Modification of Aliphatic Polyesters and Their Reactive Blends with Starch

Modified polycaprolactone was synthesized by melt reaction of PCL and reactive monomers such as glycidyl methacrylate (GMA) and maleic anhydride (MAH) in the presence of benzoyl peroxide in Brabender mixer. MAH showed a different grafting phenomenon compared to GMA. The reaction mechanism was discussed with different reactive monomers. Reactive blends of the PCL-g-GMA and the gelatinized starch with glycerin were prepared and their mechanical properties and biodegradabilities were investigated. Reactive blends of PCL-g-GMA and starch showed well-dispersed starch domain in the matrix and better mechanical strength than the unmodified PCL/starch blend. However, the reaction between PCL-g-GMA and starch induced a crosslinking during the reactive blending and this crosslinking in the blend lowered the biodegradation of the blend during the composting test. The biodegradability was investigated by the weight loss and surface morphology change of the blend in the composting medium.     

Effect of Curing Temperature on Mechanical Properties of Bio-phenolic/Epoxy Polymer Blends

Journal of Polymers and the Environment - Nowadays, researchers continue studies for alternative materials to replace the redundant petroleum-based products. The combination of various polymer...     

Grafting of Glycidyl Methacrylate onto Poly(lactide) and Properties of PLA/Starch Blends Compatibilized by the Grafted Copolymer

Poly(lactide)-graft-glycidyl methacrylate (PLA-g-GMA) copolymer was prepared by grafting GMA onto PLA in a batch mixer using benzoyl peroxide as an initiator. The graft content was determined with the ¹H-NMR spectroscopy by calculating the relative area of the characteristic peaks of PLA and GMA. The result shows that the graft content increases from 1.8 to 11.0 wt% as the GMA concentration in the feed varies from 5 to 20 wt%. The PLA/starch blends were prepared by the PLA-g-GMA copolymer as a compatibilizer, and the structure and properties of PLA/starch blends with or without the PLA-g-GMA copolymer were characterized by SEM, DSC, tensile test and medium resistance test. The result shows that the PLA/starch blends without the PLA-g-GMA copolymer show a poor interfacial adhesion and the starch granules are clearly observed, nevertheless the starch granules are better dispersed and covered by PLA when the PLA-g-GMA copolymer as a compatibilizer. The mechanical properties of the PLA/starch blends with the PLA-g-GMA copolymer are obviously improved, such as tensile strength at break increasing from 18.6 ± 3.8 MPa to 29.3 ± 5.8 MPa, tensile modulus from 510 ± 62 MPa to 901 ± 62 MPa and elongation at break from 1.8 ± 0.4 % to 3.4 ± 0.6 %, respectively, for without the PLA-g-GMA copolymer. In addition, the medium resistance of PLA/starch blends with the PLA-g-GMA copolymer was much better than PLA/starch blends.     

Preparation of Chitin/Cellulose Films Compatibilized with Polymeric Ionic Liquids

This paper reports the preparation of chitin/cellulose films compatibilized with polymeric ionic liquids. In-situ (co)polymerization of polymerizable ionic liquids, 1-(3-methacryloyloxypropyl)-3-vinylimidazolium bromide (1) and 1-methyl-3-vinylbenzylimidazolium chloride (3), was carried out in the presence of a radical initiator, AIBN, in the chitin/cellulose solution with ionic liquid solvents (1-butyl-3-methylimidazolium acetate and chloride, BMIMOAc and BMIMCl, respectively), followed by the appropriate procedure to give the desired films. The presence of the polymeric ionic liquid in the film was confirmed by the IR measurement. The powder X-ray diffraction analysis suggested that crystalline structures of the polysaccharides were largely disrupted in the film, as same as that of a chitin/cellulose film prepared by the AMIMOAc/BMIMCl system. These results were different from the XRD result of a chitin/cellulose film prepared by the 1-allyl-3-methylimidazolium bromide/BMIMCl system reported in our previous study, in which some crystalline structures were still remained in the film. Furthermore, the mechanical properties of the present films were evaluated by tensile testing, which were affected by the molar ratios of the polymeric ionic liquids to the polysaccharides and the compositional ratios of the two units 1 and 3.     

The Investigation of the Toughening Mechanism of PHBV/PBAT with a Novel Hyperbranched Ethylenediamine Triazine Polymer Based Modifier: The Formation of the Transition Layer and the Microcrosslinking Structure

A new type of designed hyperbranched ethylenediamine trazine polymer (HBETP) is successfully synthesized and characterized based upon NMR and GPC. The prepared HBETP is used to modify the poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV)/poly(butylene adipate-co-terephthalate) (PBAT) blends. The effect of HBETP on the microstructure, mechanical properties and thermal properties of the blends is studied. The results indicate that upon addition of 1.0 wt% of HBETP, the impact strength of the PHBV/PBAT blends is increased by 47.1%; ?T_g of the blends decreases from 53.2 to 49.9 °C. These results, together with the morphology analysis of the fractured surface of the blends, conclude the formation of the transition layer between PHBV and PBAT. Also, the XRD result shows that the addition of HBETP can limit the growth of the PHBV crystals and causes the decrease of both the crystallinity and the grain crystalline size. The DSC result demonstrates that the addition of HBETP mainly affects the crystallization of the HB-HV binary eutectic region within PHBV. The mechanism of PHBV/PBAT toughening is due to the formation of the strong physical hydrogen bonding and the chemical micro-crosslinking between HBETP and PHBV/PBAT, which is proposed based on XPS characterization.     

Preparation and Characterization of Biodegradable Blend Membranes of PBS/CA

Asymmetric membranes of cellulose acetate/poly (butylene succinate) were prepared using immersion precipitation technique. The blended membranes were characterized by contact angle, scanning electron microscopy, thermogravimetric analysis, degradation test in compost and dynamic test of raisin wastewater treatment. Results demonstrated that hydrophilicity of cellulose acetate was enhanced by addition of poly (butylene succinate) up to 50 %. Furthermore, polymeric composition affects cross sectional structure of the membranes by controlling formation of macrovoids. Addition of poly (butylene succinate) improved the membranes thermal stability and obviously their degradation in compost. The prepared membranes were able to reject the wastewater pollutants properly.     

Biodegradability of a Selected Range of Polymers and Polymer Blends and Standard Methods for Assessment of Biodegradation

Synthetic polymers are important to the packaging industry but their use raises aesthetic and environmental concerns, particularly with regard to solid waste accumulation problems and the threat to wildlife. Some concerns are addressed by attention to problems associated with source reduction, incineration, recycling and landfill. Others are addressed by the development of new biodegradable polymers either alone or in blends. Materials used for biodegradable polymers include various forms of starch and products derived from it, biopolyesters and some synthetic polymers. Starch is rapidly metabolised and is an excellent base material for polymer blends or for infill of more environmentally inert polymers where it is metabolised to leave less residual polymer on biodegradation. This should help to improve the environmental impact of waste disposal. A number of standard methods have been developed to estimate the extent of biodegradability of polymers under various conditions and with a variety of organisms. They tend to be used mainly in the countries where they were developed but there is much overlap between the standards of different countries and wide scope for development of consistent and international standards.     

Effect of the Pretreatment with UV and Gamma Radiations on the Modification of Plywood Surface by Photocuring with Epoxy Acrylate

In order to further improve the physical properties of plywood surface that was pretreated with UV and Gamma radiation at different radiation intensities before photocuring. After pretreatment with radiation the plywood surface was coated with different prepared formulations containing epoxyacrylate (EA-1020) as an oligomer, difunctional monomers such as tripropylene glycol diacrylate (TPGDA), 2-hexadioldiacrylate (HDDA), Ethylene Glycol dimethacrylate (EGDMA) and trifunctional monomer trimethyl propen triacrylate (TMPTA) with photoinitiator Darocur 1664. Thin polymer films were prepared on glass plate with these formulated solutions and cured under UV radiation. Pendulum hardness (PH) and gel content of the film were studied for selecting the formulations as top coat and as base coat. The polished plywood surface was coated with selected formulation and cured under UV radiation. Various rheological properties of UV cured plywood surface such as pendulum hardness, scratch hardness, microgloss, adhesion strength, percentage chipped off area and abrasion resistance were studied.     

Processing and Properties of Biopolymer/Polyhydroxyalkanoates Blends

In this paper, the processability and the performance of a biodegradable polymer, Mater-Bi, and of its blends with either a sample of poly (hydroxy alkanoates) (PHA) or with bacterial biomass containing PHAs were compared. Adding PHA or directly the biomass containing it allows improving the processability of the matrix. Moreover, the mechanical behaviour of the systems was compared considering two different preparation methods, namely compression and injection moulding. The injection moulded samples show poorer mechanical performances than those of the compression moulded systems. The impact strength significantly improves when PHA is added while it reduces when bacterial biomass is used instead. In this latter case this was likely due to the easier propagation of micro-cracks during the impact tests.     

The Effect of CTBN Concentrations on the Kinetic Parameters of Decomposition of Blends of Epoxy Resins Modified with Carboxyl-Terminated Liquid Copolymer

Diglycidyl ether of bisphenol—A (DGEBA)—based epoxy resin was blended in the ratio of 3:1 (weight basis) with cycloaliphatic epoxy (CAE) resin. The prepared blend sample was further blended with different weight percentages of carboxyl-terminated butadiene acrylonitrile copolymer (CTBN) ranging between 0 and 25 wt% with an interval of 5 wt% and cured with stiochiometric amounts of 4, 4’- diamino diphenyl sulphone (DDS) cure agent. Structural changes during blending were studied by Fourier-transform infra-red (FTIR) spectroscopic analysis. The kinetic parameters, viz., order of decomposition reaction (n), activation energy (E), pre-exponential factor (Z) and rate decomposition constant (k), for the decomposition of the samples were calculated by applying Coats-Redfern equation over thermogravimetric (TG) data. The degradation of each sample followed second-order degradation kinetics, which was calculated by Coats-Redfern equation using best-fit analysis. This was further confirmed by linear regression analysis. The validity of data was checked by t-test statistical analysis. Further, the blend sample had higher initial degradation temperature and activation energy than its respective pure epoxy resin indicating that the CTBN acted as thermal stabilizer for epoxy resin which improved the thermal stability.     

Biodegradation of LDPE/Modified Starch Blends Sterilized with Gamma Radiation

Blends of LDPE/modified starch were prepared, sterilized by gamma radiation and investigated with respect to their microbial degradation by a mixture of fungal strains in liquid medium after 90 days, was analyzed by carbon dioxide (CO₂) production (Sturm test). Biodegradation of blends was evaluated by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction; mechanical testing, scanning electron microscopy (SEM). The biodegradation of LDPE/modified starch blends was attributed to microbiological attack, with alterations in the chemical structure of the blend with an increase in the carbonyl and vinyl indices and the appearance of new crystalline symmetry generating a crystalline domain not existing before in the blend and decrease in the mechanical properties.     

Controlling the Behaviors of Biodegradable/Bioabsorbable Polymers with Cyclodextrins

The cyclic six, seven, and eight-membered oligosaccharides -, -, and -cyclodextrins (CDs) can serve as hosts for a variety of polymer guests to form crystalline inclusion compounds (ICs), wherein the guest polymers are included in the continuous narrow channels (0.5–1.0 nm in diameter) formed by the host CD stacks. Polymers included as guests in CD-ICs are highly extended and segregated from neighboring chains by the walls of the host CD bracelets. As a consequence, when polymer-CD-ICs are treated with solvents for CDs that are non-solvents for the included polymers or with amylase enzymes, the CDs are removed and the guest polymers are coalesced into bulk samples whose structures, morphologies, and even chain conformations are different from those achieved by consolidation from their randomly coiling, entangled solutions and melts. Often these CD-IC coalesced and consequently reorganized polymer samples exhibit properties that are distinct from their normally processed bulk samples. Here we describe the CD-IC processing of several biodegradable/bioabsorbable homopolymers, copolymers, and blends made from poly (L-lactic acid), poly (-caprolactone), and poly (-hydroxybutyrate)s, with special emphasis placed on their improved and controllable properties. For example, the phase segregation and consequent crystallinities of their normally incompatible homopolymer blends and their block copolymers may be controlled and thus improved. In addition, co-inclusion of small molecule guests, such as drugs or anti-bacterials, in their common CD-ICs, and subsequent coalescence, yields well-mixed blends of these biodegradable/bioabsorbable polymers and the small molecule co-guests, which may lead, for example, to the improved delivery of drugs.     

Influence of reprocessing cycles on mechanical and antibacterial performances of hygienic in situ compatibilized PBS/PLA blends doped with HPQM

Journal of Material Cycles and Waste Management - A spontaneous combination of hygienic in situ compatibilized polybutylene succinate/polylactic acids (PBS/PLA) was formulated through the addition...     

Biodegradable Blends with Potential Use in Packaging: A Comparison of PLA/Chitosan and PLA/Cellulose Acetate Films

Poly(lactic acid) (PLA) is a biodegradable polymer that exhibits high elastic modulus, high mechanical strength, and feasible processability. However, high cost and fragility hinder the application of PLA in food packaging. Therefore, this study aimed to develop flexible PLA/acetate and PLA/chitosan films with improved thermal and mechanical properties without the addition of a plasticizer and additive to yield extruder compositions with melt temperatures above those of acetate and chitosan. PLA blends with 10, 20, and 30 wt% of chitosan or cellulose acetate were processed in a twin-screw extruder, and grain pellets were then pressed to form films. PLA/acetate films showed an increase of 30 °C in initial degradation temperature and an increase of 3.9 % in elongation at break. On the other hand, PLA/chitosan films showed improvements in mechanical properties as an increase of 4.7 % in elongation at break. PLA/chitosan film which presented the greatest increase in elongation at break proved to be the best candidate for application in packaging.     

Mechanical Properties and Morphology of Polypropylene/Poly(ethylene-co-octene) Blends

The polypropylene (PP)/poly(ethylene-co-octene) (POE) blends was prepared by means of a twin screw extruder in a range of temperature from 185 to 195 °C. The mechanical properties including tensile, flexural and impact of the PP/POE blends were measured at room temperature to identify the effect of the POE content on the mechanical properties. It was found that the Young’s modulus, tensile strength and tensile elongation at break decreased nonlinearly with increasing the POE weight fraction. While the V-notched and unnotched impact fracture strength increased nonlinearly with an increase of the POE weight fraction. The flexural modulus and strength decreased roughly linearly with increasing the POE weight fraction. Furthermore, the impact fracture surface of the blends was observed by using a scanning electronic microscope and the toughening mechanisms were discussed.     

Mechanical and Dynamic Mechanical Analysis of Woven Banana/Epoxy Composite

In this work, three types of woven (Plain, twill and Basket) composites are made of banana fibers/epoxy resin using hand-layup method. Mechanical properties (tensile, flexural and impact) of three types of woven composites are compared to evaluate the effect of weaving architecture on the properties. Dynamic Mechanical Analysis is carried out to analyse the visco-elastic behavior of the composite. Dynamic Mechanical Analysis is carried out in the temperature range of 40?C140?°C at 0.1,1,10?Hz frequencies. Scanning Electron Microscopic analysis is carried out to investigate the fracture behaviour of the composite. From the investigation it is found that plain type of woven composite has better mechanical and dynamic mechanical behaviour.     

Melt Flow Behavior and Processability of Polylactic Acid/Polystyrene (PLA/PS) Polymer Blends

The present investigation dealt with the flow behavior and processability of polylactic acid/polystyrene (PLA/PS) polymer blends using a capillary rheometer. For this purpose, PLA/PS blends with different ratios of the concentrations were prepared using a single screw extruder. The shear viscosity, shear stress, shear rate, power-law index, viscous activation energy at a constant shear stress, and elongational stress were determined. PLA/PS blends exhibited a typical shear-thinning behavior over the entire range of shear rates tested, and the viscosity values of the blends would tend to decrease with increasing amount of PLA. In addition, the polymer blend of 70 % PLA and 30 % PS was found to be relatively less sensitive to the processing temperature, implying that the extrusion process was more desirable for fabrication of PLA/PS polymer blend than the injection process.     

Natural Weathering of Polypropylene and Waste Tire Dust (PP/WTD) Blends

Three series of polypropylene and waste tire dust (PP/WTD) blends using three different WTD sizes were prepared, compression-molded and cut into dumbbells. The specimens were exposed to natural weathering in the northern part of Malaysia for a period of 6 months. The results show that at the same blend composition, blends with fine WTD size exhibit higher mechanical properties than that of blends with coarse WTD after exposure to natural weathering. Regardless of WTD size, the retention of tensile strength and elongation at break, E_b increases with the increase in WTD content. From the exposed surface morphology, it is apparent that the blends with fine WTD and WTD-rich blends were able to withstand weathering better than blends with coarse WTD and PP-rich blends. The DSC thermograms suggest that the overall drop in melting temperature (T_m) of the exposed blends decreases as the WTD content increases.     

Crystal and Thermal Properties of PLLA/PDLA Blends Synthesized by Direct Melt Polycondensation

We herein report the effects of the component ratio and method of blending on the synthesis of stereocomplex poly(lactic acid) (SC-PLA) based on poly(l-lactic acid) (PLLA) and poly(d-lactic acid) (PDLA) prepolymers. PLLA and PDLA were prepared by direct melt polycondensation of lactic acid (DMP). Combined with the dual catalyst system, PLA prepolymers with M_w more than 20,000 were prepared by DMP. PLLA was mixed by powder blending or melt blended with PDLA. It is revealed that melt-point and spherulite growth rate of SC-PLA is strongly dependent on the perfection of SC structure. The melt point of PLA can be increased by nearly 50 °C because of the particular strong intermolecular interaction between PLLA and PDLA chains. Solid-state polycondensation (SSP) is an efficient method to increase the molecular weight of SC-PLA, but it can have a negative effect on the regularity of linear chains of SC-PLA. Thermogravimetry analyzer (TGA) results show that SC structure cannot cause the delay reaction on the thermal degradation of PLA.