% was displayed for a fly ash added amount of 5%.     

Transport modes and pathways of the strongly sorbing pesticides glyphosate and pendimethalin through structured drained soils

Leaching of the strongly sorbing pesticides glyphosate and pendimethalin was evaluated in an 8-month field study focussing on preferential flow and particle-facilitated transport, both of which may enhance the leaching of such pesticides in structured soils. Glyphosate mainly sorbs to mineral sorption sites, while pendimethalin mainly sorbs to organic sorption sites. The two pesticides were applied in equal dosage to a structured, tile-drained soil, and the concentration of the pesticides was then measured in drainage water sampled flow-proportionally.The leaching pattern of glyphosate resembled that of pendimethalin, suggesting that the leaching potential of pesticides sorbed to either the inorganic or organic soil fractions is high in structured soils. Both glyphosate and pendimethalin leached from the root zone, with the average concentration in the drainage water being 3.5 and 2.7 μg L⁻¹, respectively. Particle-facilitated transport (particles >0.24 μm) accounted for only a small proportion of the observed leaching (13-16% for glyphosate and 16-31% for pendimethalin). Drain-connected macropores located above or in the vicinity of the drains facilitated very rapid transport of pesticide to the drains. That the concentration of glyphosate and pendimethalin in the drainage water remained high (>0.1 μg L⁻¹) for up to 7 d after a precipitation event indicates that macropores between the drains connected to underlying fractures were able to transport strongly sorbing pesticides in the dissolved phase. Lateral transport of dissolved pesticide via such discontinuities implies that strongly sorbing pesticides such as glyphosate and pendimethalin could potentially be present in high concentrations (>0.1 μg L⁻¹) in both water originating from the drainage system and the shallow groundwater located at the depth of the drainage system.     

N2O emissions from municipal solid waste landfills with selected infertile cover soils and leachate subsurface irrigation

This study presents the field investigations into the effects of cover soils and leachate subsurface irrigation on N₂O emissions from municipal solid waste landfills. Landfill Site A and Site B, covered with carefully chosen infertile soils, were selected to monitor their diurnal and seasonal variations of N₂O emissions. The annual average N₂O flux was 469 ± 796 μg N₂O-N m⁻² h⁻¹ in Site B with leachate subsurface irrigation, three times that of Site A without leachate irrigation. When an additional soil containing lower contents of carbon and nitrogen was introduced to cover part of Site B, its N₂O fluxes decreased by 1-2 orders of magnitude compared with the left area of Site B. This suggested that carefully selected cover soils could substantially reduce N₂O emissions even under leachate subsurface irrigation. Statistical analysis proved that the availabilities of soil moisture and mineralized nitrogen were the key parameters controlling landfill N₂O emissions.     

Effect of fly ash on sorption behavior of metribuzin in agricultural soils

This investigation was undertaken to determine the effect of two different fly ashes [Kota and Inderprastha (IP)] amendment on the sorption behavior of metribuzin in three Indian soil types. The IP fly ash was very effective in increasing the metribuzin sorption in the soils. The sorption with IP amendment was increased by 15–92%, whereas with the Kota fly ash an increase in sorption by 13–38% was noted. The adsorption isotherms fitted very well to the Freundlich adsorption equation and, in general, slope (1/n) values less then unity were observed. Although both the fly ashes significantly decreased metribuzin desorption, the IP fly ash was comparatively more effective in retaining metribuzin in the soils. Metribuzin sorption in the IP fly ash-amended soils showed strong correlation with the fly ash content and compared to K_f/K_d values, K_FA values (sorption normalized to fly ash content) showed less variation. Metribuzin sorption-desorption did not correlate to the organic carbon content of the soil-fly ash mixture. The study demonstrates that all coal fly ashes may not be effective in enhancing the sorption of metribuzin in soils to the same extent. However, among the fly ashes used in this study, the IP fly ash was observed to be significantly effective in enhancing the sorption of metribuzin in soils. This may play an important role in reducing the run off and leaching losses of the herbicide by retaining it in the soil.     

The extractability and mineralisation of cypermethrin aged in four UK soils

Cypermethrin is a widely used insecticide that has caused concern due to its toxicity in the aquatic environment. As with all land applied pesticides, the most significant source of water pollution is from the soil, either due to leaching or washoff. The behaviour of cypermethrin in the soil controls the likelihood of future pollution incidents, with two of the most significant processes being the formation of bound residues and microbial degradation. The formation of bound residues and mineralisation was measured in four organically managed soils from the UK. The formation of bound residues was measured using three different extraction solutions, 0.01 M CaCl₂, 0.05 M HPCD and acetonitrile. Biodegradation was assessed by measurement of mineralisation of cypermethrin to CO₂. The formation of bound residues varied according to extraction method, soil type and length of ageing. In two of the four soils studied, acetonitrile extractability decreased from 100% initially to 12-14% following 100 d ageing. The extent of mineralisation increased after 10-21 d ageing, reaching 33% of remaining activity in one soil, however following 100 d ageing the extent of mineralisation was significantly reduced in three out of the four soils. As with the formation of bound residues, mineralisation was impacted by soil type and length of ageing.     

Solidification/stabilisation of electric arc furnace waste using low grade MgO

This study aims to evaluate the potential of low grade MgO (LGMgO) for the stabilisation/solidification (S/S) of heavy metals in steel electric arc furnace wastes. Relevant characteristics such as setting time, unconfined compressive strength (UCS) and leaching behaviour assessed by acid neutralisation capacity (ANC), monolithic and granular leaching tests were examined in light of the UK landfill Waste Acceptance Criteria (WAC) for disposal. The results demonstrated that all studied mix designs with Portland cement type 1 (CEM1) and LGMgO, CEM1-LGMgO 1:2 and 1:4 at 40% and 70% waste addition met the WAC requirements by means of UCS, initial and final setting times and consistence. Most of the ANC results met the WAC limits where the threshold pH values without acid additions were stable and between 11.9 and 12.2 at 28 d.Granular leaching results indicate fixation of most of the metals at all mix ratios. An optimum ratio was obtained at CEM1-LGMgO 1:4 at 40% waste additions where none of the metals leaching exceeded the WAC limits and hence may be considered for landfill disposal.The monolithic leaching test results showed that LGMgO performed satisfactorily with respect to S/S of Zn, as the metal component present at the highest concentration level in the waste exhibited very little leaching and passed the leaching test requirement at all mix ratios studied. However, its performance with respect to Pb, Cd and Cr was less effective in reducing their leaching suggesting a higher cumulative rate under those leaching regimes.     

Effects of canopy-deposition interaction on H+ supply to soils in Pinus banksiana and Populus tremuloides ecosystems in the Athabasca oil sands region in Alberta, Canada

Soil acidification has been of concern in the oil sands region in Alberta due to increased acid deposition. Using the canopy budget model, and accounting for H⁺ canopy leaching by organic acids, we determined sources and sinks of H⁺ in throughfall in jack pine (Pinus banksiana) and trembling aspen (Populus tremuloides) stands in two watersheds from 2006 to 2009. In pine stands, H⁺ deposition was greater in throughfall than in bulk precipitation while the opposite was true in aspen stands. The annual H⁺ interception deposition was 148.8-193.8 and 49.7-70.0 mol_c ha⁻¹ in pine and aspen stands, respectively; while the annual H⁺ canopy leaching was 127.1-128.7 and 0.0-6.0 mol_c ha⁻¹, respectively. The greater H⁺ supply in pine stands was caused by greater interception deposition of SO₄²⁻ and organic acids released from the pine canopy. Such findings have significant implications for establishing critical loads for various ecosystems in the oil sands region.     

Solvent extraction for heavy crude oil removal from contaminated soils

A new strategy of heavy crude oil removal from contaminated soils was studied. The hexane-acetone solvent mixture was used to investigate the ability of solvent extraction technique for cleaning up soils under various extraction conditions. The mixtures of hexane and acetone (25 vol%) were demonstrated to be the most effective in removing petroleum hydrocarbons from contaminated soils and approx 90% of saturates, naphthene aromatics, polar aromatics, and 60% of nC₇-asphaltenes were removed. Kinetic experiments demonstrated that the equilibrium was reached in 5 min and the majority of the oil pollutants were removed within 0.5 min. The effect of the ratio between solvent and soil on the extraction efficiency was also studied and results showed that the efficiency would increase following the higher solvent soil ratio. Then the multistage continuous extraction was considered to enhance the removal efficiency of oil pollutants. Three stages crosscurrent and countercurrent solvent extraction with the solvent soil ratio 6:1 removed 97% oil contaminants from soil. Clearly the results showed that the mixed-solvent of hexane and acetone (25 vol%) with character of low-toxic, acceptable cost and high efficiency was promising in solvent extraction to remove heavy oil fractions as well as petroleum hydrocarbons from contaminated soils.     

Hydrometallurgical recovery of zinc from ashes of automobile tire wastes

Study has been performed on the investigation of metal leaching behavior for fly and bottom ashes from automobile tire wastes using acid and alkaline solutions from both viewpoints of environmental protection and resource utilization. The two ashes were found to contain substantial amounts of zinc and iron along with small quantities of cobalt, manganese, magnesium, copper, titanium and aluminum. The fly ash contained a much larger amount of zinc than the bottom ash, and seems to be a promising secondary source for the metal. Effects of such experimental parameters as temperature, time and solid-liquid ratio on the leaching behavior were investigated. Using three mineral acids and citric acid, selective leaching of zinc was successfully attained; the concentration of zinc in the leach liquors from the fly ash reached as high as 20 g l(-1) while the iron leaching was much suppressed. Selective separation of zinc was also attained in the leaching with alkaline solutions, though the percent leaching was lower than that in the acid leaching. Moreover, solvent extraction and precipitation were applied to the metal-loaded leach liquors as downstream processing to evaluate the feasibility of zinc recovery.