铋电极差分脉冲伏安法测定水中痕量2,4-二硝基苯肼

以自制铋电极作为工作电极,建立了铋电极差分脉冲伏安法测定2,4-二硝基苯肼的分析方法。实验结果表明：以0.1 mol/L NaOH+0.1 mol/L KCl混合溶液（pH=13.0）配制测定底液,在扫描速率为100 mV/s的条件下,2,4-二硝基苯肼于-0.53 V处产生灵敏的氧化峰;在2,4-二硝基苯肼浓度为3.0×10-8~1.0×10-5 mol/L范围内,空白和试样的氧化峰电流强度差值与对应2,4-二硝基苯肼浓度的对数呈良好的线性关系,检出限达8.37×10-9 mol/L;将该方法应用于工业废水中痕量2,4-二硝基苯肼的检测,回收率为95.6%~103.1%,相对标准偏差小于3%。     

β-环糊精增敏催化动力学光度法测定亚硝酸根

在磷酸介质中利用亚硝酸根催化条件下溴酸钾氧化甲基红的褪色反应,建立了β-环糊精（β-CD）增敏催化动力学光度法,对亚硝酸根进行测定。该方法最佳反应条件为：0.05 mol/L甲基红溶液加入量8.0%（φ,下同）,0.1 mol/L溴酸钾溶液加入量12.0%,1.0 mol/L稀磷酸加入量12.0%,0.15 mol/L β-CD溶液加入量16.0%,反应温度40 ℃,反应时间15 min。亚硝酸根测定的线性范围为8.0×10^-6~6.0×10^-4 g/L,线性回归方程的相关系数为0.996 6,检出限为4.0×10^-7 g/L。亚硝酸根的加标回收率为99.0%~102.0%,水样测定结果的相对标准偏差为2.4%~3.2%。加入β-CD后测定亚硝酸根的灵敏度增加了2.5倍。     

Ti_5O_9-Ti_4O_7电极电化学处理2,4,6-三硝基苯酚废水

采用压片-烧结法制备了Ti5O9-Ti4O7电极,采用XRD和SEM技术对Ti5O9-Ti4O7电极进行了表征。以自制的Ti5O9-Ti4O7电极为阳极,电解处理含2,4,6-三硝基苯酚(TNP)的模拟废水,考察了电流密度、电解质质量浓度、废水p H、废水温度和反应时间等因素对废水COD去除率和TNP降解率的影响。表征结果显示:该电极的主要成分为Ti5O9,并含有部分Ti4O7;该电极的比表面积较大。Ti5O9-Ti4O7电极电解处理含TNP废水的最佳实验条件为:电流密度20 m A/cm2、电解质Na2SO4质量浓度6.0 g/L、废水p H为7、废水温度30℃。在此最佳条件下电解反应180 min后,COD去除率为90.6%,TNP降解率为93.9%,表明Ti5O9-Ti4O7电极具有较高的催化能力和电流效率。     

亚铁氰化铜的制备及其对铯的吸附

以亚铁氰化钠和硝酸铜为原料,采用水热合成法制备出亚铁氰化铜(CuFC)吸附剂,对其进行了表征,并考察了CuFC对模拟放射性废水中铯的吸附性能。表征结果显示:产物的分子式为Cu2Fe(CN)6·7H2O,外观为具有清晰几何形状的颗粒物,粒径约为30 nm。25℃下的静态吸附实验结果表明:当初始铯质量浓度为98.01μg/L、CuFC加入量为0.08 g/L、吸附时间为90 min时,达到吸附平衡,铯的去污系数达到1.13×104;用拟二级动力学模型可准确描述CuFC对铯的吸附过程,相关系数为1.000 0;吸附等温线符合Freundlich等温吸附模型。     

离子液体改性活性炭对芳香烃的吸附性能

采用浸渍法和嫁接法分别将1-丁基-3-甲基咪唑双三氟甲烷磺酰亚胺盐（[Bmim]TFSI）、丙基三辛基鏻四氟硼酸盐（[P（C₃H₇）（C₈H₁₇）₃]BF₄）和丙基三辛基鏻双三氟甲烷磺酰亚胺盐（[P（C₃H₇）（C₈H₁₇）₃]TFSI）负载于活性炭上。对产物进行了热重和孔结构分析,并以气相甲苯和二甲苯为代表物,研究了其对芳香烃的静态和动态吸附性能。研究结果表明：活性炭经离子液体改性后,能显著提高其对芳香烃的吸附性能;其中 [P（C₃H₇）（C₈H₁₇）₃]TFSI和[P（C₃H₇）（C₈H₁₇）₃]BF₄）浸渍改性活性炭的甲苯静态吸附量较大,分别为782 mg/g和777 mg/g （25 ℃,0.1 MPa）;[P（C₃H₇）（C₈H₁₇）₃]BF₄浸渍改性活性炭对于3种二甲苯异构体的吸附量最大,且排序依次为邻二甲苯>间二甲苯>对二甲苯。吸附动力学研究表明,在较高的甲苯初始浓度和较低的气体流量下,[P（C₃H₇）（C₈H₁₇）₃]TFSI浸渍改性活性炭具有更好的吸附性能。     

环氧氯丙烷生产废水的资源化处理技术

采用催化湿式过氧化物氧化法（CWPO）处理环氧氯丙烷生产废水,考察了反应温度、反应时间、反应pH、双氧水和FeSO₄#x000b7;7H₂O加入量及投加方式等因素对TOC去除率的影响。实验结果表明：CWPO工艺适宜的反应条件为反应温度90℃,反应pH2.0~3.0,FeSO₄#x000b7;7H₂O₂加入量7.50~8.75g/L,双氧水加入量75mL/L,反应时间100min;双氧水和Fe²⁺分多次投加时的TOC去除效果明显优于一次性投加;优化条件下,环氧氯丙烷废水经CWPO工艺处理后,TOC由1790mg/L降至138mg/L,符合氯碱厂隔膜电解槽进槽盐水的要求,可以资源化利用。     

pH对厌氧氨氧化反应脱氮效能的影响

采用具有恒定pH功能的SBR接种厌氧氨氧化颗粒污泥,研究了pH对厌氧氨氧化菌脱氮效能的影响。实验结果表明:在进水ρ(氨氮)和ρ(亚硝酸盐氮)分别为58.00 mg/L和79.28 mg/L、TN容积负荷为0.82 kg/(m3·d)、不控制反应pH的条件下,随着反应的进行,pH不断升高,当pH=8.02时,菌种的去除效能最高;在进水ρ(氨氮)和ρ(亚硝酸盐氮)分别为120.00 mg/L和159.33 mg/L、TN容积负荷为1.62 kg/(m3·d)、恒定反应pH为8.00的条件下,反应4.0 h时的容积基质氮去除速率(NRR)达到1.42 kg/(m3·d),氨氮去除率达98.39%,亚硝酸盐氮去除率达99.48%;拟合曲线推导的最适pH的理论值为7.85,反应4.0 h时的NRR理论最大值达1.52 kg/(m3·d)。     

催化动力学光度法测定工业废水中的Cr（Ⅵ）

采用β-环糊精作为H₂O₂氧化茜素红褪色反应的增敏剂,建立了催化动力学光度法测定工业废水中Cr（Ⅵ）的新方法。该方法最佳反应条件为：反应体系总体积25 mL,0.1 mol/L的H₂SO₄溶液加入量2.0 mL,1.0×10^-3 mol/L茜素红溶液加入量1.5 mL,30%的H₂O₂溶液加入量4.0 mL,100 g/L的β-环糊精溶液加入量3.0 mL。在最大吸收波长554 nm处测定反应前后溶液的吸光度,Cr（Ⅵ）的质量浓度与吸光度差值（ΔA）在4.0×10^-4~5.4×10^-2 mg/L范围内符合比尔定律,线性回归方程为：ΔA=18.52ρ+ 0.018,相关系数为0.996 6,检出限为3.5×10^-4 mg/L,加标回收率为99.46%~101.3%,6次测定的相对标准偏差小于等于2.4%。该法的测定结果与GB/T 7467-1987中的二苯碳酰二肼分光光度法相近。     

Repartition of PCDD and PCDF in the emissions of municipal solid waste incinerators between the particulate and volatile phases

The present paper refers to the results of a research project on the polychlorinated dibenzyil-p-dioxin (PCDD) and polychlorinated dibenzofurans repartition in particulate and volatile phase in emissions from municipal solid waste incinerators. The distribution of such micropollutants between the different phases is analyzed in terms of absolute weights and in terms of 2, 3, 7, 8 TCDD Equivalents. This paper shows that more than half of the total content of PCDD/Fs emitted are adsorbed in the fly ash, with the remaining part in the volatile phase. Such repartition is inverted if the PCDD/Fs are expressed in terms of 2, 3, 7, 8 TCDD Equivalent.     

混凝—Fenton法深度处理维生素B12废水

采用混凝—Fenton法深度处理维生素B12废水,考察各操作参数对COD和色度去除效果的影响。实验结果表明：当混凝pH 4.5、聚合硫酸铁加入量300 mg/L、氧化pH 4.0、H2O2加入量420 mg/L、FeSO4?7H2O加入量334 mg/L、Fenton反应时间3 h时,混凝—Fenton法对维生素B12废水的深度处理效果较好,总COD和总色度的去除率分别为62.1%和90.0%;与Fenton法相比,混凝—Fenton法COD和色度去除率的提高率分别为17.4%和13.8%,且药剂成本降低了21.6%。     

Transportation fuel production by combination of LDPE thermal cracking and catalytic hydroreforming

Fuel production from plastics is a promising way to reduce landfilling rates while obtaining valuable products. The usage of Ni-supported hierarchical Beta zeolite (h-Beta) for the hydroreforming of the oils coming from LDPE thermal cracking has proved to produce high selectivities to gasoline and diesel fuels (>80%). In the present work, the effect of the Ni loading on Ni/h-Beta is investigated in the hydroreforming of the oils form LDPE thermal cracking. h-Beta samples were impregnated with Ni nitrate, calcined and reduced in H₂ up to 550 °C to achieve different Ni contents: 1.5%, 4%, 7% and 10%. Larger and more easily reducible metal particles were obtained on Ni 7%/h-Beta and Ni 10%/h-Beta. Hydroreforming tests were carried out in autoclave reactor at 310 °C, under 20 bar H₂, for 45 min. Ni content progressively increased the amount of gases at the expenses of diesel fractions, while gasoline remained approximately constant about 52–54%. Maximum selectivity to automotive fuels (～81%) was obtained with Ni 7%/h-Beta. Ni loading also enhanced olefins saturation up to Ni 7%/h-Beta. High cetane indices (71–86) and octane numbers (89–91) were obtained over all the catalysts. Regarding the different studied Ni contents, Ni 7%/h-Beta constitutes a rather promising catalyst for obtaining high quality fuels from LDPE thermal cracking oils.     

有机硅改性破乳-絮凝剂在含油污水处理中的应用

采用破乳-絮凝法结合有机硅表面活性剂处理塔里木油田含油污水,以水样的油含量、Zeta电位、显微照片、界面张力为考察参数,得到一种新型水处理剂NP-22。NP-22为有机硅改性破乳-絮凝剂,其配方为破乳-絮凝剂YL-7和有机硅表面活性剂321的质量比95∶15。在NP-22加入量90 mg/L、反应温度45℃、沉降时间90min的优化条件下处理含油污水,水样的油含量由728.8 mg/L降至34.3 mg/L,除油率达95.3%。有机硅表面活性剂321可有效降低油水界面张力,与YL-7复合使用,可取得更好的除油效果。     

生物滴滤塔处理模拟甲硫醚废气

在常温条件下,采用生物滴滤塔处理模拟甲硫醚废气,考察了气体空床停留时间(EBRT)、容积负荷、喷淋密度及营养液pH对生物滴滤塔性能的影响。实验结果表明:当EBRT为90 s、进气甲硫醚质量浓度为150 mg/m~3、喷淋密度为0.65 m~3/(m~2·h),营养液pH为6.8时,甲硫醚去除率为90%;容积负荷高于15 g/(m~3·h)时,对生物滴滤塔的性能产生抑制作用;EBRT为90 s及60 s时,最佳喷淋密度分别为0.56~0.65 m~3/(m~2·h)及0.65~0.75 m~3/(m~2·h);降解甲硫醚的微生物对pH的变化较敏感,最适营养液pH为6~7。     

聚结晶紫膜修饰电极的制备及对水中对苯二酚和邻苯二酚的测定

通过电化学的方法将结晶紫聚合在玻碳电极表面制备聚结晶紫(PCV)膜修饰电极,并研究了对苯二酚和邻苯二酚在PCV膜修饰电极上的电化学行为。PCV膜修饰电极对对苯二酚和邻苯二酚的氧化有良好的电催化作用。在最佳的实验条件下,氧化峰电流在对苯二酚和邻苯二酚的浓度为4.0×10-6~2.8×10-4mol/L之间呈良好线性关系,对苯二酚和邻苯二酚的线性相关系数分别为0.9991和0.9823,检出限分别为6.2×10-7mol/L和9.0×10-7mol/L。PCV膜修饰电极具有良好的灵敏度、重现性和稳定性,可以应用于实际水样中两种物质的同时测定。     

Genotoxicity of leachates from highly polluted lowland river sediments destined for disposal in landfill

The Matanza-Riachuelo is one of the most polluted rivers of Latin America. The complex chemical mixture of pollutants discharged into the river is accumulated in the river sediments. In this paper, Matanza-Riachuelo river sediment composition and genotoxicity were tested in order to develop a cost-effective, environmentally sound option for disposal and management of contaminated dredged materials. Sampling was performed in a rural area, in a solid waste dumpsite and also in an urban and industrial area. The concentrations of total heavy metals increased from the upper basin to the lower basin. The Ames Salmonella typhimurium test and the Saccharomyces cerevisiae D7 test were performed using toxicity characteristic leachate procedure (TCLP) leachates. The concentrations of copper, lead, and chromium in the leachates exceeded the guide levels for the protection of aquatic life. Low concentrations of organic chlorinated compounds were detected in the leachates. Genotoxic profiles were obtained by testing TCLP leachates from polluted sediment samples with Salmonella typhimurium, Saccharomyces cerevisiae D7, and water sediment suspension with Allium cepa test. No mutagenicity effects on Ames test were observed. Gene conversion and mitotic reversion in Saccharomyces cerevisiae D7 and chromosome aberration in Allium cepa were induced by the sediment samples. Results obtained suggest that dredged sediments could be classified as genotoxic hazardous waste.     

一株吡啶降解菌的筛选及其降解性能

以吡啶为唯一碳源,从焦化厂活性污泥中分离得到一株对吡啶具有高效降解能力的菌株B1,对其进行了菌种鉴定。通过单因素实验研究了菌株B1适宜的降解条件,对反应过程进行了动力学拟合,并考察了菌株B1对焦化废水中吡啶的降解效果。实验结果表明:菌株B1为革兰氏阴性菌,属于不动杆菌属(Acinetobacter sp.);菌株B1适宜的降解条件为降解温度30℃、初始pH为7、摇床转速150 r/min;菌株B1对吡啶的降解过程符合零级反应动力学模型,当初始吡啶质量浓度为300 mg/L时,降解速率常数最高达到21.103 mg/(L·h);用菌株B1对初始吡啶质量浓度为430 mg/L的实际焦化废水处理74 h后,吡啶降解率可达74.26%。     

微正压气力输灰系统技术改进

对徐州发电厂7号炉微正压气力输送系统进、出料阀进行了技术改进，采用柔性阀板解决了卸灰装置磨损块的问题，系统可靠性大幅度提高，效果显著。     

Emission inventory of deca-brominated diphenyl ether (DBDE) in Japan

Atmospheric emissions of deca-brominated diphenyl ether (DBDE) in Japan were estimated based on the material flow of DBDE products and their emission factors. In 2002, the demand for DBDE in Japan was 2200 ton/year and the stock level was about 60 000 ton. The DBDE flow into the waste stream was estimated to be about 6000 ton/year and the flow out through second-hand product exports was more than 700 ton/year. Home appliance recycling facilities dismantle and crush domestic wastes containing about 600 ton of DBDE annually. Material recycling of crushed plastics is not commonly practiced as yet. Emission factors from plastics processing (2 × 10⁻⁹–1 × 10⁻⁷), textile processing (9 × 10⁻⁷), home appliance recycling (8 × 10⁻⁹–5 × 10⁻⁶), and waste incineration (1 × 10⁻⁷–2 × 10⁻⁶) were estimated using field measurement data. The DBDE emission rate through house dust during the service life of final products (2 × 10⁻⁷–9 × 10⁻⁷ per year) was estimated using the DBDE concentration in dust and the amount of dust in used televisions. Emission factors from previous studies were also used. The estimated total DBDE emission was 170–1800 kg/year. These results suggest the necessity of characterizing emissions during the service life of products, which is essential information for formulating an appropriate e-waste recycling strategy.     

超声辅助沉淀法制备γ-Bi_2MoO_6及其光催化性能

以Bi(NO3)3·5H2O和(NH4)6Mo7O24·4H2O为原料,采用超声辅助沉淀法制备了纳米可见光催化剂γ-Bi2Mo O6,用XRD,SEM,UV-Vis技术对其进行了表征,并以罗丹明B为目标降解物,考察了γ-Bi2Mo O6的可见光催化性能。表征结果显示,产物为高纯度正交结构的纳米γ-Bi2Mo O6,分散性良好。光催化实验结果表明:超声辅助沉淀法制备的γ-Bi2Mo O6的可见光催化活性优于普通沉淀法制备的产品;以超声辅助沉淀法制备的γ-Bi2Mo O6为光催化剂,在初始罗丹明B质量浓度为10 mg/L、初始溶液p H为7.2、γ-Bi2Mo O6加入量为10 g/L的最优条件下,反应180 min时的罗丹明B降解率达到97.48%。     

炼油废水污泥脱水工艺条件的优化

采用化学除油降黏—污泥调理—离心脱水工艺处理某炼油厂废水处理系统的混合污泥,并对工艺条件进行优化。实验结果表明,最佳的工艺条件为：化学除油降黏阶段处理体系的pH=4,反应温度35 ℃,H₂O₂加入量 2 g/L,m（H₂O₂）∶ m（Fe²⁺）=4,反应时间 60 min;污泥调理反应阶段的CaO加入量7.0 g/L;离心脱水阶段在分离因数为1 558时脱水5 min。在此条件下,得到的泥饼的含水率为70.0%~75.0%（w）,含油率小于2%（w）,污泥比阻约为3.0×10⁷ s²/g。