共查询到20条相似文献,搜索用时 15 毫秒
1.
The miscibility of cellulose acetate (CA; degree of substitution = 2.5) and poly(ethylene succinate) (PES) has been investigated
using a variety of thermal techniques and by solid-state carbon13 NMR spectroscopy. The blends containing greater than ca.
70% CA were found to be miscible. In the case of blends containing less than ca. 70% CA, a combination of thermal and NMR
analyses suggests that these blends are not fully miscible on a 2.5- to 5-nm scale. On the scale which can be probed by dynamic
mechanical thermal analysis (15 nm), the low-percentage CA blends exhibit “significant local concentration fluctuations≓.
Investigation of the biodegradation of the blend components and of the blends revealed that PES degraded relatively rapidly
and that CA degraded slowly. The blends degraded at a rate essentially identical to that of CA. Miscibility (75% CA blend)
or crystallization of PES (30% CA blend) had no significant effect. These data suggest that a significant mode of degradation
óf PES during composting involves chemical hydrolysis of the polymer followed by biological assimilation of monomers. Degradation
of the blends is initiated in the amorphous phase. Because CA is a significant component of the amorphous phase, a small amount
of CA significantly impacts the biodegradation rates of the blends. 相似文献
2.
Residual cellulose acetate (CA) films with initial degree of substitution (DS) values of 1.7 and 2.5 (CA DS-1.7 and DS-2.5) were recovered from a simulated thermophilic compost exposure and characterized by gel permeation chromatography (GPC), proton nuclear magnetic resonance ( 1H NMR), and scanning electron microscopy (SEM) to determine changes in polymer molecular weight and DS and to study microbial colonization and surface morphology, respectively. During the aerobic degradation of CA DS-1.7 and CA DS-2.5 films exposed for 7 and 18 days, respectively, the number-average molecular weight ( M
n) of residual polymer decreased by 30.4% on day 5 and 20.3% on day 16, respectively. Furthermore, a decrease in the degree of substitution from 1.69 to 1.27 (4-day exposure) and from 2.51 to 2.18 (12-day exposure) was observed for the respective CA samples. In contrast, CA films (DS-1.7 and DS-2.5) which were exposed to abiotic control vessels for identical time periods showed no significant changes in M
n and DS. SEM photographs of CA (DS-1.7 and DS-2.5) film surfaces after compost exposures revealed severe erosion and corresponding microbial colonization. Similar exposure times for CA films in abiotic control vessels resulted in only minor changes in surface characteristics by SEM observations. The conversion of CA DS-1.7 and DS-2.5 to CO 2 was monitored by respirometry. In these studies, powdered CA was placed in a predigested compost matrix which was maintained at 53°C and 60% moisture content throughout the incubation period. A lag phase of 10- and 25-day duration for CA DS-1.7 and DS-2.5, respectively, was observed, after which the rate of degradation increased rapidly. Mineralization of exposed CA DS-1.7 and DS-2.5 powders reported as the percentage theoretical CO 2 recovered reached 72.4 and 77.6% in 24 and 60 days, respectively. The results of this study demonstrated that microbial degradation of CA films exposed to aerobic thermophilic laboratory-scale compost reactors not only results in film weight loss but also causes severe film pitting and a corresponding decrease in chain M
n and degree of substitution for the residual material. Furthermore, conversions to greater than 70% of the theoretical recovered CO 2 for CA (DS 1.7 and 2.5) substrates indicate high degrees of CA mineralization.Guest Editor: Dr. Graham Swift, Rohm & Haas. 相似文献
3.
High polymer blends of Polymethyl methacrylate (PMMA) with cellulose acetate (CA) and Cellulose acetate phthalate (CAP) of varying blend compositions have been prepared to study their biodegradation behavior and blend miscibility. Films of PMMA–CA, and PMMA–CAP blends have been prepared by solution casting using Acetone and Dimethyl formamide(DMF) as solvents respectively. Biodegradability of these blends has been studied by four different methods namely, soil burial test, enzymatic degradation, and degradation in phosphate buffer and activated sludge degradation followed by water absorption tests to support the degradation studies. Degradation analysis was done by weight loss method. The results of all the tests showed sufficient biodegradability of these blends. Degradability increased with the increase in CA and CAP content in the blend compositions. The miscibility of PMMA–CA and PMMA–CAP blends have been studied by solution viscometric and ultrasonic methods. The results obtained reveal that PMMA forms miscible blends with either CA or CAP in the entire composition range. Miscibility of the blends may be due to the formation of hydrogen bond between the carbonyl group of PMMA and the free hydroxyl group of CA and CAP. 相似文献
4.
Nowadays, the importance of green and biodegradable plastics as viable substitutes for non-degradable petroleum-based materials is felt more than ever. Regenerated cellulose (RC) as a potential candidate suffers from poor processability and inferior properties, limiting its wide applications. In this study, it is demonstrated that citric acid (CA) enhances physical, mechanical, and thermal properties of RC films, due to RC-citric acid compatibility. 1-ethyl-3-methylimidazolium chloride (EMIMCl) as a green ionic liquid was employed for the processing of RC. The optimum properties in terms of thermal stability, mechanical strength, contact angle, water uptake, and oxygen permeability were achieved at 10 wt% of CA. However, further incorporation of CA adversely affected the film properties. This behaviour was explained by the crosslinking and plasticizing effects of CA. Furthermore, in vitro cytotoxicity test demonstrated that RC/CA films are cytocompatible, suggesting the potential advantage of using these biopolymeric films for biomaterial and biological applications. 相似文献
5.
In this account, we report our findings on blends of cellulose acetate having a degree of substitution (DS) of 2.49 (CA2.5) with a cellulose acetate having a DS of 2.06 (CA2.0). This blend system was examined over the composition range of 0–100% CA2.0 employing both solvent casting of films (no plasticizer) and thermal processing (melt-compressed films and injection molding) using poly(ethylene glycol) as a common plasticizer. All thermally processed blends were optically clear and showed no loss in optical quality after storage for several months. Thermal analysis and measurement of physical properties indicate that blends in the middle composition range are partially miscible, while those at the ends of the composition range are miscible. We suggest that the miscibility of these cellulose acetate blends is influenced primarily by the monomer composition of the copolymers. Bench-scale simulated municipal composting confirmed the biodestructability of these blends and indicated that incorporation of a plasticizer accelerated the composting rates of the blends. In vitro aerobic biodegradation testing involving radiochemical labeling conclusively demonstrated that both the lower DS CA2.0 and the plasticizer significantly enhanced the biodegradation of the more highly substituted CA2.5.While this work was in progress, Robert Gardner was struck with cancer and died on June 6, 1995. This paper is dedicated to his memory and to his contributions as a friend and colleague. 相似文献
6.
Due to the increase in energy cost by constantly high oil prices and the obligation to reduce greenhouse effect gases, landfill gas is frequently used as an alternative energy source for producing heat and electricity. Most of landfill gas utility facilities, however, are experiencing problems controlling siloxanes from landfill gas as their catalytic oxidizers are becoming fouled by silicon dioxide dust. To evaluate adsorption characteristics of siloxanes, an adsorption equilibrium test was conducted and parameters in the Freundlich and Langmuir isotherms were analyzed. Coconut activated carbon (CA1), coal activated carbon (CA2), impregnated activated carbon (CA3), silicagel (NCA1), and activated alumina (NCA2) were used for the adsorption of the mixed siloxane which contained hexamethyldisiloxane (L2), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). L2 had higher removal efficiency in noncarbon adsorbents compared to carbon adsorbents. The application of Langmuir and Freundlich adsorption isotherm demonstrated that coconut based CA1 and CA3 provided higher adsorption capacity on L2. And CA2 and NCA1 provided higher adsorption capacity on D4 and D5. Based on the experimental results, L2, D4, and D5 were converted by adsorption and desorption in noncarbon adsorbents. Adsorption affinity of siloxane is considered to be affect by the pore size distribution of the adsorbents and by the molecular size of each siloxane. 相似文献
7.
Cellulose acetate (CA) films with degree of substitution (d.s.) values of 1.7 and 2.5 were exposed to biologically active in-laboratory composting test vessels maintained at approximately 53 °C. The CA 1.7- and 2.5-d.s. films (thickness values of 0.5–1.0 and 2.0 mil, respectively) had completely disappeared by the end of 7- and 18-day exposure time periods in the biologically active bioreactors, respectively. The relatively small CA film weight loss observed in the poisoned control test vessels allows the conclusion that CA film erosion during the composting exposures resulted, at least in part, from biologically mediated processes. Under strictly anaerobic conditions, an active methanogenic inoculum was developed by acclimation of a sewage sludge to a synthetic municipal solid waste (SMSW) mixture at 42°C. The CA 1.7-d.s. film samples (0.5- to 1.0-mil thickness) were exposed in anaerobic serum bottles containing a 25% solids loading of SMSW in which methanogenic activity was rapidly established after introducing of the developed inoculum. For exposures of 30 days only small visually distinguishable fragments of the CA 1.7-d.s. films were recovered. In contrast, exposure of the CA 1.7-d.s. film to a poisoned control test vessel resulted in negligible weight loss. Therefore, degradation of the CA 1.7-d.s. films upon exposure to the anaerobic bioreactors was due, at least in part, to biologically mediated processes.Guest Editor: Dr. Graham Swift, Rohm & Haas. 相似文献
8.
Cellulose acetate (CA) was synthesized from knitted rag, a cellulosic waste of Textile and Garment industries, in the glacial acetic acid, and subsequently acetic anhydride (Ac 2O) in presence of concentrated H 2SO 4 reaction medium. A low to high substitution products were obtained from single step up to seven steps acetylation of cellulose. In this way, it was possible to produce low cost and different grades or substituted acetylation derivatives of cellulose. The synthesized CA was characterized and investigation of its physical characteristics was done. Solubility, acetyl content, acetic acid content, degree of substitution, and molecular weight of CA increased gradually with the increase of the number of reaction steps attaining optimum value at the fourth step. The acetyl and acetic acid content of CA were increased from 39.95 % to 44.25 %, and from 55.73 % to 61.73 % respectively. Similarly, degree of substitution and molecular weight of CA were increased from 2.47 to 2.94, and from 74,249 to 121,437 respectively. 相似文献
9.
Starch/polyvinyl alcohol (PVA) blend films were prepared successfully by using starch, polyvinyl alcohol (PVA), glycerol (GL) sorbitol (SO) and citric acid (CA) for the mixing process. The influence of mixing time, additional materials and drying temperature of films on the properties of the films was investigated. With increase in mixing time, the tensile strength (TS), elongation (%E), degree of swelling (DS) and solubility (S) of the film were equilibrated. The equilibrium for TS, %E, DS and S value was 20.12 MPa, 36.98%, 2.4 and 0.19, respectively. The mixing time of equilibrium was 50 min. TS, %E, DS and S of starch/PVA blend film were examined adding glycerol (GL), sorbitol (SO) and citric acid (CA) as additives. At all measurement results, except for DS, the film adding CA was better than GL or SO because hydrogen bonding at the presence of CA with hydroxyl group and carboxyl group increased the inter/intramolecular interaction between starch, PVA and additives. Citric acid improves the properties of starch/PVA blend film compared to glycerol and sobitol. When the film was dried at low temperature, the properties of the films were clearly improved because the hydrogen bonding was activated at low temperature. 相似文献
10.
Previous research in our laboratory reported a convenient laboratory-scale composting test method to study the weight loss of polymer films in aerobic thermophilic (53°C) reactors maintained at a 60% moisture content. The laboratory-scale compost reactors contained the following synthetic compost mixture (percentage on dry-weight basis): tree leaves (45.0), shredded paper (16.5), food (6.7), meat (5.8), cow manure (17.5), sawdust (1.9), aluminum and steel shavings (2.4), glass beads (1.3), urea (1.9), and a compost seed (1.0) which is designated Mix-1 in this work. To simplify the laboratory-scale compost weight loss test method and better understand how compost mixture compositions and environmental parameters affect the rate of plastic degradation, a systematic variation of the synthetic mixture composition as well as the moisture content was carried out. Cellulose acetate (CA) with a degree of substitution (DS) value of 1.7 and cellophane films were chosen as test polymer substrates for this work. The extent of CA DS-1.7 and cellophane weight loss as a function of the exposure time remained unchanged when the metal and glass components of the mixture were excluded in Mix-2. Further study showed that large variations in the mixture composition such as the replacement of tree leaves, food, meat, and sawdust with steam-exploded wood and alfalfa (forming Mix-C) could be made with little or no change in the time dependence of CA DS-1.7 film weight loss. In contrast, substituting tree leaves, food, meat, cow manure, and sawdust with steam-exploded wood in combination with either Rabbit Choice (Mix-D) or starch and urea (Mix-E) resulted in a significant time increase (from 7 to 12 days) for the complete disappearance of CA DS-1.7 films. Interestingly, in this work no direct correlation was observed between the C/N ratio (which ranged from 13.9 to 61.4) and the CA DS-1.7 film weight loss. Decreasing moisture contents of the compost Mix-2 from 60 and 50 and 40% resulted in dramatic changes in polymer degradation such that CA DS-1.7 showed an increase in the time period for a complete disappearance of polymer films from 6 to 16 and 30 days, respectively.Guest Editor: Dr. Graham Swift, Rohm & Haas.Paper presented at the Bio/Environmentally Degradable Polymer Society—Second National Meeting, August 19–21, 1993, Chicago, Illinois. 相似文献
11.
A life cycle assessment (LCA) focused on biochar and bioenergy generation was performed for three thermal treatment configurations (slow pyrolysis, fast pyrolysis and gasification). Ten UK biodegradable wastes or residues were considered as feedstocks in this study. Carbon (equivalent) abatement (CA) and electricity production indicators were calculated. Slow pyrolysis systems offer the best performance in terms of CA, with net results varying from 0.07 to 1.25tonnes of CO(2)eq.t(-1) of feedstock treated. On the other hand, gasification achieves the best electricity generation outputs, with results varying around 0.9MWhet(-1) of feedstock. Moreover, selection of a common waste treatment practice as the reference scenario in an LCA has to be undertaken carefully as this will have a key influence upon the CA performance of pyrolysis or gasification biochar systems (P/GBS). Results suggest that P/GBS could produce important environmental benefits in terms of CA, but several potential pollution issues arising from contaminants in the biochar have to be addressed before biochar and bioenergy production from biodegradable waste can become common practice. 相似文献
12.
To improve the heavy metal ion chelating ability and the microbiological stability of chitosan (CS), l-arginine ( l-Arg) was grafted on CS polymer in the presence of the condensing agent 1-(3-dimethylaminopropyl)-3-ethylcarbodiimide (EDC) and the coupling reagent N-hydroxysuccinimide (NHS) to prepare a natural polymer-based environmental rehabilitation material: l-arginine-grafted chitosan (CA). The graft mechanism is discussed, and the reaction conditions were optimized. The product was characterized using elemental analysis, infrared spectroscopy (FT-IR) and 13C-NMR spectroscopy ( 13C-NMR). The optimal reaction conditions were a reactant molar ratio nCS:nArg:nEDC:nNHS of 3:3:3:1, a reaction time of 12 h, and a reaction system pH?=?5. Under these conditions, the grafting ratio (GR) was 16.85%, while the product yield (PY) was 90.48%. The results of the adsorption experiments showed that the CA (GR?=?16.85%) had a better removal capacity for highly concentrated Cu 2+ and Ni 2+ ions than CS. The antibacterial activity of the CA was also enhanced. When the GR reached 16.85%, the CA almost completely inhibited the growth of colibacillus and Staphylococcus aureus. Due to its high chelating ability and microbiological stability, this novel metal-ion adsorption material, CA, can be considered to have broad application potential in heavy metal ion-polluted water and soil remediation. 相似文献
13.
All-cellulose composite fibers were produced by electrospinning dispersions containing cellulose acetate (CA) and cellulose nanocrystals (CNCs). Precursor polymer matrices were obtained after dispersion of CA with different degrees of substitution in a binary mixture of organic solvents. The obtained fibers of CA loaded with CNCs had typical widths in the nano- and micro-scale and presented a glass transition temperature of 145?°C. The CA component was converted to cellulose by using alkaline hydrolysis to yield all-cellulose composite fibers that preserved the original morphology of the precursor system. Together with Fourier Transform Infrared Spectroscopy fingerprints the thermal behavior of the all-cellulose composite fibers indicated complete conversion of cellulose acetate to regenerated cellulose. Noticeable changes in the thermal, surface and chemical properties were observed upon deacetylation. Not only the thermal transitions of cellulose acetate disappeared but the initial water contact angle of the web was reduced drastically. Overall, we propose a simple method to produce all-cellulose composite fibers which are expected to display improved thermo-mechanical properties while keeping the unique features of the cellulose polymer. 相似文献
14.
Journal of Polymers and the Environment - With the objective to assess the suitability of cellulose acetate (CA), polysulfone (PSF) and silica (SiO2) for wastewater treatment, this work presents... 相似文献
15.
In this study, dry sewage sludge (DSS) as the principal material was blended with coal ash (CA) to produce lightweight aggregate. The effects of different raw material compositions and sintering temperatures on the aggregate properties were then evaluated. In addition, an environmental assessment of the lightweight aggregate generated was conducted by analyzing the fixed rate of heavy metals in the aggregate, as well as their leaching behavior. The results indicated that using DSS enhanced the pyrolysis–volatilization reaction due to its high organic matter content, and decreased the bulk density and sintering temperature. However, the sintered products of un-amended DSS were porous and loose due to the formation of large pores during sintering. Adding CA improved the sintering temperature while effectively decreasing the pore size and increasing the compressive strength of the product. Furthermore, the sintering temperature and the proportion of CA were found to be the primary factors affecting the properties of the sintered products, and the addition of 18–25% of CA coupled with sintering at 1100 °C for 30 min produced the highest quality lightweight aggregates. In addition, heavy metals were fixed inside products generated under these conditions and the As, Pb, Cd, Cr, Ni, Cu, and Zn concentrations of the leachate were found to be within the limits of China’s regulatory requirements. 相似文献
16.
Journal of Polymers and the Environment - Novel metal-free catalysts were synthesized form maleic acid (MA) and citric acid (CA) based polymers for hydrogen generation form NaBH4.... 相似文献
17.
The current study proposes a novel and improved cigarette filtration design comprising cellulose nanofibers (CNFs) and powdered activated carbons (PACs) with different dry matter contents. The proposed filter samples were primarily analyzed to verify their applicability as cigarette filters via measurements and standard tests, such as SEM, BET, DSC, and airflow permeability analysis. The results were compared with the cellulose acetate (CA) sample used as a conventional cigarette filter. The preliminary results indicated noticeable improvement compared to the reference CA. Also, the cigarettes were tested using a smoking machine, and the filtered smoke was analyzed using GC–MS to evaluate the filters' performance in reducing the harmful substances present in the smoke. The results showed that the filters made of CNF and PAC significantly decreased the toxic substances compared with the reference but did not affect the nicotine substantially and therefore will not negatively impact the trance level of smokers. 相似文献
18.
The effects of three compounded curing agents on the properties and performance of the urea-formaldehyde (UF) resin were investigated in this study. The compounded curing agents were prepared by mixing ammonium chloride with hexamethylenetetramine, citric acid, and oxalic acid respectively at a ratio of 1:1, named N-H, N–CA, and N–OA, respectively. The curing process, crystallinity, and physical properties were measured, and the three-ply plywood was fabricated to measure its prepress strength, wet shear strength, and formaldehyde emission. Results showed that the compounded curing agents N–CA and N–OA enhanced the initial viscosity, crosslinking density and thermal stability of UF resin. Additionally, the prepress strength of the plywood bonded by UF resin with N–CA and N–OA increased by 82 and 111% respectively compared to the UF resin with NH 4Cl, and the wet shear strength increased by 14 and 16%, the formaldehyde emission decreased by 19 and 42% respectively. However, owing to the short pot-life of these curing agent limited their storage time, the curing agents N–CA and N–OA should be applied to fabricate plywood in winter for obtaining a better bond strength and a lower formaldehyde emission. While the UF resin with N–HT showed a suitable pot-life, so it could be applied to fabricate plywood in summer for long time storage and avoiding procuring problem. 相似文献
19.
In this paper, we report on the physical properties of films that have been synthesized by using native corn starch (NS) and
chemically modified starch (RS4). NS or RS4/PVA blend films were synthesized by using the mixing process and the casting method.
Glycerol (GL), sorbitol (SO), and citric acid (CA) were used as additives. The chemically modified starch (RS4) was synthesized
by using sodium trimetaphosphate (STMP) and sodium tripolyphosphate (STPP) as a crosslinker. Then, the RS4 thus synthesized
was confirmed by using the pancreatin-gravimetric method, swelling power and an X-ray diffractometer (XRD).
Tensile strength (TS), elongation (% E), swelling behavior (SB), and solubility ( S) of the films were measured. The result of the measurements indicated the RS4-added film was better than the NS-added film.
Especially, the RS4/PVA blend film with CA as an additive showed the physical properties superior to other films. 相似文献
20.
Biodegradable films were successfully prepared by using cornstarch (CS), chemically modified starch (RS4), polyvinyl alcohol
(PVA), glycerol (GL), and citric acid (CA). The physical properties and biodegradability of the films using CS, RS4, and additives
were investigated. The results of the investigation revealed that the RS4-added film was better than the CS-added film in
tensile strength (TS), elongation at break (% E), swelling behavior (SB) and solubility ( S). Especially, the RS4/PVA blend film with CA as an additive showed physical properties superior to other films. Furthermore,
when the film was dried at low temperature, the properties of the films clearly improved because the hydrogen bonding was
activated at low temperature. The biodegradation of films was carried out using the enzymatic, microbiological and soil burial
test. The enzyme used in this study was amyloglucosidase (AMG), α-amylase (α-AM) and β-amylase (β-AM). At the enzymatic degradation
test, the GL-added films had an approximately 60% degradation, while the CA-added films were degraded about 25%. The low degradation
value on CA-added film is attributed to low pH of film added CA that deactivated the enzymatic reaction. The microbiological
degradation teat was performed by using Bacillus subtilis and Aspergillus niger. 相似文献
|