Temporal evolution of the main processes that control indoor pollution in an office microenvironment: a case study

The aim of this study is to examine the relative contribution of the outdoor concentration, the ventilation rate, the geometric characteristics of the indoor environment (i.e., extent of indoor surfaces and indoor volume), the deposition, and chemical reactions to the indoor air quality of the office microenvironment. For this case study, the NO, NO₂, and O₃ concentrations indoors and outdoors and TVOCs and CO₂ concentrations indoors were measured in an office microenvironment in Athens, Greece, that was ventilated both naturally and mechanically. The calculated ventilation and loss rates and the measured outdoor concentrations of NO, NO₂, and O₃ were set as input to Multi-chamber Indoor Air Quality Model in order to study the temporal variation of the indoor NO, NO₂, and O₃ concentrations. Results showed that when the ventilation rate and outdoor concentration are high, the relative contribution of the transport process contributes significantly, while the chemical process depends on the contemporary interplay between the indoor O₃, NO, and NO₂ concentrations and lighting levels. The significance of each process was further examined by performing sensitivity tests, and it was found that the most important parameters were the deposition velocities, the UV infiltration rates (which determines the indoor chemical reaction rates), the ventilation rates, and the filtration (when a mechanical ventilation system is used). The effect of the hydrocarbon chemistry was not significant.     

Assessment of indoor and outdoor particulate air pollution at an urban background site in Iran

The relationship between indoor and outdoor particulate air pollution was investigated at an urban background site on the Payambar Azam Campus of Mazandaran University of Medical Sciences in Sari, Northern Iran. The concentration of particulate matter sized with a diameter less than 1 μm (PM_1.0), 2.5 μm (PM_2.5), and 10 μm (PM₁₀) was evaluated at 5 outdoor and 12 indoor locations. Indoor sites included classrooms, corridors, and office sites in four university buildings. Outdoor PM concentrations were characterized at five locations around the university campus. Indoor and outdoor PM measurements (1-min resolution) were conducted in parallel during weekday mornings and afternoons. No difference found between indoor PM₁₀ (50.1 ± 32.1 μg/m³) and outdoor PM₁₀ concentrations (46.5 ± 26.0 μg/m³), indoor PM_2.5 (22.6 ± 17.4 μg/m³) and outdoor PM_2.5 concentration (22.2 ± 15.4 μg/m³), or indoor PM_1.0 (14.5 ± 13.4 μg/m³) and outdoor mean PM_1.0 concentrations (14.2 ± 12.3 μg/m³). Despite these similar concentrations, no correlations were found between outdoor and indoor PM levels. The present findings are not only of importance for the potential health effects of particulate air pollution on people who spend their daytime over a period of several hours in closed and confined spaces located at a university campus but also can inform regulatory about the improvement of indoor air quality, especially in developing countries.     

A systematic indoor air quality audit approach for public buildings

Good indoor air quality (IAQ) in buildings provides a comfortable and healthy environment for the occupants to work, learn, study, etc. Therefore, it is important to ascertain the IAQ status in the buildings. This study is aimed to establish and demonstrate the comprehensive IAQ audit approach for public buildings, based on Portugal national laws. Four public buildings in Portugal are used to demonstrate the IAQ audit application. The systematic approach involves the measurement of physical parameters (temperature, relative humidity, and concentration of the suspended particulate matter), monitoring of the concentrations of selected chemical indicators [carbon dioxide (CO₂), carbon monoxide, formaldehyde, ozone, and total volatile organic compounds], and the measurements of biological indicators (bacteria and fungi). In addition, air exchange rates are measured by the concentration decay method using metabolic CO₂ as the tracer gas. The comprehensive audits indicated some situations of common IAQ problems in buildings, namely: (1) insufficient ventilation rate, (2) too high particle concentration; and (3) poor filtration effectiveness and hygienic conditions in most of the air handling units. Accordingly, a set of recommendations for the improvement of IAQ conditions were advised to the building owner/managers.     

Measurement of atmospheric concentrations of common household pesticides: A pilot study

Air concentrations of 28 of the most commonly used household pesticides were measured inside nine homes in Jacksonville, Florida, and compared with corresponding outdoor levels. The households selected were sorted into three categories according to the degree of pesticide indoor usage. Personal air monitoring was also performed on one resident of each household by means of a portable sampler, which was kept with the person at all times. Five of the pesticides were found in the air inside of the majority of the homes at concentrations as high as 15 gm^–3 (average concentrations, 12 ngm^–3 to 2.4 gm^–3). Indoor levels were generally one to two ordrrs of magnitude higher than surrounding outdoor air levels and personal air measurements were within ± 50% of corresponding indoor values. All samples were collected over 24-hr periods on polyurethane foam and analyzed by capillary colum gas chromatography with mass spectrometric and/or electron capture detection.     

Indoor air pollution by 2-ethyl-1-hexanol in non-domestic buildings in Nagoya, Japan

2-Ethyl-1-hexanol is a possibly causative chemical in sick building symptoms, although 2-ethyl-1-hexanol has received little attention as a hazardous substance in studies on indoor air pollution. Airborne 2-ethyl-1-hexanol concentrations were measured from 2002 to 2004 in 99 rooms of 42 non-domestic buildings in Nagoya, Japan. The diffusive sampling method is effective for the measurement of a low level of 2-ethyl-1-hexanol in indoor air. The geometric mean (geometric standard deviation) of 2-ethyl-1-hexanol concentrations was 16.5 (5.4) microg m(-3) in indoor air and 1.9 (2.2) microg m(-3) in outdoor air. The maximum concentration of 2-ethyl-1-hexanol in indoor air and outdoor air was 2709 microg m(-3) and 12.4 microg m(-3), respectively. Fewer rooms in a small number of new buildings showed high concentrations of 2-ethyl-1-hexanol, while low concentrations were observed in many rooms of these buildings as well as the other new buildings. The room-to-room concentrations of 2-ethyl-1-hexanol in each building exhibited a wide variation. The geometric mean of the 2-ethyl-1-hexanol concentrations was significantly higher for indoor air than for outdoor air (p < 0.01). The correlation of the 2-ethyl-1-hexanol concentrations between indoor and outdoor air was not significant. Mechanical ventilation was effective in the temporary reduction of indoor 2-ethyl-1-hexanol level. These results suggest that the predominant source of 2-ethyl-1-hexanol was indoor areas.     

云南省宣威市和富源县空气和土壤中多环芳烃污染水平研究

宣威市和富源县位于我国云南省东北部,是全世界肺癌发病率最高的地区之一。当地居民在不通风的房间内燃烧烟煤做饭或取暖造成了严重的室内空气污染。研究表明,长期暴露在燃煤造成的污染物中是导致两地居民肺癌持续高发的主要原因,多环芳烃是最可疑的致病因子之一。2008年1月,分别用聚胺脂泡沫和玻璃纤维滤膜采集了当地9个点位室内、室外空气中气相和颗粒物相中的多环芳烃,同时采集了对应点位的土壤样品。通过对样品的分析,考察了当地空气和土壤中多环芳烃的污染水平、特征以及来源。结果证明,当地空气和土壤中存在严重的多环芳烃污染,室内污染显著高于室外,然而随着当地工业的发展室外污染同样不可忽视,主成分分析结合比值法证明,当地室内外多环芳烃的主要污染源来自于煤炭的燃烧。对空气颗粒物和土壤中多环芳烃浓度进行了比较,对土壤中多环芳烃的来源进行了验证。     

某石化化工行业聚集区室内外PM2.5中多环芳烃分布特征及来源

于非采暖季和采暖季分别采集某石化化工行业聚集城市中心城区室内外PM_(2.5)样品,采用高效液相色谱法分析PM_(2.5)上载带的16种PAHs,对其分布特征、来源以及室外PAHs污染对室内污染的贡献进行了初步探讨。结果表明,研究区域非采暖季和采暖季室外PM_(2.5)中ΣPAHs浓度日均值分别为36.3、294 ng/m~3,室内PM_(2.5)中ΣPAHs浓度分别为14.8、84.6 ng/m~3,均以4、5环PAHs为主;室内PAHs主要来自室外渗透污染,但同时明显存在室内排放源贡献;PAHs来源分析进一步证实研究区域PAHs主要来自煤炭、石油等不完全燃烧,采暖季煤炭燃烧源贡献更突出。     

PM1 and PM2.5 ionic composition and VOCs measurements in two typical apartments in Athens, Greece: investigation of smoking contribution to indoor air concentrations

During the last decades, the air quality of the city of Athens has been quite aggravated. Scientific interest has been focused on health effects caused by both outdoor and indoor air pollution. The purpose of this study was the presentation of results from air quality measurements in two similar typical Athenian apartments in the same suburban area. In addition, smoking contribution is investigated, as it is the main factor which differentiates the two apartments. The results showed that it is the outdoor environment that mainly contributes to the air quality of the non-smokers’ house. In the second apartment, PM_2.5, PM₁, and benzene concentrations were found significantly higher due to smoking activity. In contrast, no clear difference in particulate matter ionic composition between the two areas was observed, although in the smoker’s house, ion concentrations were found elevated. This observation amplifies the assumption that in the smoker’s apartment, significant outdoor sources’ contribution cannot be excluded.     

Levels, sources, and health risks of carbonyls in residential indoor air in Hangzhou, China

Concentrations of formaldehyde, acetaldehyde, acetone, propionaldehyde, i-pentanal, and butyraldehyde in residential indoor air in Hangzhou were determined. The mean concentration of the total carbonyl compounds in summer was 222.6 μg/m³, higher than that in winter (68.5 μg/m³). The concentration of a specific carbonyl in indoor air was higher than the outdoor air measurement, indicating the release of carbonyls from the indoor sources. Formaldehyde and acetone were the most abundant carbonyls detected in summer and winter, respectively. Multiple regression analysis indicated that carbonyl concentrations in residential indoor air depended on the age of decoration and furniture, as well as their concentrations in outdoor air. In addition, a primary estimation showed that the health risks of carbonyls in summer were higher than those in winter.     

Measurements of atmospheric aerosol size distributions by co-located optical particle counters

Ambient aerosol number concentrations and size distributions were measured in both indoor and outdoor environments using two identical co-located and concurrently operated optical particle counters (OPCs). Indoor measurements were performed in a research laboratory, whereas two different locations were used for outdoor measurements; the sampling duration exceeded 12 hours and one hour respectively. Results from the two OPCs have been presented for eight size classes between 0.5 and 20 [micro sign]m, represented by central value diameters 0.875, 1.5, 2.75, 4.25, 6.25, 8.75, 12.5 and 15 microm. Overall, for the six indoor and outdoor experiments conducted at different times of day, the mean particle count ratios from the two OPCs for the individual samples showed +/-20% variation for indoor experiments and +/-50% variations for outdoor experiments. Significant random departures of the mean ratios from unity at all size classes were noticed even for indoor sample periods exceeding 20 hours. However, the coefficient of determination (R(2)) for the plots of readings from the two OPCs indicated higher consistency for "fine" particles (0.5-3.5 microm) than for "coarse" particles (10-20 microm), with average R(2) > 0.8 and R(2) < 0.5 respectively. Poisson counting statistics help to explain the divergence in the latter case where number concentrations were very low for the outdoor experiments. However, it cannot explain the divergence for indoor measurements where the concentrations were much higher. Increasing the averaging period reduced the scatter, especially in size classes with low number concentration. However, this procedure may lead to over-smoothing of data for environments with rapidly changing number concentration. These results indicate that, when two such analysers are used for comparative studies, the divergence between their responses may generate significant values of source contribution or deposition flux, even for nominally similar aerosol populations.     

Simultaneous measurement of ventilation using tracer gas techniques and VOC concentrations in homes, garages and vehicles

Air exchange rates and interzonal flows are critical ventilation parameters that affect thermal comfort, air migration, and contaminant exposure in buildings and other environments. This paper presents the development of an updated approach to measure these parameters using perfluorocarbon tracer (PFT) gases, the constant injection rate method, and adsorbent-based sampling of PFT concentrations. The design of miniature PFT sources using hexafluorotoluene and octafluorobenzene tracers, and the development and validation of an analytical GC/MS method for these tracers are described. We show that simultaneous deployment of sources and passive samplers, which is logistically advantageous, will not cause significant errors over multiday measurement periods in building, or over shorter periods in rapidly ventilated spaces like vehicle cabins. Measurement of the tracers over periods of hours to a week may be accomplished using active or passive samplers, and low method detection limits (<0.025 microg m(-3)) and high precisions (<10%) are easily achieved. The method obtains the effective air exchange rate (AER), which is relevant to characterizing long-term exposures, especially when ventilation rates are time-varying. In addition to measuring the PFT tracers, concentrations of other volatile organic compounds (VOCs) are simultaneously determined. Pilot tests in three environments (residence, garage, and vehicle cabin) demonstrate the utility of the method. The 4 day effective AER in the house was 0.20 h(-1), the 4 day AER in the attached garage was 0.80 h(-1), and 16% of the ventilation in the house migrated from the garage. The 5 h AER in a vehicle traveling at 100 km h(-1) under a low-to-medium vent condition was 92 h(-1), and this represents the highest speed test found in the literature. The method is attractive in that it simultaneously determines AERs, interzonal flows, and VOC concentrations over long and representative test periods. These measurements are practical, cost-effective, and helpful in indoor air quality and other investigations.     

Comparison of two dynamic measurement methods of odor and odorant emission rates from freshly dewatered biosolids

Odor and odorant emission rates from freshly dewatered biosolids in a dewatering building of a Water Reclamation Plant (WRP) are measured using the EPA flux chamber and wind tunnel methods. Experimental results are compared statistically to test whether the two methods result in similar emission rates when experiments are performed under field conditions. To the best of our knowledge the literature is void of studies comparing the two methods indoors. In this paper the two methods are compared indoors where the wind velocity and air exchange rate are pertinent field conditions and can be measured. The difference between emission rates of odor and hydrogen sulfide measured with the two methods is not statistically significant (P values: 0.505 for odor, 0.130 for H(2)S). It is concluded that both methods can be used to estimate source emissions but selection of the most effective or efficient method depends on prevailing environmental conditions. The wind tunnel is appropriate for outdoor environments where wind effects on source emissions are more pronounced than indoors. The EPA flux chamber depends on the air exchange rate of the chamber, which simulates corresponding conditions of the indoor environment under investigation and is recommended for estimation of indoor pollution sources.     

Effect of ventilation rate on air cleanliness and energy consumption in operation rooms at rest

The interrelationships between ventilation rate, indoor air quality, and energy consumption in operation rooms at rest are yet to be understood. We investigate the effect of ventilation rate on indoor air quality indices and energy consumption in ORs at rest. The study investigates the air temperature, relative humidity, concentrations of carbon dioxide, particulate matter (PM), and airborne bacteria at different ventilation rates in operation rooms at rest of a medical center. The energy consumption and cost analysis of the heating, ventilating, and air conditioning (HVAC) system in the operation rooms at rest were also evaluated for all ventilation rates. No air-conditioned operation rooms had very highest PM and airborne bacterial concentrations in the operation areas. The bacterial concentration in the operation areas with 6–30 air changes per hour (ACH) was below the suggested level set by the United Kingdom (UK) for an empty operation room. A 70% of reduction in annual energy cost by reducing the ventilation rate from 30 to 6 ACH was found in the operation rooms at rest. Maintenance of operation rooms at ventilation rate of 6 ACH could save considerable amounts of energy and achieve the goal of air cleanliness.     

Assessment of microbiological indoor air quality in an Italian office building equipped with an HVAC system

The purpose of this study was to evaluate the level and composition of bacteria and fungi in the indoor air of an Italian office building equipped with a heating, ventilation and air conditioning (HVAC) system. Airborne bacteria and fungi were collected in three open-space offices during different seasons. The microbial levels in the outdoor air, supply air diffusers, fan coil air flow and air treatment unit humidification water tank were used to evaluate the influence of the HVAC system on indoor air quality (IAQ). A medium–low level of bacterial contamination (50–500 CFU/m³) was found in indoor air. Staphylococcus and Micrococcus were the most commonly found genera, probably due to human presence. A high fungal concentration was measured due to a flood that occurred during the winter. The indoor seasonal distribution of fungal genera was related to the fungal outdoor distribution. Significant seasonal and daily variation in airborne microorganisms was found, underlining a relationship with the frequency of HVAC system switching on/off. The results of this monitoring highlight the role of the HVAC system on IAQ and could be useful to better characterise bacterial and fungal population in the indoor air of office buildings.     

Assessment of natural radiation exposure levels and mass attenuation coefficients of lime and gypsum samples used in Turkey

The activity concentrations of ²²⁶Ra, ²³²Th, and ⁴⁰K in lime and gypsum samples used as building materials in Turkey were measured using gamma spectrometry. The mean activity concentrations of ²²⁶Ra, ²³²Th, and ⁴⁰K were found to be 38 ± 16, 20 ± 9, and 156 ± 54 Bq kg^???1 for lime and found to be 17 ± 6, 13 ± 5, and 429 ± 24 Bq kg^???1 for gypsum, respectively. The radiological hazards due to the natural radioactivity in the samples were inferred from calculations of radium equivalent activities (Ra_eq), indoor absorbed dose rate in the air, the annual effective dose, and gamma and alpha indices. These radiological parameters were evaluated and compared with the internationally recommended limits. The experimental mass attenuation coefficients (μ/ρ) of the samples were determined in the energy range 81–1,332 keV. The experimental mass attenuation coefficients were compared with theoretical values obtained using XCOM. It is found that the calculated values and the experimental results are in good agreement.     

不同气团来源对广州细颗粒物理化特性的影响

利用2006年7月广州细颗粒物质量浓度、数谱分布与化学组成的观测数据与气团后向轨迹聚类分析结果,系统分析了不同气团来源对广州细颗粒物理化特性的影响。观测期间,广州气团来源可分成来自远海、近海、西面陆地和北面陆地4种类型。细颗粒物总数浓度水平在4种类型中基本相当。当气团来自远海时,二次转化影响较小,PM2.5质量浓度较低,颗粒物数浓度从大到小依次为老化爱根核模态新鲜爱根核模态度积聚模态;受到海洋气团的影响,Cl-在PM2.5中比例为4种类型中最大。气团来自近海时,颗粒物二次生成与老化现象突出,数谱峰值出现在积聚模态,而其他类型出现在爱根核模态;SO2-4、OC与NO-3之和在PM2.5中的比例大于50%,为4种类型中最高。气团来自西面陆地和北面陆地时,细颗粒物受陆地传输老化气团和本地来源影响均较明显。来自北面陆地时,250 nm以上颗粒物数浓度明显升高,是PM2.5平均浓度远高于其他类型的直接原因之一。     

Air pollution exposure monitoring and estimation. Part VI. Ambient exposure of adults in an industrialised region

This paper presents methodology and results of a dynamic individual air pollution exposure model (DINEX) that calculates the hourly exposure for each adult in a panel study. Each of over 260 participants, through the use of a diary, provided information used in the model to calculate his/her personal, individualised exposure. The participants filled out the diary daily, hour by hour, over two, two month periods. The exposure assessment model coupled the diary information and results of an indoor/outdoor measurement program, with the results of dispersion modelling on an hourly basis for an industrial area in Norway. The estimated air pollution concentrations from the dispersion model, based on continuous meteorological measurements, were calibrated with air pollutant concentrations measured continuously.     

Benzene Exposure Assessment at Indoor, Outdoor and Personal Levels. The French Contribution to the Life MACBETH Programme

Many VOC represent hazards to human health through chronic exposure. Recent European and world-wide legislation proposes limit values for ambient concentrations of these compounds. However, very little experimental data exists for true population exposure. In 1996, the European MACBETH initiative set out to measure population exposure to benzene in six European cities. This study details the French contribution to this program. Six campaigns were carried out, each comprising measurements at 100 outdoor sites and the participation of 50 non-smoking volunteers who wore personal samplers and had passive monitors installed in their homes. Iso-concentration maps were drawn for each campaign and the results showed that outdoor concentrations were significantly lower than indoors. Almost 75% of the volunteers were exposed to mean concentrations higher than the limit value of 5µgm³. It is demonstrated that personal exposure levels cannot be deduced simply by combining indoor and outdoor background concentrations. It is also shown that there is need for better knowledge of the contributions to overall exposure of outdoor microenvironments and the authors hope that future European directives will take this into account.     

Measurement of particle concentrations in a dental office

Particles in a dental office can be generated by a number of instruments, such as air-turbine handpieces, low-speed handpieces, ultrasonic scalers, bicarbonate polishers, polishing cups, as well as drilling and air sprays inside the oral cavity. This study examined the generation of particles during dental drilling and measured particle size, mass, and trace elements. The air sampling techniques included both continuous and integrated methods. The following particle continuous measurements were taken every minute: (1) size-selective particle number concentration (Climet); (2) total particle number concentration (PTRAK), and; (3) particle mass concentration (DustTrak). Integrated particle samples were collected for about 5 h on each of five sampling days, using a PM_2.5 sampler (ChemComb) for elemental/organic carbon analysis, and a PM₁₀ sampler (Harvard Impactor) for mass and elemental analyses. There was strong evidence that these procedures result in particle concentrations above background. The dental procedures produced number concentrations of relatively small particles (<0.5 μm) that were much higher than concentrations produced for the relatively larger particles (>0.5 μm). Also, these dental procedures caused significant elevation above background of certain trace elements (measured by X-ray fluorescence) but did not cause any elevation of elemental carbon (measured by thermal optical reflectance). Dental drilling procedures aerosolize saliva and products of drilling, producing particles small enough to penetrate deep into the lungs. The potential health impacts of the exposure of dental personnel to such particles need to be evaluated. Increased ventilation and personal breathing protection could be used to minimize harmful effects.