Adsorption Efficiency of Polyaspartate-Montmorillonite Composite Towards the Removal of Pb(II) and Cd(II) from Aqueous Solution

The selective modification of sodium montmorillonite (Na⁺-Mt) surface with polyionene followed by poly (succinimde-co-aspartate) has been considered. Na⁺-Mt was allowed to react with well characterized polyionene in two fold excess. The resulting polyionene/Mt (IC) was further modified with poly (succinimide-co-aspartate) through an ion exchange process. The obtained polyaspartate/Mt (IPS) composite was characterized by elemental analysis, X-ray diffraction, FTIR spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and BET surface analyzer. The adsorption efficiency of IPS composite was investigated for the removal of Pb(II) and Cd(II) from aqueous solution under different experimental conditions including initial metal ions concentration, temperature and single and binary mixture systems of metal ions. The experimental data were analyzed by Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models. Langmuir model reveals that the monolayer adsorption capacity of IPS was 92.59 and 67.57 mg/g for Pb(II) and Cd(II), respectively. The modification of parent Na⁺-Mt enhanced their adsorption capacity by about 87.91 and 29.84% for Pb(II) and Cd(II), respectively, due to inclusion of extra active sites of polyaspartate. The mean sorption energy, E calculated from Dubinin–Radushkevich isotherm were 2.75 and 1.98 kJ/mol for the adsorption of Pb(II) and Cd(II), respectively, indicating physical adsorption process. Also, The thermodynamic parameters were calculated and indicated that the adsorption was spontaneous and exothermic process. The mechanism of cation exchange and complexation of metal ions was suggested. IPS composite has a considerable potential for the removal of heavy metal ions from aqueous solution and wastewater stream.     

Effect of Poly(l-Lactide) and Poly(Butylene Succinate) on the Growth of Red Pepper and Tomato

Seeds of red pepper and tomato were sowed and cultivated in a soil blended with powdery poly(l-lactide) (PLLA), and poly(butylene succinate) (PBS). PBS depressed the growth of the two plants significantly even at a concentration as low as 5%, whereas PLLA up to 35% affected negligibly or even boosted the growth of the two plants. pH and number of microbial cells in the soil after 80 days of cultivation were almost the same independently whether the soil was blended with the two polymers or not. In contrast, the molecular weight of PBS decreased much faster than that of PLLA. Because succinic acid and 1,4-butane diol, from which PBS was synthesized, exhibited toxicity to both plant and animal cells to retard the germination rate of young radish seeds and to deform the morphology of HeLa cells significantly [1], the monomers and the oligomers produced from the PBS degradation should have a detrimental influence on the growth of the two plants.     

Synthesis and characterizations of Zr(IV)-loaded orange waste for effective sequestration of Mo(VI) and W(VI) from water

Journal of Material Cycles and Waste Management - An efficient and environmentally benign biosorbent for Mo(VI) and W(VI) sequestration was developed by loading Zr(IV) ions onto Saponified Orange...     

Influence of poly(bisphenol A carbonate) and poly(ethylene terephthalate) on poly(vinyl chloride) dehydrochlorination

Recycling of poly(vinyl chloride) (PVC) waste is a serious problem because of its high chlorine content. Dehydrochlorination of PVC-containing polymer waste produces solid residue char, for which conversion to pyrolysis oil in a petrochemical plant seems to be an attractive way of recycling PVC waste. Unfortunately, some polymer admixtures react with HCl and cause formation of chloroorganic compounds in a char. This article describes the influence of polycarbonates and poly(ethylene terephthalate) on thermal feedstock recycling of PVC wastes using a two-stage method. It was found that the presence of polycarbonate causes the formation of small amounts of benzyl chloride and other chloroaryl or chloroalkylaryl compounds. Poly(ethylene terephthalate) interacts with HCl forming significant amounts of various chlorocompounds – mainly chloroethyl esters of terephthalic and benzoic acids, but derivatives possessing chlorine directly connected to the aromatic ring are also formed.     

Thermal and mechanical properties of poly(lactic Acid) and poly(ethylene/butylene Succinate) blends

In this study, blends of poly (lactic acid) (PLA) with poly(ethylene/butylene succinate) (Bionolle) have been investigated for their thermal and mechanical properties as a function of the concentration of Bionolle. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and tensile tests were used to characterize the blends. From the results of the DMA and DSC, it was found that this blend system was not miscible within the compositions studied. DSC results showed that adding Bionolle aids in crystallization of PLA. It was observed that increasing the Bionolle concentration led to a slight increase in the strain-at-break of the blends but a decrease in the Young’s modulus and ultimate tensile strength. Biaxially oriented films showed an increase in tensile strength, modulus, and strain-at-break.     

Microbial degradation of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) in compost

The microbial degradation of tensile test pieces made of poly(3-hydroxybutyrate) [P(3HB)] or copolymers with 10% [P(3HB-co-10%3HV)] and 20% [P(3HB-co-20%3HV)] 3-hydroxyvaleric acid was studied in small household compost heaps. Degradation was measured through loss of weight (surface erosion) and changes in molecular weight and mechanical strength. It was concluded, on the basis of weight loss and loss of mechanical properties, that P(3HB) and P(3HB-co-3HV) plastics were degraded in compost by the action of microorganisms. No decrease inM _w could be detected during the degradation process. The P(3HB-co-20%3HV) copolymer was degraded much faster than the homopolymer and P(3HB-co-10%3HV). One hundred nine microbial strains capable of degrading the polymersin vitro were isolated from the samples used in the biodegradation studies, as well as from two other composts, and identified. They consisted of 61 Gram-negative bacteria (e.g.,Acidovorax facilis), 10 Gram-positive bacteria (mainlyBacillus megaterium), 35Streptomyces strains, and 3 molds.     

Effect of the Recycling and Annealing on the Mechanical and Fracture Properties of Poly(Lactic Acid)

The aim of this work is to evaluate the use of Poly(lactic acid) (PLA) industrial waste as a source of raw material for certain applications, as well as to understand the effects of the annealing on the fracture behavior of PLA. PLA waste has been simulated by an initial step of extrusion in a single screw extruder and pelletizing. Specimens of virgin and reprocessed PLA were obtained by injection molding. An annealing treatment capable of increasing the percentage of crystallinity (determined by differential scanning calorimetry) was also analyzed in reprocessed and non reprocessed specimens. The fracture behavior was studied at slow and high testing speed, applying the linear elastic fracture mechanics (LEFM) on single edge notched bend (SENB) specimens. This study revealed that the fracture toughness of the reprocessed PLA was basically the same that the virgin PLA and also that the increase in the crystalline fraction produced an improvement on the fracture toughness, at slow loading rate.     

Magnetic Cr(VI) Ion Imprinted Polymer for the Fast Selective Adsorption of Cr(VI) from Aqueous Solution

In this study, a novel magnetic Cr(VI) ion imprinted polymer (Cr(VI)-MIIP) was successfully synthesized and used as a selective sorbent for the adsorption of Cr(VI) ions from aqueous solution. It can be synthesized through the combination of an imprinting polymer and magnetic nanoparticles. The high selectivity achieved using MIIP is due to the specific recognition cavities for Cr(VI) ions created in Cr(VI)-MIIP. Also, the magnetic properties that could be obtained using magnetic nanoparticles, helps to separate adsorbent with an external magnetic field without either additional centrifugation or filtration procedures. The magnetic Fe₃O₄ nanoparticles (MNPs) were synthesized using an improved co-precipitation method and modified with tetraethylorthosilicate (TEOS) before imprinting. The magnetic Cr(VI) ion imprinted polymer was prepared through precipitation copolymerization of 4-vinylpyridine as the complexing monomer, 2-hydroxyethyl methacrylate as a co-monomer, the Cr⁶⁺ anion as a template, and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the presence of modified magnetite nanoparticles. This novel synthesized sorbent was characterized using different techniques. Batch adsorption experiments were performed to evaluate the adsorption conditions, selectivity, and reusability. The results showed that the maximum adsorption capacity was 39.3 mg g^?1, which was observed at pH 3 and at 25?°C. The equilibrium time was 20 min, and the amount of adsorbent which gave the maximum adsorption capacity was 1.7 g L^?1. Isotherm studies showed that the adsorption equilibrium data were fitted well with the Langmuir adsorption isotherm model and the theoretical maximum adsorption capacity was 44.86 mg g^?1. The selectivity studies indicated that the synthesized sorbent had a high single selectivity sorption for the Cr(VI) ions in the presence of competing ions. Thermodynamic studies revealed that the adsorption process was exothermic (\(\Delta H\)?<?0) and spontaneous (\(\Delta G\)?<?0). In addition, the spent MIIP can be regenerated up to five cycles without a significant decrease in adsorption capacity.     

Biodegradable Poly(butylene succinate) and Poly(butylene adipate-co-terephthalate) Blends: Reactive Extrusion and Performance Evaluation

Two biodegradable polyesters, poly(butylene adipate-co-terephthalate) (PBAT) and poly(butylene succinate) (PBS) were melt-compounded in a twin screw extruder to fabricate a novel PBS/PBAT blend. The compatibility of the blend was attributed to the transesterification reaction that was confirmed by Fourier transform infrared spectroscopy. The Gibbs free energy equation was applied to explain the miscibility of the resulting blend. Dynamic mechanical analysis of the blends exhibits an intermediate tanδ peak compared to the individual components which suggests that the blend achieved compatibility. One of the key findings is that the tensile strength of the optimized blend is higher than each of the blended partner. Rheological properties revealed a strong shear-thinning tendency of the blend by the addition of PBAT into PBS. The phase morphology of the blends was observed through scanning electron microscopy, which revealed that phase separation occurred in the blends. The spherulite growth in the blends was highly influenced by the crystallization temperature and composition. In addition, the presence of a dispersed amorphous phase was found to be a hindrance to the spherulite growth, which was confirmed by polarizing optical microscopy. Furthermore, the increased crystallization ability of PBAT in the blend systems gives the blend a balanced thermal resistance property.     

Biosorptive removal of Pb(II) and Cu(II) from wastewater using activated carbon from cassava peels

The ability of activated carbon from cassava peels to remove heavy metals like Cu(II) and Pb(II) from hospital wastewater was investigated. The study showed that a pH of 8 was the best for the sorption of both metal ions onto the biosorbent. The time-dependent experiments for the metal ions showed that the binding of the metal ions to the biomass was rapid and occurred within 20–120 min. Sorption efficiency increased with a rise in adsorbent dosage. It increased from 12 to 73 % for Pb(II) and 26 to 79 % for Cu(II) when the adsorbent dose increased from 2 to 12 g. An increase in temperature led to an increase in sorption for both metal ions. The Langmuir model showed that the biomass has a higher sorption capacity for Cu(II) than Pb(II), with q _m = 5.80 mg g^?1 for Pb(II) and 8.00 mg g^?1 for Cu(II). The Freundlich isotherm K _f was 1.4 for Pb(II) and 1.8 for Cu(II), indicating a preferential sorption of Cu(II) onto the biosorbent. Adsorption capacity was found to decrease with an increase in particle sizes. Sorption occurred by physical mechanisms and was mainly controlled by intraparticle diffusion.     

Engineering and Processing of Poly(HydroxyButyrate) (PHB) Modified by Nano-sized Graphene Nanoplatelets (GNP) and Amino-Functionalized Silica (A-fnSiO<Subscript>2</Subscript>)

Manufacturing of plastics by biodegradable polymers can reduce the environmental impact and limit the recourse to non-renewable resources. Physical, chemical and mechanical properties of biodegradable polymers cannot often be comparable with petroleum-based plastics. However, the modification of bioplastics by physical and chemical routes can improve their performance. In this work, Poly(HydroxyButyrate) PHB is reprocessed by the dispersion of graphene nano-platelets as well as by the dispersion of Amino-Functionalized Nano-Silica (A-fnSiO₂). Modification of the PHBs after compounding and pelletizing was evaluated by Fourier Transform Infrared. Thermal analysis was performed by Differential Scanning Calorimetry after extrusion and compression moulding. Hardness and scratch performance of the polymers were measured on compression molded substrates by pencil and progressive and constant load scratch tests. Chemical resistance was evaluated on compression molded substrates by dipping in aggressive acidic, basic and saline aqueous solutions. In conclusion, the PHBs modified by the graphene nanoplatelets were found to be very promising, featuring good chemical inertness, hardness and mechanical strength.     

Biosynthesis and Characterization of Laccase Catalyzed Poly(Catechol)

Enzymatic polymerization of catechol was conducted batch-wise using laccase enzyme produced by the culture Trametes versicolor (ATCC 200801). The polymerization reaction was carried out in 1:1 (v/v) aqueous-acetone solution, buffered at pH 5.0 with sodium acetate (50 mM) in a sealed, temperature-controlled reactor at 25°C. The molecular weight of the produced polymer was determined with GPC. FT-IR, DSC, and TGA were employed to investigate the structure and thermal behavior of synthesized poly(catechol). It was found that catechol units were linked together with ether bonds and thermal stability of the catechol increased in the poly(catechol) polymeric structure effectively. The number average molecular weight of poly(catechol) was found as 813 ± 3 Da with a very narrow polydispersity value of 1.17 showing selective polymerization of catechol by the enzyme.     

Effects of gaseous NH(3) and SO(2) on the concentration profiles of PCDD/F in flyash under post-combustion zone conditions

The influence of gaseous ammonia and sulphur dioxide on the formation of 2378-substituted PCDD/F on a reference flyash from a municipal waste incinerator has been investigated using a laboratory scale fixed-bed reactor. The reference flyash samples (BCR-490) was reacted under a simulated flue gas stream at temperatures of 225 and 375°C for 96h. The experiments were carried out in two series: first with simulated flue gas alone, and then with injection of NH(3) or SO(2) gas into the flue gas just before the reactor inlet. It was found that the injection of gaseous ammonia into the flue gas could decrease the concentration of both PCDD and PCDF by 34-75% from the solid phase and by 21-40% from the gas phase. Converting the results to I-TEQ values, it could reduce the total I-TEQ values of PCDD and PCDF in the sum of the flyash and exhaust flue gas by 42-75% and 24-57% respectively. The application of SO(2) led to 99% and 93% reductions in the PCDD and PCDF average congener concentrations, respectively in the solid phase. In the gas phase, the total reductions were 89% and 76% for PCDD and PCDF, respectively. Moreover, addition of SO(2) reduced the total I-TEQ value of PCDD and PCDF in the flyash and exhaust flue gas together by 60-86% and 72-82% respectively. Sulphur dioxide was more effective than ammonia in suppressing PCDD/F formation in flyash under the conditions investigated.     

Distribution of inorganic bromine and metals during co-combustion of polycarbonate (BrPC) and high-impact polystyrene (BrHIPS) wastes containing brominated flame retardants (BFRs) with metallurgical dust

This study focused on the thermal degradation of polycarbonate (BrPC) and high-impact polystyrene (BrHIPS), containing different brominated flame retardants. The evolved inorganic bromine was utilized for the separation of metals present in electric arc furnace dust (EAFD). The thermal degradation of BrPC generated inorganic gaseous HBr (69%) and condensable Br₂ (31%). The bromine evolved from BrHIPS was detected almost entirely in a condensed phase as SbBr₃. When mixed with EAFD, the evolved inorganic bromine reacted immediately with the metallic components of zinc and lead, but not with iron. The best bromination efficiencies were obtained during the isothermal heating (80 min at 550 °C) of the mixtures at mass ratios of 6:1 and 9:1 w/w under oxidizing conditions. The achieved brominating rates reached 78 and 81% for zinc and 90 and 94% for lead in 6:1 and 9:1 BrPC:EAFD, respectively, and 47 and 65% for zinc and 67 and 63% for lead in 6:1 and 9:1 BrHIPS:EAFD, respectively. The oxidizing condition favored complete vaporization of the formed bromides.     

Chemiluminescence in evaluating the thermal oxidative stability of acrylonitrile-butadiene-styrene (ABS) copolymers. II. ABS/polycarbonate (PC) blends

The thermal oxidative stability of various ABS/PC compounds was studied by means of the chemiluminescence technique. Similarly to pure ABS, Irganox 1076 and Irganox MD 1024 perform as moderate antioxidants in ABS/PC and (ABS/PC + lubricant) blends. Neither Tinuvin 144, Irgaphos 168, nor their mixture affects the durability of the ABS/PC blend. At the same time, (Irgaphos 168 + Tinuvin 144) in combination with Irganoxes was found to provide a noticeable enhancement in durability to the (ABS/PC + lubricant) system. Titanium dioxide pigments by themselves have only a slight influence on the oxidative stability of the ABS/PC blend. Durability of the (ABS/PC + pigment) and (ABS/PC + lubricant) systems was found to be the same and the overall protective effect of Irganox 1076 was similar in both the (ABS/PC + lubricant) and the (ABS/PC + lubricant + pigment) systems. Certain modifiers significantly improve the durability of the ABS/PC compounds, although their function may differ in the systems with and without pigments.Guest Editor: Dr. Graham Swift, Rohm & Haas.     

Transfer of Graphene CVD to Surface of Low Density Polyethylene (LDPE) and Poly(butylene adipate-co-terephthalate) (PBAT) Films: Effect on Biodegradation Process

Here, the influence of graphene as a coating on the biodegradation process for two different polymers is investigated, poly(butylene adipate-co-terephthalate) (PBAT) (biodegradable) and low-density polyethylene (LDPE) (non-biodegradable). Chemical vapor deposition graphene was transferred to the surface of two types of polymers using the Direct Dry Transfer technique. Polymer films, coated and uncoated with graphene, were buried in a maturated soil for up to 180 days. The films were analyzed before and after exposure to microorganisms in order to obtain information about the integrity of the graphene (Raman Spectroscopy), the biodegradation mechanism of the polymer (molecular weight and loss of weight), and surface changes of the films (atomic force microscopy and contact angle). The results prove that the graphene coating acted as a material to control the biodegradation process the PBAT underwent, while the LDPE covered by graphene only had changes in the surface properties of the film due to the accumulation of solid particles. Polymer films coated with graphene may allow the production of a material that can control the microbiological degradation, opening new possibilities in biodegradable polymer packaging. Regarding the possibility of graphene functionalization, the coating can also be selective for specific microorganisms attached to the surface.     

Examination of the influence of dissolved halite (NaCl) on the leaching of lead (Pb) from cement-based solidified wastes

The leaching of lead from cement-based solidified waste forms mixed at different water/cement ratios was studied by conducting equilibrium and semi-dynamic leaching tests using deionized water and sodium chloride solutions. The results suggest that leaching of the primary constituents of the cement (calcium, silicon and sulfate) is controlled by solubility equilibria, with increased leaching into chloride solutions due to ionic strength effects. The original porosity of the waste forms increased with water/cement ratio and chloride solutions further increased it as a result of decalcification. Lead leaching was generally low, and appears to be a transport-controlled process, such that leaching correlates positively with porosity.     

Polychlorinated biphenyls (PCBs) and halogenated flame retardants (HFRs) in multi-matrices from an electronic waste (e-waste) recycling site in Northern China

The present study investigated the occurrence of polychlorinated biphenyls (PCBs) and halogenated flame retardants (HFRs) in soil, water, reed, air and dust samples collected from the e-waste recycling region in Ziya Town, Northern China. The results showed that the concentrations of PCBs reached relative high level in environmental matrices in the study area. HFRs including polybrominated diphenyl ethers (PBDEs), dechlorane plus (DP), allyl 2,4,6-tribromophenyl ether (ATE), tetrabromoethylcyclohexane (TBECH), pentabromotoluene (PBT), pentabromoethylbenzene (PBEB), 2,3-dibromopropyl 2,4,6-tribromophenyl ether (DPTE), 1,2-bis-(2,4,6-tribromophenoxy) ethane (BTBPE) and so on were also widely detected in multi-matrices. Long-range atmospheric transport (LRAT) potentials of non-BDE HFRs were assessed to address the LRAR abilities of these compounds. Analysis of soil–air exchange of PCBs and HFRs showed that soil acted as a secondary source to the atmosphere only for a few low molecular weight compounds, while the direction of the flux of most detected chemicals was from air to soil.     

Utilization of Broken Rice for the Production of Poly(3-hydroxybutyrate)

The feasibility of utilizing non edible rice (broken rice) for production of fine materials such as poly(3-hydroxybutyrate) (PHB) was considered as one of the alternative ways of keeping the environment clean for sustainable development. Thus, production of PHB from broken rice by simultaneous saccharification and fermentation (SSF) was investigated. During the SSF process, the rice (15% w/v) material was hydrolyzed to glucose, which was utilized by Cupriavidus necator for growth and production of PHB. The PHB content reached 38% at 58 h fermentation. The PHB had weight average molar mass (Mw) and polydipersity index of 3.82 × 10⁵ (g/mol) and 4.15, respectively. Differential calorimetric scan of the PHB showed a melting temperature (Tm) of 176 °C. Given that the PHB was a homopolymer (which consisted of (R)-3-hydroxybutyric acid monomers), it was thought that broken rice could be a raw material for production of both PHB and (R)-3-hydroxybutyric acid. This SSF process would not only help in the utilization of broken rice or non edible rice, but would also serve as a model for utilization of other raw materials that contain starch for production of PHB.     

Effect of polyethylene terephthalate (PET) on the pyrolysis of brominated flame retardant-containing high-impact polystyrene (HIPS-Br)

Pyrolysis of brominated flame retardant-containing high-impact polystyrene (HIPS-Br) was performed at 430°C in the presence of 0.1 wt% of polyethylene terephthalate (PET) in a Pyrex glass reactor. Two different types of brominated flame retardants (decabromodiphenyl ether and decabromodiphenyl ethane) with or without antimony trioxide (as synergist) 5 wt% were used. The presence of PET had a significant effect on the material balance, decreasing the gaseous product and increasing the residue. The type of flame retardant had no effect on the yield of liquid product; however, the presence of Sb resulted in a marked difference in the distribution of decomposition products. Analysis by a gas chromatograph equipped with a flame ionization detector showed that the hydrocarbons were distributed in the range n-C₇ to n-C₂₅ with major peaks at n-C₉ and n-C₁₇. The presence of PET increased the formation of brominated compounds by several times and affected both the type and quantity of polybrominated compounds. The liquid products obtained from the pyrolysis of HIPS-Br/PET have to be treated before they can be used