Experimental Investigation of Cellulose/Silver Nanocomposites Using In Situ Generation Method

Cellulose gel films were prepared by regeneration process using pre-cooled aq.(8 wt% LiOH + 15 wt% urea) mixture as solvent and ethyl alcohol as non solvent. The Terminus cattapa leaf extract diffused wet cellulose films were then dipped in 1–5 mM aq.AgNO₃ solutions to allow in situ generation of silver nanoparticles (AgNPs). Besides the in situ generation, some AgNPs were also formed outside the wet films in the solution. The AgNPs formed outside the films were observed under transmission electron microscope and scanning electron microscope. The nanocomposite films were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction and thermogravimetric analysis and tensile test. The thermal stability of the composite films was lower than that of the matrix up to a temperature of ~300 °C and afterwards showed a reverse trend. The tensile strength of the nanocomposite films was found to be higher than the matrix but decreased with increasing concentration of aq.AgNO₃. The cellulose/AgNPs composite films showed good antibacterial activity against E. coli (gram positive) and Bacillus sp. (gram negative). Based on the aforementioned properties, the cellulose/AgNPs composite films can be considered for antibacterial packaging and medical applications.     

Fabrication of a Novel Fibrous Mat Based on Gliadin/Ethylcellulose Incorporated with Triamcinolone for Treatment of Oral Ulcers

Journal of Polymers and the Environment - Eelectrospun fibrous mats for oral ulcer dressing should be able to attach oral mucosa in a high moisture environment and provide desirable therapeutic...     

Effect of Sequential Mixing and Compounding Conditions on Cellulose Acetate/Layered Silicate Nanocomposites

Injection molded nanocomposites have been successfully fabricated from cellulose acetate (CA), eco-friendly triethyl citrate (TEC) plasticizer, and organically modified clay with and without maleic anhydride grafted cellulose acetate butyrate (CAB-g-MA) as a compatibilizer. The effects of processing conditions such as mixing methods, pre-plasticizing times, extruder retention times (RT) and addition of compatibilizer on the performance of these nanocomposites have been evaluated. The cellulosic plastic with CA/TEC (80/20 wt%) was used as the polymer matrix for nanocomposite fabrication. The morphologies of these nanocomposites were evaluated through X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies. The mechanical properties of the nanocomposites were measured and have been correlated with the XRD and TEM observations. From all of the sequential mixing methods used, powder–powder mixing leads to the most transparent nanocomposites. Cellulosic plastic-based nanocomposites obtained using increased pre-plasticizing times and RT showed better exfoliated structures. In the system containing compatibilizer, the minimum retention time required for obtaining almost completely exfoliated hybrid nanocomposites was shorter than in the system without compatibilizer.     

Mechanical and Physical Properties of Green Biocomposite Based on Medium Density Fiberboard Sanding Powder/Polyethylene/Nanoclay

Medium density fiberboard (MDF) sanding powder is an industrial waste that has not been yet used as a raw material to produce composites. In this study, the influence of nanoclay particles on the flexural and impact strengths and the withdrawal strength of green biocomposites (based on MDF sanding powder/polyethylene/nanoclay) were investigated. For this aim, medium density fiberboard sanding dust and polyethylene were used as the lignocellulosic and thermoplastic material, respectively. In addition, maleic anhydride grafted polyethylene was used in three weight percentages (0, 3 and 6 %) as a coupling agent and compatibilizer, and Cloisite^®15A was used in four weight percentages (0, 2, 4 and 6 %). To prepare samples, wood-plastic granules were produced by using a twin-screw extruder followed by the hot pressing method. The mechanical and physical properties were measured according to the CEN/TS15534:2007 and ASTM-D256 technical specifications. The results showed that the coupling agent improved the mechanical and physical properties of biocomposites; however, its effect might be affected by the nanoclay particles. Furthermore, the ultrastructure of the biocomposites was surveyed with SEM.     

钛基锡锑电极电催化氧化处理硝基苯废水

采用钛基锡锑(Sn-Sb/Ti)电极作为氧化阳极,不锈钢为阴极,电催化氧化降解废水中硝基苯。实验结果表明,处理硝基苯废水的最佳条件为:电流密度25 mA/cm~2;Na_2SO_4作为电解质,加入量15g/L;极板间距2 cm;溶液初始pH 6。在此最佳条件下,硝基苯去除率大于95%,TOC去除率大于80%,表明Sn-Sb/Ti阳极能有效去除废水中有机污染物。     

Novel Fabrication of PAA/PVA/Yeast Superabsorbent with Interpenetrating Polymer Network for pH-Dependent Selective Adsorption of Dyes

Traditional superabsorbent polymers have wide application potential as an adsorbent, but the poor physical and mechanical properties limit their further applications. To tentatively overcome this dilemma, a novel poly(acrylic acid)/poly(vinyl alcohol)/yeast superabsorbent polymers (PAA/PVA/yeast SAPs) with interpenetrating polymer networks (IPNs) were fabricated herein via solution polymerization. The mechanical stability tests showed that the resulting products could desirably resist the destruction of shear flow (<5000 rpm) and load pressure (<3 kg). The effects of yeast content, pH, contact time, initial dye concentration and temperature were systematically studied to evaluate their adsorption properties. Consecutive five cycles of adsorption–desorption indicated that their easy regeneration and reusability. More importantly, the PVA/PAA/yeast SAPs displayed brilliant pH-dependent selective adsorption for dyes in dye mixtures. It is believed hereby that the PAA/PVA/yeast SAPs can be expected to be economically and technically feasible for the scalable treatment of dyes wastewater.     

采用Zn-Se/不锈钢阴极的超声-电解法处理罗丹明B废水

采用超声-电解法考察了Zn-Se/不锈钢阴极处理罗丹明B废水的效果及影响因素。正交实验优化结果表明:在电流密度为2.4A/dm2、废水初始pH为6、超声功率为160W、通气量为10L/h、m(Zn)∶m(Se)为1∶1.5的Zn-Se/不锈钢作阴极、Ti/TiO2和铁网为双阳极的条件下,超声-电解法处理罗丹明B废水120min,废水脱色率为98.97%,COD去除率为88.11%。     

用活性炭纤维吸附处理十三吗啉农药废水的研究

介绍用活性炭纤维处理十三吗啉农药废水的工艺过程。研究了活性碳纤维对该种有机废水的吸附规律及脱附再生方法，并探索了其使用寿命。实验表明，用活性炭纤维处理十三吗啉农药废水，ＣＯＤｃｒ由２４６２ｍｇ／Ｌ可降至１５０ｍｇ／Ｌ以下，净化率达９４％。     

Integrated Treatment of Mining Dam Wastewater with Quaternized Chitosan and PAN/HPMC/AgNo3 Nanostructured Hydrophylic Membranes

Journal of Polymers and the Environment - This study was developed a novel nanostructured membrane by electrospinning process, from polyacrylonitrile (PAN) modify by hydroxypropyl methylcellulose...     

用松香胺萃取处理含酚废水的研究

用松香胺萃取处理模拟含酚废水。研究了萃取剂组成、油水比、废水酸度对分配系数的影响,萃取温度、萃取时间对脱酚效率的影响,以及反萃剂的浓度、用量和反萃温度对反萃率的影响。     

Fe_2O_3/膨润土微波诱导氧化处理染料废水

以膨润土为载体,采用直接沉淀法制备了Fe2O3/膨润土负载型催化剂。制备催化剂的最佳工艺条件:硝酸铁质量浓度为8.08g/L,硝酸铁与膨润土质量比为1.0,焙烧温度为350℃,焙烧时间为3h。用Fe2O3/膨润土负载型催化剂微波诱导氧化处理50mL质量浓度为50mg/L的模拟活性嫩黄废水的最佳工艺条件:催化剂加入量为0.5g,微波功率为900W,微波作用时间为5min。在此条件下模拟活性嫩黄废水脱色率达96.40%。微波诱导氧化处理模拟活性嫩黄废水的反应符合一级反应动力学方程。     

工程菌处理印染废水工艺条件的研究

由于工程菌LEY5－LEY4组成的厌氧－好氧生化系统处理印染废水的影响因素和工艺条件进行了研究，通过正交试验确定了最佳工艺条件，菌体家度为2.0g/L，停留时间为10h,pH为8．0，通气量为1.85L/min。在最佳工艺条件下，系统对印废水的COD去除率为77．8％，脱色率为72．6％。     

500t／h污水处理场开车总结及几点建议

介绍了胜利石化总厂５００ｔ／ｈ污水处理场的流程,总结了开车后遇到的问题、采取的措施及取得的效果,并结合本厂实际提出了改进意见。     

Life Cycle Analysis of Extruded Films Based on Poly(lactic acid)/Cellulose Nanocrystal/Limonene: A Comparative Study with ATBC Plasticized PLA/OMMT Systems

Life cycle analysis (LCA) of limonene plasticized poly(lactic acid) (PLA) films containing cellulose nanocrystals (CNC) extracted, by acid hydrolysis, from Phormium tenax leaf fibres, was assessed and compared with the results of acetyl tributyl citrate (ATBC) plasticized PLA films, having equivalent mechanical properties, containing organo-modified montmorillonite (OMMT). Eco-Indicator 99 tool has been adopted as the main method for life cycle assessment. Results indicated that, despite CNC are biobased fillers obtained by natural sources, the related chemical extraction leads to a large environmental footprint and a relatively relevant energy expense. LCA characterization of these films demonstrated that the environmental impact of PLA/limonene film reinforced with 1% in weight of CNC (PLA/CNC/limonene) is comparable to the environmental impact of polylactic acid films reinforced with OMMT and plasticized with a petroleum based plasticizer (ATBC) (PLA/OMTT/ATBC). A “cradle to gate” approach has been considered for both the film typologies.     

TiO2光催化氧化处理偶氮染料废水的研究进展

二氧化钛具有较高的光稳定性和反应活性,可用于处理偶氮染料废水,对二氧化二钛光催化氧化的影响因素、提高二氧化钛光能化氰化处理偶氮染料废水效率的途径和比催化氧化联用处理技术进行了综述,提出今后研究重点是扩展二氧化钛对可见光的光谱响应、提高太阳光的利用率以及加强气-质联用、液-质联用技术在处理偶氮染料废水中的应用。     

Novel Composite Films Based on Acrylic Fibers Waste/Nano-chitosan for Congo Red Adsorption

Journal of Polymers and the Environment - The current research aimed to use waste to treat waste; to recycling of acrylic fibers waste combined with nano-chitosan for use as an adsorbent to remove...     

Biobased Contents of Organic Fillers and Polycaprolactone Composites with Cellulose Fillers Measured by Accelerator Mass Spectrometry Based on ASTM D6866

The biobased contents of raw materials such as starches, sugar, chitin, or wood powders for biomass plastics were measured using Accelerator Mass Spectrometry (AMS) based on ASTM D6866. AMS measures the isotope carbon ratio of ¹⁴C to ¹²C and ¹³C in graphite derived from sample powders. The biobased contents of starches, sugar or chitin were almost 100% which means that they are fully biobased. The biobased contents of the wood powders were over 140% due to the effect of the post 1950s ¹⁴C injection due to nuclear testing. Poly(ε-caprolactone) (PCL) composite samples were prepared using the polymerization and direct molding method. The starting compound was the ε-caprolactone monomer liquid combined with cellulose and inorganic fillers using aluminum triflate as a catalyst at 80 °C for 6 or 24 h. PCL cylinder-shaped composite samples with a homogeneously dispersed cellulose filler were prepared with M_n = 4,600 (M_w/M_n = 2.9). The biobased content of the PCL composite with 50 wt% cellulose filler (51.67%) measured using AMS was slightly higher than the carbon ratio of cellulose in the starting powder samples (41.3 mol%). This is due to the higher biobased content (112.70%) of the cellulose filler used in this study. The biobased content of the polymer composite powders by AMS was found not to be affected by the presence of inorganic fillers, such as talc.     

Development of a Novel Antibacterial Hydrogel Scaffold Based on Guar Gum/Poly (methylvinylether-alt-maleic Acid) Containing Cinnamaldehyde-Loaded Chitosan Nanoparticles

Journal of Polymers and the Environment - In this study, we produced a novel chemical cross-linked Guar gum/Poly(methylvinylether-alt-maleicacid) (GG/PMVE-MA) hydrogels with various blending weight...     

Nanocomposite Film Based on Gluten Modified with Heracleum persicum Essence/MgO/Polypyrrole: Investigation of Physicochemical and Electrical Properties

In this study, the wheat gluten film was prepared. Heracleum persicum essence, magnesium oxide nanoparticles and polypyrrole were used to modify the structure of the wheat gluten film. Physicochemical properties of the prepared films such as thickness, solubility, moisture absorption ability, antioxidant properties, and electrical conductivity of the films were investigated. Also, the mechanical, structural and thermal properties of the films were investigated by techniques such as SEM, FTIR, XRD, TGA, DTA and tissue analysis. SEM images showed that the essence and polypyrrole strengthened the gluten film structure and made it more resistant to the passage of gases. FTIR spectra confirmed the electrostatic interactions between gluten and essence and polypyrrole. XRD spectra showed the amorphous structure of gluten film and its composites. The results of thermal analysis showed that polypyrrole greatly increased the thermal resistance of the film and the nanoparticles had little effect on the thermal resistance. Thickness, solubility, moisture content and ability to absorb moisture were further affected by the essential oil. The antioxidant and electrical conductivity of the film was greatly increased in the presence of all three additives of essence, magnesium oxide nanoparticles and polypyrrole. The gluten–essence–MgO–PPy (Glu–E–MgO–PPy) composite film had the most antioxidant properties. Glu–E–MgO–PPy film with important electrical conductivity and antioxidant properties has the potential to be used as an active and intelligent film in the packaging of perishable food products.

     

The Investigation of the Toughening Mechanism of PHBV/PBAT with a Novel Hyperbranched Ethylenediamine Triazine Polymer Based Modifier: The Formation of the Transition Layer and the Microcrosslinking Structure

A new type of designed hyperbranched ethylenediamine trazine polymer (HBETP) is successfully synthesized and characterized based upon NMR and GPC. The prepared HBETP is used to modify the poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV)/poly(butylene adipate-co-terephthalate) (PBAT) blends. The effect of HBETP on the microstructure, mechanical properties and thermal properties of the blends is studied. The results indicate that upon addition of 1.0 wt% of HBETP, the impact strength of the PHBV/PBAT blends is increased by 47.1%; ?T_g of the blends decreases from 53.2 to 49.9 °C. These results, together with the morphology analysis of the fractured surface of the blends, conclude the formation of the transition layer between PHBV and PBAT. Also, the XRD result shows that the addition of HBETP can limit the growth of the PHBV crystals and causes the decrease of both the crystallinity and the grain crystalline size. The DSC result demonstrates that the addition of HBETP mainly affects the crystallization of the HB-HV binary eutectic region within PHBV. The mechanism of PHBV/PBAT toughening is due to the formation of the strong physical hydrogen bonding and the chemical micro-crosslinking between HBETP and PHBV/PBAT, which is proposed based on XPS characterization.