改进电动力技术去除铅锌矿尾砂中的重金属

采用改进的电动力技术去除铅锌矿尾砂中的Pb,Zn,Cu。研究了铅锌矿尾砂中重金属在改进电动力技术处理情况下的去除情况。实验结果表明,经过7d的电动力实验,Pb、Zn和Cu的总去除率分别为34％,33％,37％,其中酸溶态去除效果显著,分别达到66％,86％,81％。Pb和Cu的铁锰氧化物结合态去除率为39％和42％,其他形态去除率较低,在10％左右。     

Mechanical,Barrier and Antioxidant Properties of Chitosan Films Incorporating Cinnamaldehyde

Chitosan films (CF) [1 and 2% w/v] alone and with cinnamaldehyde (CNE) [0.25, 0.5 and 1% v/v] were prepared using an emulsion method, and the obtained films were characterized in terms of water vapor permeability (WVP), water solubility and optical, mechanical and antioxidant properties. The incorporation of CNE at 1% (v/v) significantly decreased the water solubility of the film by approximately 4% for the 1 and 2% CF films, whereas the WVP increased (2.5–3.5 times). The incorporation of CNE (0.25 and 0.5%) into 2% CF significantly increased the tensile strength (TS) (62 and 34%, respectively) and the percent elongation (%E) values, 26, 30 and 52% for CF that contained 0.25, 0.5 and 1% CNE, respectively. The largest value of the elasticity modulus (EM) was observed for 2% CF with 0.25% CNE. All films exhibited a yellow appearance (b*), but the CNE content had a marked impact on the coloration of the films. The CNE recoveries of the CF films (1 and 2%) with 1% of CNE were high (43 and 67%). The antioxidant activities indicated that the incorporation of 1% CNE into CF films (1 and 2%) increased the antioxidant activity. The protective effects of the films with and without CNE on erythrocytes were very strong (36–72% hemolysis inhibition). These results suggest there are potential applications for CF-CNE films as active packaging for the preservation of food products.     

Management of immunization solid wastes in Kano State, Nigeria

Inadequate management of waste generated from injection activities can have a negative impact on the community and environment. In this paper, a report on immunization wastes management in Kano State (Nigeria) is presented. Eight local governments were selected randomly and surveyed by the author. Solid wastes generated during the Expanded Programme on Immunization were characterised using two different methods: one by weighing the waste and the other by estimating the volume. Empirical data was obtained on immunization waste generation, segregation, storage, collection, transportation, and disposal; and waste management practices were assessed. The study revealed that immunization offices were accommodated in either in local government buildings, primary health centres or community health care centres. All of the stations demonstrated a high priority for segregation of the infectious wastes. It can be deduced from the data obtained that infectious waste ranged from 67.6% to 76.7% with an average of 70.1% by weight, and 36.0% to 46.1% with an average of 40.1% by volume. Non-infectious waste generated ranged from 23.3% to 32.5% with an average of 29.9% by weight and 53.9% to 64.0% with an average of 59.9% by volume. Out of non-infectious waste (NIFW) and infectious waste (IFW), 66.3% and 62.4% by weight were combustible and 33.7% and 37.6% were non-combustible respectively. An assessment of the treatment revealed that open pit burning and burial and small scale incineration were the common methods of disposal for immunization waste, and some immunization centres employed the services of the state or local government owned solid waste disposal board for final collection and disposal of their immunization waste at government approved sites.     

Functional Properties of Extruded Starch Acetate Blends

Starch acetate, with degree of substitution of 2, was blended with 0, 7.5 and 15% polylactic acid (PLA), Eastar Bio Copolyester 14766 (EBC) or Mater-Bi ZF03U (MBI) and 10%, 13%, or 16% (d.b.) ethanol and twin-screw extruded at 160°C barrel temperature. Physical characteristics of the extrudates, such as radial expansion ratio, unit and bulk densities, and of the mechanical properties, including unit spring index and bulk spring index, were measured. Type of polymer, polymer content, and ethanol content significantly affected the physical characteristics and mechanical properties. The sample extruded with 7.5% PLA and 13% ethanol had the highest expansion ratio and bulk spring index. The sample with 15% MBI and 16% ethanol had the lowest unit density, while the sample with 7.5% PLA and 16% ethanol had lowest bulk denisty. The highest unit spring index was expressed in the sample containing 7.5% PLA and 10% ethanol.     

苯甲酸生产残液中锰、钴和镍的提取及分离

探讨了苯甲酸生产残液中锰、钴和镍的提取及分离方法。首先采用酸溶液提取残液中的金属元素;然后通过氨水沉淀法分离锰;最后使用p507萃取剂分离钴和镍。实验结果表明:当苯甲酸生产残液中锰、钴和镍的质量分数分别为0.085 0%,0.307 1%,0.015 5%时,在硫酸浓度为2.0 mol/L、过氧化氢溶液质量分数为25%的条件下,锰、钴和镍的提取率分别为88.59%,87.77%,86.50%;当氨水浓度为2 mol/L时,锰的沉淀率达94.24%;在平衡水相p H为4、p507萃取剂皂化率为60%、油相中p507萃取剂的体积分数为15%的条件下,钴萃取率达87.53%,镍萃取率仅为8.46%,钴镍分离系数为68.70。     

Humidity- and Age-Tolerant Starch-Based Sponge for Loose-Fill Packaging

Loose-fill packaging sponges were extruded from mixtures of 54–62% hydroxypropylated (HP 5%) amylomaize V (50% amylose) and wheat starches, 17–24% synthetic polymer, 13% water, 7% blowing agent(s), and 0.5% nucleating agent. One product made from 28% HP wheat starch, 28% HP amylomaize V starch, 12% ethylene vinyl alcohol (EVOH) copolymer, 8% polystyrene (PS), and 3% polystyrene maleic anhydride (PSMA) copolymer, plus the other raw materials, had a compressibility and resilience that matched those of expanded polystyrene (EPS), although its bulk density was four times higher. The starchy sponge showed 16% shrinkage in volume at 90% relative humidity and was 2% soluble in excess water, both at 25°C. After aging for 18 months near 25°C, the HP starchy sponge gave only a trace of fines in a simulated shipping test, compared to 20% fines from a biodegradable, starch-based, loose-fill sponge of commerce.     

Count, identification and antimicrobial susceptibility of bacteria recovered from dental solid waste in Brazil

In Brazil, few studies on microbial content of dental solid waste and its antibiotic susceptibility are available. An effort has been made through this study to evaluate the hazardous status of dental solid waste, keeping in mind its possible role in cross-infection chain. Six samples of solid waste were collected at different times and seasons from three dental health services. The microbial content was evaluated in different culture media and atmospheric conditions, and the isolates were submitted to antibiotic susceptibility testing. A total of 766 bacterial strains were isolated and identified during the study period. Gram-positive cocci were the most frequent morphotype isolated (48.0%), followed by Gram-negative rods (46.2%), Gram-positive rods (5.0%), Gram-negative-cocci (0.4%), and Gram-positive coccobacillus (0.1%). Only two anaerobic bacteria were isolated (0.3%). The most frequently isolated species was Staphylococcus epidermidis (29.9%), followed by Stenotrophomonas maltophilia (8.2%), and Enterococcus faecalis (6.7%). High resistance rate to ampicillin was observed among Gram-negative rods (59.4%) and Gram-positive cocci (44.4%). For Gram-negative rods, high resistance was also noted to aztreonam (47.7%), cefotaxime (47.4%), ceftriaxone and cefazolin (43.7%), and ticarcillin-clavulanic acid (38.2%). Against Gram-positive cocci penicillin exhibit a higher resistance rate (45.0%), followed by ampicillin, erythromycin (27.2%), and tetracycline (22.0%). The present study demonstrated that several pathogenic bacteria are present in dental solid waste and can survive after 48 h from the waste generation time and harbor resistance profiles against several clinical recommended antibiotics.     

Filter-based treatment of leachate from an industrial landfill containing shredder residues of end-of-life vehicles and white goods

A pilot plant was set up to treat leachate from an industrial landfill containing shredder residues of end-of-life vehicles and white goods. The treatment plant consisted of aeration and sedimentation steps for pre-treatment, and a filter. The plant was designed to simultaneously remove various types of pollutants. The efficiencies of pre-treatment and of the main treatment step were investigated over a period of 3 years at the landfill site. By continuous aeration of the leachate the concentrations of Fe and Mn were reduced by 55% and 49%, respectively. By prolonged sedimentation suspended solid content was noticeably reduced (72%). In the filter, consisting of a mixture of peat and carbon-containing ash as a treatment medium, very high reduction of polar organic compounds, e.g. phenol (74%), o-and p-cresol (91%), and 2,4-dimethylphenol (73%), high average reduction of metals, e.g. Pb (78%), Fe (74%), Cu (73%), Mn (56%), Sn (55%), and Zn (47%), and good average reduction of DOC (26%), Tot-N (23%) and NH₄-N (46%) were achieved. Sixty non-polar compounds in the leachate, identified by GC–MS screening, occurred at trace level. Most of them were considerably reduced in the filter.     

改性累托石复合絮凝剂处理油漆废水

采用改性累托石-天然高分子多糖复合絮凝剂处理油漆废水。在改性累托石质量浓度为80mg／L、天然高分于多糖质造浓度为4mg／L的条件下,COD、悬浮固体和色度的去除率分别较传统絮凝剂三氯化铝和聚丙烯酰胺提高了43．1％,6．4％,22．6％和19．1％,3．4％,21．8％;吨废水药剂成本分别下降了16．9％和30．7％,处理后的油漆废水均达到国家二级污水排放标准。     

Evaluating impact level of different factors in environmental impact assessment for incinerator plants using GM (1, N) model

In this study, the impact levels in environmental impact assessment (EIA) reports of 10 incinerator plants were quantified and discussed. The relationship between the quantified impact levels and the plant scale factors of BeiTou, LiZe, BaLi, LuTsao, RenWu, PingTung, SiJhou and HsinChu were constructed, and the impact levels of the GangShan (GS) and YongKong (YK) plants were predicted using grey model GM (1, N). Finally, the effects of plant scale factors on impact levels were evaluated using grey model GM (1, N) too. According to the predicted results of GM, the relative errors of topography/geology/soil, air quality, hydrology/water quality, solid waste, noise, terrestrial fauna/flora, aquatic fauna/flora and traffic in the GS plant were 17%, 14%, 15%, 17%, 75%, 16%, 13%, and 37%, respectively. The relative errors of the same environmental items in the YK plant were 1%, 18%, 10%, 40%, 37%, 3%, 25% and 33%, respectively. According to GM (1, N), design capacity (DC) and heat value (HV) were the plant scale factors that affected the impact levels significantly in each environmental item, and thus were the most significant plant scale factors. GM (1, N) was effective in predicting the environmental impact and analyzing the reasonableness of the impact. If there is an EIA for a new incinerator plant to be reviewed in the future, the official committee of the Taiwan EPA could review the reasonableness of impact levels in EIA reports quickly.     

Investigating mechanical properties and durability of concrete containing recycled rubber ash and fibers

This article investigates the suitability of utilizing end of life rubber tyre particles in concrete as fine aggregate. Rubber ash and rubber fibers were used to develop two series of rubber ash concrete (series I) and hybrid concrete (series II) mixes. The natural fine aggregate was replaced by rubber ash (by volume of 5%, 10%, 15% and 20%) in series I; whereas in series II, the amount of rubber ash was kept constant at 10% and rubber fiber was introduced as replacement of fine aggregate (by volume of 5%, 10%, 15%, 20% and 25%). The concrete mixes were evaluated for compressive strength, flexural strength, resistance to impact loading, fatigue loading, water penetration and shrinkage strain was evaluated. It was observed that inclusion of rubber ash resulted in the improvement of impact resistance of concrete. The results also show that up to 10% rubber ash and rubber fibers can be utilized as fine aggregate to develop feasible and durable rubberized concrete pavements, crash barriers and paver blocks.

     

Evaluation of fruit-vegetable and fish wastes as alternative feedstuffs in pig diets

Fruit-vegetable and fish wastes were evaluated as potential feedstuffs for growing-finishing pigs. Wastes were collected from shops in the city of Salamanca (Spain) and their nutritional composition, mineral content and digestibility were determined. The dry matter of the wastes under study was relatively low (12% for fruit-vegetable waste and 26% for fish waste), but they presented all of the nutrient requirements for swine diets. The fish waste contained 58% crude protein, 22% ash, 19% ether extract and 1% crude fibre, whereas the fruit-vegetable waste contained 65% nitrogen free extract, 13% crude fibre, 12% crude protein, 8% ash and 2% ether extract. Waste digestibility decreased with temperature, and hence temperatures over 65 degrees C for fruit-vegetable waste and 105 degrees C for fish waste should not be used in the treatment to reduce the moisture and to ensure the microbiology quality. Therefore, two diets were formulated using linear programming. The analysed waste was included in approximately 20% of one of the diets, while another diet was formulated without any type of waste. These data showed that this part of biodegradable municipal waste could be managed as alternative feedstuffs in swine diets, reducing the amount of biodegradable municipal waste going to landfills.     

气相色谱法直接测定水中微量有机胺

用配有氢火焰离子化检测器（FID）的气相色谱仪直接测定水中多种微量有机胺。试样经过滤后直接进样,在气相色谱仪上使用CP7448毛细管柱,用外标法测定水中微量甲胺、二甲胺、一乙胺、二乙胺的含量。在所选择的色谱操作条件下,甲胺、二甲胺、一乙胺、二乙胺的质量浓度分别在一定范围内与峰面积呈良好的线性关系。4种组分的回收率分别为96.7％,99．0％,101．2％,99．2％;精密度分别为4．3％,3．7％,5．5％,3．1％;检出限分别为2．0,2．0,1．5,1．5mg/L。该方法操作简便,回收率、精密度高。     

A/O—Fenton氧化—混凝组合工艺处理丁苯橡胶生产废水

采用A/O—Fenton氧化—混凝组合工艺处理丁苯橡胶生产废水。试验结果表明:A/O工段中,在兼氧池HRT 8 h、好氧池HRT 16 h、好氧池MLSS 2 500~3 500 mg/L的优化参数下,平均COD,NH3-N,TP去除率分别为72.9%,96.2%,51.3%;Fenton氧化工段中,在30%(w)H2O2溶液加入量0.2%(φ)、n(H2O2)∶n(Fe SO4)=2∶1、Fenton氧化反应时间70 min、Fenton氧化进水p H 5.0的优化条件下,COD和TP的去除率分别为56.0%和57.0%;A/O—Fenton氧化—混凝组合工艺对COD、NH3-N、TP、浊度的总去除率分别为94.8%,96.2%,100%,94.0%,处理后出水满足GB 8978—1996《污水综合排放标准》中的一级标准。     

磁选柱在矿山磁选尾矿和硫铁矿烧渣处理中的应用

介绍了磁选柱的结构、分选原理、分选过程及其在处理矿山磁选尾矿和硫铁矿烧渣方面的应用。用磁选柱精选磁铁矿尾矿，得到的精矿品位大于66％；用磁选柱精选硫铁矿烧渣，得到的精矿品位大于65％。硫的质量分数降至0．84％。     

Co-combustion of waste from olive oil production with coal in a fluidised bed

Waste from olive oil production was co-fired with coal in a fluidised bed combustor to study the feasibility of using this waste as an energy source. The combustion efficiency and CO emission were investigated and compared to those of burning 100% of coal. Olive oil waste with up to 20% mass concentration can be co-fired with coal in a fluidised bed combustor designed for coal combustion with a maximum drop of efficiency of 5%. A 10% olive oil waste concentration gave a lower CO emission than 100% coal firing due to improved combustion in the freeboard region. A 20% olive oil waste mixture gave a higher CO emission than both 100% coal firing and 10% olive oil waste mixture, but the combustion efficiency was higher than the 10% olive oil waste mixture due to lower elutriation from the bed.     

苯基周位酸生产废水处理试验研究

采用CHA－111大孔吸附树脂对苯基周位酸生产过程排放的汽提苯胺盐析废水和苯基周位酸酸析母液进行处理试验,效果良好。汽提苯胺盐析废水苯胺质量浓度＞1600mg／L,经树脂吸附处理后苯胺质量浓度＜2mg／L,苯胺去除率＞99．9％,COD去除率＞97％,树脂工作吸附量达120g／L,脱附率＞98％;苯基周位酸酸析母液经树脂吸附、混凝沉淀处理后,苯基周位酸质量浓度＜190mg／L,苯基周位酸去除率为94．8％,COD去除率为94．3％,氨基值去除率为80％,脱附率＞99％。     

废水中甲醇分析方法的研究

建立了废水中甲醇的3种分析方法,毛细管柱气相色谱法、填充柱气相色谱法和变色酸分光光度法。测定废水中甲醇浓度相对标准偏差分别为1．45％,2．93％,3．61％,平均回收率分别为100．88％,98．19％,97．62％。实验结果表明：3种方法能较好对应,其中毛细管柱气相色谱法灵敏度最高,方法检出限为0．05mg／L。     

混凝—气浮工艺处理有机物污染地下水现场中试试验

对某农药厂原厂区的有机污染地下水的水质特征进行了分析,采用小试确定了药剂投加量,并采用中试装置考察了混凝—气浮工艺的去除效果。小试结果表明,聚合氯化铝（PAC）的最佳投加量为300 mg/L,聚丙烯酰胺（PAM）的最佳投加量为3 mg/L。中试运行结果表明,当进水流量为0.25 ~1.00 m3/h时,对浊度的去除率为82.66%~90.13%,对悬浮固体的去除率为80.12%~90.11%;碳原子数在10~28范围内的石油烃的平均去除率为38.96%~51.46%;1,2-二氯乙烷、2-甲基萘、苯、萘、甲苯、邻苯二甲酸二甲酯的平均去除率分别为17.76%,67.49%,48.70%,54.56%,37.24%,62.53%。