Selective supercritical fluid extraction to estimate the fraction of PCB that is bioavailable to a benthic organism in a naturally contaminated sediment

Selective supercritical fluid extraction (SFE) at 40 degrees C, 120 bar and 60 min was utilised as a means to estimate the bioavailable fraction of PCBs to chironomid larvae in a naturally contaminated limnic sediment. This extraction methodology removed about 50% of the PCBs from the sediment. According to the equilibrium partitioning theory, organisms in that sediment should decrease their uptake from the sediment to the same extent, biota-to-sediment accumulation factors (BSAFs) thus remaining constant. Surprisingly, the BSAFs for 11 PCB congeners decreased some 40% for the selectively extracted sediment as compared to BSAFs for organisms dwelling in untreated sediment. The results were statistically significant at the 0.001 level using a paired t-test. This can only be interpreted so that selective SFE removed easily available PCBs preferentially, leaving more tightly bound PCBs behind. Hence, by fine-tuning extraction conditions, this methodology might be used to estimate bioavailable fractions by chemical means.     

Levels,congener profile and inventory of polychlorinated biphenyls in sediment from the Songhua River in the vicinity of cement plant,China: a case study

This study investigated the contamination levels, homologue, and congener profiles and evaluated the residue inventory of polychlorinated biphenyls (PCBs) in sediment of the Songhua River in the vicinity of cement plant. The total concentration of detected 35 PCB congeners ranged from 1.12 to 2.19 ng/g dry weight (dw) in sediment, with a mean value of 1.56 ng/g dw, and the concentration of PCBs decreased in the following order: the downstream?>?cement plant?>?upstream. The results of total organic carbon (TOC)-normalized PCB concentrations indicate that the sediments have low potential ecological risk in this area. The study results on homologue and congener of PCBs show that the emissions from cement production could be the major sources of PCBs in sediment, and the low-chlorinated PCBs will be exchanged among air, water, and sediment with increasing temperature during summer and flow to downstream with water during the wet season. The spatial density and total burden of PCBs in the surface sediments were 17.2 ng/cm² and 1.2 kg, respectively. To our knowledge, this study is the first to explore the pollution characteristics of unintentionally produced PCB emissions from cement industry by means of monitoring sediment samples.     

Oxygen deficit determinations for a major river in eastern Hong Kong, China

Determination of oxygen deficit in the Hong Kong Shing-Mun River was based on the oxygen uptake by water, algal respiration and river sediment and the oxygen supplied to the river by surface reaeration and algal photosynthesis. A systematic study was conducted to examine the effect of water temperature, flow velocity and water depth on both the oxygen demands and the oxygen supplies. The oxygen budget of a water column in a selected section of the river was modeled. The results of the oxygen budget analysis showed that when water temperature was around 10 degrees C (the lowest temperature in the river), no deficit was observed. When water temperature was 10 degrees C to 20 degrees C, a small oxygen deficit appeared, especially in the deeper water. At the highest water temperature (30 degrees C), the oxygen deficit was maximal, -6.84 g O2/m2/day, in the night-time during the Spring tide period.     

Selective supercritical fluid extraction as a tool for determining the PCB fraction accessible for uptake by chironomid larve in a limnic sediment

Selective supercritical fluid extraction (SFE) at 40 degrees C, 400 bar and 60 min was used to selectively remove bioavailable PCBs from a naturally contaminated limnic sediment. The extraction decreased the sediment concentrations of the nine studied PCBs by 54% (on average). Chironomid larvae were thereafter cultured in pre-extracted sediment as well as in untreated sediment to study the differences in uptake of PCBs in the two cultures. While the prevailing equilibrium partitioning (EqP) theory predicts a 54% decrease in PCB uptake by the chironomids in the pre-extracted sediment, with a maintained biota-to-sediment accumulation factor (BSAF), a decrease in PCB uptake by 91% was observed. For all investigated PCBs the BSAFs were on average 81% lower in the cultures with pre-extracted sediment than in the untreated systems. The data allowed for a calculation of the bioavailable fraction, which was estimated to 60%. This is very close to the 54% removed by selective SFE, demonstrating the possibility of using SFE as a tool to determine the bioavailable PCB fraction in a polluted sediment.     

Diffusion of PAH and PCB from contaminated sediments with and without mineral capping; measurement and modelling

A novel laboratory microcosm test was developed to measure the diffusion of native PAHs and PCBs from sediments in the presence and absence of a capping layer. Diffusive flux of 15 PAHs and 7 PCBs from uncapped sediment from Oslo harbour was 3.8+/-0.9 microg m(-2)d(-1) and 0.010+/-0.003 microg m(-2)d(-1), respectively. The flux from sediments capped with 1cm mineral cap (crushed limestone or crushed gneiss (0-2mm)), observed during the first 410 d, was 3.5-7.3% of the flux from uncapped sediments. By measuring freely dissolved pore water concentrations of 10 PAHs the flux in the microcosm was modelled with steady state and transient diffusion models. The measured flux from uncapped sediment was 27-290% of modelled steady state flux. Good agreement was also found between the measured flux of pyrene from capped sediment and the flux modelled with the transient model when fitting only with the distribution coefficients for pyrene between the cap material and water (Kd_pyr). Fitted Kd_pyr, (210 and 23 l kg(-1) for limestone and gneiss, respectively) was in the same order of magnitude as K(d) calculated from organic carbon content in the cap materials (68 and 14 l kg(-1) respectively). Calculation of the efficiency of a hypothetical cap with 10 cm diffusion path shows that the increased diffusion path length alone can yield a flux reduction >99% through a strong increase in the stagnant diffusive boundary layer from <1 to 100mm.     

Occurrence of PAHs, PCBs and organochlorine pesticides in the Tonghui River of Beijing, China

Tonghui River, a typical river in Beijing, People's Republic of China, was studied for its water and sediment quality, by determining the levels of 16 polycyclic aromatic hydrocarbons (PAHs), 12 polychlorinated biphenyls (PCBs) and 18 organochlorine pesticides in water and sediment samples. Total PAHs, PCBs and organochlorine pesticides concentrations in water varied from 192.5 to 2651 ng/l, 31.58-344.9 ng/l and 134.9-3788 ng/l, respectively. The total PAHs, PCBs and organochlorine pesticides concentrations in surficial sediments were 127-928 ng/g, 0.78-8.47 ng/g and 1.79-13.98 ng/g dry weight, respectively. The results showed that the concentration of these selected organic pollutants in sediment was higher than those in surface water. It may be due to the fact that organic hydrophobic pollutants tend to stay in the sediments. The PAHs were dominated by 2-, 3-ring components in water samples and by 3- and 4-ring compounds in sediment. For organochlorines, alpha-HCH, delta-HCH, Heptachlor, Endosulfan II, DDT are the major organochlorine pesticides in water while Heptachlor, Dieldrin and DDE composed of 95% of total organochlorine pesticides in sediment. For HCHs (HCHs=alpha-HCH+beta-HCH+gamma-HCH+delta-HCH), the predominance of alpha-HCH of total HCHs were clearly observed in water and sediment. PCB18, PCB31 and PCB52 were predominant in water, on average these compounds collectively accounted for 67% of total PCBs. But in sediment, the predominant compounds were PCB28, PCB31 and PCB153, which accounted for 71% of total PCBs in sediment. The levels of micro pollutants in our study areas were compared with other studies.     

Seasonal air-water exchange fluxes of polychlorinated biphenyls in the Hudson River Estuary

Polychlorinated biphenyls (PCBs) were measured in the air and water over the Hudson River Estuary during six intensive field campaigns from December 1999 to April 2001. Over-water gas-phase SigmaPCB concentrations averaged 1100 pg/m3 and varied with temperature. Dissolved-phase SigmaPCB concentrations averaged 1100 pg/L and displayed no seasonal trend. Uncertainty analysis of the results suggests that PCBs with 5 or fewer chlorines exhibited net volatilization. The direction of net air/water exchange could not be determined for PCBs with 6 or more chlorines. Instantaneous net fluxes of SigmaPCBs ranged from +0.2 to +630 ng m(-2) d(-1). Annual fluxes of SigmaPCBs were predicted from modeled gas-phase concentrations, measured dissolved-phase concentrations, daily surface water temperatures and wind speeds. The net volatilization flux was +62 microg m(-2) yr(-1), corresponding to an annual loss of +28 kg/yr of SigmaPCBs from the Hudson River Estuary for the year of 2000.     

Removal of PCBs from wastewater using fly ash

Liquids and sludges containing polychlorinated biphenyls (PCBs) can be treated to concentrate the PCBs in a solid residue. The latter can then be handled to destroy the PCBs. A study on sorption kinetics of PCBs on fly ash was conducted in controlled batch systems. TCB and HeCB are removed at 25 degrees C by adsorption on fly ash up to 97% at pH 7, with an adsorbent dose of 5 g/l. An examination of the thermodynamic parameters shows that the adsorption of TCB and HeCB by fly ash is a process occurring spontaneously at ambient conditions. Activation energies for the sorption process ranged between 5.6 and 49.1 kJ/mol. It was observed that the rate at which TCB and HeCB are adsorbed onto fly ash showed a diffusion limitation. The uptake rate of TCB and HeCB increases with increasing initial concentration and gradually tends to a constant value. A decrease in the adsorption of TCB and HeCB was observed when interfering ions and other PCB congeners were present. Changing the pH in the aqueous solution from 2 to 10 had no effect on the adsorption process. Overall, fly ash can be used for an efficient removal of PCBs from several aqueous solutions.     

Persistent organic pollutants in atmospheric deposition and biomonitoring with Tillandsia usneoides (L.) in an industrialized area in Rio de Janeiro state, southeast Brazil--Part II: PCB and PAH

Monitoring of immission of persistent organic pollutants in the industrialized area of Volta Redonda (V.R.) and in the National Park of Itatiaia (PNI) in southeast Brazil was performed using an endemic bromeliad species as biomonitor and measuring bulk deposition rates of polychlorinated biphenyls (PCB) and polycyclic aromatic hydrocarbons (PAH). For the sum of PCB, overall deposition rates were between 17 and 314 ng/(m2 day) in winter and between 43 and 81 ng/(m2 day) in summer, respectively. Deposition rates of dioxin-like PCBs ranged from 0.14 to 2.8 pg WHO-TEQ/(m2 day) in winter and from 0.90 to 4.3 pg WHO-TEQ/(m2 day) in summer. PCB deposition rates (total PCB and WHO-TEQ) were in the same range in winter in V.R. and PNI. In summer, contamination levels in V.R. were 6-10-folds higher than in PNI. PCB concentrations in biomonitor samples from V.R. and PNI were in the same range in summer and in winter. Concentrations of total PCB ranged from 14 to 95 microg/kg dry matter (d.m.) in winter and from 18 to 27 microg/kg d.m. in summer, respectively. The TEQ values were between 1.7 and 4.1 ng WHO-TEQ/kg d.m. in winter and between 1.9 and 2.9 ng WHO-TEQ/kg d.m. in summer. PCB concentrations of di-ortho PCB but not of non-ortho PCB were a factor of 2-4 lower in summer in both areas. PCB congener profiles resembled those from technical formulations. The profiles shifted to the higher chlorinated congeners in summer, probable due to revolatilisation of the lighter components at higher temperatures. PCB profiles in biomonitor resembled those from deposition samples and the shift to the heavier congeners in summer was even more pronounced. PAH deposition rates were in a similar range in both areas (131-2415 ng/(m2 day)). PAH levels in biomonitor samples from V.R. were about one order of magnitude higher than in samples from PNI indicating the impact of local sources. PAH profiles revealed stationary thermal processes as main source of contamination in V.R. whereas in PNI, biomass burning seems to be the main contamination source.     

Environmental contamination with polychlorinated biphenyls in the area of their former manufacture in Slovakia

Evidently increased environmental pollution as a consequence of the 25-year manufacture of polychlorinated biphenyls (PCBs) in eastern Slovakia was observed. PCB levels determined in ambient air, soil, surface water, bottom sediment, wildlife (fish and game) samples collected in a potentially contaminated area of about 250 km2 (a part of the Michalovce district) were compared with those determined in a control area (Stropkov district). Up to 1700 ng/m3 were found in ambient air in a village close to a manufacturer's dumping site and a highly contaminated manufacturer's effluent canal whereas PCB concentrations in ambient air samples taken in villages in the control area were about 80 ng/m3 only. While soil samples taken from the agricultural fields of the polluted area contained PCBs at levels comparable with soil samples from the control area (about 0.008 mg/kg) much higher values (from 0.4 to 53,000 mg/kg) were determined in soil taken in the vicinity of manufacturer's landfill and storage sites and especially plants preparing asphalted gravel using formerly PCBs in their heat-exchanging systems. The contamination of the Laborec river and large Zemplinska Sirava reservoir is caused by the manufacturer's effluent canal since PCB levels in the canal sediment are still to be found about 3000 mg/kg. While PCB levels in sediment samples from Michalovce watercourses ranged between 1.7 and 6 mg/kg, sediment samples from the control Stropkov district ranged between 0.007 and 0.052 mg/kg only. Fish living in contaminated Michalovce waters contained about hundred times higher PCB levels than those caught in Stropkov ones. Similarly, game animals shot in Michalovce forests contained several times higher levels than those shot in Stropkov ones.     

Further studies on the uptake of persistent organic pollutants (POPs) by polyurethane foam disk passive air samplers

Passive air samplers (PAS) can be used to monitor semi-volatile organic compounds in the atmosphere. Polyurethane foam (PUF) disks are a popular sampling medium because they have a high retention capacity for such compounds. This paper reports a highly time-resolved uptake study, to derive uptake rate data under field conditions, and investigate the effects of using different foam densities on the uptake rate. PUF disks were deployed alongside an active sampler, for periods of up to 12 weeks. The uptake rates were measured for a range of gas- and particle-bound persistent organic pollutants (polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs)), of different properties, to explore whether gas–particle partitioning affected uptake rate. Uptake rates for two different densities of foam (0.021 and 0.035 g cm^?3) were not statistically significantly different from each other. Uptake rates of light PCBs averaged ～6.5 m³ day^?1, somewhat higher than in previous studies; higher wind speeds and lower temperatures in this study are the likely reason for this difference. The study showed: i) the uptake rate of the compound with lowest K_OA considered in this study (PCB-28/31) declined in the later weeks, indicating an approach to equilibrium; ii) uptake rates of lighter BDEs and heavier PCBs (compounds of intermediate K_OA in this study) remain similar throughout the study period, indicating that they are not approaching equilibrium during the 12-week-study; iii) uptake rates were typically: ～8 m³ day^?1 for PCB-52; ～9.5 m³ day^?1 for PCB-95; ～11 m³ day^?1 for BDE-28 and ～2 m³ day^?1 BDE-99. The latter compound has an important particle-bound component and this lowers the sampling rate compared to predicted uptake rates for compounds which are in the gas phase only. It is shown that knowledge of gas–particle partitioning is needed to correct for this effect, and to improve predicted uptake rates.     

PCDD/F and PCB history in dated sediments of a rural lake

Concentrations of polychlorinated dibenzo-p-dioxins (PCDD), dibenzofurans (PCDF) and biphenyls (PCB) were analysed from a sediment core, which had been sampled from a remote lake in Finland. The deepest subsamples were analysed from a depth of 4.0 m, and were more than 8000 years old. At the surface of the sediment core, low levels of industrial background contamination were detected. The sum of 2,3,7,8-substituted PCDD/Fs was 35 ng/kg d.w. (dry weight), or 1.2 ng/kg d.w. in WHO's toxicity equivalent, WHO-TEQ. The annual accumulation rate of 2,3,7,8-substituted PCDD/Fs was 1.26 ng m(-2) a(-1). Deeper in the core, PCDD/F concentrations ranged between 2.11 and 11.1 ng/kg d.w. (0.24 and 1.70 ng/kg d.w. WHO-TEQ) and the accumulation rate was 0.11 ng m(-2) a(-1). A characteristic PCDD/F congener profile was found in all pre-industrial sediment layers. The order of concentrations was OCDD > 1,2,3,4,6,7,8-HpCDD > 1,2,3,7,8,9-HxCDD > 1,2,3,4,7,8-HxCDD > 2,3,7,8-TCDD, and concentrations of 2,3,7,8-chlorinated dibenzofurans were below the detection limit. Similar congener profiles have previously been described in samples for which natural PCDD/F formation has been proposed. PCBs were present at low levels in all of the sediment samples. The sum of the PCB concentrations of the sediment subsamples ranged between 50 and 2540 ng/kg d.w., and the three predominant congeners in the core were PCBs 18, 52, and 110.     

Polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) distributions in the Bay of Marmara sea: Izmit Bay

In 1999, the concentrations of 16 polycyclic aromatic hydrocarbons (PAHs), the total PAH and polychlorinated biphenyls (PCBs) were measured in sea water, sediment and mussels collected along the coast of Izmit Bay, the most important bay of the Marmara Sea. The total-PAH concentrations, measured by Spectrofluorometry were in the range of 1.16-13.68 microg/l in sea water, in the range of 30.0 1670.0 microg/g dry weight in sediments and in the range from 5.67 to 14.81 microg/g wet weight in edible part of mussel. HPLC revealed Phenanthrene (three rings), chrysene (four rings) and benz[a]antracene (five rings) to be the dominant PAHs in sea water, while 16 different PAHs compounds were observed and measured in mussel samples. The most pollution occured at Dogu Kanali and Dil Deresi where were the main rivers containing wastes fall into the the Izmit Bay. Although the maximum mono-ortho PCB concentrations in sea water were measured in the Dil Deresi River (26.33 ng/l) and the Solventa? (22.19 ng/l) stations, maximum PCB concentrations in mussels were measured in the SEKA (28.11 microg/kg) and the Dil Deresi River (25.68 microg/kg). The dominant congeners of PCBs were from tetra to hexachlorobiphenyls. The toxicity equivalent values were very low in sea water and mussels.     

Denitrification in cypress swamp within the Atchafalaya River Basin, Louisiana

Nitrogen has been implicated as a major cause of hypoxia in shallow water along the Louisiana/Texas, USA coasts. Excess nitrogen (mainly nitrate) from Mississippi and Atchafalaya River drainage basins may drive the onset and duration of hypoxia in the northern Gulf of Mexico. Restoring and enhancing denitrification have been proposed to reduce and control coastal hypoxia and improve water quality in the Mississippi River Basin. Sediments were collected from six baldcypress restoration sites within the Atchafalaya River Basin, Louisiana, USA. The acetylene blockage technique was used to measure background and potential sediment denitrification rates. Denitrification fluxes were measured before nitrate addition (background rates) and after nitrate addition of 100mgNl(-1) (potential denitrification) at three seasonal temperatures. Background denitrification was low across all cypress swamp sites ranging from 0.9 to 8.8, 0.6 to 28.5 and 8.8 to 47.5g N evolved ha(-1)d(-1) at water/sediment column temperatures of 8, 22 and 30 degrees C, respectively. After nitrate addition, temperature had a significant effect on sediment denitrification potential. Maximum rates measured at 8, 22 and 30 degrees C were approximately 250-260, 550 and 970gNha(-1)d(-1), respectively. Most of the added nitrate in water columns, incubated at 8 degrees C, was removed after 65d compared to 32d and 17d at 22 and 30 degrees C, respectively. These results indicate cypress swamps have the potential to assimilate and process elevated levels of floodwater nitrate with denitrification being a major removal mechanism.     

Measures to prevent emissions of PCDDS/DFs and co-planar PCBs from crematories in Japan

In this study, PCDDs/DFs and co-planar PCBs concentrations in flue gases from 17 crematories and in fly ashes and bottom ashes (mainly bone) from several crematories were measured to grasp the present state of PCDDs/DFs emissions from crematories. The effects of several factors were discussed to prevent PCDDs/DFs emissions from crematories. Total concentration (normalized by 12% O2) of PCDDs/DFs was ranged from 4.9 to 1200 ng/m3 N, and toxic equivalent concentration was ranged from 0.064 to 24 ng TEQ/m3 N. As the results obtained in this research, the following measures to reduce PCDDs/DFs emission are recommended for existing crematories: (1) keeping the temperature at 800 degrees C in main/secondary chambers during a whole cremation, and (2) lowering the temperature in the dust collector. For newly installed crematories, following measures to prevent PCDDs/DFs emission including the measures for existing ones are recommended: (1) connecting one secondary chamber to one main chamber, (2) installing the high efficiency dust collector and reducing dust concentration to less than 0.01 g/m3 N, and (3) installing the sampling point for monitoring of PCDDs/DFs.     

Uptake of PAHs into polyoxymethylene and application to oil-soot (lampblack)-impacted soil samples

Polyoxymethylene (POM) is a polymeric material used increasingly in passive sampling of hydrophobic organic contaminants such as PAHs and PCBs in soils and sediments. In this study, we examined the sorption behavior of 12 PAH compounds to POM and observed linear isotherms spanning two orders of magnitude of aqueous concentrations. Uptake kinetic studies performed in batch systems for up to 54 d with two different volume ratios of POM-to-aqueous phase were evaluated with coupled diffusion and mass transfer models to simulate the movement of PAHs during the uptake process and to assess the physicochemical properties and experimental conditions that control uptake rates. Diffusion coefficients of PAHs in POM were estimated to be well correlated with diffusants' molecular weights as D(POM) proportional, variant(MW)(-3), descending from 2.3 x 10(-10) cm(2) s(-1) for naphthalene to 7.0 x 10(-11) cm(2) s(-1) for pyrene. The uptake rates for PAHs with log K(ow)<5.8 were controlled by the POM phase and the hydrophobicity of PAH compounds. For more hydrophobic PAH compounds, the aqueous boundary layer played an increasingly important role in determining the overall mass transfer rate. The POM partitioning technique was demonstrated to agree well with two other procedures for measuring PAH soil-water distribution coefficients in oil-soot (lampblack) containing soil samples.     

Combined steam distillation and electrochemical peroxidation (ECP) treatment of river sediment contaminated by PCBs

A combined treatment process utilizing steam distillation followed by electrochemical peroxidation (ECP) has been utilized to remove >90% of the polychlorinated biphenyls (PCBs) in St. Lawrence River sediment and destroy 95% of the PCBs recovered in the condensate. 2 l of condensate were collected by boiling 500 grams of sediment containing 4.3 mg PCBs. Most of the PCBs (82.3%) were recovered as a small volume (<1 ml) of yellow oil floating on the condensate and coating glassware surfaces. The aqueous phase PCBs (182 μg/l) were destroyed (95%) by three sequential ECP treatments at 16.8°C and pH 5, utilizing 1 ml of H₂O₂ (3%) and periodically reversed current (0.75–1.0 A @ 10 volts). Oxidation is primarily mediated by hydroxyl radicals produced by the reaction of hydrogen peroxide with electrochemically generated ferrous iron (Fenton's reagent). This work suggests steam extraction, in combination with advanced oxidation technologies, provides an effective treatment strategy for contaminated solids.     

Assessment of bioavailable PAH, PCB and OCP concentrations in water, using semipermeable membrane devices (SPMDs), sediments and caged carp

Bioavailable water concentrations of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) were assessed at several freshwater sites in and around the city of Amsterdam. Carp (Cyprinus carpio) were caged for 4 weeks at 10 sites, together with semipermeable membrane devices (SPMDs). In addition, sediment samples were taken at each site. SPMDs and sediments were analysed for PAHs, PCBs and OCPs. Carp muscle tissues were analysed for PCBs and OCP, while PAH metabolites were assessed in fish bile. Contaminant concentrations in the water phase were estimated using three different methods: 1. Using fish tissue concentrations and literature bioconcentration factors (BCFs), 2. Using SPMD levels and a kinetic SPMD uptake model, and 3. Using sediment levels and literature sorption coefficients (K_ocs). Since PAH accumulation in fish is not considered an accurate indicator of PAH exposure, calculated aqueous PAH concentrations from SPMD data were compared with semiquantitatively determined biliary PAH metabolite levels. Contaminant concentrations in the water phase estimated with fish data (Cw_fish) and SPMD data (Cw_spmd) were more in line for compounds with lower K_ow than for compounds with higher K_ow values. This indicates that the assumption of fish–water sorption equilibrium was not valid. At most sites, sediment-based water levels (Cw_sed) were comparable with the Cw_spmd, although large differences were observed at certain sites. A significant correlation was observed between biliary PAH metabolite levels in fish and aqueous PAH concentrations estimated with SPMD data, suggesting that both methods may be accurate indicators of PAH exposure in aquatic ecosystems.     

Uptake and elimination of perchlorate in eastern mosquitofish

The purpose of this study was to investigate the uptake and elimination of perchlorate in eastern mosquitofish (Gambusia holbrooki). Fish were exposed to 0.1-1000 mg/l sodium perchlorate for 12h, 1, 2, 5, 10, and 30 days, and perchlorate was determined in whole body extracts. Perchlorate was not detected in mosquitofish exposed to the low concentrations of perchlorate (0, 0.1, and 1mg/l sodium perchlorate), regardless of the exposure time, whereas it was detected when fish were exposed to 10, 100, and 1000 mg/l. The tissue concentrations were approximately 10 times less than that in the water. There was no difference in the uptake of perchlorate depending upon the exposure time, however, a difference in perchlorate uptake depending upon the concentration of the exposure dose (P<0.001) was observed. Uptake (K(u)) and elimination (K(e)) rate constants were 0.09 l/mg day and 0.70 day(-1), respectively. The half-life (T1/2) of perchlorate was 0.99 day. Thus, it appears that perchlorate is rapidly taken up and eliminated in eastern mosquitofish. These results are critical and may be used to develop models of fate, effects, and transport of perchlorate in natural systems, as well as to assess ecological risk in affected ecosystems.     

Influence of trophic status on PCB distribution in lake sediments and biota

We investigated the relationship between trophic status and polychlorinated biphenyl (PCB) distribution in 19 Swedish lakes. We analyzed PCB in water, phytoplankton, zooplankton, fish and sediment during two sampling periods, in spring and summer. The mass of sigma PCB in the lake sediments was positively related to lake trophy, i.e. more PCBs were accumulated and buried in the sediment of eutrophic lakes than in oligotrophic lakes. In the oligotrophic lakes a greater fraction of the total PCB load was dissolved in water. We conclude that this is a result of higher sedimentation rates in eutrophic lakes and relatively lower turnover of organic carbon in the water column of the shallow, eutrophic lakes. In the stratified lakes, the amount of PCB per cubic meter in the epilimnion decreased from spring to summer. We suggest that sedimentation of plankton beneath the thermocline during stratification act as a sink process of PCBs from the epilimnion.