Processing and Characterization of Glycerol-Plasticized Soy Protein Plastics Reinforced with Citric Acid-Modified Starch Nanoparticles

Citric acid-modified starch nanoparticles with an average size of 82 nm were prepared through precipitation from gelatinized starch solution by ethanol and further modification with citric acid. When being incorporated in glycerol-plasticized soy protein plastics, citric acid-modified starch nanoparticles displayed dramatic reinforcing effect. The resulted nanocomposite plastics exhibited improvement in mechanical performance. Also, the water uptake decreased, indicating an increase of water resistance. The modified starch nanoparticles had a good compatibility with soy protein matrix. Possessing a relative hydrophobic surface, the filler would prefer to interact with protein-rich domains in glycerol-plasticized soy protein. The work provided a green approach of biodegradable materials based on naturally occurring biopolymers.     

Composite Film Based on Whey Protein Isolate/Pectin/CuO Nanoparticles/Betanin Pigments; Investigation of Physicochemical Properties

Journal of Polymers and the Environment - The aim of this work was to preparation of edible films based on whey protein isolate/pectin (WPIP) that containing betanin pigments (BP) and copper (I)...     

Optimization and Characterization of Bioactive Biocomposite Film Based on Orange Peel Incorporated with Gum Arabic Reinforced by Cr2O3 Nanoparticles

Journal of Polymers and the Environment - In this paper, the effect of adding gum arabic at levels of 0–5%, and chromium oxide nanoparticles (Cr2O3 NPs) at levels of 0–3%, were...     

Fabrication and Properties of Acid Treated Carbon Nanotubes Reinforced Soy Protein Nanocomposites

Acid treated multiwalled carbon nanotubes (MWNTs) were incorporated into glycerol plasticized soy protein to form MWNTs/soy protein nanocomposite plastics. The influence of the polar groups grafted on carbon nanotubes by acid treatment on the compatibility would be studied. The results showed that aggregation of carbon nanotubes was reduced by acid treatment and some polar groups were grafted on the nanotubes. The modified MWNTs were dispersed in soy protein matrix homogeneously and exhibited good compatibility with soy protein matrix. The crystalline structure of soy protein was not changed by MWNTs. The mechanical properties were dramatically enhanced through MWNTs incorporation due to the strong hydrogen bonding between them and the homogeneously dispersion of MWNTs in protein matrix, indicating the reinforcing effect of MWNTs in soy protein matrix. The water uptake was reduced and the thermal stability was enhanced by MWNTs incorporation.     

掺杂过渡金属离子的纳米二氧化钛光催化氧化对氯苯酚的研究

以掺杂过渡金属离子Fe^ 的纳米Ti02为光催化剂，以高压汞灯为光源，研究了对氯苯酚在水悬浮溶液中的降解，考察了对氯苯酚的初始浓度、气相氧浓度、催化剂投加量、光强对对氯苯酚光解速率的影响。通过试验发现，光强、气相氧浓度以及催化剂投加量是影响光催化氧化反应的关键因素。采用掺杂过渡金属粒子Fe^3 的纳米TiO2为光催化剂比采用纯纳米TiO2为光催化剂对氯苯酚降解率提高了近1．4倍。     

Development of Nanocomposite Films Based on Chitosan and Gelatin Loaded with Chitosan-Tripolyphosphate Nanoparticles: Antioxidant Potentials and Applications in Wound Healing

Journal of Polymers and the Environment - Recently, there is an increasing interest to prepare wound healing agents based on bio-polymers, due to their non-toxicity, biocompatibility and...     

Synthesis,Characterization and NH<Subscript>3</Subscript>/N<Subscript>2</Subscript> Gas Permeation Study of Nanocomposite Membranes

Carbon nanotubes have exceptional mechanical properties which make them very attractive for the development of composite membranes. In this research, NH₃/N₂ gas permeation behavior of flat sheet composite membranes was examined. The cellulose acetate-multiwalled carbon nanotubes composite membranes were synthesized using solution casting method. The morphology and dispersion of carbon nanotubes were observed through SEM. However, the composite membranes were also characterized using several analytical techniques such as X-ray diffraction analysis, tensile testing analysis, and thermal gravimetric analysis. Characterization of these membranes depicted that carboxylic group functionalized MWCNTs are extremely compatible with CA. The permeation experiments were performed with NH₃ and N₂ to explore the host–guest interaction of MWCNTs with chosen gases. The permeability of NH₃ was found pronounced compared to N₂. The NH₃/N₂ selectivity up to 90 was documented.     

CuO/Al2O3烟气脱硫技术及脱硫剂的研究进展

对CuO/Al2O3烟气脱硫技术的特点及其原理作了初步介绍，并翔实地阐述了国内外CuO/Al2O3脱硫剂的研究进展，提出了几点研究心得。     

Synthesis,Characterization and Nanocomposite Formation of Poly(glycerol succinate-co-maleate) with Nanocrystalline Cellulose

A novel biodegradable polymer based on glycerol, succinic anhydride and maleic anhydride, poly(glycerol succinate-co-maleate), poly(GlySAMA), was synthesized by melt polycondensation and tested as a matrix for composites with nanocrystalline cellulose. This glycerol-based polymer is thermally stable as a consequence of its targeted cross-linked structure. To broaden its range of properties, it was specifically formulated with nanocrystalline cellulose (NCC) at concentrations of 1, 2 and 4 wt%, and showed improved mechanical properties with NCC. Specifically, the effect of reinforcement on mechanical properties, thermal stability, structure, and biodegradability was evaluated, respectively, by tensile tests and thermogravimetric analyses, X-ray diffraction and respirometry. The neat poly(GlySAMA) polymer proved flexible, exhibiting an elongation-to-break of 8.8 % while the addition of nanowhiskers (at 4 wt%) caused tensile strength and Young’s modulus to increase, 20 and 40 %, respectively. Stiffness improved without significantly decreasing thermal stability as measured by thermogravimetric analysis. Biodegradation tests indicated that all samples were degradable but NCC reduced the rate of biodegradation.     

Citric Acid and Vitamin C as Coupling Agents for the Surface Coating of ZrO<Subscript>2</Subscript> Nanoparticles and Their Behavior on the Optical,Mechanical, and Thermal Properties of Poly(vinyl alcohol) Nanocomposite Films

A series of bio-nanocomposites (BNC)s were fabricated through solution casting method. At first, the surfaces of ZrO₂ NPs were functionalized with citric acid and Vitamin C as green modifier agents. Then, PVA as polymer matrix was embedded with different contents (4, 8 and 12 wt%) of modified ZrO₂ (m-ZrO₂) NPs with the aim of ultrasonic irradiation process. The resulting BNCs were studied by various techniques. Thermal stability of obtained BNCs was enhanced after NPs’ addition to the PVA matrix. Optical activity of these new BNCs makes them potential candidate for UV shielding material. Lastly, the tensile strengths of the BNCs were increased in comparison to the pure PVA.     

Nanocomposite Film Based on Gluten Modified with Heracleum persicum Essence/MgO/Polypyrrole: Investigation of Physicochemical and Electrical Properties

In this study, the wheat gluten film was prepared. Heracleum persicum essence, magnesium oxide nanoparticles and polypyrrole were used to modify the structure of the wheat gluten film. Physicochemical properties of the prepared films such as thickness, solubility, moisture absorption ability, antioxidant properties, and electrical conductivity of the films were investigated. Also, the mechanical, structural and thermal properties of the films were investigated by techniques such as SEM, FTIR, XRD, TGA, DTA and tissue analysis. SEM images showed that the essence and polypyrrole strengthened the gluten film structure and made it more resistant to the passage of gases. FTIR spectra confirmed the electrostatic interactions between gluten and essence and polypyrrole. XRD spectra showed the amorphous structure of gluten film and its composites. The results of thermal analysis showed that polypyrrole greatly increased the thermal resistance of the film and the nanoparticles had little effect on the thermal resistance. Thickness, solubility, moisture content and ability to absorb moisture were further affected by the essential oil. The antioxidant and electrical conductivity of the film was greatly increased in the presence of all three additives of essence, magnesium oxide nanoparticles and polypyrrole. The gluten–essence–MgO–PPy (Glu–E–MgO–PPy) composite film had the most antioxidant properties. Glu–E–MgO–PPy film with important electrical conductivity and antioxidant properties has the potential to be used as an active and intelligent film in the packaging of perishable food products.

     

Fabrication and Characterization of Biodegradable Composite Films Made of Using Poly(caprolactone) Reinforced with Chitosan

Chitosan was dissolved in 2?% aqueous acetic acid solution and the films were prepared by solution casting. Values of tensile strength (TS), tensile modulus (TM), elongation at break (Eb?%) and water vapor permeability (WVP) of the chitosan films were found to be 30?MPa, 450?MPa, 8?% and 4.7?g?mm/m²?day?kPa, respectively. Poly(caprolactone) (PCL) films were prepared from its granules by compression molding and the values of TS, TM, Eb and WVP were 14?MPa, 220?MPa, 70?% and 1.54?g?mm/m²?day?kPa, respectively. PCL was reinforced with chitosan films, and composite films were prepared by compression molding. Amount of chitosan in the composite films varied from 10 to 50?% (w/w). It was found that with the incorporation of chitosan films in PCL, both the values of TS and TM of composite films increased significantly. The highest mechanical properties were found at 50?% (w/w) of chitosan content. The Oxygen transmission rate (OTR) of composite film was found to decrease significantly than PCL films. Thermal properties of the composite were also improved as compared to PCL. The water uptake test of the composite also showed promising results with a good stability of composite films. The interface of the composite was investigated by scanning electron microscopy and showed good interfacial adhesion between PCL and chitosan films.     

Effect of the Fe2O3/TiO2 Nanoparticles on the Structural,Mechanical, Electrical Properties and Antibacterial Activity of the Biodegradable Chitosan/Polyvinyl Alcohol Blend for Food Packaging

Journal of Polymers and the Environment - As the request for ready-made food grows, it’s more important than ever to develop effective antimicrobial food packaging materials to assure...     

Influence of TiO<Subscript>2</Subscript> Nanoparticles on the Crystallization Behaviour and Tensile Properties of Biodegradable PLA and PCL Nanocomposites

This paper investigated the influence of TiO₂ nanoparticles on the morphologies, as well as crystallization behaviour and kinetics, of neat PLA and PCL, and of these polymers in different PLA/PCL blends. We used transmission electron microscopy to evaluate the morphologies of the systems, while the crystallization behaviour and kinetics were investigated through differential scanning calorimetry (DSC). In addition to standard and modulated (StepScan) DSC analyses, the self-nucleation temperatures of neat PCL and PCL in the different nanocomposites were determined, followed by a self-nucleation and annealing thermal fractionation analysis of PCL crystallization and an Avrami isothermal kinetic analysis of PCL crystallization and PLA cold crystallization. We found that the nanoparticles were well dispersed, but only in the PLA phase of the blends, with only a few on the interface or in the PCL phase. They did nucleate and accelerate, and influence the mechanism of, the PCL crystallization in neat PCL, but had little influence on PCL crystallization in the blends. They strongly influenced the rate of cold crystallization of PLA, but had little influence on this parameter in the blends. The tensile properties were also determined, and changes in these properties could be related to the morphologies of the systems.     

Characterization of Super Paramagnetic Nanoparticles Coated with a Biocompatible Polymer Produced by Dextransucrase from <Emphasis Type="Italic">Weissella cibaria</Emphasis> JAG8

Magnetic nanoparticles (MNPs) synthesised by chemical co-precipitation method was subjected to dextran coating by sonication method. The dextran was enzymatically synthesised by extracellular dextransucrase isolated from Weissella cibaria JAG8. The crystalline nature of MNPs and dextran coated MNPs were confirmed by X-ray diffraction studies with average particle size of 25 nm, which was confirmed further by high resolution transmission electron microscopy. The surface morphology of MNPs and dextran coated MNPs were monitored by scanning electron microscopy studies. The vibrating sample magnetometer investigation displayed the super paramagnetic nature of MNPs and dextran coated MNPs. FT-IR analysis of MNPs and dextran coated MNPs, displayed characteristic band of Fe–O bond at 582 cm^?1. Thermo-gravimetric analysis of MNPs and dextran coated MNPs (1:1) ratio displayed a weight loss of 15 and 18 %, which clearly indicated 3.0 % of dextran was coated on to the MNPs. The elemental composition study by scanning electron microscopy confirmed the association of dextran with MNPs. The in vitro effect of MNPs and dextran coated MNPs was performed on human colon cancer (HT-29) cell lines and the results showed that dextran coated: MNPs (2:1) displayed good biocompatibility results over dextran coated: MNPs (1:1) and un-coated MNPs.     

A New Ozonated Cassava Film with the Addition of Cellulose Nanofibres: Production and Characterization of Mechanical,Barrier and Functional Properties

Journal of Polymers and the Environment - In this study cassava starch modified by ozone technology and cellulose nanofibres were used to produce films. These nanocomposites were produced by...     

Preparation,Characterization, and Rapid Adsorption of Hg<Superscript>2+</Superscript> on Nanoscale Aramid-based Adsorbent

A series of nanaoscale aramid-based adsorbents were prepared by the functionalization of poly (p-phenylene terephthalamide) (PPTA) with different content of ethylenediamine (EDA). Their structures were characterized by field emission scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and elemental analysis. Metal ions, including Hg²⁺, Pb²⁺, Ag⁺, Cu²⁺, Cd²⁺, and Ni²⁺ were chosen as the models to explore the binding behaviors of PPTA–ECH–EDA in aqueous medium. Results showed that PPTA–ECH–EDA exhibited higher adsorption capacity for Hg²⁺ due to their nanoscale structures. In particular, the adsorption rate was so high that equilibrium was achieved within 15 min for Hg²⁺. The adsorption of Hg²⁺ on PPTA–ECH–EDA followed the pseudo second-order model well. Langmuir and Freundlich models were employed to fit the isothermal adsorption, and the results revealed that Freundlich isotherm was a better model to predict the experimental data. The adsorption mechanism was revealed by X-ray photoelectron spectroscopy. It is preconceived that PPTA–ECH–EDA could be used as an effective adsorbent for fast removal of heavy ions from wastewater.     

Synthesis, Characterization, and Hydrolytic Degradation of Copolymers of 2-Methylene-1,3-dioxepane with Ethylene and with Styrene

2-Methylene-1,3-dioxepane (MDP) was copolymerized with ethylene (E) at a pressure of approximately 1000 psi and a temperature of approximately 70°C with AIBN as the free radical initiator. The copolymers obtained, poly(MDP-co-E), were characterized by elemental analysis, IR, ¹H-NMR and ¹³C-NMR spectroscopy, DSC, and GPC. The copolymers contained 2–15 mol% ester units. MDP was also copolymerized with styrene (S) at 120°C with di-t-butyl peroxide as the initiator to prepare the copolymer, poly(MDP-co-S). The number-average molecular weights of both types of copolymers were in the range of 6000 to 11,000, and the weight-average molecular weights were in the range of 9000 to 17,000. The melting temperatures of poly(MDP-co-E) decreased with increasing ester unit content in the copolymer. For the MDP-S copolymers, the glass transition temperatures decreased with increasing ester unit content. Both poly(MDP-co-E) and poly(MDP-co-S) were degraded by methanolysis, and their molecular weights decreased by the expected amounts based on the ester unit content.