Comparison of Polylactic Acid/Kenaf and Polylactic Acid/Rise Husk Composites: The Influence of the Natural Fibers on the Mechanical, Thermal and Biodegradability Properties

This paper investigates and compares the performances of polylactic acid (PLA)/kenaf (PLA-K) and PLA/rice husk (PLA-RH) composites in terms of biodegradability, mechanical and thermal properties. Composites with natural fiber weight content of 20% with fiber sizes of less than 100 μm were produced for testing and characterization. A twin-screw extrusion was used to compound PLA and natural fibers, and extruded composites were injection molded to test samples. Flexural and Izod impact test, TGA, soil burial test and SEM were used to investigate properties. All results were compared to a pure PLA matrix sample. The flexural modulus of the PLA increased with the addition of natural fibers, while the flexural strength decreased. The highest impact strength (34 J m⁻¹), flexural modulus (4.5 GPa) and flexural strength (90 MPa) were obtained for the composite made of PLA/kenaf (PLA-K), which means kenaf natural fibers are potential to be used as an alternative filler to enhance mechanical properties. On the other hand PLA-RH composite exhibits lower mechanical properties. The impact strength of PLA has decreased when filled with natural fibers; this decrease is more pronounced in the PLA-RH composite. In terms of thermal stability it has been found that the addition of natural fibers decreased the thermal stability of virgin PLA and the decrement was more prominent in the PLA-RH composite. Biodegradability of the composites slightly increased and reached 1.2 and 0.8% for PLA-K and PLA-RH respectively for a period of 90 days. SEM micrographs showed poor interfacial between the polymer matrix and natural fibers.     

Comparative Biodegradation Study of Starch- and Polylactic Acid-Based Materials

The degradation of starch- and polylactic acid-based plastic films by microorganisms extracted from compost was studied in a liquid medium. The various degradation products produced were measured throughout the duration of the experiment, and total carbon balances were estimated. For an easily biodegradable material, the evolution of the way carbon repartitioned between different degradation products was quite similar whatever the experimental condition or the type of substrate. On the other hand, for a resistant material exposed to these microorganisms, the nature of the biodegradation depended strongly on the experimental conditions. In the latter case, a differential scanning calorimetry analysis confirmed the importance of the applied norm on the state of the residual material. The consequences for improved methods of estimation of biodegradability of these materials are discussed.     

超声光催化降解酸性粒子元青染料的研究

对超声波作用下的纳米TiO2光催化氧化法降角酸性粒子元青染料进行了研究。结果表明，超声波的引入提高了纳米TiO2光催化降解酸性粒子元青染料的降解率；降解率受反应时间、坡声波功率、空气流量的影响；添加少量的H2O2能够明显地提高酸性粒子元青染料的降解率。     

Effects of Temperature and Relative Humidity on Polylactic Acid Plastic Degradation

Three high molecular weight (120,000 to 200,000 g mol^–1) polylactic acid (PLA) plastic films from Chronopol (Ch-I) and Cargill Dow Polymers (GII and Ca-I) were analyzed for their degradation under various temperature and relative humidity (RH) conditions. Two sets of plastic films, each containing 11 samples, were randomly hung in a temperature/humidity-controlled chamber by means of plastic-coated paper clips. The tested conditions were 28, 40, and 55°C at 50 and 100% RH, respectively, and 55°C at 10% RH. The three tested PLA films started to lose their tensile properties when their weight-average molecular weight (M _w) was in the range of 50,000 to 75,000 g mol^–1. The average degradation rate of Ch-I, GII, and Ca-I was 28,931, 27,361, and 63,025 M _w/week, respectively. Hence, GII had a faster degradation rate than Ch-I and Ca-I under all tested conditions. The degradation rate of PLA plastics was enhanced by the increase in temperature and relative humidity. This trend was observed in all three PLA plastics (Ca-I, GII, and Ch-I). Of the three tested films, Ch-I was the first to lose its mechanical properties, whereas Ca-I demonstrated the slowest loss, with mechanical properties under all tested conditions.     

Physicochemical Properties of Composite Materials Based on Thermoplastic Yam Starch and Polylactic Acid Improved with the Addition of Epoxidized Sesame Oil

Journal of Polymers and the Environment - Biodegradable materials provide a primary function in preserving and protecting food products, helping to extend shelf life. The present work aims to...     

Influence of Ozonized Soybean Oil as a Biobased Plasticizer on the Toughness of Polylactic Acid

Journal of Polymers and the Environment - This work aimed to study the mechanism of toughness improvement of polylactic acid (PLA) by using a biobased plasticizer. Ozonized soybean oil (OSBO),...     

Effect of Hydrothermal Polylactic Acid Degradation on Polymer Molecular Weight and Surface Properties

In the present work, polylactic acid, PLA, samples were degraded by hydrothermal treatment, and then their molecular weights, crystallinity, surface charges and compositions, were determined, respectively, by using viscometry, ¹H NMR, Differential Scanning Calorimetry (DSC), microelectrophoresis and Infra Red spectroscopy methods. The viscometry and ¹H NMR data indicate that the molecular weight, of the polymer, decreases after the hydrothermal treatment. However, the crystalline fractions of the PLA samples, as obtained from the DSC and X-ray data, were not altered after the hydrothermal treatment. Furthermore, the zeta potential data, as determined by microelectrophoresis, show for both non-degraded and degraded PLA, an increase of the polymer surface charge density with the pH of the aqueous phase. However, at acidic pH values, the surface charge density for the degraded PLA was higher as compared to the non degraded one. These differences in surface charge densities of the PLA samples were confirmed by Infrared study, according to which the spectra of degraded polymer show the appearance of carboxyl groups occurring at 1,600 cm⁻¹ at the polymer surface.     

Nano-TiO2 Modified Wheat Straw/Polylactic Acid Composites Based on Synergistic Effect Between Interfacial Bridging and Heterogeneous Nucleation

Journal of Polymers and the Environment - To improve the interfacial compatibility of wheat straw/polylactic acid (WS/PLA) composites, nano-TiO2 with different particle sizes was blended with...     

Cradle-to-Grave Life Cycle Assessment and Techno-Economic Analysis of Polylactic Acid Composites with Traditional and Bio-Based Fillers

This research focused on life cycle assessment (LCA) and techno-economic analysis (TEA) comparisons of polylactic acid (PLA) composites, in order to compare organic to inorganic fillers. Organic fillers included DDGS, flax, hemp, rice husks, and wood, and were compared against inorganic fillers (glass and talc) for PLA-based composites. This study utilized LCAI and TEA methodology to estimate and quantify costs, emissions, and energy intensity (EI) associated with material acquisition, processing, transport, and end-of-life treatment used during plastic composite production. Emission categories analyzed include global warming potential (GWP), air acidification (AA), air eutrophication (AE), water eutrophication (WE), ozone layer depletion (OLD), air smog (AS), high carcinogens (HC), and high non-carcinogens (HNC). To achieve a “Cradle-to-Grave” perspective, two models were meshed, the plastic comparator (PC) and EIO-LCA (EIO), to simulate the EI and emissions associated over the entire life cycle. Based assumptions used, this research has shown that utilizing land fill end-of-life treatment and glass filler composite was the most environmentally harmful option, and maintained the highest economic impact, for all impact categories during PLA composite production. Alternatively, both DDGS and wood filler composites paired with recycling end-of-life treatment were shown to be the least environmentally damaging method and incurred the lowest cost of all PLA composites considered. This study also suggests that utilization of organic bio-based fillers produces a lower economic/environmental impact, and EI, compared to utilization of inorganic fillers in PLA composites. Accordingly, this research has demonstrated the impact of LCA/TEA paired analysis when assessing the bioplastic and biocomposite processing, which may be utilized as a precursor for parallel research undertakings.     

Polylactic Acid Composites Utilising Sequential Surface Treatments of Lignocellulose: Chemistry,Morphology and Properties

Polylactic acid (PLA)—maple fibre composites have been synthesised using a series of sequentially modified cellulose fibres (namely alkylation followed by either acetylation or silanation). Confirmations of the sequential modifications were made using Fourier Transform Infrared Spectroscopy and Inductively Coupled Plasma—Atomic Emission Spectroscopy and the new surface morphologies analysed using Scanning Electron Microscopy. The key advantage of the use of sequential treatments (with initial alkali treatment) was the allowance for direct grafting of suitable chemical groups onto the cellulose in the fibre due to the removal of lignin, hemicellulose and other surface impurities. However, a balance was found to exist between alkali exposure time, concentration and resulting fibre integrity. The conditions used resulted in a loss in fibre weight, fibre moisture content and tensile strength. Sequential treatments with acetylation or silane resulted in a 15–21% strength recovery from that of the alkali treated composite. Factors that influenced this recovery in strength were the improved fibre-polymer interface, namely the hydrophilic balancing of the fibres and this further affected the thermal-hydrolysis of the PLA during composite fabrication.     

Photodegradation and Biodegradation Study of a Starch and Poly(Lactic Acid) Coextruded Material

To simulate the behavior of agricultural mulch coextruded poly(lactic acid)(PLA)/starch films, two stages were carried out. The first was an ultraviolet treatment (UV) at 315 nm, during which glass transition temperature T_g, weight, and molecular weight (MW) decreased and a separation between PLA and starch phase was observed. For the second stage, the mineralization of the carbon of the material was followed using the ASTM (D 5209–92 and 5338–92) and ISO/CEN (14852 and 14855) standard procedures. To measure the biodegradability of polymer material, the assessment of the carbon balance allowed determination of the distribution between the carbon rate used to the biomass synthesis or the respiration process (released CO₂), as well as the dissolved organic carbon into the culture medium and the carbon in the residual insoluble material. The influence of the nature of the medium and the standardized procedures on the final rate of biodegradation was investigated. Whatever the standardized method, the biodegradation percentage was significantly stronger in liquid medium (92.4–93.4) than on inert medium (80–83%). In the case of the compost process, only released CO₂ was measured and corresponded to 79.1–80.3%.     

Aging of Toughened Polylactic Acid Nanocomposites: Water Absorption,Hygrothermal Degradation and Soil Burial Analysis

The environmental aging behaviour of montmorillonite (MMT) filled polylactic acid (PLA) nanocomposites (PLA/MMT) and linear low density polyethylene (LLDPE)-toughened PLA (PLA/LLDPE ratio = 90/10) nanocomposites (PLA/LLDPE/MMT) were investigated in this study. The nanocomposites were subjected to water absorption, hygrothermal degradation and soil burial analysis. Both PLA/MMT and PLA/LLDPE/MMT nanocomposites were immersed in distilled water at three different temperatures (room temperature, 60, and 90 °C) and the weight difference before and after immersion was calculated. The kinetics of water absorption for both nanocomposites followed the Fick’s second law of diffusion, where a linear relationship exists between the initial moisture absorption at any time t and t ^1/2 (the square root of time), followed by a horizontal plateau (saturation). The equilibrium moisture content (M _m ) and diffusion coefficient (D) of PLA nanocomposites increased with the addition of MMT (2 phr) and LLDPE. However, the D values of both nanocomposites decreased by increasing MMT (4 phr). The M _m for PLA/MMT and PLA/LLDPE/MMT nanocomposites increased by increasing immersion temperature (60 °C) and prolonged immersion resulted in hygrothermal degradation of both nanocomposites. The hygrothermal degradation studies showed that PLA degrades much faster at 90 °C as compared to 60 °C in both the nanocomposites. The addition of MMT and LLDPE improved the hygrothermal stability of PLA in both nanocomposites. Soil burial test revealed deterioration of impact strength in all samples while the rate of biodegradation was retarded in the presence of MMT and LLDPE.     

Elaboration and Characterization of Nano-Biocomposites Based on Plasticized Poly(Hydroxybutyrate-Co-Hydroxyvalerate) with Organo-Modified Montmorillonite

Nano-biocomposites based on a biodegradable bacterial copolyester, poly(hydroxybutyrate-co-hydroxyvalerate), have been elaborated with an organo-modified montmorillonite (OMMT) clay as nanofiller, and acetyl tributyl citrate as plasticizer. The corresponding (nano)structures, thermal and mechanical properties, permeability, and biodegradability have been determined. Polyhydroxyalkanoates are very thermal sensitive then to follow the degradation the corresponding matrices have been analyzed by size exclusion chromatography. The results indicate that the addition of the plasticizer decreases the thermo-mechanical degradation, during the extrusion. These nano-biocomposites show an intercalated/exfoliated structure with good mechanical and barrier properties, and an appropriated biodegradation kinetic. Intending to understand the changes in the thermal properties, the nano-biocomposites were characterized by thermal gravimetric analysis and differential scanning calorimetry. The presence of the OMMT clay did not influence significantly the transition temperatures. However, the filler not only acted as a nucleating agent which enhanced the crystallization, but also as a thermal barrier, improving the thermal stability of the biopolymer. The results indicated that the addition of the plasticizer reduces the glass transition temperature and the crystalline melting temperature. The plasticizer acts as a processing aid and increases the processing temperature range (lower melting temperature).     

The Effect of Polymeric Chain Extenders on Physical Properties of Thermoplastic Starch and Polylactic Acid Blends

The effects of a polymeric chain extender on the properties of bioplastic film made from blends of plasticized polylactic acid (p-PLA) and thermoplastic starch (TPS) were studied. Joncryl^? ADR 4370S, a polymeric chain extender, was blended with TPS and p-PLA at a level of 1% (w/w). A co-rotating twin-screw extrusion process was used to prepare films with various ratios of TPS and p-PLA. Mechanical and physical properties of films, including film tensile properties, surface energy, moisture content, hydrophilicity, moisture sorption behaviour and thermal mechanical properties were determined. During extrusion, films enhanced by 1% Joncryl addition demonstrated more desirable and consistent qualities, such as smoother film edge and surface. Addition of Joncryl significantly improved film tensile strength, 0.2% offset yield strength, and elongation, especially evident with the 250% elongation of 70/30 (TPS/p-PLA) film. Total surface energy of films was not significantly influenced by addition of Joncryl. However, the polar contribution to the total surface energy of 70/30 (TPS/p-PLA) film increased after the addition of Joncryl. The study showed that blending TPS with p-PLA transformed TPS film from being highly hydrophilic to highly hydrophobic. On the other hand, addition of Joncryl had limited effects on moisture content, water solubility, glass transition temperature and moisture sorption behaviour of TPS/p-PLA blend films.     

Effects of Electron-Beam Irradiation and Ultraviolet Light (365 nm) on Polylactic Acid Plastic Films

Strips of Ca-I [polylactic acid (PLA) monolayer plastic films from Cargill Dow Polymers LLC, Minnetonka, MN] cut in the machine and nonmachine directions were irradiated with an electron beam using a CIRCLE III Linear Accelerator (MeV Industries S.A., Jouy-en-Josas, Cedex, France). The effects of 33-kGy irradiation on the physical properties of the Ca-I strips were studied. In addition, the effects of ultraviolet (UV) light (365-nm) illumination on the degradation of three PLA plastic films, Ch-I (PLA monolayer plastic films from Chronopol, Golden, CO), GII (PLA trilayer plastic films from Cargill Dow Polymers LLC), MN), and Ca-I (PLA monolayer plastic films from Cargill Dow Polymers LLC) were analyzed by a modified ASTM D5208-91 method. Results showed that irradiation had decreased the weight-average molecular weight (M_w), stress at break, percentage of elongation, and strain energy of Ca-I by 35.5, 26.7, 32.3, and 44.8%, respectively (P < 0.01). The shelf life of the irradiated Ca-I strips at 5°C and <20 ± 5% RH was about 6 months. The degradation rate of Ch-I, GII, and Ca-I with no UV light treatment at 55°C and 10% RH was 2512, 5618, and 3785 M_w/week, respectively. Under the UV light illumination (365 nm), the degradation rate of Ch-I, GII, and Ca-I, was 2982, 8722, and 7467 M_w/week, respectively. Hence, the degradation rate of GII and Ca-I was increased 55 and 97% by UV light (P < 0.008), respectively. This trend was not observed in Ch-I because its starting M_w (78,000 g/mol) was close to the tensile strength lost range (50,000 to 75,000 g/mol) of PLA films. To our knowledge, this is the first study to demonstrate that UV light does further enhance the degradation of PLA films.     

Hydrolysis of Polylactic Acid (PLA) and Polycaprolactone (PCL) in Aqueous Acetonitrile Solutions: Autocatalysis

Polylactic acid (PLA) is a hydrolytically degradable aliphatic polyester. The rate of polymer hydrolysis increases with time, and that has been attributed to the high reactivity of the terminal ester and the kinetics of autocatalysis. Hydrolysis is carried out in an acetonitrile/water solution to eliminate any solid-state contributions such as diffusion and crystallinity to the degradation process. A kinetic equation is derived to describe the autocatalytic effect of the increasing carboxylic acid end-group concentration. The results of solution hydrolysis are examined and found to fit the derived equation. Hydrolysis was also carried out with polycaprolactone (PCL) in acetonitrile, where reaction kinetics were found to differ from those of PLA. The PCL polymer required external acid catalysis by the addition of HCl, whereas hydrolysis of PLA was selfcatalyzed by the carboxylic acid end-groups.     

Processing Stability and Biodegradation of Polylactic Acid (PLA) Composites Reinforced with Cotton Linters or Maple Hardwood Fibres

Polylactic acid (PLA) composites comprising up to 25 wt% cotton linter (CL) or up to 50 % maple wood fibre (WF) were prepared by compounding and injection moulding. A reduction of crystallinity in the PLA matrix was observed as a result of the thermal processing method. These PLACL and PLAWF composites provided excellent improvements in both stiffness (with increases in tensile and flexural modulus) and toughness (increases in notched impact strength) properties over the neat PLA resin, while the tensile and flexural strengths of the composites were generally unchanged, while the strain at break values were reduced in comparison to the neat PLA. DMA results indicated incorporating these fibres caused the mechanical loss factor (tan δ) to decrease, suggesting better damping capabilities were achieved with the composites. SEM analysis of the impact fractured surfaces of the PLACL composites showed debonding-cavitation at the matrix-fibre interface while the PLAWF composites showed good wetting along its matrix-fibre interface. The composting of these composites up to 90 days showed that the degradation onset time was increased when increasing the fibre loadings, but the maximum degree of degradation and the maximum daily rates of degradation were decreased compared to neat PLA. On a weight basis of fibre loading, the PLACL composites had a quicker onset of biodegradation, a higher maximum daily rate of biodegradation and, overall, a higher degree of biodegradation at 90 days than the PLAWF composites, possibly due to the quicker thermal hydrolysis observed in the PLA matrix of the PLACL composites during processing and composting.     

Natural Weathering of Kenaf Bast Fibre-Filled Poly(Butylene Succinate) Composites: Effect of Fibre Loading and Compatibiliser Addition

Natural weathering was performed on poly(butylene succinate) (PBS) and its kenaf bast fibre (KBF) filled composites by exposing the specimens to a tropical climate for a period of 6 months (max–min temperature: 31.5–23.9 °C; relative humidity: 78.9%). The aim of this study was to investigate the effects of KBF loading and the addition of maleated PBS compatibiliser (PBSgMA) on the performance of the composites under natural weathering. As expected, the flexural properties of both the uncompatibilised and compatibilised composites dropped with increasing exposure time. The weathered specimens were also assessed by colour change analysis, FTIR spectroscopy analysis and SEM examination. The total colour change, ΔE _ab , of both the uncompatibilised and compatibilised composites increased with weathering time. FTIR spectroscopy analysis confirmed the presence of oxidation products such as hydroxyl, carbonyl and vinyl species in the weathered uncompatibilised and compatibilised composites. SEM examination revealed the presence of surface defects such as cracking, tiny holes and degraded fibre, which explain the poor performance of the composites upon weathering.     

Preparation of Alginic Acid and Metal Alginate from Algae and their Comparative Study

Alginic acid and metal alginates are prepared from fresh algae using extraction method. A FTIR spectrum indicates that alginic acid is converted into the metal alginate. Comparing calcium and cobalt alginates, asymmetric stretching of free carboxyl group of calcium alginate at 1630 cm⁻¹ is shifted to 1585 cm⁻¹ in cobalt alginate, due to the change of charge density, radius and atomic weight of the cation, creating a new environment around the carbonyl group. The strong exothermic peak of alginic acid in DSC thermogram indicates the decomposition of biopolymer, whereas strong exothermic peak of metal alginate in DSC thermogram attributed to the decomposition of biopolymer and formation of respective carbonate. Based on DSC study, the decomposition of cobalt alginate occurs at higher temperature comparing to those of sodium and calcium alginate, which may conclude into the higher stability of cobalt alginate. TGA results reveal that, cobalt alginate is more stable than calcium and sodium alginate at 300 °C temperature. Surface morphology (at same magnification), as well as porosity (%) and pore size distribution results change with metals present in different metal alginates.     

Study on the Effect of Dicumyl Peroxide on Structure and Properties of Poly(Lactic Acid)/Natural Rubber Blend

In attempt to enhance the compatibility of NR in PLA matrix, and furthermore to enhance mechanical properties of PLA, PLA/NR blends with strong interaction were prepared in Haake internal mixer, using dicumyl peroxide (DCP) as cross-linker. The effects of dicumyl peroxide on morphology, thermal properties, mechanical properties and rheological properties of PLA and PLA/NR blends were studied. The results indicated that dicumyl peroxide could increase the compatibility of poly(lactic acid) and natural rubber. With small amount of dicumyl peroxide, the effect on NR toughening PLA was enhanced and the tensile toughness of PLA/NR blends was improved. When the DCP content was up to 0.2 wt%, the PLA/NR blend reached the maximum elongation at break (26.21 %) which was 2.5 times of that of neat PLA (the elongation at break of neat PLA was 10.7 %). Meanwhile, with introducing 2 wt% DCP into PLA/NR blend, the maximum Charpy impact strength (7.36 kJ/m²) could be achieved which was 1.8 times of that of neat PLA (4.18 kJ/m²). Moreover, adding adequate amount of DCP could improve the processing properties of blends: the viscosity of PLA/NR blend decreased significantly and the lowest viscosity of the blends could be achieved when the DCP content was 0.5 wt%.