The formation of dithionate during the iron(III)-catalysed autoxidation of sulfur(IV)-oxides

The iron(III)-catalyzed autoxidation of sulfur(IV)-oxides results in the formation of two different oxidation products of sulfur(IV): dithionate, S₂O₆²⁻, and sulfate, SO₄²⁻. The yield of these reaction products depends on the experimental conditions. Under the studied conditions ([Fe(III)] : [SIV)] = 1:10, pH = 2–4) dithionate is the minor reaction product. The formation of dithionate is influenced by the initial pH but not by the initial O₂ concentration. The presence of CO²⁺, Mn²⁺, and Ni²⁺ have no influence on the yield of dithionate, whereas in the presence of Cr³⁺ less and, in the presence of Cu²⁺, no dithionate is formed.     

Iron-catalyzed oxidation of s(IV) species by oxygen in aqueous solution: Influence of pH on the redox cycling of iron

Redox cycling of Fe(II)/Fe(III) during the catalyzed aqueous S(IV) oxidation by dissolved oxygen in the presence of Fe(II) and/or Fe(III) at an initial pH_i of 4.4, often observed in atmospheric waters, was studied in detail. It has been found that the reaction rate is not considerably affected by the oxidation state of iron at the start of the reaction. An equilibrium between Fe(II) and Fe(III) was established a few minutes after the start of the reaction, regardless of the oxidation state of iron at the beginning of the experiment. The prevailing oxidation state of iron in a particular phase of the reaction depends on the concentration of S(IV) in the reaction solution. It has been found that the formation of polymerized hydroxo Fe(III) species is also included in the mechanism of the Fe-catalyzed oxidation of S(IV). The formation of these species was confirmed by the on-line measurement of Fe(II) and Fe_reac. The results also clearly demonstrate that the pH_i of the solution is a major factor, controlling the concentration of Fe(III) ions, the form of S(IV) species, and consequently the reaction rate of S(IV) oxidation by oxygen.     

粗MnSO4溶液中MnS2O6的去除条件研究

用软锰矿吸收SO2生成MnSO4时会伴随有副产物MnS2O6生成。产品中MnS2O6的存在会降低硫酸锰产品质量,同时会缓慢释放出SO2气体污染环境。本文用单因素实验方法研究了粗MnSO4溶液中MnS2O6的最优去除条件。研究结果显示,软锰矿用量为12.2 g,硫酸加入量为20 mL、反应温度100℃、反应时间3 h、搅拌速度500 r/min,MnS2O6的去除率可达91%以上。其最终产品能达到GB1622-1986一级品标准。     

Influence of NO2 and dissolved iron on the S(IV) oxidation in synthetic aqueous solution

The influence of dissolved NO₂ and iron on the oxidation rate of S(IV) species in the presence of dissolved oxygen is presented. To match the conditions in the real environment, the concentration of iron in the reaction solution and trace gases in the gas mixture was typical for a polluted atmosphere. The time dependence of HSO₃⁻, SO₄²⁻, NO₂⁻ and NO₃⁻ and the concentration ratio between Fe(II) and total dissolved iron were monitored. Sulphate formation was the most intensive in the presence of an SO₂/NO₂/air gas mixture and Fe(III) in solution. The highest contribution to the overall oxidation was from Fe-catalysed S(IV) autoxidation. The reaction rate in the presence of both components was equal to the sum of the reaction rates when NO₂ and Fe(III) were present separately, indicating that under selected experimental conditions there exist two systems: SO₂/NO₂/air and SO₂/NO₂/air/Fe(III), which are unlikely to interact with each other. The radical chain mechanism can be initiated via reactions Fe(III)–HSO₃⁻ and NO₂–SO₃²⁻/HSO₃⁻.     

A comparative study of the effects of chloride, sulfate and nitrate ions on the rates of decomposition of H2O2 and organic compounds by Fe(II)/H2O2 and Fe(III)/H2O2

The effects of chloride, nitrate, perchlorate and sulfate ions on the rates of the decomposition of hydrogen peroxide and the oxidation of organic compounds by the Fenton's process have been investigated. Experiments were conducted in a batch reactor, in the dark at pH < or = 3.0 and at 25 degrees C. Data obtained from Fe(II)/H2O2 experiments with [Fe(II)]0/[H2O2]0 > or = 2 mol mol(-1), showed that the rates of reaction between Fe(II) and H2O2 followed the order SO4(2-) > ClO4(-) = NO3- = Cl-. For the Fe(III)/H2O2 process, identical rates were obtained in the presence of nitrate and perchlorate, whereas the presence of sulfate or chloride markedly decreased the rates of decomposition of H2O2 by Fe(III) and the rates of oxidation of atrazine ([atrazine]0 = 0.83 microM), 4-nitrophenol ([4-NP]0 = 1 mM) and acetic acid ([acetic acid]0 = 2 mM). These inhibitory effects have been attributed to a decrease of the rate of generation of hydroxyl radicals resulting from the formation of Fe(III) complexes and the formation of less reactive (SO4(*-)) or much less reactive (Cl2(*-)) inorganic radicals.     

The iron catalyzed oxidation of sulfur: Reconciliation of the literature rates

We have measured three inhibiting effects in the iron(III) catalyzed oxidation of sulfur(IV) to sulfur(VI) in aqueous solution. The reaction is inhibited by ionic strength, sulfate ion, and it is self-inhibited. Consideration of these three effects makes it possible to reconcile several apparently disparate studies of this reaction in the literature. The implication for atmospheric chemistry is that this reaction may be more important in cloudwater than previously believed.     

Kinetics and stoichiometry of aerobic sulfide oxidation in wastewater from sewers-effects of pH and temperature.

Kinetics and stoichiometry of aerobic chemical and biological sulfide oxidation in wastewater from sewer networks were studied. In this respect, the effects of temperature and pH were investigated in the ranges 10 to 20 degrees C and 5 to 9, respectively. The temperature dependency of sulfide oxidation kinetics was described using an Arrhenius relationship. The effect of pH on the rate of chemical sulfide oxidation is related to the dissociation of hydrogen sulfide (H2S) to hydrogen sulfide ion (HS(-)), with HS(-) being more readily oxidized than H2S. Biological sulfide oxidation exhibited the highest rates at ambient wastewater pH, and the reaction was inhibited at both low and high pH values. Chemical sulfide oxidation was found to produce thiosulfate and sulfate, while elemental sulfur was the main product of biological sulfide oxidation. Based on the investigations, general rate equations and stoichiometric constants were determined, enabling the processes to be incorporated to conceptual sewer process models.     

粗MnSO4溶液中MnS2O6的去除条件研究

用软锰矿吸收SO₂生成MnSO₄时会伴随有副产物MnS₂O₆生成。产品中MnS₂O₆的存在会降低硫酸锰产品质量,同时会缓慢释放出SO₂气体污染环境。本文用单因素实验方法研究了粗MnSO₄溶液中MnS₂O₆的最优去除条件。研究结果显示,软锰矿用量为12.2 g,硫酸加入量为20 mL、反应温度100℃、反应时间3 h、搅拌速度500 r/min,MnS₂O₆的去除率可达91%以上。其最终产品能达到GB1622-1986一级品标准。     

Influence of ozone, relative humidity, and flow rate on the deposition and oxidation of sulfur dioxide on yellow sand

To evaluate the influences of O₃, relative humidity (RH), and flow rate on the reaction between yellow sand and SO₂, the SO₂ deposition velocity and the oxidation state of sulfur were investigated by means of exposure experiments in a cylindrical flow reactor. Early in the reaction, the deposition velocity was not influenced by the RH or the presence of O₃; as the reaction progressed, however, the deposition velocity increased in the presence of O₃ and at high humidity. The oxidation of sulfur from S(IV) to S(VI) was also enhanced under these conditions. The amount of sulfur oxidation was positively correlated with the amount of deposited O₃. Furthermore, the SO₂ deposition velocity increased with increasing flow rate. However, changes in the flow rate had no noticeable effect on the amount of SO₂ oxidation.     

Kinetics and mechanism of oxidation of tetrachloroethylene with permanganate

The kinetics, reaction pathways and product distribution of oxidation of tetrachloroethylene (PCE) by potassium permanganate (KMnO4) were studied in phosphate-buffered solutions under constant pH, isothermal, completely mixed and zero headspace conditions. Experimental results indicate that the reaction is first-order with respect to both PCE and KMnO4 and has an activation energy of 9.3+/-0.9 kcal/mol. The second-order rate constant at 20 degrees C is 0.035+/-0.004 M(-1) s(-1), and is independent of pH and ionic strength (I) over a range of pH 3-10 and I approximately 0-0.2 M, respectively. The PCE-KMnO4 reaction may proceed through further oxidation and/or hydrolysis reaction pathways, greatly influenced by the acidity of the solution, to yield CO2(g), oxalic acid, formic acid and glycolic acid. Under acidic conditions (e.g., pH 3), the further oxidation pathway will dominate and PCE tends to be directly mineralized into CO2 and chloride. Under neutral (e.g., pH 7) and alkaline conditions (e.g., pH 10), the hydroxylation pathway dominates the reaction and PCE is primarily transformed into oxalic acid prior to complete PCE mineralization. Moreover, all chlorine atoms in PCE are rapidly liberated during the reaction and the rate of chloride production is very close to the rate of PCE degradation.     

TiO2-catalyzed photooxidation of arsenite to arsenate in aqueous samples

The TiO2-catalyzed photooxidation of arsenite (As(III)) to arsenate (As(V)) was studied in aqueous TiO2 suspensions using a solar simulator which emitted ultraviolet and visible radiations. The concentration of As(III) was varied between 50 microg l(-1) and 10 mg l(-1), and the concentration of TiO2 between 1 mg l(-1) and 50 mg l(-1). Total oxidation of As(III) to As(V) occurred within minutes. The concentration of As(III) declined exponentially which indicates first-order kinetics. In the pH range between 5 and 9 there was no significant influence of the pH of the suspension on the reaction rate. Batch experiments without irradiation showed that part of the arsenic was adsorbed on the TiO2 surface. When using 100 microg l(-1) As and between 1 mg l(-1) and 50 mg l(-1) TiO2, 8-39% of As(III) and up to 73% of As(V) were adsorbed by TiO2. As(III) was also oxidized by UV radiation in the absence of TiO2, but the reaction was slower than in the presence of TiO2 resulting in an irradiation time too long for practical use. In addition, oxidation of As(III) in the presence of TiO2 was also observed under solar irradiation within a few minutes.     

Ferric iron amendment increases Fe(III)-reducing microbial diversity and carbon oxidation in on-site wastewater systems

Onsite wastewater systems, or septic tanks, serve approximately 25% of the United States population; they are therefore a critical component of the total carbon balance for natural water bodies. Septic tanks operate under strictly anaerobic conditions, and fermentation is the dominant process driving carbon transformation. Nitrate, Fe(III), and sulfate reduction may be operating to a limited extent in any given septic tank. Electron acceptor amendments will increase carbon oxidation, but nitrate is toxic and sulfate generates corrosive sulfides, which may damage septic system infrastructure. Fe(III) reducing microorganisms transform all major classes of organic carbon that are dominant in septic wastewater: low molecular weight organic acids, carbohydrate monomers and polymers, and lipids. Fe(III) is not toxic, and the reduction product Fe(II) is minimally disruptive if the starting Fe(III) is added at 50–150 mg L^?1. We used ¹⁴C radiolabeled acetate, lactate, propionate, butyrate, glucose, starch, and oleic acid to demonstrate that short and long-term carbon oxidation is increased when different forms of Fe(III) are amended to septic wastewater. The rates of carbon mineralization to ¹⁴CO₂ increased 2–5 times (relative to unamended systems) in the presence of Fe(III). The extent of mineralization reached 90% for some carbon compounds when Fe(III) was present, compared to levels of 50–60% in the absence of Fe(III). ¹⁴CH₄ was not generated when Fe(III) was added, demonstrating that this strategy can limit methane emissions from septic systems. Amplified 16S rDNA restriction analysis indicated that unique Fe(III)-reducing microbial communities increased significantly in Fe(III)-amended incubations, with Fe(III)-reducers becoming the dominant microbial community in several incubations. The form of Fe(III) added had a significant impact on the rate and extent of mineralization; ferrihydrite and lepidocrocite were favored as solid phase Fe(III) and chelated Fe(III) (with nitrilotriacetic acid or EDTA) as soluble Fe(III) forms.     

Drop size-dependent S(IV) oxidation in chemically heterogeneous radiation fogs

Six radiation fog episodes were sampled in the Central Valley of California during winter 1998/1999. Drop size-resolved fog samples were sampled using a size-fractionating Caltech active strand cloudwater collector (sf-CASCC). The sf-CASCC collects a large fog drop sample, comprised mainly of drops larger than 17 μm diameter, and a small fog drop sample, comprised mainly of drops with diameters between 4 and 17 μm. The fog pH was found to vary between approximately pH 5.3 and 6.8, with the pH of the large fog drop sample typically several tenths of a pH unit higher than the simultaneously collected small fog drop sample. At these high pH values, dissolved sulfur dioxide can be rapidly oxidized by a variety of chemical pathways and also can react quickly with dissolved formaldehyde to form hydroxymethanesulfonate. The amount of sulfate produced by aqueous-phase oxidation during each fog episode was determined by application of a tracer technique. The ratio of large : small drop S(IV) oxidation was compared with theoretically predicted ratios of large : small drop S(IV) oxidation rates. Although the higher pH of the large fog drops should promote more rapid S(IV) oxidation by ozone, finite rates of mass transport into the large drops and an increasing rate of complexation of S(IV) by formaldehyde at high pH combine to depress theoretically predicted rates of aqueous sulfate production in large fog drops below rates expected for small fog drops. This prediction is supported by the tracer results that indicate the concentration of sulfate resulting from aqueous-phase S(IV) oxidation in small drops generally exceeded the concentration formed in large drops. These findings stand in sharp contrast to observations in acidic clouds at Whiteface Mountain, New York, where hydrogen peroxide was determined to be the dominant S(IV) oxidant and the rate of S(IV) oxidation was found to be independent of drop size.     

Enhanced chemical oxidation of aromatic hydrocarbons in soil systems

Fenton's destruction of benzene, toluene, ethylbenzene, and xylene (BTEX) was investigated in soil slurry batch reactors. The purpose of the investigation was to quantify the enhancement of oxidation rates and efficiency by varying process conditions such as iron catalyst (Fe(II) or Fe(III); 2, 5, and 10mM), hydrogen peroxide (H2O2; 30, 150, 300 mM), and metal chelating agents (l-ascorbic acid, gallic acid, or N-(2-hydroxyethyl)iminodiacetic acid). Rapid contaminant mass destruction (97% after 3h) occurred in the presence of 300 mM H2O2 and 10 mM Fe(III). An enhanced removal rate (>90% removal after 15 min and 95% removal after 3h) was also observed by combining Fe(III), N-(2-hydroxyethyl)iminodiacetic acid and 300 mM H2O2. The observed BTEX mass removal rate constants (3.6-7.8 x 10(-4)s(-1)) were compared to the estimated rate constants (4.1-10.1 x 10(-3)s(-1)). The influence of non-specific oxidants loss (by reaction with iron hydroxides and soil organic matter) was also explored.     

Phenol nitration upon oxidation of nitrite by Mn(III,IV) (hydr)oxides

An interesting aspect of the chemistry of nitrite is the possibility for this compound to interact with other environmental factors and many oxidising species, which results in the oxidation of nitrite to nitrogen dioxide. This is a potentially interesting process that can lead to the formation of nitroaromatic compounds in the environment. In previous papers we have shown that nitrite can interact with dissolved Fe(III) and nitrate under irradiation, Fenton and heterogeneous photo-Fenton reagents, and semiconductor oxides such as TiO2, alpha-Fe2O3, and beta-FeOOH under irradiation. This paper reports on the interaction between nitrite/nitrous acid and the Mn(III,IV) (hydr)oxides beta-MnO2 and gamma-MnOOH, both in neutral solution under irradiation and in acidic conditions in the dark. beta-MnO2 and gamma-MnOOH originate from the oxidation of Mn(II) and play a key role in the redox cycling of manganese in the environment. These Mn(III,IV) (hydr)oxides show some photocatalytic activity, and they can act as thermal oxidants at acidic pH. The photoinduced oxidation of nitrite and the thermal oxidation of nitrous acid by Mn(III,IV) (hydr)oxides yield nitrogen dioxide and lead to the formation of nitrophenols in the presence of phenol. These processes can take place at the water-sediment or water-colloid interface in natural waters and on the surface of atmospheric particulate. Furthermore, the phenol/gamma-MnOOH/HNO2 system in dark acidic solution is an interesting model due to the formation of phenoxyl radical upon phenol monoelectronic oxidation by gamma-MnOOH. The kinetics of nitrophenol generation under such conditions indicates that phenol nitration is unlikely to take place upon reaction between phenoxyl and *NO2 and suggests a solution to a literature debate on the subject.     

Experimental study and steady-state simulation of biogeochemical processes in laboratory columns with aquifer material

Packed bed laboratory column experiments were performed to simulate the biogeochemical processes resulting from microbially catalyzed oxidation of organic matter. These included aerobic respiration, denitrification, and Mn(IV), Fe(III) and SO(4) reduction processes. The effects of these reactions on the aqueous- and solid-phase geochemistry of the aquifer material were closely examined. The data were used to model the development of alkalinity and pH along the column. To study the independent development of Fe(III)- and SO(4)-reducing environments, two columns were used. One of the columns (column 1) contained small enough concentrations of SO(4) in the influent to render the reduction of this species unimportant to the geochemical processes in the column.The rate of microbially catalyzed reduction of Mn(IV) changed with time as evidenced by the variations in the initial rate of Mn(II) production at the head of the column. The concentration of Mn in both columns was controlled by the solubility of rhodochrosite (MnCO(3(S))).In the column where significant SO(4) reduction took place (column 2), the concentration of dissolved Fe(II) was controlled by the solubility of FeS. In column 1, where SO(4) reduction was not important, maximum dissolved Fe(II) concentrations were controlled by the solubility of siderite (FeCO(3(S))). Comparison of solid-phase and aqueous-phase data suggests that nearly 20% of the produced Fe(II) precipitates as siderite in column 1. The solid-phase analysis also indicates that during the course of experiment, approximately 20% of the total Fe(III) hydroxides and more than 70% of the amorphous Fe(III) hydroxides were reduced by dissimilatory iron reduction.The most important sink for dissolved S(-II) produced by the enzymatic reduction of SO(4) was its direct reaction with solid-phase Fe(III) hydroxides leading initially to the formation of FeS. Compared to this pathway, precipitation as FeS did not constitute an important sink for S(-II) in column 2. In this column, the total reacted S(-II) estimated from the concentration of dissolved sulfur species was in good agreement with the produced Cr(II)-reducible sulfur in the solid phase. Solid-phase analysis of the sulfur species indicated that up to half of the originally produced FeS may have possibly transformed to FeS(2).     

Persulfate oxidation for in situ remediation of TCE. II. Activated by chelated ferrous ion

In situ chemical oxidation (ISCO) is a technique used to remediate contaminated soil and groundwater systems. It has been postulated that sodium persulfate (Na2S2O8) can be activated by transition metal ions such as ferrous ion (Fe2+) to produce a powerful oxidant known as the sulfate free radical (SO4-*) with a redox potential of 2.6 V, which can potentially destroy organic contaminants. In this laboratory study persulfate oxidation of dissolved trichloroethylene (TCE) was investigated in aqueous and soil slurry systems under a variety of experimental conditions. A chelating agent (i.e., citric acid) was used in attempt to manipulate the quantity of ferrous ion in solution by providing an appropriate chelate/Fe2+ molar ratio. In an aqueous system a chelate/Fe2+ molar ratio of 1/5 (e.g., S2O8(2)-/chelate/Fe2+/TCE ratio of 20/2/10/1) was found to be the lowest acceptable ratio to maintain sufficient quantities of Fe2+ activator in solution resulting in nearly complete TCE destruction after only 20 min. The availability of Fe2+ appeared to be controlled by adjusting the molar ratio of chelate/Fe2+. In general, high levels of chelated ferrous ion concentrations resulted in faster TCE degradation and more persulfate decomposition. However, if initial ferrous ion contents are relatively low, sufficient quantities of chelate must be provided to ensure the chelation of a greater percentage of the limited ferrous ion present. Citric acid chelated ferrous ion appeared effective for TCE degradation within soil slurries but required longer reaction times. Additionally, the use of citric acid without the addition of supplemental Fe2+ in soil slurries, where the citric acid apparently extracted native metals from the soil, appeared to be somewhat effective at enhancing persulfate oxidation of TCE over extended reaction times. A comparison of different chelating agents revealed that citric acid was the most effective.     

In situ iron activated persulfate oxidative fluid sparging treatment of TCE contamination--a proof of concept study

In situ chemical oxidation (ISCO) is considered a reliable technology to treat groundwater contaminated with high concentrations of organic contaminants. An ISCO oxidant, persulfate anion (S(2)O(8)(2-)) can be activated by ferrous ion (Fe(2+)) to generate sulfate radicals (E(o)=2.6 V), which are capable of destroying trichloroethylene (TCE). The property of polarity inhibits S(2)O(8)(2-) or sulfate radical (SO(4)(-)) from effectively oxidizing separate phase TCE, a dense non-aqueous phase liquid (DNAPL). Thus the oxidation primarily takes place in the aqueous phase where TCE is dissolved. A bench column study was conducted to demonstrate a conceptual remediation method by flushing either S(2)O(8)(2-) or Fe(2+) through a soil column, where the TCE DNAPL was present, and passing the dissolved mixture through either a Fe(2+) or S(2)O(8)(2-) fluid sparging curtain. Also, the effect of a solubility enhancing chemical, hydroxypropyl-beta-cyclodextrin (HPCD), was tested to evaluate its ability to increase the aqueous TCE concentration. Both flushing arrangements may result in similar TCE degradation efficiencies of 35% to 42% estimated by the ratio of TCE degraded/(TCE degraded+TCE remained in effluent) and degradation byproduct chloride generation rates of 4.9 to 7.6 mg Cl(-) per soil column pore volume. The addition of HPCD did greatly increase the aqueous TCE concentration. However, the TCE degradation efficiency decreased because the TCE degradation was a lower percentage of the relatively greater amount of dissolved TCE by HPCD. This conceptual treatment may serve as a reference for potential on-site application.     

Arsenic(III) and iron(II) co-oxidation by oxygen and hydrogen peroxide: Divergent reactions in the presence of organic ligands

Iron-catalyzed oxidation of As(III) to As(V) can be highly effective for toxic arsenic removal via Fenton reaction and Fe(II) oxygenation. However, the contribution of ubiquitous organic ligands is poorly understood, despite its significant role in redox chemistry of arsenic in natural and engineered systems. In this work, selected naturally occurring organic ligands and synthetic ligands in co-oxidation of Fe(II) and As(III) were examined as a function of pH, Fe(II), H₂O₂, and radical scavengers (methanol and 2-propanol) concentration. As(III) was not measurably oxidised in the presence of excess ethylenediaminetetraacetic acid (EDTA) (i.e. Fe(II):EDTA < 1:1), contrasting with the rapid oxidation of Fe(II) by O₂ and H₂O₂ at neutral pH under the same conditions. However, partial oxidation of As(III) was observed at a 2:1 ratio of Fe(II):EDTA. Rapid Fe(II) oxidation in the presence of organic ligands did not necessarily result in the coupled As(III) oxidation. Organic ligands act as both iron speciation regulators and radicals scavengers. Further quenching experiments suggested both hydroxyl radicals and high-valent Fe species contributed to As(III) oxidation. The present findings are significant for the better understanding of aquatic redox chemistry of iron and arsenic in the environment and for optimization of iron-catalyzed arsenic remediation technology.     

Electroassisted methods for waste destruction: silver(II) and peroxydisulfate reagents in the electrochemically mediated oxidation of polyaromatic sulfonates

The electrochemical oxidation is a promising process for organic pollutants which are recalcitrant to biological degradation. The anodic oxidation of 1,5-naphthalenedisulfonic acid, hereafter NDS, was evaluated at a Pt anode using in situ generated Ag(II) cation or peroxydisulfate [S2O(8)(2-)] anion as mediators. Kinetics of the direct chemical oxidation of NDS in the presence of Na2S2O8, and the identification of some oxidation intermediates are also reported. An analysis of the results shows that Ag(II) is characterized by a high-reaction rates, while [S2O(8)(2-)] performs the oxidation of NDS in a complete way.